Self-Limiting Phase Transition Enabling Reversible Overstoichiometric Li Storage in Ni-Rich Cathodes.

Ni-rich cathodes are some of the most promising candidates for advanced lithium-ion batteries, but their available capacities have been stagnant due to the intrinsic Li+ storage sites. Extending the voltage window down can induce the phase transition from O3 to 1T of LiNiO2-derived cathodes to accommodate excess Li+ and dramatically increase the capacity. By setting the discharge cutoff voltage of LiNi0.6Co0.2Mn0.2O2 to 1.4 V, we can reach an extremely high capacity of 393 mAh g-1 and an energy density of 1070 Wh kg-1 here. However, the phase transition causes fast capacity decay and related structural evolution is rarely understood, hindering the utilization of this feature. We find that the overlithiated phase transition is self-limiting, which will transform into solid-solution reaction with cycling and make the cathode degradation slow down. This is attributed to the migration of abundant transition metal ions into lithium layers induced by the overlithiation, allowing the intercalation of overstoichiometric Li+ into the crystal without the O3 framework change. Based on this, the wide-potential cycling stability is further improved via a facile charge-discharge protocol. This work provides deep insight into the overstoichiometric Li+ storage behaviors in conventional layered cathodes and opens a new avenue toward high-energy batteries.

Nonconventional Electrochemical Reactions in Rechargeable Lithium-Sulfur Batteries.

Rechargeable lithium-sulfur (Li-S) batteries are promising for high-energy storage. However, conventional redox reactions involving sulfur (S) and lithium (Li) can lead to unstable intermediates. Over the past decade, many strategies have emerged to address this challenge, enabling nonconventional electrochemical reactions in Li-S batteries. In our Perspective, we provide a brief review of these strategies and highlight their potential benefits. Specifically, our group has pioneered a top-down approach, investigating Li-S reactions at molecular and subatomic levels, as demonstrated in our recent work on stable S isotopes. These insights not only enhance understanding of charge transfer and storage properties but also offer exciting opportunities for advancements in battery materials research.

Boosting Sodium Compensation Efficiency via a CNT/MnO2 Catalyst toward High-Performance Na-Ion Batteries.

The formation of a solid electrolyte interphase on carbon anodes causes irreversible loss of Na+ ions, significantly compromising the energy density of Na-ion full cells. Sodium compensation additives can effectively address the irreversible sodium loss but suffer from high decomposition voltage induced by low electrochemical activity. Herein, we propose a universal electrocatalytic sodium compensation strategy by introducing a carbon nanotube (CNT)/MnO2 catalyst to realize full utilization of sodium compensation additives at a much-reduced decomposition voltage. The well-organized CNT/MnO2 composite with high catalytic activity, good electronic conductivity, and abundant reaction sites enables sodium compensation additives to decompose at significantly reduced voltages (from 4.40 to 3.90 V vs Na+/Na for sodium oxalate, 3.88 V for sodium carbonate, and even 3.80 V for sodium citrate). As a result, sodium oxalate as the optimal additive achieves a specific capacity of 394 mAh g-1, almost reaching its theoretical capacity in the first charge, increasing the energy density of the Na-ion full cell from 111 to 158 Wh kg-1 with improved cycle stability and rate capability. This work offers a valuable approach to enhance sodium compensation efficiency, promising high-performance energy storage devices in the future.

An ultralight, pulverization-free integrated anode toward lithium-less lithium metal batteries.

The high-capacity advantage of lithium metal anode was compromised by common use of copper as the collector. Furthermore, lithium pulverization associated with "dead" Li accumulation and electrode cracking deteriorates the long-term cyclability of lithium metal batteries, especially under realistic test conditions. Here, we report an ultralight, integrated anode of polyimide-Ag/Li with dual anti-pulverization functionality. The silver layer was initially chemically bonded to the polyimide surface and then spontaneously diffused in Li solid solution and self-evolved into a fully lithiophilic Li-Ag phase, mitigating dendrites growth or dead Li. Further, the strong van der Waals interaction between the bottommost Li-Ag and polyimide affords electrode structural integrity and electrical continuity, thus circumventing electrode pulverization. Compared to the cutting-edge anode-free cells, the batteries pairing LiNi0.8Mn0.1Co0.1O2 with polyimide-Ag/Li afford a nearly 10% increase in specific energy, with safer characteristics and better cycling stability under realistic conditions of 1× excess Li and high areal-loading cathode (4 milliampere hour per square centimeter).

A Fast-Charge Graphite Anode with a Li-Ion-Conductive, Electron/Solvent-Repelling Interface.

Graphite has been serving as the key anode material of rechargeable Li-ion batteries, yet is difficultly charged within a quarter hour while maintaining stable electrochemistry. In addition to a defective edge structure that prevents fast Li-ion entry, the high-rate performance of graphite could be hampered by co-intercalation and parasitic reduction of solvent molecules at anode/electrolyte interface. Conventional surface modification by pitch-derived carbon barely isolates the solvent and electrons, and usually lead to inadequate rate capability to meet practical fast-charge requirements. Here we show that, by applying a MoOx-MoNx layer onto graphite surface, the interface allows fast Li-ion diffusion yet blocks solvent access and electron leakage. By regulating interfacial mass and charge transfer, the modified graphite anode delivers a reversible capacity of 340.3 mAh g-1 after 4000 cycles at 6 C, showing promises in building 10-min-rechargeable batteries with a long operation life.

Reduced Volume Expansion of Micron-Sized SiOx via Closed-Nanopore Structure Constructed by Mg-Induced Elemental Segregation.

The inherently huge volume expansion during Li uptake has hindered the use of Si-based anodes in high-energy lithium-ion batteries. While some pore-forming and nano-architecting strategies show promises to effectively buffer the volume change, other parameters essential for practical electrode fabrication, such as compaction density, are often compromised. Here we propose a new in situ Mg doping strategy to form closed-nanopore structure into a micron-sized SiOx particle at a high bulk density. The doped Mg atoms promote the segregation of O, so that high-density magnesium silicates form to generate closed nanopores. By altering the mass content of Mg dopant, the average radii (ranged from 5.4 to 9.7 nm) and porosities (ranged from 1.4 % to 15.9 %) of the closed pores are precisely adjustable, which accounts for volume expansion of SiOx from 77.8 % to 22.2 % at the minimum. Benefited from the small volume variation, the Mg-doped micron-SiOx anode demonstrates improved Li storage performance towards realization of a 700-(dis)charge-cycle, 11-Ah-pouch-type cell at a capacity retention of >80 %. This work offers insights into reasonable design of the internal structure of micron-sized SiOx and other materials that undergo conversion or alloying reactions with drastic volume change, to enable high-energy batteries with stable electrochemistry.

The electrochemistry of stable sulfur isotopes versus lithium.

Sulfur in nature consists of two abundant stable isotopes, with two more neutrons in the heavy one (34S) than in the light one (32S). The two isotopes show similar physicochemical properties and are usually considered an integral system for chemical research in various fields. In this work, a model study based on a Li-S battery was performed to reveal the variation between the electrochemical properties of the two S isotopes. Provided with the same octatomic ring structure, the cyclo-34S8 molecules form stronger S-S bonds than cyclo-32S8 and are more prone to react with Li. The soluble Li polysulfides generated by the Li-34S conversion reaction show a stronger cation-solvent interaction yet a weaker cation-anion interaction than the 32S-based counterparts, which facilitates quick solvation of polysulfides yet hinders their migration from the cathode to the anode. Consequently, the Li-34S cell shows improved cathode reaction kinetics at the solid-liquid interface and inhibited shuttle of polysulfides through the electrolyte so that it demonstrates better cycling performance than the Li-32S cell. Based on the varied shuttle kinetics of the isotopic-S-based polysulfides, an electrochemical separation method for 34S/32S isotope is proposed, which enables a notably higher separation factor than the conventional separation methods via chemical exchange or distillation and brings opportunities to low-cost manufacture, utilization, and research of heavy chalcogen isotopes.

Fast Na+ Kinetics and Suppressed Voltage Hysteresis Enabled by a High-Entropy Strategy for Sodium Oxide Cathodes.

O3-type layered transition metal cathodes are promising energy storage materials due to their sufficient sodium reservoir. However, sluggish sodium ions kinetics and large voltage hysteresis, which are generally associated with Na+ diffusion properties and electrochemical phase transition reversibility, drastically minimize energy density, reduce energy efficiency, and hinder further commercialization of sodium-ion batteries (SIBs). Here, this work proposes a high-entropy tailoring strategy through manipulating the electronic local environment within transition metal slabs to circumvent these issues. Experimental analysis combined with theoretical calculations verify that high-entropy metal ion mixing contributes to the improved reversibility of redox reaction and O3-P3-O3 phase transition behaviors as well as the enhanced Na+ diffusivity. Consequently, the designed O3-Na0.9Ni0.2Fe0.2Co0.2Mn0.2Ti0.15Cu0.05O2 material with high-entropy characteristic could display a negligible voltage hysteresis (<0.09 V), impressive rate capability (98.6 mAh g-1 at 10 C) and long-term cycling stability (79.4% capacity retention over 2000 cycles at 5 C). This work provides insightful guidance in mitigating the voltage hysteresis and facilitating Na+ diffusion of layered oxide cathode materials to realize high-rate and high-energy SIBs.

Anchoring Active Li Metal in Oriented Channel by In Situ Formed Nucleation Sites Enabling Durable Lithium-Metal Batteries.

Lithium metal is the ultimate anode material for pursuing the increased energy density of rechargeable batteries. However, fatal dendrites growth and huge volume change seriously hinder the practical application of lithium metal batteries (LMBs). In this work, a lithium host that preinstalled CoSe nanoparticles on vertical carbon vascular tissues (VCVT/CoSe) is designed and fabricated to resolve these issues, which provides sufficient Li plating space with a robust framework, enabling dendrite-free Li deposition. Their inherent N sites coupled with the in situ formed lithiophilic Co sites loaded at the interface of VCVT not only anchor the initial Li nucleation seeds but also accelerate the Li+ transport kinetics. Meanwhile, the Li2 Se originated from the CoSe conversion contributes to constructing a stable solid-electrolyte interphase with high ionic conductivity. This optimized Li/VCVT/CoSe composite anode exhibits a prominent long-term cycling stability over 3000 h with a high areal capacity of 10 mAh cm-2 . When paired with a commercial nickel-rich LiNi0.83 Co0.12 Mn0.05 O2 cathode, the full-cell presents substantially enhanced cycling performance with 81.7% capacity retention after 300 cycles at 0.2 C. Thus, this work reveals the critical role of guiding Li deposition behavior to maintain homogeneous Li morphology and pave the way to stable LMBs.

Nanoscale Visualization of Lithium Plating/Stripping Tuned by On-site Formed Solid Electrolyte Interphase in All-Solid-State Lithium-Metal Batteries.

The interfacial processes, mainly the lithium (Li) plating/stripping and the evolution of the solid electrolyte interphase (SEI), are directly related to the performance of all-solid-state Li-metal batteries (ASSLBs). However, the complex processes at solid-solid interfaces are embedded under the solid-state electrolyte, making it challenging to analyze the dynamic processes in real time. Here, using in situ electrochemical atomic force microscopy and optical microscopy, we directly visualized the Li plating/stripping/replating behavior, and measured the morphological and mechanical properties of the on-site formed SEI at nanoscale. Li spheres plating/stripping/replating at the argyrodite solid electrolyte (Li6 PS5 Cl)/Li electrode interface is coupled with the formation/wrinkling/inflating of the SEI on its surface. Combined with in situ X-ray photoelectron spectroscopy, details of the stepwise formation and physicochemical properties of SEI on the Li spheres are obtained. It is shown that higher operation rates can decrease the uniformity of the Li+ -conducting networks in the SEI and worsen Li plating/stripping reversibility. By regulating the applied current rates, uniform nucleation and reversible plating/stripping processes can be achieved, leading to the extension of the cycling life. The in situ analysis of the on-site formed SEI at solid-solid interfaces provides the correlation between the interfacial evolution and the electrochemical performance in ASSLBs.

A Fully Amorphous, Dynamic Cross-Linked Polymer Electrolyte for Lithium-Sulfur Batteries Operating at Subzero-Temperatures.

Solid-state lithium-sulfur batteries have shown prospects as safe, high-energy electrochemical storage technology for powering regional electrified transportation. Owing to limited ion mobility in crystalline polymer electrolytes, the battery is incapable of operating at subzero temperature. Addition of liquid plasticizer into the polymer electrolyte improves the Li-ion conductivity yet sacrifices the mechanical strength and interfacial stability with both electrodes. In this work, we showed that by introducing a spherical hyperbranched solid polymer plasticizer into a Li+ -conductive linear polymer matrix, an integrated dynamic cross-linked polymer network was built to maintain fully amorphous in a wide temperature range down to subzero. A quasi-solid polymer electrolyte with a solid mass content >90 % was prepared from the cross-linked polymer network, and demonstrated fast Li+ conduction at a low temperature, high mechanical strength, and stable interfacial chemistry. As a result, solid-state lithium-sulfur batteries employing the new electrolyte delivered high reversible capacity and long cycle life at 25 °C, 0 °C and -10 °C to serve energy storage at complex environmental conditions.

Precursor Induced Assembly of Si Nanoparticles Encapsulated in Graphene/Carbon Matrices and the Influence of Al2 O3 Coating on their Properties as Anode for Lithium-Ion Batteries.

The theoretical capacity of pristine silicon as anodes for lithium-ion batteries (LIBs) can reach up to 4200 mAh g-1 , however, the low electrical conductivity and the huge volume expansion limit their practical application. To address this challenge, a precursor strategy has been explored to induce the curling of graphene oxide (GO) flakes and the enclosing of Si nanoparticles by selecting protonated chitosan as both assembly inducer and carbon precursor. The Si nanoparticles are dispersed first in a slurry of GO by ball milling, then the resulting dispersion is dried by a spray drying process to achieve instantaneous solution evaporation and compact encapsulation of silicon particles with GO. An Al2 O3 layer is constructed on the surface of Si@rGO@C-SD composites by the atomic layer deposition method to modify the solid electrolyte interface. This strategy enhances obviously the electrochemical performance of the Si as anode for LIBs, including excellent long-cycle stability of 930 mAh g-1 after 1000 cycles at 1000 mA g-1 , satisfied initial Coulomb efficiency of 76.7%, and high rate ability of 806 mAh g-1 at 5000 mA g-1 . This work shows a potential solution to the shortcomings of Si-based anodes and provides meaningful insights for constructing high-energy anodes for LIBs.

Tailoring chemical composition of solid electrolyte interphase by selective dissolution for long-life micron-sized silicon anode.

Micron-sized Si anode promises a much higher theoretical capacity than the traditional graphite anode and more attractive application prospect compared to its nanoscale counterpart. However, its severe volume expansion during lithiation requires solid electrolyte interphase (SEI) with reinforced mechanical stability. Here, we propose a solvent-induced selective dissolution strategy to in situ regulate the mechanical properties of SEI. By introducing a high-donor-number solvent, gamma-butyrolactone, into conventional electrolytes, low-modulus components of the SEI, such as Li alkyl carbonates, can be selectively dissolved upon cycling, leaving a robust SEI mainly consisting of lithium fluoride and polycarbonates. With this strategy, raw micron-sized Si anode retains 87.5% capacity after 100 cycles at 0.5 C (1500 mA g-1, 25°C), which can be improved to >300 cycles with carbon-coated micron-sized Si anode. Furthermore, the Si||LiNi0.8Co0.1Mn0.1O2 battery using the raw micron-sized Si anode with the selectively dissolved SEI retains 83.7% capacity after 150 cycles at 0.5 C (90 mA g-1). The selective dissolution effect for tailoring the SEI, as well as the corresponding cycling life of the Si anodes, is positively related to the donor number of the solvents, which highlights designing high-donor-number electrolytes as a guideline to tailor the SEI for stabilizing volume-changing alloying-type anodes in high-energy rechargeable batteries.

Refined Electrolyte and Interfacial Chemistry toward Realization of High-Energy Anode-Free Rechargeable Sodium Batteries.

Anode-free rechargeable sodium batteries represent one of the ultimate choices for the 'beyond-lithium' electrochemical storage technology with high energy. Operated based on the sole use of active Na ions from the cathode, the anode-free battery is usually reported with quite a limited cycle life due to unstable electrolyte chemistry that hinders efficient Na plating/stripping at the anode and high-voltage operation of the layered oxide cathode. A rational design of the electrolyte toward improving its compatibility with the electrodes is key to realize the battery. Here, we show that by refining the volume ratio of two conventional linear ether solvents, a binary electrolyte forms a cation solvation structure that facilitates flat, dendrite-free, planar growth of Na metal on the anode current collector and that is adaptive to high-voltage Na (de)intercalation of P2-/O3-type layered oxide cathodes and oxidative decomposition of the Na2C2O4 supplement. Inorganic fluorides, such as NaF, show a major influence on the electroplating pattern of Na metal and effective passivation of plated metal at the anode-electrolyte interface. Anode-free batteries based on the refined electrolyte have demonstrated high coulombic efficiency, long cycle life, and the ability to claim a cell-level specific energy of >300 Wh/kg.

Potential Controllable Redox Couple for Mild and Efficient Lithium Recovery from Spent Batteries.

The prosperity of the lithium-ion battery market is dialectically accompanied by the depletion of corresponding resources and the accumulation of spent batteries. It is an urgent priority to develop green and efficient battery recycling strategies for helping ease resources and environmental pressures at the current stage. Here, we propose a mild and efficient lithium extracting strategy based on potential controllable redox couples. Active lithium in the spent battery without discharging is extracted using a series of tailored aprotic solutions comprised of polycyclic aromatic hydrocarbons and ethers. This ensures a safe yet efficient recycling process with nearly ≈100 % lithium recovery. We further investigate the Li+ -electron concerted redox reactions and the effect of solvation structure on kinetics during the extraction, and broaden the applicability of the Li-PAHs solution. This work can stimulate new inspiration for designing novel solutions to meet efficient and sustainable demands in recycling batteries.

Insights into Anion-Solvent Interactions to Boost Stable Operation of Ether-Based Electrolytes in Pure-SiOx ||LiNi0.8 Mn0.1 Co0.1 O2 Full Cells.

Ether solvents with superior reductive stability promise excellent interphasial stability with high-capacity anodes while the limited oxidative resistance hinders their high-voltage operation. Extending the intrinsic electrochemical stability of ether-based electrolytes to construct stable-cycling high-energy-density lithium-ion batteries is challenging but rewarding. Herein, the anion-solvent interactions were concerned as the key point to optimize the anodic stability of the ether-based electrolytes and an optimized interphase was realized on both pure-SiOx anodes and LiNi0.8 Mn0.1 Co0.1 O2 cathodes. Specifically, the small-anion-size LiNO3 and tetrahydrofuran with high dipole moment to dielectric constant ratio realized strengthened anion-solvent interactions, which enhance the oxidative stability of the electrolyte. The designed ether-based electrolyte enabled a stable cycling performance over 500 cycles in pure-SiOx ||LiNi0.8 Mn0.1 Co0.1 O2 full cell, demonstrating its superior practical prospects. This work provides new insight into the design of new electrolytes for emerging high-energy density lithium-ion batteries through the regulation of interactions between species in electrolytes.

Chemical-Mechanical Robustness of Single-Crystalline Ni-Rich Cathode Enabled by Surface Atomic Arrangement Control.

Layered transition metal oxide cathodes have been one of the dominant cathodes for lithium-ion batteries with efficient Li+ intercalation chemistry. However, limited by the weak layered interaction and unstable surface, mechanical and chemical failure plagues their electrochemical performance, especially for Ni-rich cathodes. Here, adopting a simultaneous elemental-structural atomic arrangement control based on the intrinsic Ni-Co-Mn system, the surface role is intensively investigated. Within the invariant oxygen sublattice of the crystal, a robust surface with the synergistic concentration gradient and layered-spinel intertwined structure is constructed on the model single-crystalline Ni-rich cathode. With mechanical strain dissipation and chemical erosion suppression, the cathode exhibits an impressive capacity retention of 82 % even at the harsh 60 °C after 150 cycles at 1 C. This work highlights the coupling effect of structure and composition on the chemical-mechanical properties, and the concept will spur more researches on the cathodes that share the same sublattice.

High-Performance Quasi-Solid-State Lithium-Sulfur Battery with a Controllably Solidified Cathode-Electrolyte Interface.

Lithium-sulfur batteries are considered a promising "beyond Li-ion" energy storage technology. Currently, the practical realization of Li-S batteries is plagued by rapid electrochemical failure of S cathodes due to aggravated polysulfide dissolution and shuttle in the conventional liquid ether-based electrolytes. A gel polymer electrolyte obtained by in situ polymerization of liquid electrolyte solvent at the cathode-electrolyte interface has been proven an effective strategy to prevent polysulfide shuttle. However, notably reduced polysulfide solubility in the gel electrolyte leads to enrichment of poorly conductive sulfide species, which hinders charge migration across the interface and therefore accounts for retarded polysulfide conversion and a low capacity/energy output of batteries. Here, we show that thioacetamide, as a cathode additive, inhibits interfacial polymerization of ether molecules while assisting dissolution of polysulfides and Li2S at the cathode/electrolyte interface. In this way, a layer of liquid, sulfide-soluble electrolyte is preserved between the highly gelled electrolyte and the S particle surface, avoiding interfacial sulfide accumulation and improving polysulfide conversion kinetics. A Li-S battery with the controllably solidified interface demonstrates, without adding other performance-boosting agents or catalysts, a high reversible capacity, a long cycle life, and a favorable rate performance, showing promises for the next-generation storage applications.

A Self-Reconfigured, Dual-Layered Artificial Interphase Toward High-Current-Density Quasi-Solid-State Lithium Metal Batteries.

The uncontrollable dendrite growth and unstable solid electrolyte interphase have long plagued the practical application of Li metal batteries. Herein, a dual-layered artificial interphase LiF/LiBO-Ag is demonstrated that is simultaneously reconfigured via an electrochemical process to stabilize the lithium anode. This dual-layered interphase consists of a heterogeneous LiF/LiBO glassy top layer with ultrafast Li-ion conductivity and lithiophilic Li-Ag alloy bottom layer, which synergistically regulates the dendrite-free Li deposition, even at high current densities. As a result, Li||Li symmetric cells with LiF/LiBO-Ag interphase achieve an ultralong lifespan (4500 h) at an ultrahigh current density and area capacity (20 mA cm-2 , 20 mAh cm-2 ). LiF/LiBO-Ag@Li anodes are successfully applied in quasi-solid-state batteries, showing excellent cycling performances in symmetric cells (8 mA cm-2 , 8 mAh cm-2 , 5000 h) and full cells. Furthermore, a practical quasi-solid-state pouch cell coupling with a high-nickel cathode exhibits stable cycling with a capacity retention of over 91% after 60 cycles at 0.5 C, which is comparable or even better than that in liquid-state pouch cells. Additionally, a high-energy-density quasi-solid-state pouch cell (10.75 Ah, 448.7 Wh kg-1 ) is successfully accomplished. This well-orchestrated interphase design provides new guidance in engineering highly stable interphase toward practical high-energy-density lithium metal batteries.

Size controllable single-crystalline Ni-rich cathodes for high-energy lithium-ion batteries.

A single-crystalline Ni-rich (SCNR) cathode with a large particle size can achieve higher energy density, and is safer, than polycrystalline counterparts. However, synthesizing large SCNR cathodes (>5 µm) without compromising electrochemical performance is very challenging due to the incompatibility between Ni-rich cathodes and high temperature calcination. Herein, we introduce Vegard's Slope as a guide for rationally selecting sintering aids, and we successfully synthesize size-controlled SCNR cathodes, the largest of which can be up to 10 µm. Comprehensive theoretical calculation and experimental characterization show that sintering aids continuously migrate to the particle surface, suppress sublattice oxygen release and reduce the surface energy of the typically exposed facets, which promotes grain boundary migration and elevates calcination critical temperature. The dense SCNR cathodes, fabricated by packing of different-sized SCNR cathode particles, achieve a highest electrode press density of 3.9 g cm-3 and a highest volumetric energy density of 3000 Wh L-1. The pouch cell demonstrates a high energy density of 303 Wh kg-1, 730 Wh L-1 and 76% capacity retention after 1200 cycles. SCNR cathodes with an optimized particle size distribution can meet the requirements for both electric vehicles and portable devices. Furthermore, the principle for controlling the growth of SCNR particles can be widely applied when synthesizing other materials for Li-ion, Na-ion and K-ion batteries.