Enhancement of sludge dewaterability by repeated inoculation of acidified sludge: Extracellular polymeric substances molecular structure and microbial community succession.

Improving the dewatering performance of sewage sludge is of great scientific and engineering significance in the context of accelerated urbanization and increasingly strict environmental regulations. Acidified sludge (AS) can improve sludge dewatering performance, but the dewatering effect of repeated inoculation is unclear. The effects of long-term repeated inoculation of AS on the sludge dewaterability were investigated. The molecular structure and microbial community succession of extracellular polymeric substances (EPS) are emphasized. The results revealed that increasing the inoculation ratio of AS reduced the pH, absolute value of sludge zeta potential, and sludge particle size, and the decreasing trend was more evident with prolonging treatment time. Under the conditions of 30% and 50% AS inoculation, the dewatering performance of the sludge was significantly improved (p < 0.05). Compared with the raw sludge, the specific resistance of filtration (SRF) and capillary suction time of 30% inoculation were reduced by 64.3% and 50.1% after 30 cycles, respectively. Excluding loosely bound (LB)-EPS, soluble (S)-EPS and tightly bound (TB)-EPS exhibited a visible decrease, the protein in TB-EPS was significantly related to sludge dewaterability (p < 0.05). The fluorescent components of aromatic protein and fulvic acid-like substances in TB-EPS were significantly associated with SRF, with a correlation coefficient 0.99 (p < 0.05). Both the increase in the percentages of random coil and decrease in α-helix in TB-EPS contributed to improving dewaterability. Increasing Firmicutes and decreasing Chloroflexi levels improved the sludge dewatering capacity. Repeated inoculation did not disrupt the dewatering effect of AS rather increased the feasibility of the engineering application of AS. Considering the dewatering performance and cost synthetically, 30% AS inoculated ratio is feasible for practical applications.

Effects of changes in the structural parameters of bionic straw sandwich concrete beetle elytron plates on their mechanical and thermal insulation properties.

To develop new, environmentally friendly prefabricated building materials, the effects of individual changes in structural parameters on the mechanical and thermal insulation properties of straw sandwich concrete beetle elytron plates (SCBEPs), i.e., sandwich plates with trabeculae constituting the core layer structure, were analyzed by ABAQUS. In addition, based on the analysis results, the structural parameters were preliminarily optimized. The results revealed the following. 1) The bearing capacity of a SCBEP is mainly controlled by deformation (i.e., the maximum deflection). The two most influencing factors on the deflection are the panel thickness T and the trabecular radius R. In contrast, although the panel area is very large, the influence of changing the panel thickness on the thermal insulation performance ranks only third. This demonstrates that the thermal bridge effect of the concrete trabeculae and edges is the primary limitation on further improvements to the thermal insulation performance of SCBEPs. 2) Based on the effects of individual changes in structural parameters on the performance of SCBEPs and their actual processing and application requirements, the structural parameters of a SCBEP with optimized mechanical properties and thermal insulation properties are determined. 3) Compared with aerated concrete wallboards, the optimized SCBEP has a higher rigidity, more compacted surface and better durability. Compared with straw concrete wallboards, the optimized SCBEP has a higher straw content and better thermal insulation performance. Thus, it provides a new avenue for the development of a new, lightweight wallboard.

Structural characteristics of the core layer and biomimetic model of the ladybug forewing.

To explore the characteristics of the core structure of ladybug (Harmonia axyridis) forewings, their microstructure was studied using microscopes. The results suggest that trabeculae exist in the frame of the beetle (ladybug) forewing for the first time; this study represents the first determination of the parameters N, the total number of trabeculae in each forewing, and λt, the ratio of the cross-sectional area of the trabeculae to the effective area of trabecular distribution. The cross-sectional area of a single trabecula in the ladybug forewing is smaller than those in two other kinds of beetles, Allomyrina dichotoma and Prosopocoilus inclinatus. However, the average trabecular density of the ladybug forewing is 84 per square millimeter, which is the highest among these three kinds of beetles. The λt values are 1.0%, 1.5% and 10.5% for H. axyridis, A. dichotoma and P. inclinatus, respectively, and the corresponding N values are approximately 1.4, 1.7 and 3.7 thousand, respectively. Based on these findings, a biomimetic model of the ladybug forewing is proposed, which is characterized by a core structure with a high-density distribution of thin trabeculae surrounded by a foam-like material.

The 3D lightweight structural characteristics of the beetle forewing.

The present paper renewedly expounds upon the characteristics of the 3D lightweight structure of beetle forewings and notes that two biomimetic structures (models) that have appeared in recent years do not comply with these characteristics based on a comparison of the structures of the biological prototypes. The first model features transverse tubules based on observations of circular holes in cross-sectional figures of the Cybister forewing. The second is a biomimetic spherical cavity model with hollow trabeculae that reportedly exhibits superior mechanical properties because its structures are most similar to the biological prototype. Finally, a false biomimetic proposition that the mechanical properties of biomimetic structures with "fiber winding" patterns are superior to those of structures constructed of pure "epoxy" is also noted. Hopefully, the present study can serve to improve the state of research on biomimetic applications of beetle forewing structures.