Microplastic analysis in sediments of the Elbe River by electrostatic separation and differential scanning calorimetry.

This study presents the most extensive investigation of microplastic (MP) contents in sediment from the Elbe River. We employed electrostatic separation (ES) and differential scanning calorimetry (DSC) to overcome limitations of sample throughput and time-consuming analysis. In total 43 sediment samples were collected using a Van-Veen grab. Subsequently, coarse materials (d10 > 100 µm) and fine materials (d10 ≤ 100 µm) were enriched using ES and density separation. DSC was utilized for MP identification and quantification, based on the phase-transition signals of eight different polymers. MP presence was detected in 25 samples, with successful quantification in 12 samples. The MP content in coarse material samples from shoreline areas ranged from 0.52 to 1.30 mg/kg, while in fine material samples from harbor basins, it ranged from 5.0 to 44.6 mg/kg. The most prevalent polymers identified were LD-PE, HD-PE, PP, and PCL. These findings confirmed the suitability of DSC for analyzing MP in complex environmental samples. MP hotspots were identified in harbor basins, where natural sedimentation processes and increased anthropogenic activities contribute to MP accumulation. Additionally, industrial sewage potentially contributed to MP content in sediment samples. The highest pollution levels were observed in the middle Elbe, between the confluences of Mulde and Havel. Lowest MP contents were found in the lower Elbe, potentially influenced by tides. Future studies should focus on holistic investigations of selected river sections, encompassing sediment, water, and biota samples, rather than the entire catchment area. This approach would facilitate the generation of spatiotemporal data on MP distribution in freshwater streams. In addition, more research is needed to explore potential interactions between different MP and sediment types during DSC measurements.

Regression analysis for the determination of microplastics in sediments using differential scanning calorimetry.

This research addresses the growing need for fast and cost-efficient methods for microplastic (MP) analysis. We present a thermo-analytical method that enables the identification and quantification of different polymer types in sediment and sand composite samples based on their phase transition behavior. Differential scanning calorimetry (DSC) was performed, and the results were evaluated by using different regression models. The melting and crystallization enthalpies or the change in heat capacity at the glass transition point were measured as regression analysis data. Ten milligrams of sea sand was spiked with 0.05 to 1.5 mg of microplastic particles (size: 100 to 200 µm) of the semi-crystalline polymers LD-PE, HD-PE, PP, PA6, and PET, and the amorphous polymers PS and PVC. The results showed that a two-factorial regression enabled the unambiguous identification and robust quantification of different polymer types. The limits of quantification were 0.13 to 0.33 mg and 0.40 to 1.84 mg per measurement for semi-crystalline and amorphous polymers, respectively. Moreover, DSC is robust with regard to natural organic matrices and allows the fast and non-destructive analysis of microplastic within the analytical limits. Hence, DSC could expand the range of analytical methods for microplastics and compete with perturbation-prone chemical analyses such as thermal extraction-desorption gas chromatography-mass spectrometry or spectroscopic methods. Further work should focus on potential changes in phase transition behavior in more complex matrices and the application of DSC for MP analysis in environmental samples.

Development of multifunctional highly-efficient bio-based fire-retardant poly(lactic acid) composites for simultaneously improving thermal, crystallization and fire safety properties.

Currently, it is still a huge challenge to prepare high performance eco-friendly poly(lactic acid) (PLA) with high thermal stability, good processability, excellent crystallization behavior, good transparency and highly-efficient fire safety. In this paper, a novel bio-based nucleation agent N-(furan-2-ylmethyl)-P,P-diphenylphosphinic amide (FPPA) was prepared and used for the fabrication of fire safety PLA/FPPA composites. The chemical structure of FPPA was measured by FTIR, NMR and MS. Further, the crystallization behavior, thermal stability, fire safety and mechanical properties of PLA/FPPA composites were performed by TGA, DSC, polarization microscope, LOI, UL94, cone calorimeter, DMA and, SEM, Raman, GC-MS, and TGA-FTIR. The results showed that the multifunctional FPPA not only had a high thermal stability and was a good nucleation agent for PLA. Moreover, only loading of 3 wt% FPPA increased the LOI of PLA from 19.0 to 33.8 % with UL-94 V-0 classification. Furthermore, the heat release rate and total heat release values of PLA/3%FPPA composite reduced by 6.3 % and 15.3 % in cone-calorimeter test. Such high fire safety was mainly attributed to specific fire safety radicals due to thermal degradation of FPPA to interrupt composites burning in gas phase. Besides, transparency and mechanical properties were almost not changed because of low loading of FPPA in PLA. This multifunctional bio-based fire-retardant for PLA with good comprehensive performance promises broad application in engineering electronics, automobiles, 3D printing and construction materials.

Stem Cells on Biomaterials for Synthetic Grafts to Promote Vascular Healing.

This review is divided into two interconnected parts, namely a biological and a chemical one. The focus of the first part is on the biological background for constructing tissue-engineered vascular grafts to promote vascular healing. Various cell types, such as embryonic, mesenchymal and induced pluripotent stem cells, progenitor cells and endothelial- and smooth muscle cells will be discussed with respect to their specific markers. The in vitro and in vivo models and their potential to treat vascular diseases are also introduced. The chemical part focuses on strategies using either artificial or natural polymers for scaffold fabrication, including decellularized cardiovascular tissue. An overview will be given on scaffold fabrication including conventional methods and nanotechnologies. Special attention is given to 3D network formation via different chemical and physical cross-linking methods. In particular, electron beam treatment is introduced as a method to combine 3D network formation and surface modification. The review includes recently published scientific data and patents which have been registered within the last decade.