Biomechanical and Histological Study of Retrieved LARS Synthetic Ligaments.

BACKGROUND: Synthetic grafts have been used for a number of years in anterior cruciate ligament (ACL) reconstruction surgery. One of the more recent additions to the stable of synthetic ligaments is the Ligament Augmentation and Reconstruction System (LARS) ligament. PURPOSE: To analyze the biomechanics and histology of LARS grafts retrieved due to failure of the device. STUDY DESIGN: Descriptive laboratory study. METHODS: A total of 22 LARS ligament grafts that were explanted from patients were sent for analysis. Five new, unused samples of the standard LARS ACL graft were also analyzed. Biomechanical testing was performed: ultimate tensile force, force versus displacement, and stress versus strain were recorded. Histopathological examination was performed looking for degree of fibrous tissue ingrowth as well as the presence of a foreign body reaction. RESULTS: Of the 22 grafts retrieved, 14 were used for ACL grafts, 1 for a lateral collateral ligament graft, 2 for medial collateral ligament grafts, 4 for gluteal tendon augmentation, and 1 for a supraspinatus augmentation. A severe foreign body reaction was found in 86% of the grafts (18/22) and a mild foreign body reaction in the remaining 14% (4/22). Tissue ingrowth was minimal in the majority of ACL grafts; the other grafts showed moderate tissue ingrowth. Maximal tensile force was significantly higher for the new ACL grafts (mean ± SD, 1667 ± 845 N) compared with the retrieved grafts (897 ± 395 N; P < .05). CONCLUSION: This study demonstrated that the vast majority of retrieved LARS artificial ligaments had a florid foreign body reaction. There was minimal tissue ingrowth in ACL grafts and moderate ingrowth in other grafts. Retrieved grafts had a decreased ultimate tensile force, which increased their risk of rupture. CLINICAL RELEVANCE: Surgeons should be cautious in choosing to use these grafts in reconstructive surgery for patients.

The COSPAR planetary protection requirements for space missions to Venus.

The Committee on Space Research's (COSPAR) Planetary Protection Policy states that all types of missions to Venus are classified as Category II, as the planet has significant research interest relative to the processes of chemical evolution and the origin of life, but there is only a remote chance that terrestrial contamination can proliferate and compromise future investigations. "Remote chance" essentially implies the absence of environments where terrestrial organisms could survive and replicate. Hence, Category II missions only require simplified planetary protection documentation, including a planetary protection plan that outlines the intended or potential impact targets, brief Pre- and Post-launch analyses detailing impact strategies, and a Post-encounter and End-of-Mission Report. These requirements were applied in previous missions and are foreseen for the numerous new international missions planned for the exploration of Venus, which include NASA's VERITAS and DAVINCI missions, and ESA's EnVision mission. There are also several proposed missions including India's Shukrayaan-1, and Russia's Venera-D. These multiple plans for spacecraft coincide with a recent interest within the scientific community regarding the cloud layers of Venus, which have been suggested by some to be habitable environments. The proposed, privately funded, MIT/Rocket Lab Venus Life Finder mission is specifically designed to assess the habitability of the Venusian clouds and to search for signs of life. It includes up to three atmospheric probes, the first one targeting a launch in 2023. The COSPAR Panel on Planetary Protection evaluated scientific data that underpins the planetary protection requirements for Venus and the implications of this on the current policy. The Panel has done a thorough review of the current knowledge of the planet's conditions prevailing in the clouds. Based on the existing literature, we conclude that the environmental conditions within the Venusian clouds are orders of magnitude drier and more acidic than the tolerated survival limits of any known terrestrial extremophile organism. Because of this future orbital, landed or entry probe missions to Venus do not require extra planetary protection measures. This recommendation may be revised in the future if new observations or reanalysis of past data show any significant increment, of orders of magnitude, in the water content and the pH of the cloud layer.

The COSPAR Planetary Protection Policy for robotic missions to Mars: A review of current scientific knowledge and future perspectives.

Planetary protection guidance for martian exploration has become a notable point of discussion over the last decade. This is due to increased scientific interest in the habitability of the red planet with updated techniques, missions becoming more attainable by smaller space agencies, and both the private sector and governments engaging in activities to facilitate commercial opportunities and human-crewed missions. The international standards for planetary protection have been developed through consultation with the scientific community and the space agencies by the Committee on Space Research's (COSPAR) Panel on Planetary Protection, which provides guidance for compliance with the Outer Space Treaty of 1967. In 2021, the Panel evaluated recent scientific data and literature regarding the planetary protection requirements for Mars and the implications of this on the guidelines. In this paper, we discuss the COSPAR Planetary Protection Policy for Mars, review the new scientific findings and discuss the next steps required to enable the next generation of robotic missions to Mars.

Fracture reduction has a dominant effect over cerclage wiring in increasing stiffness of intertrochanteric OTA/AO 31-A3.1 (reverse oblique) fractures managed with cephalomedullary osteosynthesis.

OBJECTIVES: To investigate the mechanical properties of cephalomedullary nailing of intertrochanteric OTA/AO 31-A3.1 (reverse oblique) fractures and to test the hypothesis that anatomical reduction and augmentation with cerclage wire produces a more stable construct. METHODS: A standardized fracture model in composite saw bone was created to stimulate an intertrochaneric 31-A3.1 fracture, using a 3D printed cutting guide. Simulated osteosynthesis was performed with 12 femurs divided into anatomically reduced and varus malreduced groups. Each femur was tested with and without cerclage wire augmentation. All femurs were fixed with a 215 mm, 130 degree, 11.5 mm nail. An Instron 8874 biaxial materials testing machine was used to assess the axial stiffness. Cyclic loading consisted of 5000 cycles of sinusoidal combined axial-torsion loading at 3 Hz. Axial load was 100 N to 2000 N and torsion -4.5 Nm to +4.5 Nm. Stiffness was measured before and after cyclic loading. RESULTS: Reduced constructs were stiffer than residual varus constructs. The mean overall fracture stiffness was 508.7 N/mm for reduced constructs and 379.2 N/mm for varus constructs. Removing the cables significantly decreased the fracture stiffness for both constructs (mean difference 60.0 N/mm, 95% CI 7.7-112.3, P = .032). CONCLUSIONS: Anatomical reduction has a dominant effect on facture stiffness. Anatomically reduced fractures are stiffer than varus malreduced fractures. A cerclage wire further improves construct stiffness if anatomical reduction is achieved. Cerclage wiring is less effective if anatomical reduction is not achieved.

Loosening of tibia baseplates after total knee arthroplasty: Evaluation of pull-out strength of tibia baseplate-cement Interface.

BACKGROUND: Aseptic loosening is reported as the leading cause of revision total knee arthroplasty on the Australian National Joint Replacement Registry. Loosening of cemented tibial baseplates has been correlated with type of cement used, cementing technique, and cement contamination with biological material. The aim of this study was to evaluate the effect of cementing application and techniques including surface contamination and cement viscosity on fixation strength of tibia baseplates/cement interface. METHODS: Mechanical assessment of the fixation strength of tibia baseplates/cement interface was tested using a pull-out test on a material testing system. Different tibial baseplate design, cementing techniques, cement viscosity and contamination of the implant/cement interface with bone marrow were assessed to determine if they influenced force required to disrupt the cement/implant interface (pull-out strength). FINDINGS: The model with contamination of the cement prosthesis interface demonstrated a lower pull-out strength (p < 0.001). The model with the keel and baseplate cemented showed a higher pull-out strength compared to cementing the baseplate alone (p < 0.001). The use of low-viscosity cement resulted in a significantly higher failure force (p = 0.002) compared to high-viscosity cement when cementing the baseplate alone. INTERPRETATIONS: Biomechanical testing demonstrated improved fixation with cementing the tibial keel and keeping surfaces free from contamination during the cementation process.

Biomechanical Comparison of a Notched Head Locking T-Plate and a Straight Locking Compression Plate in a Juxta-Articular Fracture Model.

OBJECTIVE: This investigation compared the biomechanical properties of a 2.0 mm locking compression notched head T-plate (NHTP) and 2.0 mm straight locking compression plate (LCP), in a simple transverse juxta-articular fracture model. STUDY DESIGN: Two different screw configurations were compared for the NHTP and LCP, modelling short (configuration 1) and long working length (configuration 2). Constructs were tested in compression, perpendicular and tension non-destructive four point bending and torsion. Plate surface strain was measured at 12 regions of interest (ROI) using three-dimensional digital image correlation. Stiffness and strain were compared between screw configurations within and between each plate. RESULTS: The LCP was stiffer than the NHTP in all three planes of bending and torsion (p < 0.05). The NHTP had greater strain than the LCP during compression bending and torsion at all ROI (p < 0.0005). The short working length was stiffer in all three planes of bending and in torsion (p < 0.05) than the longer working length for both plates. The long working length showed greater strain than the short working length at most ROI. CONCLUSION: In this experimental model, a 2.0 mm LCP with two screws in the short fragment was significantly stiffer and had lower plate strain than a 2.0 mm NHTP with three screws in the short fragment. Extending the working length significantly reduced construct stiffness and increased plate strain. These findings may guide construct selection.

Improved accuracy of CT based measurements for anterior prominence of acetabular prosthesis using a novel protocol based on anatomical landmarks.

BACKGROUND: Anterior hip pain after total hip replacement (THR) can be caused by iliopsoas impingement (IPI). Validation of CT measured cup version is well published; however quantification of the anterior cup prominence has not been validated. Therefore, we did an in vitro study aiming to: (1) assess the accuracy of the current method of measuring the prominence of the acetabular component using a dry bone model; (2) develop a CT protocol based on bony anatomical landmarks that improves the accuracy of these measurements. HYPOTHESIS: We hypothesise that utilising reproducible anatomical landmarks on the acetabulum will improve the accuracy of measurement of anterior prominence at the psoas valley. METHODS: A dry bone pelvic model was implanted with bilateral acetabular cups. The cup was manipulated into ten different combinations of inclination and version, and anterior prominence directly measured in relation to the acetabular rim. A CT scan was performed for each position. Anterior prominence was then measured by two radiologists, first using standard methods (axial slice at level of centre of femoral head) and then again using a novel protocol (based on the position of the psoas valley in relation to the inferior medial acetabular notch). RESULTS: Mean errors between direct measurement of anterior prominence and radiologist reported measurements using standard protocol were 6.94mm±5.24 (SD) (95%Confidence Interval: 3.25-4.27) and 5.14mm±3.07 (95%CI: 1.9-2.5) with a tendency towards overestimation of prominence. Using an anatomical landmark based protocol; mean error was reduced to 3.0mm±1.9 (95%CI: 1.16-1.53) and 4.3mm±4.3 (95%CI: 2.67-351) on the first attempt, and to 1.7mm±1.9 (95%CI: 1.15-1.52) and 2.1mm±1.4 (95%CI: 0.87-1.15) on the second attempt. Concordance correlation improved from 0.43 (95% CI: 0.19-0.68) and 0.59 (95% CI: 0.44-0.79) using the standard protocol, to 0.88 (95%CI: 0.61-0.91) and 0.9 (95%CI: 0.56-0.92) using the novel protocol. CONCLUSIONS: There is a difference in mean error and reliability between radiologically measured values for anterior prominence and values measured directly with present methods. The use of our novel protocol based on bony acetabular landmarks, significantly improves the accuracy of measurement. This protocol may improve reproducibility and the accuracy of this measurement and aid in the decision between tenotomy or revision of the acetabular component. LEVEL OF EVIDENCE: III, in vitro study comparing diagnostic tools.

Computer navigation of the glenoid component in reverse total shoulder arthroplasty: a clinical trial to evaluate the learning curve.

BACKGROUND: Intraoperative computer navigation has been introduced recently to assist with placement of the glenoid component. The aim of this study was to evaluate the learning curve of a single surgeon performing computer navigation of glenoid implant placement in primary reverse total shoulder arthroplasty (RTSA). METHODS: Following training with the intraoperative computer navigation system, we conducted a prospective case-series study of the first 24 consecutive patients undergoing a primary RTSA with navigation performed by a single surgeon. Surgical times, complications, and accuracy of glenoid positioning compared with the preoperative plan were evaluated. Surgical times were compared with the preceding non-navigated series of 24 consecutive primary RTSA cases. Postoperative 3-dimensional computed tomography scans were performed to evaluate glenoid component version and inclination compared with the preoperative plan. RESULTS: The total surgical time was 77.3 minutes (standard deviation [SD], 11.8 minutes) in the navigated RTSA cohort and 78.5 minutes (SD, 18.1 minutes) in the non-navigated series. A significant downward trend in the total surgical time was observed in the navigated cohort (P = .038), which flattened after 8 cases. No learning curve was observed in deviation of glenoid version or inclination from the preoperative plan. The mean deviation of achieved version from planned version was 3° (SD, 2°), and the mean deviation of achieved inclination from planned inclination was 5° (SD, 3°). CONCLUSION: Findings from this study suggest that intraoperative computer navigation will not require substantially increased operating times compared with standard surgical techniques. With prior surgeon training, approximately 8 operative cases are required to achieve proficiency in intraoperative computer navigation of the glenoid component.

Can Prophylactic Cables Stop Crack Propagation in Revision Arthroplasty: A Biomechanical Study.

BACKGROUND: Intraoperative femur fractures are a common complication of revision hip arthroplasty. This study examined the use of a prophylactic cable in stopping a crack from propagating beyond the cable. METHODS: Seventy sheep femora were prepared. A 5-mm vertical incision was performed. Using a force-controlled materials testing machine, a Wagner shaft was advanced until a crack occurred. Cracks were visualized with green ink. In the first part, the control group without any cable (n = 10) was compared with polyethylene (n = 15) and single CoCr cable (n = 15) groups. The cables were positioned 15 mm distal to the osteotomy. In the second part, three different CoCr configurations were compared, single-wrapped (n = 15), double-wrapped (n = 125), and two separate cables at 10 and 15 mm distal to the osteotomy (n = 15). RESULTS: The polyethylene cable stopped only 3 of 15 cracks (20%), whereas the CoCr cable stopped 11 of 15 cracks (73%) (P = .009). The force needed to initiate the crack between the different groups was not significant. Twelve (80%) of 15 cracks were stopped at the level of the cable with two separate CoCr cables and 15 (100%) of 15 cracks with a double-wrapped cable (P = .11). CONCLUSION: This study demonstrated that an elastic cable is not suitable for preventive cabling. The force required to form a crack is not improved with the use of a prophylactic cable placed 10-15 mm below the osteotomy. While the results on the different configurations were not conclusive, the double-wrapped cable was able to stop all cracks from progressing distally.

A review of methods to measure tendon dimensions.

Tendons are soft tissues of the musculoskeletal system that are designed to facilitate joint movement. Tendons exhibit a wide range of mechanical properties matched to their functions and, as a result, have been of interest to researchers for many decades. Dimensions are an important aspect of tendon properties.Change in the dimensions of tissues is often seen as a sign of injury and degeneration, as it may suggest inflammation or general disorder of the tissue. Dimensions are also important for determining the mechanical properties and behaviours of materials, particularly the stress, strain, and elastic modulus. This makes the dimensions significant in the context of a mechanical study of degenerated tendons. Additionally, tendon dimensions are useful in planning harvesting for tendon transfer and joint reconstruction purposes.Historically, many methods have been used in an attempt to accurately measure the dimensions of soft tissue, since improper measurement can lead to large errors in the calculated properties. These methods can be categorised as destructive (by approximation), contact, and non-contact and can be considered in terms of in vivo and ex vivo.

The Effect of Tibial Plateau Levelling Osteotomy on Stifle Extensor Mechanism Load: A Canine Ex Vivo Study.

OBJECTIVE: To evaluate the effect of tibial plateau levelling osteotomy on stifle extensor mechanism load in an ex vivo cruciate-intact canine cadaveric model. STUDY DESIGN: Ex vivo mechanical testing study. ANIMALS: Cadaveric canine pelvic limbs (n = 6). MATERIALS AND METHODS: A 21-mm tibial radial osteotomy was performed on pelvic limbs (n = 6) prior to being mounted into a load-bearing limb press. The proximal tibial segment was incrementally rotated until the anatomical tibial plateau angle had been rotated to at least 1°. The proportional change in stifle extensor mechanism load between the anatomical tibial plateau angle and the neutralized (∼6.5 degrees) and over-rotated (∼1°) tibial plateau angle was analysed using a one-sample t-test against a null hypothesis of no change. A p-value ≤0.05 was considered significant. RESULTS: There was no significant change in the stifle extensor mechanism load from the anatomical tibial plateau angle (308 N [261-355 N]) to the neutralized tibial plateau angle (313 N [254-372 N]; p =.81), or from the anatomical tibial plateau angle to the over-rotated tibial plateau angle (303 N [254-352 N; p = 0.67). CONCLUSION: Tibial plateau levelling osteotomy does not significantly alter stifle extensor mechanism load at either a neutralized or over-rotated tibial plateau angle in our cruciate-intact model.

Single-Piece Titanium Plate Cranioplasty Reconstruction of Complex Defects.

BACKGROUND: Different methods have been described for the reconstruction of cranial defects and orbital defects. The complex contouring between the orbital roof and frontal bone creates significant design challenges for prefabricated cranio-orbital reconstructions. In describing the first reported patient of combined skull and orbital roof reconstruction with a single-piece titanium plate cranioplasty, the authors present a new method of combined complex cranio-orbital reconstruction. METHODS: A 63-year-old lady presented with a large, right-sided frontal en-plaque meningioma involving the right orbit and sphenoid wing. Complete resection would require reconstruction of both the skull and the orbital roof. Surgical preplanning involved marking resection margins on a three-dimensional (3D) printed acrylonitrile-butadiene-styrene model. This margin was used to virtually resect the tumor and generate a repaired surface. A titanium plate was then fabricated using hydrostatic pressing into a 3D-printed mold and the orbital roof portion (a reentrant surface) was hand-finished. Lateral canthus and temporalis muscle suspension holes were prefabricated into the cranioplasty plate. RESULTS: The patient underwent hemicraniectomy and tumor resection guided by a custom-made 3D-printed cutting guide. The surgical defect was reconstructed with the prefabricated titanium plate achieving a good functional and cosmetic result. CONCLUSION: Single-piece titanium plate cranioplasty is an effective novel reconstruction method for complex cranio-orbital defects.

Structured white light scanning of rabbit Achilles tendon.

BACKGROUND: The cross-sectional area (CSA) of a material is used to calculate stress under load. The mechanical behaviour of soft tissue is of clinical interest in the management of injury; however, measuring CSA of soft tissue is challenging as samples are geometrically irregular and may deform during measurement. This study presents a simple method, using structured light scanning (SLS), to acquire a 3D model of rabbit Achilles tendon in vitro for measuring CSA of a tendon. METHOD: The Artec Spider™ 3D scanner uses structured light and stereophotogrammetry technologies to acquire shape data and reconstruct a 3D model of an object. In this study, the 3D scanner was integrated with a custom mechanical rig, permitting 360-degree acquisition of the morphology of six New Zealand White rabbit Achilles tendons. The reconstructed 3D model was then used to measure CSA of the tendon. SLS, together with callipers and micro-CT, was used to measure CSA of objects with a regular or complex shape, such as a drill flute and human cervical vertebra, for validating the accuracy and repeatability of the technique. RESULTS: CSA of six tendons was measured with a coefficient of variation of less than 2%. The mean CSA was 9.9±1.0mm2, comparable with those reported by other researchers. Scanning of phantoms demonstrated similar results to µCT. CONCLUSION: The technique developed in this study offers a simple and accurate method for effectively measuring CSA of soft tissue such as tendons. This allows for localised calculation of stress along the length, assisting in the understanding of the function, injury mechanisms and rehabilitation of tissue.

Voriconazole-associated soft tissue ossification: an undescribed cause of glenohumeral joint capsulitis.

Voriconazole-related periostitis has been increasingly described in the literature over the last several years as a recognizable disease entity, especially in lung transplant patients. This relationship should be considered when approaching immunosuppressed patients presenting with diffuse bone pain and imaging findings of periostitis. We present a case of voriconazole-associated periostitis, capsular and enthesial ossification and glenuhumeral capsulitis in a patient with a hematologic malignancy. To the authors' knowledge, soft tissue ossification associated with voriconazole has not been described in the radiology literature.

Evaluation of the C1-C2 articulation on MDCT in healthy children and young adults.

OBJECTIVE: We aimed to establish normal values on MDCT images for the atlantoaxial relationships including the atlantoaxial interval and lateral atlantodens interval (ADI) that could be used to detect atlantoaxial ligamentous injuries in adults and children. MATERIALS AND METHODS: One hundred seventy-eight healthy adult patients between 20 and 40 years old and 112 pediatric patients between 2 months and 10 years old underwent cervical spine MDCT with multiplanar reconstructions. The width of the joint space between the lateral mass of C1 and the lateral mass of C2 was measured at three equidistant points on both the left and right sides on coronal reformatted images to determine the atlantoaxial interval. The distance between the lateral surface of the dens and the medial surface of the lateral mass of C1 was measured in the coronal plane to determine the lateral ADI bilaterally. RESULTS: The upper limit of the normal range of values for the atlantoaxial interval in adults was 3.34 mm on the right and 3.39 mm on the left. The upper limit of normal for the lateral ADI was 4.67 mm on the right and 5.6 mm on the left. More than 95% of the pediatric population was found to have an atlantoaxial interval of less than 3.9 mm on either side, a right lateral ADI of less than 7.4 mm, and a left lateral ADI of less than 8.0 mm. CONCLUSION: We propose that the obtained normal values be considered as the upper limits of the normal range for the atlantoaxial interval in adult and pediatric populations on MDCT images.