Sulfonamide Per- and Polyfluoroalkyl Substances Can Impact Microorganisms Used in Aromatic Hydrocarbon and Trichloroethene Bioremediation.

Per- and polyfluoroalkyl substances (PFASs) from aqueous film forming foams (AFFFs) can hinder bioremediation of co-contaminants such as trichloroethene (TCE) and benzene, toluene, ethylbenzene, and xylene (BTEX). Anaerobic dechlorination can require bioaugmentation of Dehalococcoides, and for BTEX, oxygen is often sparged to stimulate in situ aerobic biodegradation. We tested PFAS inhibition to TCE and BTEX bioremediation by exposing an anaerobic TCE-dechlorinating coculture, an aerobic BTEX-degrading enrichment culture, and an anaerobic toluene-degrading enrichment culture to n-dimethyl perfluorohexane sulfonamido amine (AmPr-FHxSA), perfluorohexane sulfonamide (FHxSA), perfluorohexanesulfonic acid (PFHxS), or nonfluorinated surfactant sodium dodecyl sulfate (SDS). The anaerobic TCE-dechlorinating coculture was resistant to individual PFAS exposures but was inhibited by >1000× diluted AFFF. FHxSA and AmPr-FHxSA inhibited the aerobic BTEX-degrading enrichment. The anaerobic toluene-degrading enrichment was not inhibited by AFFF or individual PFASs. Increases in amino acids in the anaerobic TCE-dechlorinating coculture compared to the control indicated stress response, whereas the BTEX culture exhibited lower concentrations of all amino acids upon exposure to most surfactants (both fluorinated and nonfluorinated) compared to the control. These data suggest the main mechanisms of microbial toxicity are related to interactions with cell membrane synthesis as well as protein stress signaling.

PFAS Porewater concentrations in unsaturated soil: Field and laboratory comparisons inform on PFAS accumulation at air-water interfaces.

Poly- and perfluoroalkyl substance (PFAS) leaching from unsaturated soils impacted with aqueous film-forming foams (AFFFs) is an environmental challenge that remains difficult to measure and predict. Complicating measurements and predictions of this process is a lack of understanding between the PFAS concentrations measured in a collected environmental unsaturated soil sample, and the PFAS concentrations measured in the corresponding porewater using field-deployed lysimeters. The applicability of bench-scale batch testing to assess this relationship also remains uncertain. In this study, field-deployed porous cup suction lysimeters were used to measure PFAS porewater concentrations in unsaturated soils at 5 AFFF-impacted sites. Field-measured PFAS porewater concentrations were compared to those measured in porewater extracted in the laboratory from collected unsaturated soil cores, and from PFAS concentrations measured in the laboratory using batch soil slurries. Results showed that, despite several years since the last AFFF release at most of the test sites, precursors were abundant in 3 out of the 5 sites. Comparison of field lysimeter results to laboratory testing suggested that the local equilibrium assumption was valid for at least 3 of the sites and conditions of this study. Surprisingly, PFAS accumulation at the air-water interface was orders of magnitude less than expected at two of the test sites, suggesting potential gaps in the understanding of PFAS accumulation at the air-water interface at AFFF-impacted sites. Finally, results herein suggest that bench-scale testing on unsaturated soils can in some cases be used to inform on PFAS in situ porewater concentrations.

New PFASs Identified in AFFF Impacted Groundwater by Passive Sampling and Nontarget Analysis.

Monitoring contamination from per- and polyfluoroalkyl substances (PFASs) in water systems impacted by aqueous film-forming foams (AFFFs) typically addresses a few known PFAS groups. Given the diversity of PFASs present in AFFFs, current analytical approaches do not comprehensively address the range of PFASs present in these systems. A suspect-screening and nontarget analysis (NTA) approach was developed and applied to identify novel PFASs in groundwater samples contaminated from historic AFFF use. A total of 88 PFASs were identified in both passive samplers and grab samples, and these were dominated by sulfonate derivatives and sulfonamide-derived precursors. Several ultrashort-chain (USC) PFASs (≤C3) were detected, 11 reported for the first time in Australian groundwater. Several transformation products were identified, including perfluoroalkane sulfonamides (FASAs) and perfluoroalkane sulfinates (PFASis). Two new PFASs were reported (((perfluorohexyl)sulfonyl)sulfamic acid; m/z 477.9068 and (E)-1,1,2,2,3,3,4,5,6,7,8,8,8-tridecafluorooct-6-ene-1-sulfonic acid; m/z 424.9482). This study highlights that several PFASs are overlooked using standard target analysis, and therefore, the potential risk from all PFASs present is likely to be underestimated.

Quantification of long-chain, short-chain, and ultrashort-chain liquid chromatography-amenable PFASs in water: Evaluation of approaches and tradeoffs for AFFF-impacted water.

The widespread use of aqueous film-forming foam (AFFF) for firefighting and firefighter training has led to extensive per- and polyfluoroalkyl substance (PFAS) contamination in the environment. Challenges remain in the analytical determination of PFASs via liquid chromatography-mass spectrometry (LC-MS), particularly when attempting to include ultrashort-chain perfluoroalkyl acids (PFAAs) and longer-chain anionic and zwitterionic PFASs in a single direct injection. In this study, we assessed the performance of three analytical LC columns (C18, JJ, and Acclaim columns) to separate targeted and suspect PFASs in AFFF-impacted water samples collected from five sites. The C18 column failed to retain ultrashort-chain PFAAs while the JJ and Acclaim columns were not suitable for hydrophobic PFASs. Ultrashort-chain PFAAs were detected at three sites and comprised 1.6-18% of the total perfluoroalkyl carboxylic and sulfonic acids. Semi-quantified concentrations of suspect PFASs comprised 0.70-13% of the total PFASs. When attempting to capture the entirety of the PFAS mass in a water sample, the C18 column captured the broadest suite of suspect PFASs, while the JJ column quantified the most total PFAS mass. Results of this study highlight the importance and tradeoffs of LC column choice to comprehensively determine the composition of PFASs and their concentrations in AFFF-impacted water samples.

Effect-Directed Analysis Based on Transthyretin Binding Activity of Per- and Polyfluoroalkyl Substances in a Contaminated Sediment Extract.

Only a fraction of the total number of per- and polyfluoroalkyl substances (PFAS) are monitored on a routine basis using targeted chemical analyses. We report on an approach toward identifying bioactive substances in environmental samples using effect-directed analysis by combining toxicity testing, targeted chemical analyses, and suspect screening. PFAS compete with the thyroid hormone thyroxin (T4 ) for binding to its distributor protein transthyretin (TTR). Therefore, a TTR-binding bioassay was used to prioritize unknown features for chemical identification in a PFAS-contaminated sediment sample collected downstream of a factory producing PFAS-coated paper. First, the TTR-binding potencies of 31 analytical PFAS standards were determined. Potencies varied between PFAS depending on carbon chain length, functional group, and, for precursors to perfluoroalkyl sulfonic acids (PFSA), the size or number of atoms in the group(s) attached to the nitrogen. The most potent PFAS were the seven- and eight-carbon PFSA, perfluoroheptane sulfonic acid (PFHpS) and perfluorooctane sulfonic acid (PFOS), and the eight-carbon perfluoroalkyl carboxylic acid (PFCA), perfluorooctanoic acid (PFOA), which showed approximately four- and five-times weaker potencies, respectively, compared with the native ligand T4 . For some of the other PFAS tested, TTR-binding potencies were weak or not observed at all. For the environmental sediment sample, not all of the bioactivity observed in the TTR-binding assay could be assigned to the PFAS quantified using targeted chemical analyses. Therefore, suspect screening was applied to the retention times corresponding to observed TTR binding, and five candidates were identified. Targeted analyses showed that the sediment was dominated by the di-substituted phosphate ester of N-ethyl perfluorooctane sulfonamido ethanol (SAmPAP diester), whereas it was not bioactive in the assay. SAmPAP diester has the potential for (bio)transformation into smaller PFAS, including PFOS. Therefore, when it comes to TTR binding, the hazard associated with this substance is likely through (bio)transformation into more potent transformation products. Environ Toxicol Chem 2024;43:245-258. © 2023 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.

Hydrothermal Alkaline Treatment (HALT) of Foam Fractionation Concentrate Derived from PFAS-Contaminated Groundwater.

While foam fractionation (FF) process has emerged as a promising technology for removal of per- and polyfluoroalkyl substances (PFASs) from contaminated groundwater, management of the resulting foam concentrates with elevated concentrations of PFASs (e.g., >1 g/L) remains a challenge. Here, we applied hydrothermal alkaline treatment (HALT) to two foam concentrates derived from FF field demonstration projects that treated aqueous film-forming foam (AFFF)-impacted groundwater. Results showed >90% degradation and defluorination within 90 min of treatment (350 °C, 1 M NaOH) of all 62 PFASs (including cations, anions, and zwitterions) identified in foam concentrates. Observed rate constants for degradation of individual perfluoroalkyl sulfonates (PFSAs, CnF2n+1-SO3-), the most recalcitrant class of PFASs, in both foam concentrates were similar to values measured previously in other aqueous matrices, indicating that elevated initial PFAS concentrations (e.g., PFHxSinit = 0.55 g/L), dissolved organic carbon (DOC; up to 4.5 g/L), and salt levels (e.g., up to 325 mg/L chloride) do not significantly affect PFAS reaction kinetics. DOC was partially mineralized by treatment, but a fraction (∼15%) was recalcitrant. Spectroscopic characterization revealed molecular features of the HALT-recalcitrant DOC fraction, and nontarget high-resolution mass spectrometry tentatively identified 129 nonfluorinated HALT-recalcitrant molecules. Analysis of process energy requirements shows that treating PFAS-contaminated foam concentrates with HALT would add minimally (<5%) to the overall energy requirements of an integrated FF-HALT treatment train.

Predicting PFAS and Hydrophilic Trace Organic Contaminant Transport in Black Carbon-Amended Engineered Media Filters for Improved Stormwater Runoff Treatment.

Improved stormwater treatment is needed to prevent toxic and mobile contaminant transport into receiving waters and allow beneficial use of stormwater runoff. In particular, safe capture of stormwater runoff to augment drinking water supplies is contingent upon removing dissolved trace organic contaminants (TrOCs) not captured by conventional stormwater control measures. This study builds upon a prior laboratory-based column study investigating biochar and regenerated activated carbon (RAC) amendment for removing hydrophilic trace organic contaminants (HiTrOCs) and poly- and perfluoroalkyl substances (PFASs) from stormwater runoff. A robust contaminant transport model framework incorporating time-dependent flow and influent concentration is developed and validated to predict HiTrOC and PFAS transport in biochar- and RAC-amended stormwater filters. Specifically, parameters fit using a sorption-retarded intraparticle pore diffusion transport model were validated using data further along the depth of the column and compared to equilibrium batch isotherms. The transport model and fitted parameters were then used to estimate the lifetime of a hypothetical stormwater filter in Seal Beach, CA, to be 35 ± 6 years for biochar- and 51 ± 17 years for RAC-amended filters, under ideal conditions with no filter clogging. This work offers insights on the kinetics of HiTrOC and PFAS transport within biochar and RAC filters and on the impact of filter design on contaminant removal performance and longevity.

Target and Suspect Screening Integrated with Machine Learning to Discover Per- and Polyfluoroalkyl Substance Source Fingerprints.

This study elucidates per- and polyfluoroalkyl substance (PFAS) fingerprints for specific PFAS source types. Ninety-two samples were collected from aqueous film-forming foam impacted groundwater (AFFF-GW), landfill leachate, biosolids leachate, municipal wastewater treatment plant effluent (WWTP), and wastewater effluent from the pulp and paper and power generation industries. High-resolution mass spectrometry operated with electrospray ionization in negative mode was used to quantify up to 50 target PFASs and screen and semi-quantify up to 2,266 suspect PFASs in each sample. Machine learning classifiers were used to identify PFASs that were diagnostic of each source type. Four C5-C7 perfluoroalkyl acids and one suspect PFAS (trihydrogen-substituted fluoroethernonanoic acid) were diagnostic of AFFF-GW. Two target PFASs (5:3 and 6:2 fluorotelomer carboxylic acids) and two suspect PFASs (4:2 fluorotelomer-thia-acetic acid and N-methylperfluoropropane sulfonamido acetic acid) were diagnostic of landfill leachate. Biosolids leachates were best classified along with landfill leachates and N-methyl and N-ethyl perfluorooctane sulfonamido acetic acid assisted in that classification. WWTP, pulp and paper, and power generation samples contained few target PFASs, but fipronil (a fluorinated insecticide) was diagnostic of WWTP samples. Our results provide PFAS fingerprints for known sources and identify target and suspect PFASs that can be used for source allocation.

Hydroxyl Radical Transformations of Perfluoroalkyl Acid (PFAA) Precursors in Aqueous Film Forming Foams (AFFFs).

Historical releases of aqueous film forming foam (AFFF) are significant sources of poly- and perfluoroalkyl substances (PFASs), including perfluoroalkyl acids (PFAAs) and their precursors, to the environment. While several studies have focused on microbial biotransformation of polyfluorinated precursors to PFAAs, the role of abiotic transformations at AFFF-impacted sites is less clear. Herein, we use photochemically generated hydroxyl radical to demonstrate that environmentally relevant concentrations of hydroxyl radical (•OH) can play a significant role in these transformations. High-resolution mass spectrometry (HRMS) was used to perform targeted analysis, suspect screening, and nontargeted analyses, which were used to identify the major products of AFFF-derived PFASs as perfluorocarboxylic acids, though several potentially semi-stable intermediates were also observed. Using competition kinetics in a UV/H2O2 system, hydroxyl radical rate constants (kOH) for 24 AFFF-derived polyfluoroalkyl precursors were measured to be 0.28 to 3.4 × 109 M-1 s-1. Differences in kOH were observed for compounds with differing headgroups and perfluoroalkyl chain lengths. Also, differences in kOH measured for the only relevant precursor standard available, n-[3-propyl]tridecafluorohexanesulphonamide (AmPr-FHxSA), as compared to AmPr-FHxSA present in AFFF suggest that intermolecular associations in the AFFF matrix may affect kOH. Considering environmentally relevant [•OH]ss, polyfluoroalkyl precursors are expected to exhibit half-lives of ∼8 days in sunlit surface waters and possibly as short as ∼2 h during oxygenation of Fe(II)-rich subsurface systems.

Influence of Carbonate Speciation on Hydrated Electron Treatment Processes.

Advanced reduction processes (ARPs) that generate hydrated electrons (eaq-; e.g., UV-sulfite) have emerged as a promising remediation technology for recalcitrant water contaminants, including per- and polyfluoroalkyl substances (PFASs). The effectiveness of ARPs in different natural water matrices is determined, in large part, by the presence of non-target water constituents that act to quench eaq- or shield incoming UV photons from the applied photosensitizer. This study examined the pH-dependent quenching of eaq- by ubiquitous dissolved carbonate species (H2CO3*, HCO3-, and CO32-) and quantified the relative importance of carbonate species to other abundant quenching agents (e.g., H2O, H+, HSO3-, and O2(aq)) during ARP applications. Analysis of laser flash photolysis kinetic data in relation to pH-dependent carbonate acid-base speciation yields species-specific bimolecular rate constants for eaq- quenching by H2CO3*, HCO3-, and CO32- (kH2CO3* = 2.23 ± 0.42 × 109 M-1 s-1, kHCO3- = 2.18 ± 0.73 × 106 M-1 s-1, and kCO32- = 1.05 ± 0.61 × 105 M-1 s-1), with quenching dominated by H2CO3* (which includes both CO2(aq) and H2CO3) at moderately alkaline pH conditions despite it being the minor species. Attempts to apply previously reported rate constants for eaq- quenching by CO2(aq), measured in acidic solutions equilibrated with CO2(g), overpredict quenching observed in this study at higher pH conditions typical of ARP applications. Moreover, kinetic simulations reveal that pH-dependent trends reported for UV-sulfite ARPs that have often been attributed to eaq- quenching by varying [H+] can instead be ascribed to variable acid-base speciation of dissolved carbonate and the sulfite sensitizer.

Sorption affinity and mechanisms of per-and polyfluoroalkyl substances (PFASs) with commercial sorbents: Implications for passive sampling.

Effective monitoring tools, including passive samplers, are essential for the wide range of per- and polyfluoroalkyl substances (PFASs) in aquatic matrices. However, knowledge of the extent and mechanisms of PFASs sorption with sorbents in a passive sampling context is limited. To address this, sorption behavior of 45 anionic, neutral and zwitterionic PFASs ranging in perfluorocarbon chain length (C3-C16) and functional groups with 11 different commercial sorbents (cross-linked ß-cyclodextrin polymers, activated carbon, anion exchange (AE), cation exchange, hydrophilic-lipophilic balanced (HLB) and non-polar) was investigated. A broad range of equilibrium sorbent-MilliQ water (MQ) distribution coefficients (Kd) were observed (10-1.95 to 108.30 mL g-1). Similar sorbent types (e.g., various AE and HLB sorbents) exhibited very different sorption behavior, likely due to their different polymeric structures and relative importance of sorbate/sorbent interactions other than coulombic interactions. HLB and AE with hydroxyl functionalities are most effective for sampling of the full suite of PFASs. Reduced sorptive affinity was observed in the presence of matrix co-constituents in wastewater influent for most PFASs. HLB had the smallest reduction in log Kd in wastewater suggesting that these sorbents are appropriate for applications in complex matrices. Sufficient sorbent capacity was observed for linear uptake of many target analytes which facilitates passive sampling.

Estimating historical exposure to perfluoroalkyl acids in Security, Fountain, and Widefield Colorado: use of water-infrastructure blending and toxicokinetic models.

Drinking water can be a major source of poly- and perfluoroalkyl substance (PFAS) exposure for humans. The lack of historic data on PFAS drinking-water concentrations and consumption patterns are a limiting factor for developing estimates of past exposure. Here, in contribution to a community-scale PFAS health effects study near fire training facilities that contaminated a local aquifer with PFASs, we present a novel water-infrastructure, mass-balance mixing model coupled to a non-steady state, single-compartment toxicokinetic model that used Monte Carlo simulations to estimate the start of PFAS exposure in drinking water for individuals within three PFAS-impacted communities in El Paso County, Colorado. Our modeling focused on perfluorohexane sulfonic acid (PFHxS) because median serum PFHxS concentrations in a sample of local residents (n = 213) were twelve times the median observed in the U.S. National Health and Nutrition Examination Survey (2015-2016). Modeling results for study participants were grouped according to their community of residence, revealing a median start of exposure for the town of Fountain of 1998 (25-75% interquartile range [IQR], 1992 to 2010), 2006 (IQR 1995 to 2012) for Security, and 2009 (IQR 1996-2012) for Widefield. Based on the towns' locations relative to an identified hydraulically upgradient PFAS source, the modeled exposure sequencing does not completely align with this conceptual flow model, implying the presence of an additional PFAS source for the groundwater between Widefield and Fountain.

Self-Collection Blood Test for PFASs: Comparing Volumetric Microsamplers with a Traditional Serum Approach.

A remote sampling approach was developed at Eurofins for quantifying per- and polyfluoroalkyl substances (PFASs) in whole blood samples collected using volumetric absorptive microsamplers (VAMSs), which allow for self-collection of blood using a finger prick. This study compares PFAS exposure measured by self-collection of blood using VAMSs to the standard venous serum approach. Blood samples were collected from participants (n = 53) in a community with prior PFAS drinking water contamination using a venous blood draw as well as participant self-collection using VAMSs. Whole blood from the venous tubes was also loaded onto VAMSs to compare differences in capillary vs venous whole blood PFAS levels. Samples were quantified for PFASs using liquid chromatography tandem mass spectrometry and online solid-phase extraction. PFAS levels in serum were highly correlated with measurements in capillary VAMSs (r ≥ 0.91 and p < 0.05). Serum PFAS levels were generally twofold higher than whole blood, reflecting expected differences in their composition. Of interest, FOSA was detected in whole blood (both venous and capillary VAMSs) but not in serum. Overall, these findings indicate that VAMSs are useful self-collection tools for assessing elevated human exposure to PFASs.

Physical and chemical properties of carbon-based sorbents that affect the removal of per- and polyfluoroalkyl substances from solution and soil.

Removal of per- and polyfluoroalkyl substances (PFASs) from water or their immobilization in soil using carbon-based sorbents is one of the cost-effective techniques. Considering the variety of carbon-based sorbents, identifying the key sorbent properties responsible for PFASs removal from solution or immobilization in the soil can assist in the selection of the best sorbents for management of contaminated sites. This study evaluated the performance of 28 carbon-based sorbents including granular and powdered activated carbon (GAC and PAC), mixed mode carbon mineral material, biochars, and graphene-based materials (GNBs). The sorbents were characterized for a range of physical and chemical properties. PFASs' sorption from an AFFF-spiked solution was examined via a batch experiment, while their ability to immobilize PFASs in soil was tested following mixing, incubation and extraction using the Australian Standard Leaching Procedure. Both soil and solution were treated with 1 % w/w sorbents. Comparing different carbon-based materials, PAC, mixed mode carbon mineral material and GAC were the most effective in sorbing PFASs in both solution and soil. Among the different physical characteristics measured, the sorption of long-chain and more hydrophobic PFASs in both soil and solution was best correlated with sorbent surface area measured using methylene blue, which highlights the importance of mesopores in PFASs sorption. Iodine number was found to be a better indicator of the sorption of short-chain and more hydrophilic PFASs from solution but was found to be poorly correlated with PFASs immobilization in soil for activated carbons. Sorbents with a net positive charge performed better than those with a net negative charge, or no net charge. This study showed that surface area measured by methylene blue and surface charge are the best indicators of sorbent performance with respect to sorption/reducing leaching of PFASs. These properties may be helpful in selecting sorbents for PFASs remediation of soils/waters.

Predicting Concentration- and Ionic-Strength-Dependent Air-Water Interfacial Partitioning Parameters of PFASs Using Quantitative Structure-Property Relationships (QSPRs).

Air-water interfacial retention of poly- and perfluoroalkyl substances (PFASs) is increasingly recognized as an important environmental process. Herein, column transport experiments were used to measure air-water interfacial partitioning values for several perfluoroalkyl ethers and for PFASs derived from aqueous film-forming foam, while batch experiments were used to determine equilibrium Kia data for compounds exhibiting evidence of rate-limited partitioning. Experimental results suggest a Freundlich isotherm best describes PFAS air-water partitioning at environmentally relevant concentrations (101-106 ng/L). A multiparameter regression analysis for Kia prediction was performed for the 15 PFASs for which equilibrium Kia values were determined, assessing 246 possible combinations of 8 physicochemical and system properties. Quantitative structure-property relationships (QSPRs) based on three to four parameters provided predictions of high accuracy without model overparameterization. Two QSPRs (R2 values of 0.92 and 0.83) were developed using an assumed average Freundlich n value of 0.65 and validated across a range of relevant concentrations for perfluorooctane sulfonate (PFOS), perfluorooctanoate (PFOA), and hexafluoropropylene oxide-dimer acid (i.e., GenX). A mass action model was further modified to account for the changing ionic strength on PFAS air-water interfacial sorption. The final result was two distinct QSPRs for estimating PFAS air-water interfacial partitioning across a range of aqueous concentrations and ionic strengths.

Black Carbon-Amended Engineered Media Filters for Improved Treatment of Stormwater Runoff.

Urban stormwater runoff is a significant driver of surface water quality impairment. Recently, attention has been drawn to potential beneficial use of urban stormwater runoff, including augmenting drinking water supply in water-stressed areas. However, beneficial use relies on improved treatment of stormwater runoff to remove mobile dissolved metals and trace organic contaminants (TrOCs). This study assesses six engineered media mixtures consisting of sand, zeolite, high-temperature gasification biochar, and regenerated activated carbon (RAC) for removing a suite of co-contaminants comprising five metals, three herbicides, four pesticides, a corrosion inhibitor, six per- and polyfluoroalkyl substances (PFASs), five polychlorinated biphenyls (PCBs), and six polycyclic aromatic hydrocarbons (PAHs). This long-term laboratory-scale column study uses a novel approach to generate reproducible synthetic stormwater that incorporates catch basin material and straw-derived dissolved organic carbon. Higher flow conditions (20 cm hr-1), larger sized media (0.42-1.68 mm), and downflow configuration with outlet control increase the relevance of this study to better enable implementation in the field. Biochar- and RAC-amended engineered media filters removed nearly all of the TrOCs in the effluent over the course of three months of continuous flow (480 empty bed volumes), while sample ports spaced at 25% and 50% along the column depth provide windows to observe contaminant transport. Biochar provided greater benefit to TrOC removal than RAC on a mass basis. This study used relatively high concentrations of contaminants and low biochar and RAC content to observe contaminant transport. Performance in the field is likely to be significantly better with higher biochar- and RAC-content filters and lower ambient stormwater contaminant concentrations. This study provides proof-of-concept for biochar- and RAC-amended engineered media filters operated at a flow rate of 20 cm hr-1 for removing dissolved TrOCs and metals and offers insights on the performance of biochar and RAC for improved stormwater treatment and field trials.

Leaching of Perfluoroalkyl Acids during Unsaturated Zone Flushing at a Field Site Impacted with Aqueous Film Forming Foam.

While several studies have focused on perfluoroalkyl acid (PFAA) leaching from soils, field studies evaluating the relationship between PFAA mass removal and porewater concentrations as the PFAA source becomes depleted are lacking. Herein, in situ water flushing was performed at a site historically impacted with AFFF to accelerate the leaching of PFAAs from unsaturated soils in a highly characterized field test cell. Porous cup suction lysimeters were used to assess the changes in PFAA porewater concentrations as a function of PFAA mass removal from the unsaturated soils, where flushing was intermittently paused to determine ambient PFAA porewater concentrations. Results showed that the fractional decreases in PFAA porewater concentrations during flushing exceeded the fractional decrease in PFAA mass removal from the soil. PFOS porewater concentrations decrease by 76% (with negligible rebound) compared to only a 7.4% decrease in overall PFOS mass removed from the unsaturated zone. Overall, the results observed herein suggest that, when considering soil impacts to groundwater, less stringent soil cleanup criteria than those that consider an equivalent relationship between mass removal and mass discharge may be appropriate. In addition, remedial approaches that remove only a modest fraction of the PFAA soil mass may be protective of underlying groundwater, particularly for perfluorinated sulfonates with at least six carbons.