Feasibility study of production of radioactive carbon black or carbon nanotubes in cyclotron facilities for nanobioscience applications.

A feasibility study regarding the production of radioactive carbon black and nanotubes has been performed by proton beam irradiation. Experimental and theoretical excitation functions of the nuclear reaction (nat)C(p,x)(7)Be in the proton energy range 24-38 MeV are reported, with an acceptable agreement. We have demonstrated that sufficient activities of (7)Be radioisotope can be produced in carbon black and nanotube that would facilitate studies of their possible impact on human and environment.

Radiolabelling of engineered nanoparticles for in vitro and in vivo tracing applications using cyclotron accelerators.

We present in this article an outline of some cyclotron-based irradiation techniques that can be used to directly radiolabel industrially manufactured nanoparticles, as well as two techniques for synthesis of labelled nanoparticles using cyclotron-generated radioactive precursor materials. These radiolabelled nanoparticles are suitable for a range of different in vitro and in vivo tracing studies of relevance to the field of nanotoxicology. A basic overview is given of the relevant physics of nuclear reactions regarding both ion-beam and neutron production of radioisotopes. The various issues that determine the practicality and usefulness of the different methods are discussed, including radioisotope yield, nuclear reaction kinetics, radiation and thermal damage, and radiolabel stability. Experimental details are presented regarding several techniques applied in our laboratories, including direct light-ion activation of dry nanoparticle samples, neutron activation of nanoparticles and suspensions using an ion-beam driven activator, spark-ignition generation of nanoparticle aerosols using activated electrode materials, and radiochemical synthesis of nanoparticles using cyclotron-produced isotopes. The application of these techniques is illustrated through short descriptions of some selected results thus far achieved. It is shown that these cyclotron-based methods offer a very useful range of options for nanoparticle radiolabelling despite some experimental difficulties associated with their application. For direct nanoparticle radiolabelling, if care is taken in choosing the experimental conditions applied, useful activity levels can be achieved in a wide range of nanoparticle types, without causing substantial thermal or radiation damage to the nanoparticle structure. Nanoparticle synthesis using radioactive precursors presents a different set of issues and offers a complementary and equally valid approach when laboratory generation of the nanoparticles is acceptable for the proposed studies, and where an appropriate radiolabel can be incorporated into the nanoparticles during synthesis.

Cyclotron production of radioactive CeO(2) nanoparticles and their application for in vitro uptake studies.

Nowadays, a wide variety of nanoparticles (NPs) are applied in different fields such as medical science and industry. Due to their large commercial volume, the OECD Working Party on Manufactured Nanomaterials (NMs) has proposed to study a set of 14 nanomaterials, one of which being cerium oxide (CeO(2)). In particular, CeO(2) based NPs are widely used in automotive industry, healthcare, and cosmetics. In this paper, we propose a method for the production of radioactive CeO(2) NPs.We demonstrate that they maintain the same physicochemical characteristics as the "cold" ones in terms of size distribution and Zeta potential; we develop a new protocol to assess their cellular interaction in immortalized mouse fibroblast cell line Balb/3T3, a model for the study of basal cytotoxicity and carcinogenic potential induced by chemicals and in the present case by NPs. Experimental result of this work, which shows a quasi-linear concentration-uptake response of cells, can be useful as a reference dose-uptake curve for explaining effects following biological uptake after exposure to CeO(2) NPs.

Measurement techniques for tracer kinetic studies with stable isotopes of zirconium.

Biokinetic models are used in radiation protection to assess internal radiation doses. Experiments with stable isotopes as tracers can be performed to obtain characteristic parameters of these models. Two methods for the measurement of zirconium isotopes in human biological samples are presented--thermal ionisation mass spectrometry (TIMS) and proton nuclear activation analysis (PNA). Descriptions include sample preparation, operating conditions, relative uncertainties and method detection limits as well as important properties of both methods.

[Allergic reaction to components of bone cement after total knee arthroplasty]. / Allergie auf Knochenzementbestandteile nach Knieendoprothesenimplantation.

There are many reports about allergic reactions in association with total hip or knee arthroplasty. While most studies focus on allergic reactions to metallic components, only few reports exist about reactions to bone cement or its ingredients. We report about a patient who developed eczema at the knee and the lower leg one year after cemented TKR. Patch testing showed as potential causes contact allergic reactions to nickel and benzoylperoxide, an ingredient of the here used bone cement. The local and temporal association between onset of eczema and knee arthroplasty suggests a causal link. Benzoylperoxide as potential contact allergen in bone cement is so far almost neglected. The development of extended testing procedures and data collection should provide further information and better care of these patients. The development of special bone cements for patients with allergic diathesis is requested.

Cyclotron production of 64Cu by deuteron irradiation of 64Zn.

The short-lived (12.7h half-life) (64)Cu radioisotope is both a beta(+) and a beta(-) emitter. This property makes (64)Cu a promising candidate for novel medical applications, since it can be used simultaneously for therapeutic application of radiolabelled biomolecules and for diagnosis with PET. Following previous work on (64)Cu production by deuteron irradiation of natural zinc, we report here the production of this radioisotope by deuteron irradiation of enriched (64)Zn. In addition, yields of other radioisotopes such as (61)Cu, (67)Cu, (65)Zn, (69m)Zn, (66)Ga and (67)Ga, which were co-produced in this process, were also measured. The evaporation code ALICE-91 and the transport code SRIM 2003 were used to determine the excitation functions and the stopping power, respectively. All the nuclear reactions yielding the above-mentioned radioisotopes were taken into account in the calculations both for the natural and enriched Zn targets. The experimental and calculated yields were shown to be in reasonable agreement. The work was carried out at the Scanditronix MC-40 Cyclotron of the Institute for Health and Consumer Protection of the Joint Research Centre of the European Commission (Ispra site, Italy). The irradiations were carried out with 19.5 MeV deuterons, the maximum deuteron energy obtainable with the MC-40 cyclotron.

Tribological characterization of surface-treated commercially pure titanium for femoral heads in total hip replacement: a feasibility study.

Most noncemented total hip replacements combine a titanium alloy stem, a CoCrMo femoral head and an ultra-high molecular weight polyethylene (UHMWPE) acetabular cup. In spite of its nickel content of up to 1% and the resulting biocompatibility issues in some clinical situations, the higher cost and some difficulties in machining, CoCrMo alloy is preferred to titanium alloys thanks to its outstanding tribological properties, higher hardness and elastic modulus. Nowadays most of the heads of hip prostheses use CoCrMo as bearing material. The present study investigates the effect of various surface treatments and combinations of treatments, such as electrochemical oxidation (anodization), laser surface melting and barrel polishing, on the tribological properties of commercially pure grade 2 titanium. The aim of the study was to characterize surface treatments capable of improving the tribological properties of titanium surface to the same extent as CoCrMo. The tribological properties were characterized by multidirectional pin-on-flat screening wear tests, using UHMWPE pins as bearing surface. The experiments showed the possibility of improving the wear resistance of titanium to the degree of CoCrMo. Although further efforts will be required to optimize the treatments studied, the results are encouraging enough to warrant pursuing this direction of investigation.

[Residual particle free surfaces after shot peening in modular hip arthroplasty are feasible]. / Restpartikelfreie Oberflächen nach Stahlkugelstrahlen modularer Hüftendoprothesen sind erreichbar.

INTRODUCTION: Shot peening with steel balls is used for introduction of compressive stress in the production of morse taper junctions of modular hip endoprostheses. After this procedure, significant contamination with residual particles can be detected, which may lead to increased corrosion and third body wear. Additionally, the European norm EN 12010 requires surfaces free of residual particles. The aim of this study is to evaluate the effects of several cleaning procedures with regard to complying with EN 12010. MATERIAL AND METHOD: The surfaces of 12 Ti6Al7Nb rods with a diameter of 15 mm was shot peened with steel balls (GS VERA, Fa. Würth, Bad Friedrichshall, Germany). A field emission scanning electron microscopy (SEM, LEO 1525) was used for the detection of residual particles on the surface of the rods with a backscattered electron detector. After SEM examination, one sample each was cleaned using shot peening with sugar or dry ice and 10 rods using a pH dependent cleaning procedure. After these cleaning procedures, the samples were again analysed with the SEM for residual particle contamination. RESULTS: The surface of all rods showed a considerable contamination with steel particles after shot-peening with steel balls. After the cleaning procedure with dry ice or sugar steel contamination was lower, however, only the pH dependent cleaning procedure was able to achieve surfaces free of residual particles. DISCUSSION: For smooth shot-peened surfaces in modular hip arthroplasty Euro Norm EN 12010 can be fulfilled using shot peening with steel balls followed by a pH dependent cleaning procedure.

[Metallurgical differentiation of cobalt-chromium alloys for implants]. / Metallkundliche Differenzierung von Kobalt-Chrom-Legierungen für Implantate.

BACKGROUND: Cobalt Chromium alloys are used in cemented total hip or knee arthroplasty as well as in metal-on-metal bearings in total hip arthroplasty. An increasing number of publications report about (allergic) reactions to wear particles of Cobalt Chromium alloys. Reactions to nickel are more frequent in comparison to Cobalt or Chromium particles. It is well known that different kinds of Cobalt Chromium alloys contain different amounts of alloying elements; nevertheless. The aim of the current work was to compare the different Cobalt Chromium alloys according to ASTM F or ISO standards in respect to the different alloying elements. MATERIAL AND METHODS: Co28Cr6Mo casting alloys according to ASTM F 75 or ISO 5832-4 as well as forging alloy types according to ASTM F 799 and ISO 5832 such as Co20Cr15W10Ni, Co35Ni20Cr, Fe40Co20Cr10Ni, Co20Cr20Ni, and Co28Cr6Mo were analyzed in respect to their element content of Co, Cr, Ni, Mo, Fe, W, and Mn. RESULTS: In 1935 the Cobalt based alloy "Vitallium" Co30Cr5Mo basically used in the aircraft industry was introduced into medicine. The chemical composition of this alloy based on Cobalt showed 30 wt.% Chromium and 5 wt.% Molybdenum. The differentiation using alloy names showed no Nickel information in single alloy names. CONCLUSION: The information given about different alloys can lead to an unprecise evaluation of histopathological findings in respect to alloys or alloying constituents. Therefore, implant manufacturers should give the exact information about the alloys used and adhere to European law, Euronorm 93/42/EWG.

Optimisation study of alpha-cyclotron production of At-211/Po-211g for high-LET metabolic radiotherapy purposes.

The production of no-carrier-added (NCA) alpha-emitter (211)At/(211g)Po radionuclides for high-LET targeted radiotherapy and immunoradiotherapy, through the (209)Bi(alpha,2n) reaction, together with the required wet radiochemistry and radioanalytical quality controls carried out at LASA is described, through dedicated irradiation experiments at the MC-40 cyclotron of JRC-Ispra. The amount of both the gamma-emitter (210)At and its long half-lived alpha-emitting daughter (210)Po is optimised and minimised by appropriate choice of energy and energy loss of alpha particle beam. The measured excitation functions for production of the main radioisotopic impurity (210)At-->(210)Po are compared with theoretical predictions from model calculations performed at ENEA.

[The use of a thermomechanical cleaning procedure for removal of residual particles of corund blasted or glass bead peened implants in total hip arthoplasty]. / Die Anwendung eines thermomechanischen Reinigungsverfahrens zur Entfernung von Restpartikeln auf Oberflächen von korund- bzw. glasperlengestrahlten Hüftgelenkimplantaten.

INTRODUCTION: Shot peening and grit blasting techniques are used to modify surfaces of hip endoprostheses. Alumina blasting techniques using highly pure corund (Al (2)O (3)) particles create a rough surface of Titanium implants to achieve a better osteointegration in cementless total hip arthroplasty. An increasing number of publications in maxillo-facial-surgery and orthopedic surgery show that there is a significant contamination with remnants on corund blasted surfaces. To our knowledge no previous study analysed the effects of cleaning procedures of hip endoprostheses in respect to glass beads and Al (2)O (3) remnants. MATERIAL AND METHOD: The surface of the flexible anisotropic Vector cup and the stiff modular MRP-Titan stem (one implant each) were analysed with respect to Al (2)O (3) or glass particles before and after the cleaning procedure. The implants were cleaned using an ultrasound bath for 10 or 20 minutes under nitrogen cooling or simple ultrasound bath with water. A field emission scanning electron microscopy (LEO 1525) was used for the detection of the particles on the implant surface with a backscattered electron detector. The proportion of the surface covered with particles was determined with an imaging analyze software (analySIS, Soft Imaging System GmbH). RESULTS: A reduction of corund particles on the surface of the flexible anisotropic Vector cup of up to 5.2 % (from 40.0 % to 34.8 %) after 10 minutes nitrogen cooling was achieved. A reduction of corund particles on the surface of the stiff MRP-Titan stem of up to 2.2 % (from 38.8 % to 36.6 %) was observed after 20 minutes of non cooled ultrasound bath whereas a reduction up to 3.2 % (from 25.8 % to 22.6 %) of glass particles after 10 minutes of nitrogen cooled ultrasound bath was detected. CONCLUSION: With the cleaning procedure tested only incomplete removal of just the small glass and Al (2)O (3) particles is possible. Further research is needed to reduce or even avoid residual particles in total hip arthoplasty.

[Allergic potential of titanium implants]. / Das Allergiepotenzial von Implantatwerkstoffen auf Titanbasis.

AIM: The aim of this investigation is to evaluate the allergic potential of titanium and titanium alloys for surgical implant applications. MATERIALS AND METHODS: Discs cut from rods supplied by five different titanium suppliers in several diameters were investigated. The samples were cp-Titanium as well as Ti6Al4 V and Ti6Al7Nb, 6 mm thick with a diameter of between 6 and 60 mm. The material was checked by optical spectral analysis. RESULTS: In all samples except iodidtitanium, a Nickel content of 0.012-0,034 wt% could be detected. CONCLUSION: The low nickel content in the implant material results from the production process. The nickel atoms are in solid solution in the titanium lattice. Nickel allergic patients may develop hypersensitivity reactions even due to this low nickel content. Hence, this reaction may be falsely attributed to the titanium material itself. Measurements of ion concentration in the body are helpful for quantifying the maximum content of nickel in titanium materials for surgical implant applications. In addition, technical questions related to the production of nickel free titanium materials for allergic patients have to be solved.

[Residual particle free rough surfaces after rough blasting with steel grit in total hip arthroplasty]. / Restpartikelfreie raue Oberflächen nach Stahldrahtkornstrahlen in der Hüftendoprothetik.

INTRODUCTION: Several shot peening and grit blasting techniques are used to modify the surface in the production of hip endoprostheses. A number of publications in maxillo- facial- surgery and orthopedic surgery demonstrated significant contamination on alumina blasted surfaces. Latest research studies suspected an association between surface contamination and early failure of endoprostheses associated with third body wear. Additionally, the European standard EN 12010 requires surfaces free of residual particles. The aim of this study is to evaluate the effects of rough blasting using steel grit followed by a pH dependent cleaning procedures with regard to complying with EN 12010. MATERIAL AND METHOD: Ti6Al7Nb rods were rough blasted 1 time using steel grit ("Stahldrahtkorn", hardness: 56 HRC; R+K Draht GmbH, Leisnig). All blasting procedures were carried out with a special grit blasting device with direct pressure. One Ti6Al7Nb rod each was grit blasted with 3 and 4 bar pressure and 10 rods with 5 bar pressure. Surface roughness was measured by means of Mitutoyo- Surftest 301 three times before and after grit blasting. The mean value was calculated. A field emission scanning electron microscopy (SEM, LEO 1525) was used for the detection of residual particles on the surface of the rods with a backscattered electron detector. RESULTS: By rough blasting using steel grit a mean roughness of 54,9 microm and a maximum roughness of 61,4 microm could be achieved. The surface of all rods showed a considerable contamination with steel particles after grit blasting. After the a pH- dependent cleaning procedure a residual particle free surface was detected in all samples. DISCUSSION: The European standard EN 12010 can be fulfilled using rough blasting with steel grit followed by a pH dependent cleaning procedure.

[The modular hip revision stem made of titanium alloy--influence and optimisation of bending stiffness]. / Modulare Hüftrevisionsschäfte auf Titanbasis--Einfluss und Optimierung des Steifigkeitsverhaltens.

UNLABELLED: The MRP-Titan Revision stem has proved to be a highly successful implant system for revision arthroplasty of the hip. Good and excellent clinical and radiological results with spontaneous filling of bony defects have been reported, The observation of atrophy of the proximal femur associated with stem diameters > 17mm prompted us to examine the bending stiffness of stems of various diameters. To determine their static bending characteristics, the stems were tested under axial pressure loads in accordance with Euler's buckling case. Dynamic tests were performed with the mono-axial servohydraulic test equipment MTS 810. From a stem diameter of 18 mm upwards, deflection of the stem under loading decreased disproportionately, in direct correlation with the stem stiffness. By optimising the geometry and varying the alloy it is possible to obtain a constant ISD factor for the modular MRP-Titan revision stem CONCLUSION: The MRP-Titan revision stem is a reliable implant system for revision arthroplasty of the hip. Clinical findings of atrophy of the proximal femur associated with stem diameters > 17 mm was found to be correlated with a disproportionate increase in bending stiffness. The aim of further developments will be to reduce the stiffness of larger-diameter stems by making changes to the design and/or to the alloy (Ti15Mo, Ti13Nb13Zr, Ti12Mo6Zr2Fe2).

A novel test method for evaluation of the abrasive wear behaviour of total hip stems at the interface between implant surface and bone cement.

After total hip replacement, some cemented titanium stems show above-average early loosening rates. Increased release of wear particles and resulting reaction of the peri-prosthetic tissue were considered responsible. The objective was to develop a test method for analysing the abrasive wear behaviour of cemented stems and for generating wear particles at the interface with the bone cement. By means of the novel test device, cemented hip stems with different designs, surface topographies and material compositions using various bone cements could be investigated. Before testing, the cemented stems were disconnected from the cement mantle to simulate the situation of stem loosening (debonding). Subsequently, constant radial contact pressures were applied on to the stem surface by a force-controlled hydraulic cylinder. Oscillating micromotions of the stem (+/- 250 microm; 3 x 10(6)cycles; 5 Hz) were carried out at the cement interface initiating the wear process. The usability of the method was demonstrated by testing geometrically identical Ti-6A1-7Nb and Co-28Cr-6Mo hip stems (n= 12) with definite rough and smooth surfaces, combined with commercially available bone cement containing zirconium oxide particles. Under identical frictional conditions with the rough shot-blasted stems, clearly more wear particles were generated than with the smooth stems, whereas the material composition of the hip stems had less impact on the wear behaviour.

[Surface characterisation of shot peened implants with glas beads in total hip arthroplasty]. / Oberflächenuntersuchungen an Glaskugel-gestrahlten Titanimplantaten in der Hüftendoprothetik.

UNLABELLED: Alumina-blasting is used to create a rougher surface of Titanium implants in cementless total hip arthroplasty to achieve a better bony ingrowth. An increasing number of publications in maxillofacial surgery and orthopaedic surgery show that there is a significant contamination in Alumina blasted surfaces. Latest research published an effect of contaminant particles on early loosening of endoprostheses associated with third body wear. Due to our knowledge no previous study analysed surface contamination of hip endoprostheses with glass beads. Aim of our work was to evaluate the percentage of contaminated surface of hip endoprostheses with glass beads. MATERIAL AND METHOD: The surface of 5 Ti-VPS sprayed Phoenix cups and 5 morse-taper-junctions of the MRP-Titan revision stem (Peter Brehm, Chirurgie Mechanik, Weisendorf) were analysed with respect to glass particles. Shot peening was performed with glass beads "BALLOTINI" MGL, Fa. Würth Strahlmittel. A field emission scanning electron microscopy (LEO 1525) was used for the detection of the glass-particles on the implant surface with a backscattered electron detector. The particle covering position was calculated by means of an imaging analyze software (analySIS, Soft Imaging System GmbH). RESULTS: The surface of the Ti-VPS sprayed Phoenix cups showed a contaminated area at a mean of 9.2 +/- 1.3 %, morse-taper-junctions of the MRP-Titan stem at a mean of 9.6 +/- 2.1 % with glass particle contact. DISCUSSION: The results of this study clearly show that there is a contamination of shot pinned Titanium surfaces with glass particles in a significant percentage. With respect to third body wear in total hip arthroplasty further studies are necessary to minimize contamination.

[Titanium deposits on the ceramic heads of dislocated total hip replacements]. / Titanauflagerungen auf Keramikköpfen bei luxierten Hüftendoprothesen.

INTRODUCTION: In cases of revision total hip replacement (THR) having acetabular titanium components with dislocations in the past, metallic deposits are frequently found on the ceramic heads. The aim of this study was to determine whether the metallic deposits increase surface roughness in definite areas. MATERIALS AND METHODS: Ten ceramic heads of revised THR which showed metallic deposits were investigated. The patients suffered from one to six dislocations. The prosthesis lifetime ranged from 2 weeks to 12 years. Surface structure was investigated in a scanning electron microscope (LEO 1525), and the metallic deposits characterised by means of energy dispersive x-ray analysis (EDX). RESULTS: In the area of the metallic deposits, titanium was detected by EDX. Edges with a significant increase in surface roughness were observed, partially accompanied by damage to the surface structure and loosening of Al(2)O(3) particles. DISCUSSION: Titanium deposits increase surface roughness in definite areas, which probably causes wear to the ceramic-ceramic or ceramic-polyethylene articulations due to different roughness values and surface properties. Further investigations are necessary in order to determine the importance of these findings with respect to wear and loosening of total hip arthroplasty.

[Surface characterization of Al2O3-blasted titanium implants in total hip arthroplasty]. / Oberflächenuntersuchungen an Al2O3-raugestrahlten Titanimplantaten in der Hüftendoprothetik.

INTRODUCTION: Shot peening and grit blasting techniques are used in several surface modifications for producing hip endoprostheses. Corund blasting techniques using highly pure Al2O3 particles to create a rough surface of titanium implants in cementless total hip arthroplasty achieve better osteointegration. An increasing number of publications in maxillofacial surgery and orthopedic surgery show that there is a significant contamination on corund-blasted surfaces. The latest research studies reported an effect of contaminant particles on early failure of endoprostheses associated with third body wear. The aim of our work was to evaluate the amount and particle size of Al2O3 on the implant surface. MATERIAL AND METHOD: The surface of four different geometries (five parts each, ARR titanium acetabular reinforcement ring, anisotropic Vektor cup, Vektor titanium stem and modular MRP Titan stem) were analyzed with respect to Al2O3 particles. Grit blasting was performed with Al2O3 particles, Alodur SWSK, Fa. Treibacher. Field emission scanning electron microscopy (LEO 1525) was used for the detection of the Al2O3 particles at the implant surface with a backscattered electron detector. The particle size distribution as well as the average area of the covered surface was calculated with image analyzing software (analySIS, Soft Imaging System GmbH). RESULTS: The surface of the anisotropic Vektor cup was contaminated at an average of 41.7+/-4.9%, the Vektor titanium stem at an average of 33.3+/-4.7%, the (MRP) Titan stem at an average of 30.6+/-4.2%, and the ARR titanium acetabular reinforcement ring at an average of 23.2+/-1.6 with Al2O3 particles over the whole surface orientated to the bone. DISCUSSION: The results of this study clearly show that there is contamination of rough titanium surfaces with Al2O3 particles at an unexpectedly high percentage. With respect to third body wear in total hip arthroplasty, further studies are necessary to minimize contamination of roughened surfaces and maintain sufficient roughness for osteointegration.

Effect of surface finish on the osseointegration of laser-treated titanium alloy implants.

It was the purpose of this study to examine the osseointegration of laser-textured titanium alloy (Ti6Al4V) implants with pore sizes of 100, 200, and 300 microm, specifically comparing 200-microm implants with polished and corundum-blasted surfaces in a rabbit transcortical model. Using a distal and proximal implantation site in the distal femoral cortex, each animal received all four different implants in both femora. The bone-implant interface and the newly formed bone tissue within the pores and in peri-implant bone tissue were examined 3, 6, and 12 weeks post-implantation by static and dynamic histomorphometry. Here we show that additional surface blasting of laser-textured Ti6Al4V implants with 200-microm pores resulted in a profound improvement in osseointegration, 12 weeks postimplantation. Although lamellar bone formation was found in pores of all sizes, the amount of lamellar bone within pores was linearly related to pore size. In 100-microm pores, bone remodeling occurred with a pronounced time lag relative to larger pores. Implants with 300-microm pores showed a delayed osseointegration compared with 200-microm pores. We conclude that 200 microm may be the optimal pore size for laser-textured Ti6Al4V implants, and that laser treating in combination with surface blasting may be a very interesting technology for the structuring of implant surfaces.

[Bilateral localized osteolysis after cemented total hip replacement]. / Bilaterale umschriebene Osteolyse nach zementierter Hüfttotalendoprothesenimplantation.

The incidence of focal progressive osteolysis after THR is about 8% and 56%. Most often osteolysis is correlated with macrophage-induced osteoclastic bone resorption as a sequel of inflammatory reaction to wear particles. Recently these findings were published in respect to allergic reactions to implants, their alloying constituents, or bone cement. We report about a patient who developed bilateral localized osteolysis just below the cement mantle 5 years after cemented THR with a Müller straight stem. In the middle of the osteolysis small fragments of bone cement could be detected. Epicutaneous testing showed no reaction against cobalt, chromium, or nickel. Further epicutaneous testing in respect to ingredients of the bone cement were refused by the patient. Histological examination revealed a histiocytic reaction to wear particles and surrounding giant cells. To our knowledge, this is the first case of bilateral localized osteolysis after cemented total hip replacement. Taking all results of the current case into account, it is still unclear if a lymphocytic allergic contact reaction did contribute to the sequel of this case. Reports of immunologically induced incompatibility to components of bone cement, the development of extended testing procedures, and further scientific research should contribute to optimizing the care of patients.