Hot-Pressing Metal Covalent Organic Frameworks as Personal Protection Films.

Effective personal protection is crucial for controlling infectious disease spread. However, commonly used personal protective materials such as disposable masks lack antibacterial/antiviral function and may lead to cross infection. Herein, a polyethylene glycol-assisted solvent-free strategy is proposed to rapidly synthesize a series of the donor-acceptor metal-covalent organic frameworks (MCOFs) (i.e., GZHMU-2, JNM-1, and JNM-2) under air atmosphere and henceforth extend it via in situ hot-pressing process to prepare MCOFs based films with photocatalytic disinfect ability. Best of them, the newly designed GZHMU-2 has a wide absorption spectrum (200 to 1500 nm) and can efficiently produce reactive oxygen species under sunlight irradiation, achieving excellent photocatalytic disinfection performance. After in situ hot-pressing as a film material, the obtained GZHMU-2/NMF can effectively kill E. coli (99.99%), S. aureus (99%), and H1N1 (92.5%), meanwhile possessing good reusability. Noteworthy, the long-term use of a GZHMU-2/NWF-based mask has verified no damage to the living body by measuring the expression of mouse blood routine, lung tissue, and inflammatory factors at the in-vivo level.

Rational Design of Guanidinium-Based Bio-MCOF as a Multifunctional Nanocatalyst in Tumor Cells for Enhanced Chemodynamic Therapy.

Chemodynamic therapy (CDT) has emerged as a promising approach to cancer treatment, which can break the intracellular redox state balance and result in severe oxidative damage to biomolecules and organelles with the advantages of being less dependent on external stimulation, having deep tissue-healing abilities, and being resistant to drug resistance. There is considerable interest in developing CDT drugs with high efficiency and low toxicity. In this study, a new guanidinium-based biological metal covalent organic framework (Bio-MCOF), GZHMU-1@Mo, is rationally designed and synthesized as a multifunctional nanocatalyst in tumor cells for enhanced CDT. The DFT calculation and experimental results showed that due to the ability of MoO42- ion to promote electron transfer and increase the redox active site, Cu3 clusters and MoO42- ions in GZHMU-1@Mo can synergistically catalyze the production of reactive oxygen species (ROS) from oxygen and H2O2 in tumor cells, as well as degrade intracellular reducing substances, GSH and NADH, so as to disrupt the redox balance in tumor cells. Moreover, GZHMU-1@Mo exhibits a potent killing effect on tumor cells under both normal oxygen and anaerobic conditions. Further in vitro and in vivo antiproliferation studies revealed that the GZHMU-1@Mo nanoagent displays a remarkable antiproliferation effect and effectively inhibits tumor growth. Taken together, our study provides an insightful reference benchmark for the rational design of Bio-MCOF-based nanoagents with efficient CDT.

Regio- and stereospecific cis-hydrophenoxylation of ynamides with acidic phenols.

Herein we describe a self-acid-enabled chemo-, regio-, and stereospecific cis-hydrophenoxylation of ynamides under reagent-free conditions. The presence of a non-polar solvent such as toluene was found to be beneficial to facilitate the rate-limiting proton transfer between phenols and ynamides to form an intimate ion pair, which is followed by a swift nucleophilic attack of the phenolate oxygen on keteniminium, fulfilling the overall hydrofunctionalization event. This protocol is operationally simple and easily scalable, tolerates a wide variety of functional groups, and shows good compatibility with the requirements of modern green chemistry.

Rapid and Specific Enhanced Luminescent Switch of Aniline Gas by MOFs Assembled from a Planar Binuclear Cadmium(II) Metalloligand.

Due to the low vapor pressure of aniline, it is challenging to develop a specific rapid fluorescence detection material for low concentrations of aniline gas, which is suspected to result in carcinogenicity when people are exposed by ingestion, inhalation, and skin contact. Herein, the easy-preparing Schiff base ligands were employed to construct the binuclear cadmium(II) compounds featuring a good plane and fine luminescent property, and then, the end groups were changed, making the compounds metalloligands to further build the 3D metal-organic frameworks (MOFs), named MECS-2. It is found that MECS-2 can achieve specific luminescent enhancement response for aniline gas. Furthermore, a large-scale MECS-2a film could be easily prepared by electrospinning nanoMECS-2, which presents the highly efficient and visual detection for aniline gas with the luminescent enhancement effect up to 20 times and good repeatability. Our work provides a good example for the efficient construction of MOF-based films with the fluorescence detection function for organic aromatic gases.

Tuning the Metal Ions of Prussian Blue Analogues in Separators to Enable High-Power Lithium Metal Batteries.

The Li dendrite issue is the major barrier that limits the implement of Li metal anode practically, especially at high current density. From the perspective of the nucleation and growth mechanism of the Li dendrite, we rationally develop a novel Prussian blue analogues (PBA)-derived separator, where tuning the metal ions bestows the PBAs with open metal site to confine anion movement and thereby afford a high Li+ transference number (0.78), and PBA with ordered micropores could act as an ionic sieve to selectively extract Li+ and thereby homogenize Li+ flux. This demonstrates a highly reversible Li plating/stripping cycling for 3000 h at a practically high current density (5.0 mA cm-2). Consequently, a high loading Li||LiFeO4 battery (∼10.0 mg cm-2) demonstrates ultralong cycling life at high current densities (∼5.1 mA cm-2). This work highlights the prospect of optimizing PBAs in regulating ion transport behavior to enable high-power Li metal batteries.

Single-Atom Zinc and Anionic Framework as Janus Separator Coatings for Efficient Inhibition of Lithium Dendrites and Shuttle Effect.

The two key problems for the industrialization of Li-S batteries are the dendrite growth of lithium anode and the shuttle effect of lithium polysulfides (LiPSs). Herein, we report the Janus separator prepared by coating anionic Bio-MOF-100 and its derived single-atom zinc catalyst on each side of the Celgard separator. The anionic metal-organic framework (MOF) coating induces the uniform and rapid deposition of lithium ions, while its derived single-atom zinc catalyzes the rapid transformation of LiPSs, thus inhibiting the lithium dendrite and shuttle effect simultaneously. Consequently, compared with other reported Li-S batteries assembled with single-atomic catalysts as separator coatings, our SAZ-AF Janus separator showed stable cyclic performance (0.05% capacity decay rate at 2 C with 1000 cycles), outstanding performance in protecting lithium anode (steady cycle 2800 h at 10 mAh cm-2), and equally excellent cycling performance in Li-SeS2 or Li-Se batteries. Our work provides an effective separator coating design to inhibit shuttle effect and lithium dendrite.

Oxygen Vacancy-Rich Mixed-Valence Cerium MOF: An Efficient Separator Coating to High-Performance Lithium-Sulfur Batteries.

Mixed-valence metal-organic frameworks (MOFs) have exhibited unique potential in fields such as catalysis and gas separation. However, it is still an open challenge to prepare mixed-valence MOFs with isolated Ce(IV, III) arrays due to the easy formation of CeIII under the synthetic conditions for MOFs. Meanwhile, the performance of Li-S batteries is greatly limited by the fatal shuttle effect and the slow transmission rate of Li+ caused by the inherent characteristics of sulfur species. Here, we report a mixed-valence cerium MOF, named CSUST-1 (CSUST stands for Changsha University of Science and Technology), with isolated Ce(IV, III) arrays and abundant oxygen vacancies (OVs), synthesized as guided by the facile and elaborate kinetic stability study of UiO-66(Ce), to work as an efficient separator coating for circumventing both issues at the same time. Benefiting from the synergistic function of the Ce(IV, III) arrays (redox couples), the abundant OVs, and the open Ce sites within CSUST-1, the CSUST-1/CNT composite, as a separator coating material in the Li-S battery, can remarkably accelerate the redox kinetics of the polysulfides and the Li+ transportation. Consequently, the Li-S cell with the CSUST-1/CNT-coated separator exhibited a high initial specific capacity of 1468 mA h/g at 0.1 C and maintained long-term stability for a capacity of 538 mA h/g after 1200 cycles at 2 C with a decay rate of only 0.037% per cycle. Even at a high sulfur loading of 8 mg/cm2, the cell with the CSUST/CNT-coated separator still demonstrated excellent performance with an initial areal capacity of 8.7 mA h/cm2 at 0.1 C and retained the areal capacity of 6.1 mA h/cm2 after 60 cycles.

Three-Dimensional (3D) Nanostructured Skeleton Substrate Composed of Hollow Carbon Fiber/Carbon Nanosheet/ZnO for Stable Lithium Anode.

The practical applications of Li metal batteries (LMBs) have long been limited by the obstacles of low Coulombic efficiency (CE) and formation of dendrites on Li metal electrode. Herein, we demonstrated the synthesis of a novel three-dimensional (3D) nanostructured skeleton substrate composed of nitrogen-doped hollow carbon fiber/carbon nanosheets/ZnO (NHCF/CN/ZnO) using 2-methylimidazole (2-MIZ)-coated 3D cloth as a scaffold. The mechanism of formation of this novel hierarchical structure was investigated. The multilayered hierarchical structure and abundant lithiophilic nucleation sites of the substrate provide a stable environment for the deposition and stripping of lithium metal, thus preventing the generation of lithium dendrites. Consequently, the lithium anode based on the NHCF/CN/ZnO current collector demonstrated an excellent Coulombic efficiency of 96.47% after 400 cycles at 0.5 mA cm-2. The prepared NHCF/CN/ZnO/Li electrode also showed outstanding cycling performance of over 800 h and an ultralow voltage hysteresis of less than 30 mV in a symmetric cell at 5 mA cm-2 and 5 mAh cm-2. Even at a high loading of the cathode with 10.4 mg cm-2, the full cell of NHCF/CN/ZnO/Li anode with LiFePO4 can also work very well. Our work offers a path toward the facial preparation of 3D hierarchical structure for high-performance lithium metal batteries.

MOF-derived Ni3S4 Encapsulated in 3D Conductive Network for High-Performance Supercapacitor.

Transition-metal sulfide is a good kind of material for supercapacitors because of the large capacity. Nevertheless, the low electroconductivity, slow reaction kinetics, and limited active centers lead to poor electrochemical properties such as long-term cycling stability. In the present work, nano nickel metal-organic framework (Ni-MOF) was constructed by using the nitrogen-rich functional group ligand 2,4,6-tris(3,5-dicarboxylphenylamino)-1,3,5-triazin and compounded with carbon nanotubes (CNTs) to prepare Ni-MOF/CNTs composite, which was used as a precursor to prepare the MOFs-derived NC/Ni-Ni3S4/CNTs composite with the Ni3S4 uniformly distributed in the three-dimensional (3D) conductive network. The rich nitrogen doping and 3D conductive network constructed by CNTs improved the conductivity, prompted the rapid entry of electrolyte, and improved the reaction kinetics of NC/Ni-Ni3S4/CNTs, thus obtained excellent specific capacitance, coulomb efficiency, and cyclic stability. The specific capacitance of NC/Ni-Ni3S4/CNTs is 1489.9 F/g at 1 A/g, which remains 800 F/g at 10 A/g, showing good rate performance.

Saclike-silicon nanoparticles anchored in ZIF-8 derived spongy matrix as high-performance anode for lithium-ion batteries.

The carbon layer with good electrical conductivity and outstanding mechanical stability are essential in designing high-performance silicon/carbon (Si/C) anodes to replace the commercial graphite in lithium-ion batteries (LIBs). In terms of solving the two inherent defects of poor conductivity and big volume change of silicon, we fabricate a spongy carbon matrix derived from ZIF-8 to anchor saclike silicon synthesized by molten salt magnesiothermic reduction method. This spongy matrix can anchor saclike silicon to provide a stable reaction interface and support fast electronic transmission. At the same time, buffer space in saclike Si nanoparticles and spongy matrix can synergistically accommodate the volume change of Si to maintain the integrity of the electrode. The resulting composite with a high Si content of 77.58% exhibits good capacities of 1448 mAh g-1 at 2 A g-1 and 848 mAh g-1 at 4 A g-1 after 500 cycles. High initial coulombic efficiency of 84% at 0.2 A g-1 is also exhibited in the first three activation cycles. Therefore, this novel multifunctional N-doped spongy matrix can supply multifaceted benefits in accommodation of volumetric variation, enhancement of conductivity, and integrity of structure during cycling.

Cerium Based Metal-Organic Frameworks as an Efficient Separator Coating Catalyzing the Conversion of Polysulfides for High Performance Lithium-Sulfur Batteries.

In this work, we demonstrate cerium (Ce) based metal-organic frameworks (MOFs) combined with carbon nanotubes (CNTs) to form Ce-MOF/CNT composites as separator coating material in the Li-S battery system, which showed excellent electrochemical performance even under high sulfur loading and much better capacity retention. At the sulfur loading of 2.5 mg/cm2, initial specific capacity of 1021.8 mAh/g at 1C was achieved in the Li-S cell with the Ce-MOF-2/CNT coated separator, which was slowly reduced to 838.8 mAh/g after 800 cycles with a decay rate of only 0.022% and the Coulombic efficiency of nearly 100%. Even at a higher sulfur loading of 6 mg/cm2, the cell based on Ce-MOF-2/CNT separator coating still exhibited excellent performance with initial specific capacity of 993.5 mAh/g at 0.1 C. After 200 cycles, the specific capacity of 886.4 mAh/g was still retained. The excellent performance is ascribed to the efficient adsorption of the Ce-MOF-2 to Li2S6 species and its catalytic effect toward conversion of polysulfides, resulting in suppressed shuttle effect of polysulfides in the Li-S batteries.

Efficient Encapsulation of Small S2-4 Molecules in MOF-Derived Flowerlike Nitrogen-Doped Microporous Carbon Nanosheets for High-Performance Li-S Batteries.

Lithium-sulfur (Li-S) battery is regarded as one of the most promising next-generation efficient energy storage systems because of its ultrahigh theoretical capacity of 1675 mAh/g and energy density of 2600 Wh/kg accompanied by the environmental benignity and abundance from natural sulfur. However, the insulating nature of sulfur and the dissolution of the polysulfides Li2S n (4 ≤ n ≤ 8) seriously restrict its practical application. The metastable small sulfur molecules (S2-4) stored in microporous carbon (pore size of <0.6 nm) as the active materials can avoid the production of the soluble polysulfide and solve the shuttle effect thoroughly. In addition, the conductivity of sulfur can be also improved. However, the preparation of microporous carbon materials with reasonable pore size and unique morphology for efficiently encapsulating S2-4 is still challenging. Herein, three flowerlike microporous nitrogen-doped carbon nanosheets with the pore size of <0.6 nm (namely, FMNCN-800, -900, and -1000) as the cathode materials in Li-S batteries were obtained from temperature-dependent carbonization of the metal-organic framework (MOF), Zn-TDPAT, which was from the simply reflux reaction of N-rich ligand H6TDPAT with Zn(II) salt. Our study showed that the FMNCN-900 from carbonization of Zn-TDPAT at 900 °C has suitable pore volume and nitrogen content, accommodating small S2-4 molecules in its micropores with the mass uptake of about 45%. Meanwhile, the appropriate amount of the nitrogen doping and the unique nanostructure of the flowerlike carbon nanosheet in the FMNCN-900 can effectively support its fast electronic transmission and lithium-ion conduction. The resulting S@FMNCN-900 composite cathode material presents the excellent electrochemical property in the Li-S battery (here the carbonate as electrolytes) with a reversible capacity of about 1220 mAh/g at 0.1C after 200 cycles and even 727 mAh/g at 2C after the long-term cycle of 1000 with only around 0.02% capacity loss per cycle. Obviously, the results indicate that the delicate construction of MOF-derived nitrogen-doped microporous carbon nanosheet is a promising strategy to develop novel electrode material for high-performing Li-S batteries.

Confinement of polysulfides within bi-functional metal-organic frameworks for high performance lithium-sulfur batteries.

A lithium-sulfur (Li-S) battery is regarded as the most promising candidate for next generation energy storage systems, because of its high theoretical specific capacity (1675 mA h g-1) and specific energy (2500 W h kg-1), as well as the abundance, low cost and environmental benignity of sulfur. However, the soluble polysulfides Li2Sx (4 ≤ x ≤ 8) produced during the discharge process can cause the so-called "shuttle effect" and lead to low coulombic efficiency and rapid capacity fading of the batteries, which seriously restrict their practical application. Using porous materials as hosts to immobilize the polysulfides is proved to be an effective strategy. In this article, a dual functional cage-like metal-organic framework (Cu-MOF), Cu-TDPAT, combining the Lewis basic sites from the nitrogen atoms of the ligand H6TDPAT with the Lewis acidic sites from Cu(ii) open metal sites (OMSs), was employed as the sulfur host in a Li-S battery for lithium ions and polysulfide anions (Sx2-). In addition, the size of nano-Cu-TDPAT was also optimized by microwave synthesis to reduce the internal resistance of the batteries. The electrochemical test results showed that the optimized Cu-TDPAT material can efficiently confine the polysulfides within the MOF, and the resultant porous S@Cu-TDPAT composite cathode material with the size of 100 nm shows good cycling performance with a reversible capacity of about 745 mA h g-1 at 1C (1C = 1675 mA g-1) after 500 cycles, to the best of our knowledge, which is higher than those of all reported S@MOF cathode materials. The DFT calculation and XPS data indicate that the good cycling performance mainly results from the dual functional binding sites (that is, Lewis acid and base sites) in nanoporous Cu-TDPAT, providing the comprehensive and robust interaction with the polysulfides to overcome their dissolution and diffusion into the electrolyte. Clearly, our work provides a good example of designing MOFs with suitable interaction sites for the polysulfides to achieve S@MOF cathode materials with excellent cycling performance by multiple synergistic effects between nanoporous host MOFs and the polysulfides.

Pillar-Layered Metal-Organic Framework with Sieving Effect and Pore Space Partition for Effective Separation of Mixed Gas C2H2/C2H4.

The removal of acetylene from the industrial feed gas to purify the ethylene is an important and challenging issue. The adsorption-based separation is a more environmentally friendly and cost-effective method compared to the current removal approaches such as partial hydrogenation and solvent extraction, while facing the challenge of developing materials with high C2H2/C2H4 selectivity and C2H2 capacity. Herein, by expanding mixed-metal organic frameworks (M'MOFs) structure with high C2H2/C2H4 selectivity, we report a pillar-layered MOF, {[Cd5(MPCZ)2(BDC)3(NO3)2(H2O)4]·G}n (MECS-5), which not only inherits the sieving effects of M'MOF series but also develops its own characteristic-the 2D layer with expanding space and the plane pore-partition group to "cover" it. MECS-5 shows higher ideal adsorption solution theory C2H2/C2H4 selectivity than the most reported MOFs, especially more than 5 times higher than MOF-74 series while displaying great enhancement in the C2H2 capacity, more than 2 times higher compared to the M'MOF. The column breakthrough experiment further proves the possibility of MECS-5a for real industrial ethylene purification.

2-Fold Interpenetrating Bifunctional Cd-Metal-Organic Frameworks: Highly Selective Adsorption for CO2 and Sensitive Luminescent Sensing of Nitro Aromatic 2,4,6-Trinitrophenol.

A robust primitive diamond-type topology 3-D metal-organic framework (MOF) of {[Cd4(hbhdpy)2(bdc)3(DMA)2]·(H2O)4}n (1, DMA = N,N-dimethylacetamide) was constructed from the planar secondary building units of the dinuclear cadmium clusters, Cd2(µ2-O)2, and two linear organic linkers of the new multidentate Schiff base of 4-(2-hydroxy-3-methoxy-benzyli-denehydrazino-carbonyl)-N-pyridin-4-yl-benzamide (Hhbhdpy) through the solvothermal reaction. 1 presents a 2-fold interpenetrating network along with confined narrow channels and rich acylamide groups as well as potential metal open sites for excellent selective CO2 uptake over CH4/N2 and high luminescent response for 2,4,6-trinitrophenol (TNP) in DMA solution under ambient conditions. With 2-amino-1,4-dicarboxy-benzene (H2bdc-NH2) replacing H2bdc, an amine-functionalized MOF of {[Cd4(hbhdpy)2(bdc-NH2)3 (DMA)2]·(H2O)4}n (1-NH2) as an isomorphism of 1, was synthesized under the same reaction conditions. Compared with 1, the corresponding bifunctional features of 1-NH2 is more obvious. To the best of our knowledge, it is the first reported interpenetrating Cd-MOFs with highly sensitive luminescence response for TNP molecules combined with excellent selectivity for CO2/N2 and CO2/CH4.

Anion-dependent assembly of four sensitized near-infrared luminescent heteronuclear Zn(II)-Yb(III) Schiff base complexes from a trinuclear Zn(II) complex.

Four anion-dependent 0D Zn(II)-Yb(III) heterometallic Schiff base complexes, [YbZn2L2(OAc)4]·ClO4 (2), YbZnL2(NO3)3 (3), [(YbL)2(H2O)Cl(OAc)]2·[ZnCl4]2 (4), and YbZnL(OAc)4 (5), were assembled through central metal substitution or reconstruction from homotrinuclear Zn(II) complex {[(Zn(OAc)(H2O)L]2Zn}(ClO4)2·4H2O [1; HL = 2-ethoxy-6-[(pyridin-2-ylmethylimino)methyl]phenol] with different Yb(III)X3 salts [X = ClO4 (2), NO3 (3), Cl (4), and OAc (5)], in which the Zn(II)-sensitized near-infrared luminescent performances in the four complexes 2-5 are closely related to their structural models.

Temperature-dependent assemblies from a 2-D triple-stranded meso-helical layer to a 3-D chain-layer metal-organic framework.

Two different crystal forms, namely {[Dy2(mpda)3(H2O)2]·H2O}n (1) and [Dy2(mpda)3(H2O)4]n (2), were obtained from the reaction of multidentate 2,6-dimethylpyridine-3,5-dicarboxylic acid (H2mpda) with Dy2O3 at different temperatures. Structural analysis reveals that compound 1 is a 2-D triple-stranded meso-helical layer, and 2 a 3-D chain-layer framework. The fluorescent measure shows that compound 1 is a promising luminescent probe for various metals with a remarkable "on­off" switch of emission, mainly deriving from many pairs of inversely arranged 4-aza bowl-like crown ethers distributed in the 2-D helical plane. Moreover, compound 1 presents noticeable hydrogen-sorption at medium pressure.

Temperature-/solvent-dependent low-dimensional compounds based on quinoline-2,3-dicarboxylic acid: structures and fluorescent properties.

A series of 0-D, 1-D, and 2-D metal-organic compounds through reactions of quinoline-2,3-dicarboxylic acid (2,3-H(2)qldc) with transition metal salts MCl(2), namely, M(2,3-Hqldc)(2)(H(2)O)(2) (M = Co(1), Zn(4) and Cd(7)), [M(3-qlc)(2)(H(2)O)(2)](n) (M = Co(2), Zn(5) and Cd(8)), M(2-qldc-3-OCH(3))(2)(CH(3)OH)(2) (M = Co(3) and Zn(6)) and [Cd(2,3-qldc-OCH(3))(µ(2)-Cl)](2n) (9) (where, 3-Hqlc = quinoline-3-carboxylic acid and 2-qldc-3-OCH(3) = 3-(methoxycarbonyl)quinoline-2-carboxylic acid), were synthesized and characterized by elemental analysis, IR, thermogravimetric analysis (TG), and single-crystal X-ray diffraction. When the temperature ranged from room temperature to 70 °C, three isomorphous mononuclear complexes 1, 4 and 7 were obtained in H(2)O/H(2)O + CH(3)OH. As the temperature rose further to above 90 °C, due to the decomposition of 2-position carboxyl group in ligand 2,3-H(2)qldc, the same reactions, respectively, produced three isomorphous 2-D layer-like structures 2, 5 and 8 with 4(4) topology in water. By contrast, when the mixed solvent of H(2)O + CH(3)OH at a 1 : 1 ratio (v/v) was applied, the three above-mentioned reactions respectively gave compounds 3, 6 and 9 with the 3-position esterification of 2,3-H(2)qldc. Compounds 3 and 6 are mononuclear and isomorphous, while complex 9 has a 1-D double-stranded chain-like structure connected by two µ(2)-Cl bridges. Obviously, these results reveal that the reaction temperature and solvent play a critical role in structural direction of these low-dimensional compounds. Meanwhile, the photoluminescent property of the selected compounds is also investigated.