Optimizing bioelectromethanosynthesis of CO2 and membrane fouling mitigation in MECs via in-situ biogas recirculation.

The CO2 bioelectromethanosynthesis via two-chamber microbial electrolysis cell (MEC) holds tremendous potential to solve the energy crisis and mitigate the greenhouse gas emissions. However, the membrane fouling is still a big challenge for CO2 bioelectromethanosynthesis owing to the poor proton diffusion across membrane and high inter-resistance. In this study, a new MEC bioreactor with biogas recirculation unit was designed in the cathode chamber to enhance secondary-dissolution of CO2 while mitigating the contaminant adhesion on membrane surface. Biogas recirculation improved CO2 re-dissolution, reduced concentration polarization, and facilitated the proton transmembrane diffusion. This resulted in a remarkable increase in the cathodic methane production rate from 0.4 mL/L·d to 8.5 mL/L·d. A robust syntrophic relationship between anodic organic-degrading bacteria (Firmicutes 5.29%, Bacteroidetes 25.90%, and Proteobacteria 6.08%) and cathodic methane-producing archaea (Methanobacterium 65.58%) enabled simultaneous organic degradation, high CO2 bioelectromethanosynthesis, and renewable energy storage.

Enhanced hydrolysis and methane yield of temperature-phased dewatered sludge anaerobic digestion by microbial electrolysis cell.

Temperature-phased anaerobic digestion (TPAD) and microbial electrolysis cell (MEC) are both able to improve hydrolysis and methane yield during anaerobic digestion (AD) of dewatered sludge. However, the effect of TPAD and MEC integration at different temperatures and different phases is unclear. This study investigated the effect of the integration of intermittent energization MEC in different phases of TPAD on the digestion of dewatered sludge. Thermophilic and MEC hydrolysis could release higher total ammonia nitrogen of 186.0% and 10.3% than control, mesophilic methanogenesis phase integrated with MEC relieved the ammonia inhibition and accelerated the acid utilization leading to the relief of acid accumulation. The ultimate methane yield of the TPAD integrated with MEC was increased by 118.9%, in which the relative abundance of Methanothermobacteria and Methanosarcina was increased. Therefore, intermittent energization MEC integrated TPAD synchronously improved the hydrolysis and methane yield.

3D-Printed Biomimetic Structural Colors.

Resolution control and expansibility have always been challenges to the fabrication of structural color materials. Here, a facile strategy to print cholesteric liquid crystal elastomers (CLCEs) into complex structural color patterns with variable resolution and enhanced expansibility is reported. A volatile solvent is introduced into the synthesized CLC oligomers, modifying its rheological properties and allowing direct-ink-writing (DIW) under mild conditions. The combination of printing shear flow and anisotropic deswelling of ink drives the CLC molecules into an ordered cholesteric arrangement. The authors meticulously investigate the influence of printing parameters to achieve resolution control over a wide range, allowing for the printing of multi-sized 1D or 2D patterns with constant quality. Furthermore, such solvent-cast direct-ink-writing (DIW) strategy is highly expandable and can be integrated easily into the DIW of bionic robots. Multi-responsive bionic butterfly and flower are printed with biomimetic in both locomotion and coloration. Such designs dramatically reduced the processing difficulty of precise full-color printing and expanded the capability of structural color materials to collaborate with other systems.

Nitrogen removal from dewatering liquid of landfill sludge by partial nitrification and denitrification.

Two pilot-scale two-stage anoxic/oxic membrane bioreactors were operated at different dissolved oxygen (DO) levels to evaluate nitrogen removal performances for treating landfill sludge dewatering liquid. Under either high (5.0-6.0 mg/L) or conventional DO (2.0-3.0 mg/L) conditions, partial nitrification (PN)-denitrification was both achieved, and high-concentration free ammonia (FA) ensured stable PN. The high DO system exhibited higher nitrite accumulation (98.5 %) and nitrogen removal (98.0 %), and its nitrogen removal was mainly ascribed to PN-denitrification (53.8 %). Kinetic inhibition tests and microbial sequencing results demonstrated that high DO condition improved the abundance and ability of ammonia-oxidizing bacteria (AOB) rather than nitrite-oxidizing bacteria under the FA inhibition. Pseudomonas, Thauera, and Soehngenia were characteristic genus in the high DO system, and Nitrosomonas was only AOB. Metagenomic analysis confirmed the important role of PN on nitrogen removal in high DO system. This provides valuable references for the efficient and economic treatment of ammonia-rich wastewater.

δ-Tocotrienol preconditioning improves the capability of bone marrow-derived mesenchymal stem cells in promoting wound healing by inhibiting BACH1-related ferroptosis.

Wound healing is a complex physiological process for maintaining skin integrity after a wound. Bone marrow-derived mesenchymal stem cells (BMSCs) are excellent cellular candidates for wound healing, which could be enhanced by exogenous stimulation. We aimed to explore the role of δ-Tocotrienol (δ-TT) in BMSC ability of wound healing. Firstly, transcriptome and single-cell analysis were used to explore the genes and pathways related to ferroptosis in wound tissues. In vitro, cell proliferation, migration, and angiogenesis of δ-TT-BMSCs were detected. In addition, qRT-PCR and immunofluorescence (IF) were applied for observing the promoting wound healing ability of δ-TT-BMSC conditioned medium (CM) on NIH-3T3 and PAM-212 cells. The level of ferroptosis was determined by the mitochondrial membrane potential and total/lipid reactive oxygen species (ROS) in the cells and the morphological changes of mitochondria were observed by transmission electron microscope. The BTB and CNC homology 1 (BACH1) expression and activation of the PI3K/AKT signaling pathway were detected by IF and western blot (WB). The effect of δ-TT-BMSCs on wound healing was observed in vivo. The regulatory mechanism of δ-TT-BMSCs on ferroptosis was verified by IHC and IF staining. In vitro, δ-TT-BMSCs declined the level of lipid ROS in NIH-3T3 and PAM-212 cells and enhanced mitochondrial membrane potential. In vivo, δ-TT-BMSCs promoted wound healing in mice by decreasing ferroptosis. In terms of mechanism, δ-TT-BMSCs inhibited the expression of BACH1 and activated PI3K/AKT signaling pathway. This study demonstrated the ability of δ-TT-BMSCs to promote wound healing by inhibiting BACH1-related ferroptosis. In addition, PI3K/AKT signaling pathway was activated by δ-TT-BMSCs and could be involved in wound healing. δ-TT-BMSCs might be a promising strategy for treating wounds.

3D-Printed Intrinsically Stretchable Organic Electrochemical Synaptic Transistor Array.

Organic electrochemical transistors (OECTs) for skin-like bioelectronics require mechanical stretchability, softness, and cost-effective large-scale manufacturing. However, developing intrinsically stretchable OECTs using a simple and fast-response technique is challenging due to limitations in functional materials, substrate wettability, and integrated processing of multiple materials. In this regard, we propose a fabrication method devised by combining the preparation of a microstructured hydrophilic substrate, multi-material printing of functional inks with varying viscosities, and optimization of the device channel geometries. The resulting intrinsically stretchable OECT array with synaptic properties was successfully manufactured. These devices demonstrated high transconductance (22.5 mS), excellent mechanical softness (Young's modulus ∼ 2.2 MPa), and stretchability (∼30%). Notably, the device also exhibited artificial synapse functionality, mimicking the biological synapse with features such as paired-pulse depression, short-term plasticity, and long-term plasticity. This study showcases a promising strategy for fabricating intrinsically stretchable OECTs and provides valuable insights for the development of brain-computer interfaces.

Bioelectrochemical anaerobic membrane bioreactor enables high methane production from methanolic wastewater: Roles of microbial ecology and microstructural integrity of anaerobic biomass.

The disintegration of anaerobic sludge and blockage of membrane pores has impeded the practical application of anaerobic membrane bioreactor (AnMBR) in treating methanolic wastewater. In this study, bioelectrochemical system (BES) was integrated into AnMBR to alleviate sludge dispersion and membrane fouling as well as enhance bioconversion of methanol. Bioelectrochemical regulation effect induced by BES enhanced methane production rate from 4.94 ± 0.52 to 5.39 ± 0.37 L/Lreactor/d by accelerating the enrichment of electroactive microorganisms and the agglomeration of anaerobic sludge via the adhesive and chemical bonding force. 16 S rRNA gene high-throughput sequencing demonstrated that bioelectrochemical stimulation had modified the metabolic pathways by regulating the key functional microbial communities. Methanogenesis via the common methylotrophic Methanomethylovorans was partially substituted by the hydrogenotrophic Candidatus_Methanofastidiosum, etc. The metabolic behaviors of methanol are bioelectrochemistry-dependent, and controlling external voltage is thus an effective strategy for ensuring robust electron transfer, low membrane fouling, and long-term process stability.

Enhanced treatment of sludge drying condensate by A/O-MBR process: Microbial activity and community structure.

With the rapid increase of sludge production from sewage treatment plants, the treatment of sludge drying condensate rich in a large amount of pollutants urgently needs to be addressed. Due to the unique characteristics of sludge drying condensate (high ammonia nitrogen and COD concentration), there are almost no reports on biological treatment methods specifically targeting sludge drying condensate. In this study, A/O-MBR process was proposed for sludge drying condensate treatment and the effects of ammonia nitrogen loads, alkalinity and aeration intensity were explored. Experimental results show that under the ammonia nitrogen load of 0.35 kg NH4+-N/(m3·d) and the aeration intensity of 0.5 m3/(m2·min), the removal rate of COD and NH4+-N could reach 94% and 99.86% with the addition of alkalinity (m(NaHCO3): m(NH4+-N) = 7:1), respectively. The distribution of living and dead microbial cells in the activated sludge of three reactors also proved that the supplement of alkalinity in the influent can ensure the feasible living conditions for microorganisms. In addition to traditional nitrifying bacteria, through the supplementation of alkalinity and the reduction of aeration intensity, the system had also domesticated high abundance heterogeneous nitrification aerobic denitrification (HN-AD) and aerobic denitrification bacteria (both more than 10% of the total bacterial count). The denitrification process of sludge drying condensate was simplified and the denitrification efficiency was greatly improved. The findings of this study could provide important theoretical guidance for the biological treatment process of sludge drying condensate.

Biochar-supported magnesium oxide as high-efficient lead adsorbent with economical use of magnesium precursor.

With unique porous structure inherited from lignocellulose, biochar was an appropriate carrier for small-size MgO materials, which could simplify the synthetic process and better solve agglomeration and separation problems during adsorption. Biochar-supported MgO was prepared with impregnation method. Under different synthesis conditions, the obtained MgO presented diverse properties, and moderate pyrolysis condition was conducive to the improvement of Mg conversion rate. The Pb(II) capacity was highly correlated with Mg content, rather than the specific surface area. Reducing the pyrolysis temperature or increasing the usage of supporter could improve adsorption efficiency when using Mg content-normalized capacity as the criterion. The better release ability of Mg, contribute by the higher extent of hydration and better spread of MgO, were the critical factors. The maximal Mg content-normalized capacity could reach 0.932 mmol·mmol-Mg-1 with the mass ratio of biochar/MgCl2·6H2O = 4:1 at the pyrolysis temperature of 600 °C. Considering the ultimate utilization efficiency of Mg in precursor, the optimum Mg consumption-normalized capacity was 0.744 mmol·mmol-Mg-1 with the mass ratio of biochar/MgCl2·6H2O = 1:1 at 600 °C.

Influence of adsorption sites of biochar on its adsorption performance for sulfamethoxazole.

In this study, the effects of various types of key adsorption sites on biochar were investigated on its adsorption capacity for sulfamethoxazole (SMX). The biochar obtained by carbonization of corncob at 800 °C (named CC800) was applied to the adsorption of SMX in aqueous environment. The adsorption of SMX by CC800 exhibited a "Three-stage downward adsorption ladder" characteristic in the whole pH range, which was attributed to the different mechanisms corresponding to different adsorption sites of CC800. The organic solvent method and heat treatment method restored the adsorption sites of CC800 after saturated adsorption. And the results revealed that the pore structure and aromatic structure under acidic conditions, and surface functional groups and pore structure under alkaline conditions were confirmed to be key SMX adsorption sites. The adsorption energies of each adsorption mechanism were calculated by density functional theory (DFT), and their order was (-)CAHB (-COO-) > π+-π EDA interaction > (-)CAHB (-O-) > pore filling mechanism > π-π EDA interaction. Based on the above studies, the adsorption performance of biochar to SMX can be improved by targeted modification of its micropore structure, surface functional groups, and aromatic structures.

Insights into biodegradation behaviors of methanolic wastewater in up-flow anaerobic sludge bed (UASB) reactor coupled with in-situ bioelectrocatalysis.

Granular sludge disintegration and washing out pose a challenge to up-flow anaerobic sludge bed (UASB) reactor treating methanolic wastewater. Herein, in-situ bioelectrocatalysis (BE) was integrated into UASB (BE-UASB) reactor to alter microbial metabolic behaviors and enhance the re-granulation process. BE-UASB reactor exhibited the highest methane (CH4) production rate of 388.0 mL/Lreactor/d and chemical oxygen demand (COD) removal of 89.6 % at 0.8 V. Sludge re-granulation was strengthened with particle size over 300 µm of up to 22.4%. Bioelectrocatalysis stimulated extracellular polymeric substances (EPS) secretion and formation of granules with rigid [-EPS-cell-EPS-] matrix by enhancing the proliferation of key functional microorganisms (Acetobacterium, Methanobacterium, and Methanomethylovorans) and diversifying metabolic pathways. Particularly, a high Methanobacterium richness (10.8%) drove the electroreduction of CO2 into CH4 and reduced its emissions (52.8%). This study provides a novel bioelectrocatalytic strategy for controlling granular sludge disintegration, which will facilitate the practical application of UASB in methanolic wastewater treatment.

Lipogenesis promotes mitochondrial fusion and maintains cancer stemness in human NSCLC.

Cancer stem-like cells (CSCs) are critically involved in cancer metastasis and chemoresistance, acting as one major obstacle in clinical practice. While accumulating studies have implicated the metabolic reprogramming of CSCs, mitochondrial dynamics in such cells remain poorly understood. Here we pinpointed OPA1hi with mitochondrial fusion as a metabolic feature of human lung CSCs, licensing their stem-like properties. Specifically, human lung CSCs exerted enhanced lipogenesis, inducing OPA1 expression via transcription factor SAM Pointed Domain containing ETS transcription Factor (SPDEF). In consequence, OPA1hi promoted mitochondrial fusion and stemness of CSCs. Such lipogenesishi, SPDEFhi, and OPA1hi metabolic adaptions were verified with primary CSCs from lung cancer patients. Accordingly, blocking lipogenesis and mitochondrial fusion efficiently impeded CSC expansion and growth of organoids derived from patients with lung cancer. Together, lipogenesis regulates mitochondrial dynamics via OPA1 for controlling CSCs in human lung cancer.

Dual encoder network with transformer-CNN for multi-organ segmentation.

Medical image segmentation is a critical step in many imaging applications. Automatic segmentation has gained extensive concern using a convolutional neural network (CNN). However, the traditional CNN-based methods fail to extract global and long-range contextual information due to local convolution operation. Transformer overcomes the limitation of CNN-based models. Inspired by the success of transformers in computer vision (CV), many researchers focus on designing the transformer-based U-shaped method in medical image segmentation. The transformer-based approach cannot effectively capture the fine-grained details. This paper proposes a dual encoder network with transformer-CNN for multi-organ segmentation. The new segmentation framework takes full advantage of CNN and transformer to enhance the segmentation accuracy. The Swin-transformer encoder extracts global information, and the CNN encoder captures local information. We introduce fusion modules to fuse convolutional features and the sequence of features from the transformer. Feature fusion is concatenated through the skip connection to smooth the decision boundary effectively. We extensively evaluate our method on the synapse multi-organ CT dataset and the automated cardiac diagnosis challenge (ACDC) dataset. The results demonstrate that the proposed method achieves Dice similarity coefficient (DSC) metrics of 80.68% and 91.12% on the synapse multi-organ CT and ACDC datasets, respectively. We perform the ablation studies on the ACDC dataset, demonstrating the effectiveness of critical components of our method. Our results match the ground-truth boundary more consistently than the existing models. Our approach gains more accurate results on challenging 2D images for multi-organ segmentation. Compared with the state-of-the-art methods, our proposed method achieves superior performance in multi-organ segmentation tasks. Graphical Abstract The key process in medical image segmentation.

Conformational transition-induced simultaneous fluorescence enhancement of oxytetracycline and rhodamine B under a single excitation wavelength.

Since the abuse of antibiotic oxytetracycline (OTC) poses a serious threat to the environment and human health, it is of great importance to develop sensitive fluorescent probes for its rapid and in situ detection. Herein, a dual fluorescence response probe based on an aluminum-incorporated metal-organic framework (MOF) was presented for OTC assay. Unlike internal references that demonstrate an independent and stable fluorescence signal intensity in traditional dual-emissive probes, the fluorescence of rhodamine B immobilized in a prepared probe was gradually enhanced at a 585 nm emission wavelength with increasing concentrations of OTC under 405 nm excitation, while OTC also experienced an obvious fluorescence enhancement at a 521 nm emission wavelength due to a molecular conformation transition from the twisted to the extended state, realizing a molecular conformational transition-induced dual fluorescence enhancement for OTC detection under a single excitation wavelength. In addition to the mechanism exploration and double linear range for OTC quantification with nM level detection limits in solution, a paper-based portable test strip was successfully fabricated by loading the probe on glass fiber filter paper with an obvious fluorescence color change from orange to yellow upon increasing the addition of OTC. We expect that the proposed probe in this work would provide an example for the design of organic fluorophore-based sensors exhibiting multiple fluorescence responses under a single excitation.

The ferroxidases are critical for Fe(II) oxidation in xylem to ensure a healthy Fe allocation in Arabidopsis thaliana.

The long-distance transport of iron (Fe) in the xylem is critical for maintaining systemic Fe homeostasis in plants. The loading form of Fe(II) into the xylem and the long-distance translocation form of Fe(III)-citrate have been identified, but how Fe(II) is oxidized to Fe(III) in the xylem remains unknown. Here, we showed that the cell wall-resided ferroxidases LPR1 and LPR2 (LPRs) were both specifically expressed in the vascular tissues of Arabidopsis thaliana, while disruption of both of them increased Fe(II) in the xylem sap and caused excessive Fe deposition in the xylem vessel wall under Fe-sufficient conditions. As a result, a large amount of Fe accumulated in both roots and shoots, hindering plant growth. Moreover, under low-Fe conditions, LPRs were preferentially induced in old leaves, but the loss of LPRs increased Fe deposition in the vasculature of older leaves and impeded Fe allocation to younger leaves. Therefore, disruption of both LPRs resulted in severer chlorosis in young leaves under Fe-deficient conditions. Taken together, the oxidation of Fe(II) to Fe(III) by LPRs in the cell wall of vasculature plays an important role in xylem Fe allocation, ensuring healthy Fe homeostasis for normal plant growth.

The protective role of FTY720 in promoting survival of allograft fat in mice.

Fat transplantation is widely used for soft-tissue filling and wound repair. Owing to the biological changes in adipocytes in some metabolic diseases, allograft fat can provide a better source of donor fat than autologous fat. Fingolimod (FTY720) possesses a powerful immunomodulatory function. This study aimed to investigate the protective effect of FTY720 in allogeneic fat transplantation. C57BL/6J mice that received allografts were randomly divided into two groups and treated with saline and FTY720, respectively. Fat graft samples were obtained at 1, 6, and 20 weeks posttransplantation. Graft volumes, graft structure, and immune cells were estimated using histological examination, immunohistochemistry, staining immunofluorescence (IF), and quantitative real-time polymerase chain reaction (qRT-PCR). Inflammatory cytokine mRNA expression in grafts was detected by qRT-PCR. FTY720 treatment significantly enhanced allograft retention, structural integrity, and neovascularization, thereby demonstrating the potential of FTY720 in improving graft survival. Further IF staining showed that FTY720 increased regulatory T cell infiltration and reduced macrophage infiltration to some extent. FTY720 treatment also enhanced the expression of the anti-inflammatory cytokines interleukin (IL)-4 and IL-10 and weakened the expression of the pro-inflammatory cytokines TNF-α and IL-6. Furthermore, FTY720 treatment upregulated the expression of CD31 positive cells. This study demonstrated the potential efficacy of FTY720 in improving the graft survival rate of syngeneic fat allograft models, possibly by suppressing immune rejection and promoting angiogenesis. Therefore, this study offers key insights into the potential application of a drug-assisted strategy to prolong allograft fat survival.

Transcatheter Angiographic Embolization of Percutaneous Nephrolithotomy-Related Bleeding: A Single-Center Experience.

Background: To evaluate the clinical characteristics and angiographic features of transcatheter angiographic embolization (TAE) in patients with active bleeding after percutaneous nephrolithotomy (PCNL). Methods: Between 2009 and 2018, 45 patients who underwent TAE for hemorrhage control after PCNL were reviewed retrospectively. Patient clinical characteristics and angiographic features of TAE were analyzed. Results: Of the 3148 patients, 45 (1.4%) patients were treated with TAE after PCNL. The interval from the bleeding episode to TAE was 3 days (1,6). Arterial laceration, arteriovenous fistula, and negative angiographic finding were found in 28 (62.2%), 7 (15.6%), and 10 patients (22.2%). Thirty-five patients (92.1%) achieved primary clinical success. The median-corrected hemoglobin decrease from bleeding episode to TAE was 52 g/L (25.25, 71.00). The median-corrected hemoglobin decrease rate from bleeding episode to TAE was 13.11 g/L·d (5.60, 26.12). The hemoglobin decrease from bleeding episode to TAE was lesser in negative angiographic patients (28.50 (10.75,51.25) g/L VS 53.7 (35.0,73.13) g/L) than in positive angiographic patients (P < 0.05). Conclusions: TAE is a safe and effective treatment for post-PCNL bleeding patients. Previous kidney surgery is associated with a higher risk of TAE. Patients with bleeding from multiple negative angiographic findings can be considered for prophylactic embolization.

Activation of peroxydisulfate via photothermal synergistic strategy for wastewater treatment: Efficiency and mechanism.

Peroxydisulfate (PDS)-based advanced oxidation processes (AOPs) have been demonstrated to be an effective technology for the removal of refractory organic contaminants from the aquatic environment. Herein, a photothermal synergistic strategy is developed to realize the green activation of PDS under solar light irradiation. An innovative solar photothermal reaction system and its corresponding evaluation method are established. The results show that there is a synergistic effect between light and light-generated thermal effects on the activation of PDS for effectively removing fulvic acid (FA). The maximum degradation percentage of FA increases from 42.6% to 90.8% after introducing ZrC nanoparticles as photothermal materials. The maximum temperature of the whole system is up to 66.4 â„ƒ after 120 min irradiation at 0.007 wt% solid content of ZrC, which is higher by 26.9% compared with that in the absence of ZrC nanoparticles. Furthermore, the underlying mechanism and PDS activation efficiency are deeply investigated. This work provides a viable strategy for directly using solar radiation to activate PDS for degrading refractory organic compounds, which creates a new avenue toward the utilization of solar energy for wastewater treatment.

Tobacco smoking and solid fuels for cooking and risk of liver cancer: A prospective cohort study of 0.5 million Chinese adults.

Previous research found tobacco smoking and solid fuel use for cooking to increase the risk of chronic liver disease mortality, but previous cohort studies have not investigated their independent and joint associations with liver cancer incidence in contemporary China. The China Kadoorie Biobank (CKB) study recruited 0.5 million adults aged 30 to 79 years from 10 areas across China during 2004 to 2008. Participants reported detailed smoking and fuel use information at baseline. After an 11.1-year median follow-up via electronic record linkage, we recorded 2997 liver cancer cases. Overall, 29.4% participants were current smokers. Among those who cooked at least once per month, 48.8% always used solid fuels (ie, coal or wood) for cooking. Tobacco smoking and solid fuel use for cooking were independently associated with increased risks of liver cancer, with hazard ratios (95% confidence intervals [CIs]) of 1.28 (1.15-1.42) and 1.25 (1.03-1.52), respectively. The more cigarettes consumed each day, the earlier the age of starting smoking or the longer duration of solid fuels exposure, the higher the risk (Ptrend < .001, =.001, =.018, respectively). Compared with never smokers who had always used clean fuels (ie, gas or electricity), ever-smokers who had always used solid fuels for cooking had a 67% (95% CIs: 1.29-2.17) higher risk. Among Chinese adults, tobacco smoking and solid fuel use for cooking were independently associated with higher risk of liver cancer incidence. Stronger association was observed with higher number of daily cigarette consumption, the earlier age of starting smoking and longer duration of solid fuel use.