Biogenic sulfur recovery from sulfate-laden antibiotic production wastewater using a single-chamber up-flow bioelectrochemical reactor.

The high-concentration sulfate (SO42-) in the antibiotic production wastewater hinders the anerobic methanogenic process and also proposes possible environmental risk. In this study, a novel single-chamber up-flow anaerobic bioelectrochemical reactor (UBER) was designed to realize simultaneous SO42- removal and elemental sulfur (S0) recovery. With the carbon felt, the cathode was installed underneath and the anode above to meet the different biological niches for sulfate reducing bacteria (SRB) and sulfur oxidizing bacteria (SOB). The bio-anode UBER (B-UBER) demonstrated a much higher average SO42- removal rate (SRR) of 113.2 ± 5.7 mg SO42--S L-1 d-1 coupled with a S0 production rate (SPR) of 54.4 ± 5.8 mg S0-S L-1 d-1 at the optimal voltage of 0.8 V than that in the abio-anode UBER (control reactor) (SRR = 86.6 ± 13.4 mg SO42--S L-1 d-1; SPR = 25.5 ± 9.7 mg S0-S L-1 d-1) under long-term operation. A large amount of biogenic S0 (about 72.2 mg g-1 VSS) was recovered in the B-UBER. The bio-anode, dominated by Thiovirga (SOB genus) and Acinetobacter (electrochemically active bacteria genus), exhibited a higher current density, lower overpotential, and lower internal resistance. C-type cytochromes mainly served as the crucial electron transfer mediator for both direct and indirect electron transfer, so that significantly increasing electron transfer capacity and biogenic S0 recovery. The reaction pathways of the sulfur transformation in the B-UBER were hypothesized that SRB utilized acetate as the main electron donor for SO42- reduction in the cathode zone and SOB transferred electrons to the anode or oxygen to produce biogenic S0 in the anode zone. This study proved a new pathway for biogenic S0 recovery and sulfate removal from sulfate-laden antibiotic production wastewater using a well-designed single-chamber bioelectrochemical reactor.

Pseudodonghicola flavimaris sp. nov. and Sedimentitalea xiamensis sp. nov., two novel species belonging to the family Roseobacteraceae.

Two Gram-stain-negative, chemoheterotrophic, aerobic bacteria, designated IC7T and JM2-8T, were isolated from seawater of the Yellow Sea of China and rhizosphere soil of mangroves in Xiamen, Fujian, respectively. Phylogenetic analyses based on 16S rRNA gene and genome sequences showed that these two novel strains belonged to the family Roseobacteraceae. Strain IC7T formed a coherent lineage within the genus Pseudodonghicola, showing 98.05 % 16S rRNA gene sequence similarity to Pseudodonghicola xiamenensis Y-2T. Strain JM2-8T was most closely related to members of the genus Sedimentitalea, showing 96.51 and 96.73 % 16S rRNA gene sequence similarities to Sedimentitalea nanhaiensis NH52FT and Sedimentitalea todarodis KHS03T, respectively. The two novel strains contained Q-10 as the major quinone, and phosphatidylethanolamine, aminophospholipid, phosphatidylglycerol and phosphatidylcholine as the principal polar lipids. The main fatty acid of strain IC7T was C19 : 0 cyclo ω8c, while the fatty acid profile JM2-8T was dominated by summed feature 8 containing C18 : 1 ω7c and/or C18 : 1 ω6c. The average nucleotide identity and digital DNA-DNA hybridization values between these two novel isolates and their closely related species were below the cut-off values of 95-96 and 70 %, respectively. The combined genotypic and phenotypic data show that strain IC7T represents a novel species of the genus Pseudodonghicola, for which the name Pseudodonghicola flavimaris sp. nov. is proposed, with the type strain IC7T (=MCCC 1A02763T=KCTC 82844T), and strain JM2-8T represents a novel species of the genus Sedimentitalea, for which the name Sedimentitalea xiamensis sp. nov. is proposed, with the type strain JM2-8T (=MCCC 1A17756T=KCTC 82846T).

Pseudophaeobacter profundi sp. nov., isolated from the Western Pacific Ocean.

A novel Gram-stain-negative, facultatively anaerobic and heterotrophic bacterium, designated strain ZH257T, was isolated from in situ enrichment samples incubated on the seamount floor of the Western Pacific Ocean. Cells were rod-shaped, oxidase- and catalase- positive, and motile by means of polar flagella. Strain ZH257T grew at 4-37 °C (optimum, 28-32 °C), pH 6.0-9.0 (optimum, pH 7.0) and with 2.0-9.0 % (w/v) NaCl (optimum, 3.0-4.0 %). Strain ZH257T was most closely related to members of the genus Pseudophaeobacter, sharing 99.13, 98.27 and 96.89 % 16S rRNA gene sequence identities with Pseudophaeobacter flagellatus GDMCC 1.2988T, Pseudophaeobacter arcticus DSM 23566T and Pseudophaeobacter leonis DSM 25627T, respectively. The DNA G+C content was 59.2 mol%. The estimated average nucleotide identity and digital DNA-DNA hybridization values between strain ZH257T and its closely related species were 79.61-93.04 % and 23.10-50.20 %, respectively. Strain ZH257T harboured complete denitrification and nitrate assimilation pathways. Strain ZH257T contained summed feature 8 (C18 : 1 ω7c and/or C18 : 1 ω6c) as major fatty acids (>5 %), and Q-10 as the major respiratory quinone. The polar lipid profile contained phosphatidylethanolamine, phosphatidylglycerol, phosphatidylcholine, diphosphatidylglycerol, an unidentified phospholipid, an unidentified aminolipid and four unidentified lipids. The combined phenotypic, genotypic and chemotaxonomic data showed that strain ZH257T represents a novel species of the genus Pseudophaeobacter, for which the name Pseudophaeobacter profundi sp. nov. is proposed, with the type strain ZH257T (=MCCC M29024T=KACC 23147T).

One-Pot Synthesis of Melamine Formaldehyde Resin-Derived N-Doped Porous Carbon for CO2 Capture Application.

The design and synthesis of porous carbons for CO2 adsorption have attracted tremendous interest owing to the ever-soaring concerns regarding climate change and global warming. Herein, for the first time, nitrogen-rich porous carbon was prepared with chemical activation (KOH) of commercial melamine formaldehyde resin (MF) in a single step. It has been shown that the porosity parameters of the as-prepared carbons were successfully tuned by controlling the activating temperature and adjusting the amount of KOH. Thus, as-prepared N-rich porous carbon shows a large surface area of 1658 m2/g and a high N content of 16.07 wt%. Benefiting from the unique physical and textural features, the optimal sample depicted a CO2 uptake of up to 4.95 and 3.30 mmol/g at 0 and 25 °C under 1 bar of pressure. More importantly, as-prepared adsorbents show great CO2 selectivity over N2 and outstanding recyclability, which was prominently important for CO2 capture from the flue gases in practical application. An in-depth analysis illustrated that the synergetic effect of textural properties and surface nitrogen decoration mainly determined the CO2 capture performance. However, the textural properties of carbons play a more important role than surface functionalities in deciding CO2 uptake. In view of cost-effective synthesis, outstanding textural activity, and the high adsorption capacity together with good selectivity, this advanced approach becomes valid and convenient in fabricating a unique highly efficient N-rich carbon adsorbent for CO2 uptake and separation from flue gases.

One-Pot Synthesis of N-Rich Porous Carbon for Efficient CO2 Adsorption Performance.

N-enriched porous carbons have played an important part in CO2 adsorption application thanks to their abundant porosity, high stability and tailorable surface properties while still suffering from a non-efficient and high-cost synthesis method. Herein, a series of N-doped porous carbons were prepared by a facile one-pot KOH activating strategy from commercial urea formaldehyde resin (UF). The textural properties and nitrogen content of the N-doped carbons were carefully controlled by the activating temperature and KOH/UF mass ratios. As-prepared N-doped carbons show 3D block-shaped morphology, the BET surface area of up to 980 m2/g together with a pore volume of 0.52 cm3/g and N content of 23.51 wt%. The optimal adsorbent (UFK-600-0.2) presents a high CO2 uptake capacity of 4.03 mmol/g at 0 °C and 1 bar. Moreover, as-prepared N-doped carbon adsorbents show moderate isosteric heat of adsorption (43-53 kJ/mol), acceptable ideal adsorption solution theory (IAST) selectivity of 35 and outstanding recycling performance. It has been pointed out that while the CO2 uptake was mostly dependent on the textural feature, the N content of carbon also plays a critical role to define the CO2 adsorption performance. The present study delivers favorable N-doped carbon for CO2 uptake and provides a promising strategy for the design and synthesis of the carbon adsorbents.

Dietary zero-dimensional fullerene supplementation improves the meat quality, lipid metabolism, muscle fiber characteristics, and antioxidative status in finishing pigs.

With the increasing demand for high-quality pork, more nutritional substances have been studied for the regulation of meat quality. Zero-dimensional fullerenes (C60) can modulate the biological behavior of a variety of cell lines and animals. In this study, we report the biological effects of C60 on finishing pigs at different concentrations. A total of 24 barrows (Duroc × Large White × Landrace), with an average body weight of 21.01 ± 0.98 kg, were divided into 3 groups and each treated daily with C60 (100 or 200 mg per kg feed) or a control diet until the end of the experiment. Our results showed that dietary C60 supplementation improved flesh color, marbling scores, and flavor amino acid contents of longissimus dorsi (LD) of growing-finishing pigs (P < 0.05). C60 improved meat quality by regulating lipid metabolism and muscle fiber morphology by mediating the expression of genes, L-lactic dehydrogenase (LDH), myosin heavy chain (MyHC) IIa, MyHCIIb, peroxisome proliferator-activated receptor γ (PPARγ), and fatty acid transport protein 1 (FATP1) (P < 0.05). Moreover, C60 substantially promoted the mRNA expression of antioxidant enzyme genes (P < 0.05), which also contributed to improving meat quality. These findings have important implications for the application of C60 in the livestock industry, especially for improving the meat quality of fattening pigs.

Stress responses of sulfate-reducing bacteria sludge upon exposure to polyethylene microplastics.

The stress responses of sulfate-reducing bacteria (SRB) sludge to polyethylene (PE) microplastic exposure were revealed for the first time. In this study, a lab-scale sulfate-reducing up-flow sludge bed reactor was continuously operated with different concentrations of PE microplastics in the feed (20, 100, and 500 microplastic particles (MPs)/L). Exposure to low levels of PE microplastics (i.e., 20 MPs/L) had a limited effect on SRB consortia, whereas higher levels of PE microplastics imposed apparent physiological stresses on SRB consortia. Despite this, the overall reactor performance, i.e., chemical oxygen demand removal and sulfate conversion, was less affected by prolonged exposure to PE microplastics. Moreover, as the concentration of PE microplastics increased, the SRB consortia promoted the production of extracellular polymeric substances to a greater extent, especially the secretion of proteins. As a result, protective effects against the cytotoxicity of PE microplastics were provided. Batch experiments further demonstrated that leaching additives from PE microplastics (including acetyl tri-n­butyl citrate and bisphenol A, concentrations up to 5 µg/g sludge) exerted only a minor effect on the activity of SRB consortia. Additionally, microbial community analysis revealed active and potentially efficient sulfate reducers at different operational stages. Our results provide insight into the stress responses of SRB sludge under PE microplastic exposure and suggested that SRB consortia can gradually adapt to and resist high levels of PE microplastics. These findings may promote a better understanding of the stable operation of SRB sludge systems under specific environmental stimuli for practical applications.

Numerical investigation of microchannel geometry for effective on-chip biofluid delivery by AC electrothermal effect.

Although there exist tremendous needs for on-chip biofluid delivery, research in this field has yielded limited numbers of devices for real-world applications. One challenge is the difficulty for micropumps to meet the requirements of being low cost to fabricate, easy to integrate and effective for intended applications at the same time. This research focuses on AC electrothermal (ACET) micropumps based on planar interdigitated electrodes, due to their practicality in fabrication and operation, and compatibility with biochemical fluids. Our prior work has optimized the design of electrode dimensions for a fixed microchannel design. This work finds that microchannel dimensions can also affect ACET micropumps significantly, with respect to flow rate and electric impedance loading. This work first considers the constraints arising from impedance loading by ACET micropumps on power supplies, then the investigation describes several key parameters (threshold height, saturation thickness), to arrive at an appropriate microchannel geometry for the effective delivery of biofluids. The optimized microchannel is expected to incorporate well into a multifunctional lab-chip system to transport biofluids efficiently.

Rapid and Sensitive Detection of miRNA Based on AC Electrokinetic Capacitive Sensing for Point-of-Care Applications.

A sensitive and efficient method for microRNAs (miRNAs) detection is strongly desired by clinicians and, in recent years, the search for such a method has drawn much attention. There has been significant interest in using miRNA as biomarkers for multiple diseases and conditions in clinical diagnostics. Presently, most miRNA detection methods suffer from drawbacks, e.g., low sensitivity, long assay time, expensive equipment, trained personnel, or unsuitability for point-of-care. New methodologies are needed to overcome these limitations to allow rapid, sensitive, low-cost, easy-to-use, and portable methods for miRNA detection at the point of care. In this work, to overcome these shortcomings, we integrated capacitive sensing and alternating current electrokinetic effects to detect specific miRNA-16b molecules, as a model, with the limit of detection reaching 1.0 femto molar (fM) levels. The specificity of the sensor was verified by testing miRNA-25, which has the same length as miRNA-16b. The sensor we developed demonstrated significant improvements in sensitivity, response time and cost over other miRNA detection methods, and has application potential at point-of-care.

Fullerene C60 Protects Against Intestinal Injury from Deoxynivalenol Toxicity by Improving Antioxidant Capacity.

Oxidative stress is involved in a wide variety of pathologies, and fullerene has been shown to have an antioxidant ability. Mycotoxins exert toxic effects through induction of excessive reactive oxygen species (ROS). Here, we evaluated water-soluble fullerene C60 for its anti-mycotoxin and antioxidant effects in vitro and in vivo. Intestinal epithelial cells were cultured with fullerene during deoxynivalenol (DON) exposure. The results revealed that fullerene C60 significantly promoted cell viability, decreased apoptosis and necrotic cell number, and significantly reduced intracellular ROS levels during DON exposure (p < 0.05). To investigate the role of fullerene in antioxidant capacity in vivo further, 40 three-week-old male C57BL/6 mice were randomly divided into four groups. There were no significant differences between the control and fullerene groups (p > 0.05). In mice exposed to DON, supplementation with fullerene C60 significantly improved growth performance, and enhanced the total antioxidant status and the activities of SOD and GPX in the intestine and liver (p < 0.05). In addition, fullerene C60 supplementation improved intestinal morphology, as indicated by a higher villus height and tight junction protein expression (p < 0.05). Furthermore, fullerene supplementation decreased serum concentrations of inflammatory cytokine and lipopolysaccharide (LPS; a penetrability marker) compared to the DON-challenged group (p < 0.05). The current study suggests that fullerene C60 improves intestinal antioxidant status against DON-induced oxidative stress in vitro and in vivo.

Deciphering the succession dynamics of dominant and rare genera in biofilm development process.

Deciphering the succession dynamics of dominant and rare taxa is crucial to understand the stability and ecosystem functions of biofilm communities. However, the essential laws of the succession dynamics based on dominant and rare taxa were still unenlightened. Herein, we investigated the succession dynamics of dominant and rare genera in multi-species biofilms developed in flow cells fed with 10 and 40 mg-TOC/L LB broth. The relative abundance of dominant genera (Enterobacteria and Acinetobacter) decreased remarkably (from 94.63% to 73.22%) in 10 mg-TOC/L LB broth, whereas they kept relatively steady (93.75 ± 4.23%) along with the cultivation time in 40 mg-TOC/L LB broth. Fluorescence in situ hybridization showed that rare genera tended to form clusters at both concentrations, while weaker dispersal of dominant genera caused patchier biofilm structures in 10 mg-TOC/L LB broth compared to that in 40 mg-TOC/L LB broth. Null model analyses further demonstrated that the stochastic ecological drift was more pronounced in the community assembly of biofilms in 10 mg-TOC/L LB broth (73.33%) than those in 40 mg-TOC/L LB broth (60.95%), weakening the competitive superiority of dominant taxa in the patchier biofilms. In addition, the co-occurrence network reflected that the positive interactions among rare genera contributed to exclude dominant genera in 10 mg-TOC/L LB broth, whereas negative interactions only occurred between the dominant Enterobacter and Acinetobacter or rare Comamonas in 40 mg-TOC/L LB broth. This study highlighted the distinctive succession dynamics of dominant and rare genera in biofilms at different substrate concentrations, which would advance our understanding of the biofilm communities in biofilm-related process.

Oenological characteristics, amino acids and volatile profiles of Hongqu rice wines during pottery storage: Effects of high hydrostatic pressure processing.

Hongqu rice wines were subjected to high hydrostatic pressure (HHP) treatments of 200 MPa and 550 MPa at 25 °C for 30 min and effects on wine quality during pottery storage were examined. HHP treatment can significantly (p<0.05) decrease the content of fusel-like alcohols and maintain the concentration of lactones in these wines. After 18 months of storage, the HHP-treated wines exhibited a more rapid decrease in total sugars (9.3-15.3%), lower free amino acid content (e.g. lysine content decreased by 45.0-84.5%), and higher ketone content (e.g. 6- and 14-fold increase for 2-nonanone). These changes could be attributed to the occurrence of Maillard and oxidation reactions. The wines treated at 550 MPa for 30 min developed about twice as rapidly during pottery storage than untreated wines based on principal component analysis. After only 6 months, treated wines had a volatile composition and an organoleptic quality similar to that of untreated wines stored in pottery for 18 months.

Chitosan-based nanoparticles for improved anticancer efficacy and bioavailability of mifepristone.

In addition to its well-known abortifacient effect, mifepristone (MIF) has been used as an anticancer drug for various cancers in many studies with an in-depth understanding of the mechanism of action. However, application of MIF is limited by its poor water solubility and low oral bioavailability. In this work, we developed a drug delivery system based on chitosan nanoparticles (CNs) to improve its bioavailability and anticancer activity. The MIF-loaded chitosan nanoparticles (MCNs) were prepared by convenient ionic gelation techniques between chitosan (Cs) and tripolyphosphate (TPP). The preparation conditions, including Cs concentration, TPP concentration, Cs/MIF mass ratio, and pH value of the TPP solution, were optimized to gain better encapsulation efficiency (EE) and drug loading capacity (DL). MCNs prepared with the optimum conditions resulted in spherical particles with an average size of 200 nm. FTIR and XRD spectra verified that MIF was successfully encapsulated in CNs. The EE and DL of MCNs determined by HPLC were 86.6% and 43.3%, respectively. The in vitro release kinetics demonstrated that MIF was released from CNs in a sustained-release manner. Compared with free MIF, MCNs demonstrated increased anticancer activity in several cancer cell lines. Pharmacokinetic studies in male rats that were orally administered MCNs showed a 3.2-fold increase in the area under the curve from 0 to 24 h compared with free MIF. These results demonstrated that MCNs could be developed as a potential delivery system for MIF to improve its anticancer activity and bioavailability.