A Simple and Effective Phosphine-Doping Technique for Solution-Processed Nanocrystal Solar Cells.

Solution-processed cadmium telluride (CdTe) nanocrystal (NC) solar cells offer the advantages of low cost, low consumption of materials and large-scale production via a roll-to-roll manufacture process. Undecorated CdTe NC solar cells, however, tend to show inferior performance due to the abundant crystal boundaries within the active CdTe NC layer. The introduction of hole transport layer (HTL) is effective for promoting the performance of CdTe NC solar cells. Although high-performance CdTe NC solar cells have been realized by adopting organic HTLs, the contact resistance between active layer and the electrode is still a large problem due to the parasitic resistance of HTLs. Here, we developed a simple phosphine-doping technique via a solution process under ambient conditions using triphenylphosphine (TPP) as a phosphine source. This doping technique effectively promoted the power conversion efficiency (PCE) of devices to 5.41% and enabled the device to have extraordinary stability, showing a superior performance compared with the control device. Characterizations suggested that the introduction of the phosphine dopant led to higher carrier concentration, hole mobility and a longer lifetime of the carriers. Our work presents a new and simple phosphine-doping strategy for further improving the performance of CdTe NC solar cells.

Efficient Nanocrystal Photovoltaics with PTAA as Hole Transport Layer.

The power conversion efficiency (PCE) of solution-processed CdTe nanocrystals (NCs) solar cells has been significantly promoted in recent years due to the optimization of device design by advanced interface engineering techniques. However, further development of CdTe NC solar cells is still limited by the low open-circuit voltage (Voc) (mostly in range of 0.5-0.7 V), which is mainly attributed to the charge recombination at the CdTe/electrode interface. Herein, we demonstrate a high-efficiency CdTe NCs solar cell by using organic polymer poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA) as the hole transport layer (HTL) to decrease the interface recombination and enhance the Voc. The solar cell with the architecture of ITO/ZnO/CdS/CdSe/CdTe/PTAA/Au was fabricated via a layer-by-layer solution process. Experimental results show that PTAA offers better back contact for reducing interface resistance than the device without HTL. It is found that a dipole layer is produced between the CdTe NC thin film and the back contact electrode; thus the built-in electric field (Vbi) is reinforced, allowing more efficient carrier separation. By introducing the PTAA HTL in the device, the open-circuit voltage, short-circuit current density and the fill factor are simultaneously improved, leading to a high PCE of 6.95%, which is increased by 30% compared to that of the control device without HTL (5.3%). This work suggests that the widely used PTAA is preferred as the excellent HTL for achieving highly efficient CdTe NC solar cells.

Efficient Nanocrystal Photovoltaics via Blade Coating Active Layer.

CdTe semiconductor nanocrystal (NC) solar cells have attracted much attention in recent year due to their low-cost solution fabrication process. However, there are still few reports about the fabrication of large area NC solar cells under ambient conditions. Aiming to push CdTe NC solar cells one step forward to the industry, this study used a novel blade coating technique to fabricate CdTe NC solar cells with different areas (0.16, 0.3, 0.5 cm2) under ambient conditions. By optimizing the deposition parameters of the CdTe NC's active layer, the power conversion efficiency (PCE) of NC solar cells showed a large improvement. Compared to the conventional spin-coated device, a lower post-treatment temperature is required by blade coated NC solar cells. Under the optimal deposition conditions, the NC solar cells with 0.16, 0.3, and 0.5 cm2 areas exhibited PCEs of 3.58, 2.82, and 1.93%, respectively. More importantly, the NC solar cells fabricated via the blading technique showed high stability where almost no efficiency degradation appeared after keeping the devices under ambient conditions for over 18 days. This is promising for low-cost, roll-by-roll, and large area industrial fabrication.

Analysis of microbial community composition and diversity in postoperative intracranial infection using high­throughput sequencing.

Intracranial infection is one of the most serious complications following neurosurgery. It is well acknowledged that bacteria and fungi are the main pathogens responsible for postoperative intracranial infection. However, the microbial community structure, including composition, abundance and diversity, in postoperative intracranial infection is not fully understood, which greatly compromises our understanding of the necessity and effectiveness of postoperative antibiotic treatment. The present study collected eight cerebrospinal fluid (CSF) samples from patients with intracranial infection following neurosurgical procedures. High­throughput amplicon sequencing for 16S rDNA and internal transcribed spacer (ITS) was performed using the Illumina MiSeq platform to investigate the microbial community composition and diversity between treated and untreated patients. Bioinformatics analysis revealed that the microbial composition and diversity in each patient group (that is, with or without antibiotic treatment) was similar; however, the group receiving antibiotic treatment had a comparatively lower species abundance and diversity compared with untreated patients. At the genus level, Acinetobacter and Staphylococcus were widely distributed in CSF samples from patients with postoperative intracranial infection; in particular, Acinetobacter was detected in all CSF samples. In addition, five ITS fungal libraries were constructed, and Candida was detected in three out of four patients not receiving antibiotic treatment, indicating that the fungal infection should be given more attention. In summary, 16S and ITS high­throughput amplicon sequencing were practical methods to identify pathogens in the different periods of treatment in patients with postoperative intracranial infection. There was a notable difference in microbial composition and diversity between the treated and untreated patients. Alterations in the microbial community structure may provide a signal whether antibiotic treatment worked in postoperative intracranial infection and may assist surgeons to better control the progression of infection.