Long-term chronic food-derived arsenic exposure induce the urinary system metabolic dysfunction in mice.

The consumption of rice contaminated with arsenic on a long-term basis has emerged as a pressing public health issue of global significance. Arsenic-induced urinary injury, particularly kidney damage, has received widespread attention. In this study, mice model under long-term arsenic exposure was established, mouse were exposed to rice arsenic (30 mg/kg) for 14 months. Changes of related metabolites were observed based on kidney metabolomics and lipidomics, and major biomarkers were screened by urine metabolomics. The results showed that phosphatidylethanolamine (PE) was significantly increased and phosphatidycholine (PC) and phosphatidylglycerol (PG) were significantly reduced after arsenic exposure, leading to related downstream lipid metabolism disorders. The metabolic pathways for amino acid and energy were observed to be impacted. In addition, metabolic disorders due to arsenic exposure may be associated with inherited neurometabolic disorders, such as D-2-hydroxyglutaric aciduria (D-2-HGA), and pyruvate carboxylase deficiency (PCD), which is predicted based on significant difference biomarkers (2-oxoglutarate, malic acid, and succinic acid) screened for urine. This study elucidates the mechanism of toxicity in the urinary system induced by arsenic exposure at nearly half life cycle, which furnishes crucial scientific evidence pertaining to the toxicity and risk evaluation associated with chronic exposure to the arsenic.

Construction of electrochemical sensing interface towards Cd(II) based on activated g-C3N4 nanosheets: considering the effects of exfoliation and protonation treatment.

There is an urgent need to construct highly selective low-cost sensors for fast detection of toxic metal ions such as cadmium. When compared with 3D bulk materials, 2D layered materials after activation treatments show superior performances for electrochemical metal ion detection. The bulk graphitic carbon nitride (hereafter b-g-C3N4) was prepared by thermal polymerization with urea as a precursor; it was then activated through ultrasonic liquid exfoliation and protonation which resulted in successful fabrication of activated ultrathin g-C3N4 nanosheets (hereafter a-g-C3N4). The a-g-C3N4-modified glassy carbon electrode demonstrates excellent electrochemical performances for Cd2+ detection with 22.668 µA/µM sensitivity and 3.9 nM LOD (S/N = 3) due to high specific surface area and active sites created on the 2D layered structure. The chemical interference of Pb2+, Cu2+, and Hg2+ on Cd2+ detection was minimal. We have also measured Cd2+ in natural water and rice samples using the newly developed a-g-C3N4-modified electrode with high spike recoveries. Our results demonstrate the potential applications of newly developed a-g-C3N4-modified electrode for rapid detection of toxic metal ions in different sample matrixes. Graphical Abstract The activated g-C3N4 nanosheets (a-g-C3N4) were synthesized and used to construct electrochemical sensors with high sensitivity and anti-interference performance.

Metallic Contact between MoS2 and Ni via Au Nanoglue.

A critical factor for electronics based on inorganic layered crystals stems from the electrical contact mode between the semiconducting crystals and the metal counterparts in the electric circuit. Here, a materials tailoring strategy via nanocomposite decoration is carried out to reach metallic contact between MoS2 matrix and transition metal nanoparticles. Nickel nanoparticles (NiNPs) are successfully joined to the sides of a layered MoS2 crystal through gold nanobuffers, forming semiconducting and magnetic NiNPs@MoS2 complexes. The intrinsic semiconducting property of MoS2 remains unchanged, and it can be lowered to only few layers. Chemical bonding of the Ni to the MoS2 host is verified by synchrotron radiation based photoemission electron microscopy, and further proved by first-principles calculations. Following the system's band alignment, new electron migration channels between metal and the semiconducting side contribute to the metallic contact mechanism, while semiconductor-metal heterojunctions enhance the photocatalytic ability.

Nanosecond laser coloration on stainless steel surface.

In this work, we present laser coloration on 304 stainless steel using nanosecond laser. Surface modifications are tuned by adjusting laser parameters of scanning speed, repetition rate, and pulse width. A comprehensive study of the physical mechanism leading to the appearance is presented. Microscopic patterns are measured and employed as input to simulate light-matter interferences, while chemical states and crystal structures of composites to figure out intrinsic colors. Quantitative analysis clarifies the final colors and RGB values are the combinations of structural colors and intrinsic colors from the oxidized pigments, with the latter dominating. Therefore, the engineering and scientific insights of nanosecond laser coloration highlight large-scale utilization of the present route for colorful and resistant steels.

Magnetic MoS2 pizzas and sandwiches with Mnn (n = 1-4) cluster toppings and fillings: A first-principles investigation.

The inorganic layered crystal (ILC) MoS2 in low dimensions is considered as one of the most promising and efficient semiconductors. To enable the magnetism and keep intrinsic crystal structures, we carried out a first-principles study of the magnetic and semiconductive monolayer MoS2 adsorbed with the Mnn (n = 1-4) clusters, and bilayer MoS2 intercalated with the same clusters. Geometric optimizations of the Mnn@MoS2 systems show the complexes prefer to have Mnn@MoS2(M) pizza and Mnn@MoS2(B) sandwich forms in the mono- and bi-layered cases, respectively. Introductions of the clusters will enhance complex stabilities, while bonds and charge transfers are found between external Mn clusters and the S atoms in the hosts. The pizzas have medium magnetic moments of 3, 6, 9, 4 µB and sandwiches of 3, 2, 3, 2 µB following the manganese numbers. The pizzas and sandwiches are semiconductors, but with narrower bandgaps compared to their corresponding pristine hosts. Direct bandgaps were found in the Mnn@MoS2(M) (n = 1,4) pizzas, and excitingly in the Mn1@MoS2(B) sandwich. Combining functional clusters to the layered hosts, the present work shows a novel material manipulation strategy to boost semiconductive ILCs applications in magnetics.

Replication of Leaf Surface Structures for Light Harvesting.

As one of the most important hosts of natural light harvesting, foliage normally has complicated surface structures to capture solar radiances. Bio-mimicking leaf surface structures can provide novel designs of covers in photovoltaic systems. In this article, we reported on replicating leaf surface structures on poly-(methyl methacrylate) polymers to prompt harvesting efficiencies. Prepared via a double transfer process, the polymers were found to have high optical transparencies and transmission hazes, with both values exceeding 80% in some species. Benefiting from optical properties and wrinkled surfaces, the biomimetic polymers brought up to 17% gains to photovoltaic efficiencies. Through Monte-Carlo simulations of light transport, ultrahigh haze values and low reflections were attributed to lightwave guidance schemes lead by the nano- and micro-morphologies which are inherited from master leaves. Thus, leaf surface bio-mimicking can be considered as a strategic direction to design covers of light harvesting systems.