The Effect of Conductive Additive Morphology and Crystallinity on the Electrochemical Performance of Ni-Rich Cathodes for Sulfide All-Solid-State Lithium-Ion Batteries.

Sulfide electrolyte all-solid-state lithium-ion batteries (ASSLBs) that have inherently nonflammable properties have improved greatly over the past decade. However, determining both the stable and functional electrode components to pair with these solid electrolytes requires significant investigation. Solid electrolyte comprises 20-40% of the composite cathode electrode, which improves the ionic conductivity. However, this results in thick electrolyte that blocks the electron pathways in the electrode, significantly lowering the electrochemical performance. The application of conductive carbon material is required to overcome this issue, and, hence, determining the carbon properties that result in the most stable performance in the sulfide solid electrolyte is vital. This study analyzes the effect of the cathode conductive additive's morphology on the electrochemical performance of sulfide electrolyte-based ASSLBs. Carbon black (CB) and carbon nanotubes (CNTs), which provide electron pathways at the nanoscale and sub-micron scale, and carbon nanofiber (CNF), which provides electron pathways at the tens-of-microns scale, are all tested individually as potential conductive additives. When the CNF, with its high crystallinity, is used as a conductive material, the electrochemical performance shows an excellent initial discharge capacity of 191.78 mAh/g and a 50-cycle capacity retention of 83.9%. Conversely, the CB and the CNTs, with their shorter pathways and significantly increased surface area, show a relatively low electrochemical performance. By using the CNF to provide excellent electrical conductivity to the electrode, the polarization is suppressed. Furthermore, the interfacial impedance across the charge transfer region is also reduced over 50 cycles compared with the CB and CNT composite cells. These findings stringently analyze and emphasize the importance of the morphology of the carbon conductive additives in the ASSLB cathode electrodes, with improvements in the electrochemical performance being realized through the application of long-form two-dimensional crystalline CNFs.

Exploring the Potential of a Thermionic LaB6 Virtual Source Mode Electron Gun for a High Angular Current Density and a Narrow Energy Distribution.

To date, lanthanum hexaboride (LaB6) thermionic electron sources have not been able fully to capitalize on their inherent potential, resulting in an ambiguous position within the application area. Although they exhibit higher brightness compared with a tungsten filament source, they still fall short of the performance of Schottky electron sources. This study aims to explore the capabilities of the LaB6 electron source under different operating conditions to bridge the gap, ultimately to realize its untapped potential. Simulations in virtual source mode indicated enhanced beam brightness and a reduced beam half-angle with an increase the extraction voltage, promising up to tenfold times higher beam brightness compared with the crossover mode. The energy distribution measured using a prelens retarding field energy analyzer revealed an energy distribution of 0.55 eV and a high angular current density of 33 mA/sr in the virtual source mode. Therefore, the virtual source mode of LaB6 can provide a narrow energy distribution akin to that of a ZrO/W Schottky electron gun (1600 K) while having an angular current density over 2,000 times higher. In addition, the stability of the virtual source mode is ±0.022%, while that of the crossover mode is ±0.138%.

Enhanced Scanning Electron Microscopy Using Auto-Optimized Image Restoration With Constrained Least Squares Filter for Nanoscience.

The growing demands of nanoscience require the continuous improvement of visualization methods. The imaging performance of scanning electron microscopy (SEM) is fundamentally limited by the point spread function of the electron beam and degrades because of noise. This paper proposes an auto-optimization algorithm based on deconvolution for the restoration of SEM images. This algorithm uses a constrained least squares filter and does not dependent on the user's experience or the availability of nondegraded images. The proposed algorithm improved the quality of the SEM images of 10-nm Au nanoparticles, and achieved balance among the sharpness, contrast-to-noise ratio (CNR), and image artifacts. For the SEM image of 100-nm pitched line patterns, the analysis of the spatial frequencies allowed the 2.5-fold improvement of the intensity of 4-nm information, and the noise floor decreased approximately 32 times. Along with the results obtained by the application of the proposed algorithm to images of tungsten disulfide (WS2) flakes, carbon nanotubes (CNTs), and HeLa cells, the evaluation results confirm that the proposed algorithm can enhance the SEM imaging of nanoscale features that lie close to the microscope's resolution limit.

High-Performance Compact Pre-Lens Retarding Field Energy Analyzer for Energy Distribution Measurements of an Electron Gun.

The energy distribution of an electron gun is one of the most important characteristics determining the performance of electron beam-based instruments, such as electron microscopes and electron energy loss spectroscopes. For accurate measurements of the energy distribution, this study presents a novel retarding field energy analyzer (RFEA) with the feature of an additional integrated pre-lens, which enables an adjustment of beam trajectory into the analyzer. The advantages of this analyzer are its compact size and simple electrode configuration. According to trajectory simulation theories, the optimum condition arises when the incident electron beam inside the RFEA is focused on the center of a retarding electrode. Comparing I­V curves depending on whether the pre-lens working or not, it is confirmed that the use of the pre-lens dramatically improves the energy resolution and efficiency of the signal acquisition process. The pre-lens RFEA was applied to characterize a Schottky electron gun under various temperatures and extraction voltages as operational conditions. When the tip temperature was increased by 50 K, we were able to measure an energy distribution broadening of 13.8 meV with the proposed pre-lens RFEA. The relative standard deviation of energy distribution was 0.7% for each working condition.

Study and design of a lens-type retarding field energy analyzer without a grid electrode.

A retarding field energy analyzer (RFEA) for measuring the energy distribution of charged particles offers the advantages of a simple structure and suitability for simultaneous observations of beam patterns in two dimensions. In this study, lens-based RFEAs without a grid electrode were theoretically investigated with regard to the geometry and lens condition to achieve high performance. The simulation results show that the proposed RFEA can achieve a resolution of 2.6 meV at an energy level of 500 eV. In addition, performance, which is the ratio of the resolution to the beam energy, reached 5.2×10-6. These results indicate that the RFEA designed in this study is capable of high-performance outcomes. The findings here demonstrate that the most important factors when attempting to realize a high-resolution RFEA design are to reduce the sagging effect of the electron beam through the focusing lens and ensure that V″(z) in the retarding electrode is close to zero. The design of the lens-based RFEAs is described in detail.

Absorption and desorption of SO2 in aqueous solutions of diamine-based molten salts.

SO2 absorption and desorption behaviors were investigated in aqueous solutions of diamine-derived molten salts with a tertiary amine group on the cation and a chloride anion, including butyl-(2-dimethylaminoethyl)-dimethylammonium chloride ([BTMEDA]Cl, pKb=8.2), 1-butyl-1,4-dimethylpiperazinium chloride ([BDMP]Cl, pKb=9.8), and 1-butyl-4-aza-1-azoniabicyclo[2,2,2]octane chloride ([BDABCO]Cl, pKb=11.1). The SO2 absorption and desorption performance of the molten salt were greatly affected by the basicity of the molten salt. Spectroscopic, X-ray crystallographic, and computational results for the interactions of SO2 with molten salts suggest that two types of SO2-containg species could be generated depending on the basicity of the unquaternized amino group: a dicationic species comprising two different anions, HSO3(-) and Cl(-), and a monocationic species bearing Cl(-) interacting with neutral H2SO3.