Assessing Microstructural, Biomechanical, and Biocompatible Properties of TiNb Alloys for Potential Use as Load-Bearing Implants.

Titanium-Niobium (TiNb) alloys are commonly employed in a number of implantable devices, yet concerns exist regarding their use in implantology owing to the biomechanical mismatch between the implant and the host tissue. Therefore, to balance the mechanical performance of the load-bearing implant with bone, TiNb alloys with differing porosities were fabricated by powder metallurgy combined with spacer material. Microstructures and phase constituents were characterized with energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The mechanical properties were tested by uniaxial compression, and the corrosion performance was determined via a potentiodynamic polarization experiment. To evaluate a highly matched potential implant with the host, biocompatibilities such as cell viability and proliferation rate, fibronectin adsorption, plasmid-DNA interaction, and an SEM micrograph showing the cell morphology were examined in detail. The results showed that the alloys displayed open and closed pores with a uniform pore size and distribution, which allowed for cell adherence and other cellular activities. The alloys with low porosity displayed compressive strength between 618 MPa and 1295 MPa, while the alloys with high porosity showed significantly lower strength, ranging from 48 MPa to 331 MPa. The biological evaluation of the alloys demonstrated good cell attachment and proliferation rates.

Microstructural, Biomechanical, and In Vitro Studies of Ti-Nb-Zr Alloys Fabricated by Powder Metallurgy.

This study investigated the microstructures, mechanical performances, corrosion resistances, and in vitro studies of porous Ti-xNb-10Zr (x: 10 and 20; at. %) alloys. The alloys were fabricated by powder metallurgy with two categories of porosities, i.e., 21-25% and 50-56%, respectively. The space holder technique was employed to generate the high porosities. Microstructural analysis was performed by using various methods including scanning electron microscopy, energy dispersive spectroscopy, electron backscatter diffraction, and x-ray diffraction. Corrosion resistance was assessed via electrochemical polarisation tests, while mechanical behavior was determined by uniaxial compressive tests. In vitro studies, such as cell viability and proliferation, adhesion potential, and genotoxicity, were examined by performing an MTT assay, fibronectin adsorption, and plasmid-DNA interaction assay. Experimental results showed that the alloys had a dual-phase microstructure composed of finely dispersed acicular hcp α-Ti needles in the bcc ß-Ti matrix. The ultimate compressive strength ranged from 1019 MPa to 767 MPa for alloys with 21-25% porosities and from 173 MPa to 78 MPa for alloys with 50-56% porosities. Noted that adding a space holder agent played a more critical role in the mechanical behaviors of the alloys compared to adding niobium. The pores were largely open and exhibited irregular shapes, with uniform size distribution, allowing for cell ingrowth. Histological analysis showed that the alloys studied met the biocompatibility criteria required for orthopaedic biomaterial use.

Mechanical properties and biodegradability of Mg-Zn-Ca alloys: homogenization heat treatment and hot rolling.

In this study, Mg was alloyed with Zn and Ca to produce six different Mg-Zn-Ca alloys (designated as ZX alloys) by the gravity die casting method. Zn contents of the alloys were 1 wt., 3 wt., and 5 wt.% and Ca contents of the alloys were 0.2 wt. and 1.8 wt.%. Homogenization heat treatment was applied to all cast alloys. After that, a part of each homogenization heat-treated alloys was hot-rolled. Microstructure, mechanical properties, electrochemical and immersion corrosion behaviors at simulated physiological conditions of the heat-treated and hot-rolled alloys were compared. Increasing the amount of alloying elements (Zn and Ca) in Mg reduces grain size and improves the hardness. It was seen that the microstructure consisted of α-Mg as a matrix phase and intermetallic phases: Mg2Ca phase for the alloy having Zn/Ca = 0.37 (ZX12) and Ca2Mg6Zn3 phase for the other alloys. When the mechanical properties and corrosion rates of homogenized and hot-rolled alloys were compared, it was seen that hot-rolled ZX10-h (Mg-0.94Zn-0.16Ca) alloy can be considered as a fracture bone fixation plate material with its acceptable properties: 121 ± 2.1 MPa yield strength, 226 ± 3.7 MPa tensile strength, % 4.1 ± 0.2 elongation, and 0.062 mm/year immersion corrosion rate.