A biomechanical shoulder strain index based on stabilizing demand of shoulder joint.

Work-related shoulder joint disorders contribute considerably to absenteeism in the workplace. To identify the tasks that are stressful to the shoulder joint, a strain index was formulated based on the concept of concavity compression-a shoulder stabilizing mechanism. The magnitude and direction of the shoulder joint reaction forces were used in formulating the strain index. A two phase experiment was conducted. In Phase 1, participants performed 30 different manual handling tasks. The tasks were categorized into low, medium and high strain tasks based on their strain index values. In Phase 2, out of the 30 tasks, repetitive exertions of three tasks (low, medium and high strain index values) were simulated using three external loads (0.91, 1.81 and 2.72 kg). The muscle activity data recorded from eight shoulder muscles showed that tasks with higher strain index values induced significantly greater activation and muscle fatigue than tasks with lower strain index values.Practitioner Summary: The strain index developed in this study is a conclusive estimation of the concavity compression required for shoulder joint stabilization. It can be used to identify the activities that may contribute to the risks of shoulder disorders. Abbreviation BLS Bureau of the Labor Statistics.

The assessment of material handling strategies in dealing with sudden loading: the effects of load handling position on trunk biomechanics.

Back injury caused by sudden loading is a significant risk among workers that perform manual handling tasks. The present study investigated the effects of load handling position on trunk biomechanics (flexion angle, L5/S1 joint moment and compression force) during sudden loading. Eleven subjects were exposed to a 6.8 kg sudden loading while standing upright, facing forward and holding load at three different vertical heights in the sagittal plane or 45° left to the sagittal plane (created by arm rotation). Results showed that the increase of load holding height significantly elevated the peak L5/S1 joint compression force and reduced the magnitude of trunk flexion. Further, experiencing sudden loading from an asymmetric direction resulted in significantly smaller peak L5/S1 joint compression force, trunk flexion angle and L5/S1 joint moment than a symmetric posture. These findings suggest that handling loads in a lower position could work as a protective strategy during sudden loading.

Discrete wavelet transform analysis of surface electromyography for the fatigue assessment of neck and shoulder muscles.

Assessment of neuromuscular fatigue is essential for early detection and prevention of risks associated with work-related musculoskeletal disorders. In recent years, discrete wavelet transform (DWT) of surface electromyography (SEMG) has been used to evaluate muscle fatigue, especially during dynamic contractions when the SEMG signal is non-stationary. However, its application to the assessment of work-related neck and shoulder muscle fatigue is not well established. Therefore, the purpose of this study was to establish DWT analysis as a suitable method to conduct quantitative assessment of neck and shoulder muscle fatigue under dynamic repetitive conditions. Ten human participants performed 40min of fatiguing repetitive arm and neck exertions while SEMG data from the upper trapezius and sternocleidomastoid muscles were recorded. The ten of the most commonly used wavelet functions were used to conduct the DWT analysis. Spectral changes estimated using power of wavelet coefficients in the 12-23Hz frequency band showed the highest sensitivity to fatigue induced by the dynamic repetitive exertions. Although most of the wavelet functions tested in this study reasonably demonstrated the expected power trend with fatigue development and recovery, the overall performance of the "Rbio3.1" wavelet in terms of power estimation and statistical significance was better than the remaining nine wavelets.

Biomechanical loading of the shoulder complex and lumbosacral joints during dynamic cart pushing task.

The primary objective of this study was to quantify the effect of dynamic cart pushing exertions on the biomechanical loading of shoulder and low back. Ten participants performed cart pushing tasks on flat (0°), 5°, and 10° ramped walkways at 20 kg, 30 kg, and 40 kg weight conditions. An optoelectronic motion capturing system configured with two force plates was used for the kinematic and ground reaction force data collection. The experimental data was modeled using AnyBody modeling system to compute three-dimensional peak reaction forces at the shoulder complex (sternoclavicular, acromioclavicular, and glenohumeral) and low back (lumbosacral) joints. The main effect of walkway gradient and cart weight, and gradient by weight interaction on the biomechanical loading of shoulder complex and low back joints was statistically significant (all p < 0.001). At the lumbosacral joint, negligible loading in the mediolateral direction was observed compared to the anterioposterior and compression directions. Among the shoulder complex joints, the peak reaction forces at the acromioclavicular and glenohumeral joints were comparable and much higher than the sternoclavicular joint. Increased shear loading of the lumbosacral joint, distraction loading of glenohumeral joint and inferosuperior loading of the acromioclavicular joint may contribute to the risk of work-related low back and shoulder musculoskeletal disorder with prolonged and repetitive use of carts.