3D Multiple Triangular Prisms for Highly Sensitive Non-Contact Mode Triboelectric Bending Sensors.

Here, a highly sensitive triboelectric bending sensor in non-contact mode operation, less sensitive to strain, is demonstrated by designing multiple triangular prisms at both sides of the polydimethylsiloxane film. The sensor can detect bending in a strained condition (up to 20%) as well as bending direction with quite high linear sensitivity (~0.12/degree) up to 120°, due to the electrostatic induction effect between Al and poly (glycerol sebacate) methacrylate. Further increase of the bending angle to 135° significantly increases the sensitivity to 0.16/degree, due to the contact electrification between them. The sensors are attached on the top and bottom side of the proximal interphalangeal and wrist, demonstrating a directional bending sensor with an enhanced sensitivity.

Phase-Tuned MoS2 and Its Hybridization with Perovskite Oxide as Bifunctional Catalyst: A Rationale for Highly Stable and Efficient Water Splitting.

The efficient realization of bifunctional catalysts has immense opportunities in energy conversion technologies such as water splitting. Transition metal dichalcogenides (TMDs) are considered excellent hydrogen evolution catalysts owing to their hierarchical atomic-scale layered structure and feasible phase transition. On the other hand, for efficient oxygen evolution, perovskite oxides offer the best performance based on their rational design and flexible compositional structure. A unique way to achieve an efficient hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in a single-cell configuration is through the hybridization of TMDs with perovskite oxides to form a bifunctional electrocatalyst. Here, we report a simple yet effective strategy to inherently tune the intrinsic properties of a TMD based on MoS2 and its hybridization with LaCoO3 perovskite oxide to deliver enhanced electrocatalytic activity for both the HER and OER. Detailed Raman and XPS measurements highlighted a clear phase transformation of MoS2 from a semiconducting to metallic phase by effectively tailoring the precursor compositions. Based on this, the morphological features yielded an interesting spherical flower-shaped nanostructure with vertically aligned petals of MoS2 with increased surface-active edge sites suitable for the HER. Subsequent hybridization of nanostructured MoS2 with LaCoO3 provides a bifunctional catalytic system with an increased BET surface area of 33.4 m2/g for an overall improvement in water splitting with a low onset potential (HER: 242 mV and OER: 1.6 V @10 mA cm-2) and Tafel slope (HER: 78 mV dec-1; OER: 62.5 mV dec-1). Additionally, the bifunctional catalyst system exhibits long-term stability of up to ∼400 h under continuous operation at a high current density of 50 mA cm-2. These findings will pave the way for developing cost-effective and less complex bifunctional catalysts by simply and inherently tuning the influential material properties for full-cell electrochemical water splitting.

Operation of Wearable Thermoelectric Generators Using Dual Sources of Heat and Light.

A wearable thermoelectric generator (WTEG) that utilizes human body heat can be a promising candidate for the wearable power generators. The temperature difference (ΔT) between the body and the environment is a stable source driving the WTEG, but this driving force is limited by the ambient temperature itself at the same time. Here, a novel WTEG that can be operated using the dual source of body heat and light with exceptionally high driving force is fabricated. The printable solar absorbing layer attached to the bottom of the WTEG absorbs ≈95% of the light from ultraviolet to far infrared and converts it into heat. To optimize the power density of WTEGs, the fill factor of the thermoelectric (TE) leg/electrode is considered through finite-difference time-domain (FDTD) simulation. When operated by the dual sources, the WTEG exhibits a power density of 15.33 µW cm-2 , which is the highest under "actual operating conditions" among all kinds of WTEGs. In addition, unlike conventional WTEGs, the WTEG retains 83.1% of its output power at an ambient temperature of 35 °C compared to its output power at room temperature. This study will accelerate the commercialization of WTEGs by introducing a novel method to overcome their limitations.

Stretchable and colorless freestanding microwire arrays for transparent solar cells with flexibility.

Transparent solar cells (TSCs) are emerging devices that combine the advantages of visible transparency and light-to-electricity conversion. Currently, existing TSCs are based predominantly on organics, dyes, and perovskites; however, the rigidity and color-tinted transparent nature of those devices strongly limit the utility of the resulting TSCs for real-world applications. Here, we demonstrate a flexible, color-neutral, and high-efficiency TSC based on a freestanding form of n-silicon microwires (SiMWs). Flat-tip SiMWs with controllable spacing are fabricated via deep-reactive ion etching and embedded in a freestanding transparent polymer matrix. The light transmittance can be tuned from ~10 to 55% by adjusting the spacing between the microwires. For TSCs, a heterojunction is formed with a p-type polymer in the top portion of the n-type flat-tip SiMWs. Ohmic contact with an indium-doped ZnO film occurs at the bottom, and the side surface has an Al2O3 passivation layer. Furthermore, slanted-tip SiMWs are developed by a novel solvent-assisted wet etching method to manipulate light absorption. Finite-difference time-domain simulation revealed that the reflected light from slanted-tip SiMWs helps light-matter interactions in adjacent microwires. The TSC based on the slanted-tip SiMWs demonstrates 8% efficiency at a visible transparency of 10% with flexibility. This efficiency is the highest among Si-based TSCs and comparable with that of state-of-the-art neutral-color TSCs based on organic-inorganic hybrid perovskite and organics. Moreover, unlike others, the stretchable and transparent platform in this study is promising for future TSCs.

Morphology-Controlled Aluminum-Doped Zinc Oxide Nanofibers for Highly Sensitive NO2 Sensors with Full Recovery at Room Temperature.

Room-temperature (RT) gas sensitivity of morphology-controlled free-standing hollow aluminum-doped zinc oxide (AZO) nanofibers for NO2 gas sensors is presented. The free-standing hollow nanofibers are fabricated using a polyvinylpyrrolidone fiber template electrospun on a copper electrode frame followed by radio-frequency sputtering of an AZO thin overlayer and heat treatment at 400 °C to burn off the polymer template. The thickness of the AZO layer is controlled by the deposition time. The gas sensor based on the hollow nanofibers demonstrates fully recoverable n-type RT sensing of low concentrations of NO2 (0.5 ppm). A gas sensor fabricated with Al2O3-filled AZO nanofibers exhibits no gas sensitivity below 75 °C. The gas sensitivity of a sensor is determined by the density of molecules above the minimum energy for adsorption, collision frequency of gas molecules with the surface, and available adsorption sites. Based on finite-difference time-domain simulations, the RT sensitivity of hollow nanofiber sensors is ascribed to the ten times higher collision frequency of NO2 molecules confined inside the fiber compared to the outer surface, as well as twice the surface area of hollow nanofibers compared to the filled ones. This approach might lead to the realization of RT sensitive gas sensors with 1D nanostructures.