Response Surface Methodology Optimization of Resistance Welding Process for Unidirectional Carbon Fiber/PPS Composites.

The use of thermoplastic composites (TPCs) as one of the lightweight solutions will inevitably encounter problems in connection. Resistance welding has the characteristics of high strength, simplicity, and high reliability, and is considered a very potential hot-melt connection technology. The resistance welding technology of unidirectional carbon fiber-reinforced polyphenylene sulfide composites (UCF/PPS) was systematically studied. The experimental results show that the 100-mesh brass mesh has the best resin wetting effect and heating efficiency, and the PPS/oxidized 100-mesh brass mesh composite resistance element (Ox-RE/PPS) has the highest welding strength. The welding failure mode changes from interface failure and RE failure to interlayer structure damage and fiber fracture. The single-factor experimental results show that the maximum welding strength is reached at 310 °C, 1.15 MPa, and 120 kW/m2. According to the conclusion of the single-factor experiment, the Box-Behnken method was further used to design a three-factor, three-level experiment, and a quadratic regression model was established according to the test results. The results of variance analysis, fitting curve analysis, and perturbation plot analysis proved that the model had high fitting and prediction abilities. From the 3D surface diagram analysis, the influence of power density is the largest, and the interaction between welding temperature and power density is the most significant. Combined with the analysis of Design Expert 13 software, the optimal range of process parameters was obtained as follows: welding temperature 313-314 °C, welding pressure 1.04-1.2 MPa, and power density 124-128 kW/m2. The average strength of resistance welding joints prepared in the optimal range of process parameters was 13.58 MPa.

Dissolution Behavior of Lime with Different Properties into Converter Slag.

China's 2022 crude steel production soared to an impressive 1.018 billion tons, and steel slag constituted approximately 10% to 15% of this massive output. However, a notable hindrance to the comprehensive utilization of steel slag arises from the fact that it contains 10% to 20% of free calcium oxide (f-CaO), resulting in volume instability. To address this challenge, our study delved into the dynamic transformation of the interface between lime and slag, as well as the fluctuations in the dissolution rate of lime. An Electron Probe Micro Analyzer, equipped with an energy-dispersive spectrometer, was employed for the analysis. Our findings revealed that the configuration of the reaction interface between quicklime and slag underwent alterations throughout various phases of converter smelting. At a temperature of 1400 °C, several significant transformations occurred, including the formation of a CaO-FeO solid solution, (Ca, Mg, Fe) olivine, and low-melting point (Ca, Mg) silicate minerals. With the gradual reduction in FeO content, a robust and high-melting 2CaO·SiO2 layer emerged, generated through the interaction between CaO and (Ca, Mg, Fe) olivine. Furthermore, for lime with a particle size of 20 mm and a calcination rate of 0%, the thickest layer of 2CaO·SiO2 was observed after 120 s of dissolution in slag A2 at 1400 °C. Overall, the dissolution rates of lime with different particle sizes in slag A1 to A4 showed a gradual increase. On the other hand, the dissolution rates of lime with different calcination rates in slag A1 to A4 exhibited an initial increase, followed by a decrease, and then another increase. The formation of a high-melting point and continuous dense 2CaO·SiO2 layer during the dissolution process hindered the mass transfer between lime and slag.

Improvement and Evaluation of a Device That Determines the Interfacial Shear Strength of Carbon Fiber/Polyphenylene Sulfide Composites.

This study improved homemade apparatus for characterizing the interfacial shear strength (IFSS) of carbon-fiber-reinforced polyphenylene sulfide (PPS/CF) composites. The upgraded generation II experimental device includes a newly developed experimental clamp for samples, as well as testing systems. Compared with the initial generation I apparatus and the commercial Toei instrument, the generation II device is easier and more efficient to operate. The average interfacial adhesion values obtained using these devices were consistently approximately 40 MPa, with relatively low data scatter, showing excellent repeatability and applicability during microbond tests. Notably, the generation II experimental device was equipped with an additional high-frequency data-capturing tool to identify the debonding peak force more precisely, which demonstrated a higher interfacial shear strength of 42.81 MPa during testing. Therefore, the new instrument was able to reflect the change in the interfacial stress state during the interface debonding process more accurately and reliably.

New Strategy for Improvement of Interfacial Interactions between Poly(arylene sulfide sulfone) and Carbon Fiber by Grafting Polymeric Chains via Thiol-Ene Click Chemistry.

A simple and efficient strategy for enhancing the interfacial interaction in carbon fiber-reinforced poly(arylene sulfide sulfone) (CF/PASS) composites by grafting polymeric chains via thiol-ene click chemistry is reported here. Simultaneously, three thiol compounds and carbon nanotubes were grafted on CFs to explore the reaction between the CF and thiol groups. X-ray photoelectron spectroscopy, Raman spectroscopy, and normalized temperature-dependent IR spectroscopy results confirm the successful grafting of three thiol compounds, carbon nanotubes, and polymer chains. Similarly, obvious changes on the CF surface can be seen before and after modification via scanning electron microscopy, such as grafted nanotubes and polymeric resin, and the increase in the modulus gradient and interfacial thickness of CF/PASS can be clearly seen via atomic force microscopy. All the results of micro and macro tests on mechanical properties indicate that connecting low molecular weight thiol-terminated PASS (HS-LPASS) onto CFs enhances the interfacial property and mechanical performance of CF/PASS to a greater extent. The interfacial shear strength, interlaminar shear strength, and tensile strength of CF@HS-LPASS-reinforced PASS (CF@HS-LPASS/PASS) increase significantly by 38.5, 43.6, and 24.4%, respectively. All the results demonstrate that thiol-ene click reactions can be used for CF modification; furthermore, in the presence of external stress, the grafted polymeric interphase can act as a "bridge layer" to improve the stress transfer efficiency.

Improve the Interfacial Properties between Poly(arylene sulfide sulfone) and Carbon Fiber by Double Polymeric Grafted Layers Designed on a Carbon Fiber Surface.

Double polymeric grafted layer is constructed by two steps of chemical reaction, in which two polymers had been used, respectively polydopamine (PDA) film and modified PASS (NH2-PASS) resin containing amine group, as the interphase in carbon fiber reinforced poly(arylene sulfide sulfone) (PASS) composite (CF/PASS) to work on enhancing the interfacial property. All the test results of chemical components and chemical structures on the carbon fiber surface show that the double polymeric grafted layer was constructed successfully with PDA and NH2-PASS chains. And obvious characteristics of thin PDA film and a polymer layer can be clearly seen in the morphology of modified carbon fiber. In addition to this, the obvious interphase and change in the thickness of interphase have been observed in the modulus distribution images of CF/PASS. The final superb performance is achieved by PASS composites with a double polymeric grafted layer, 27.2% and 198.6% superior to the original PASS composite for IFSS and ILSS, respectively. Moreover, the result also indicates that constructing a double polymeric grafted layer on a carbon fiber surface is a promising technique to modify carbon fiber for processing high-performance advanced thermoplastic composites and is more environmental friendly as well as convenient.

Segregated poly(arylene sulfide sulfone)/graphene nanoplatelet composites for electromagnetic interference shielding prepared by the partial dissolution method.

Segregated conductive polymer composites have been proved to be outstanding electromagnetic interference shielding (EMI) materials at low filler loadings. However, due to the poor interfacial adhesion between the pure conductive filler layers and segregated polymer granules, the mechanical properties of the segregated composites are usually poor, which limit their application. Herein, a simple and effective approach, the partial dissolution method, has been proposed to fabricate segregated poly(arylene sulfide sulfone) (PASS)/graphene nanoplatelet (GNP) composites with superior EMI shielding effectiveness (SE) and high tensile strength. Morphology examinations revealed that the GNPs were restricted in the dissolved outer layer by the undissolved cores, and there was a strong interaction between the PASS/GNP layer and the pure PASS core. The resultant PASS/GNP composites showed excellent electrical conductivity (60.3 S m-1) and high EMI SE (41 dB) with only 5 wt% GNPs. More notably, the tensile strength of the PASS/GNPs prepared by partial dissolution reached 36.4 MPa, presenting 136% improvement compared to that of the conventional segregated composites prepared by mechanical mixing. The composites also exhibited high resistance to elevated temperatures and chemicals owing to the use of the special engineering polymer PASS as a matrix.

[Application effect of pericardial devascularization plus gastric fundus transaction in advanced schistosomiasis].

OBJECTIVE: To discuss the effect of pericardial devascularization plus gastric fundus transaction in advance schistosomiasis patients with portal hypertension. METHODS: Thirty-six advanced schistosomiasis patients with portal hypertension treated with devascularization plus gastric fundus transaction (a portal hypertension group), as well as 10 patients treated with modified Sugiura operation (a modified Sugiura operation group) in the Third People's Hospital of Yangxin County since 2006 were chosen as the observation objects, and the clinical effects of the two groups were observed and compared. RESULTS: The operation time, indwelling time of stomach tube, time to taking food after operation, drainage tube removal time of the portal hypertension group were all shorten than those of the modified Sugiura operation group (all P＜0.05). The hospitalization expenses of the two groups were (25 466.00 ± 2 888.48) Yuan and (34 517.10 ± 4 948.39) Yuan respectively, and the difference was also statistically significant (P＜0.05). The incidence rates of portal thrombosis of the portal hypertension group and modified Sugiura operation group were 33.33% (12/36) and 40.00% (4/10), respectively, and the incidence rates of rehaemorrhagia of the two groups 12 months after the operation were 16.67% (6/36) and 10.00% (1/10), respectively, but the differences had no statistically significance (both P ＞ 0.05). In addition, 1 case with delayed gastric emptying and 1 case with stomal leak of esophagus happened in the modified Sugiura operation group, while no corresponding complications happened in the portal hypertension group. CONCLUSIONS: Pericardial devascularization plus gastric fundus is a relatively easy procedure which has a good short-term clinical effect, and therefore it is suitable for application in primary hospitals. However, its long-term effect still needs further observation.

Nonsynonymous single nucleotide polymorphisms in the complement component 3 gene are associated with risk of age-related macular degeneration: a meta-analysis.

Nonsynonymous single nucleotide polymorphisms (SNPs) in complement component 3 (CC3) are associated with the risk of age-related macular degeneration (AMD), however, this association is not consistent among studies. To thoroughly address this issue, we performed an updated meta-analysis to evaluate the association between nine SNPs in the CC3 gene and AMD risk. A search was conducted of the PubMed database through 3rd Aug, 2014. Odds ratios (ORs) and 95% confidence intervals (CIs) were used to assess the strength of associations. Based on the search criteria for manuscripts reporting AMD susceptibility related to CC3 in nine SNPs, 57 case-control studies from 22 different articles were retrieved. Significantly positive associations were found for the rs2230199 C/G SNP and AMD in the Caucasian population, as well as for the rs1047286 C/T SNP. Moreover, a relationship between the rs11569536 G/A SNP and AMD was detected. By contrast, a negative association was observed between rs2250656 A/G SNP and AMD risk. The present meta-analysis suggests that these four SNPs in the CC3 gene are potentially associated with the risk of AMD development. Further studies using larger sample sizes and accounting for gene-environment interactions should be conducted to elucidate the role of CC3 gene polymorphisms in AMD risk.

Association between a 27-bp variable number of tandem repeat polymorphism in intron 4 of the eNOS gene and risk for diabetic retinopathy Type 2 diabetes mellitus: a meta-analysis.

PURPOSE: Imbalance in the production of endothelial nitric oxide synthase (eNOS), which plays an essential role in retinal vascular function, can lead to the development of diabetic retinopathy (DR). To thoroughly address this issue, we performed an updated meta-analysis to evaluate the association between the eNOS 27VNTR (4b/4a) polymorphism and DR in type 2 diabetes mellitus (T2DM). METHODS: A search was conducted of PubMed and Chinese language (WanFang) databases through 3 March 2013. Data were retrieved in a systematic manner and analyzed using Stata Statistical Software. Crude odds ratios (ORs) with 95% confidence intervals (CIs) were used to assess the strength of associations. RESULTS: Based on the search criteria for DR susceptibility related to the 27VNTR (4b/4a) polymorphism of the eNOS gene, 16 case-control studies (15 articles), comprising 3227 T2DM patients with DR and 3437 T2DM patients without DR, were retrieved. Although no significant associations were uncovered in either the overall analysis or DR subtype groups, a decreased association was detected between the African- (allelic contrast: OR = 0.75, 95% CI = 0.65-0.88) or population-based (PB) studies (dominant genetic model: OR = 0.91, 95% CI = 0.83-0.98) and the eNOS 27VNTR (4b/4a) polymorphism. Stratification according to average duration of DM revealed that T2DM patients with histories of >10 years had an elevated susceptibility to DR compared with those with histories of shorter durations (homozygote comparison: OR = 1.67, 95% CI = 1.09-2.58). CONCLUSIONS: The present meta-analysis suggests that the eNOS 27VNTR (4b/4a) polymorphism potentially decreases the risk of developing DR in T2DM African individuals. The higher degree of susceptibility in patients with longer (>10 years) durations of DM is indicative of the involvement of a gene-environment interaction in determining the risk for DR. Further studies, based on larger sample sizes and additional gene-environment interactions, should be conducted to elucidate the role of eNOS gene polymorphisms, especially 27VNTR (4b/4a), in the risk for DR.