High-efficiency cleaning technology and lifespan prediction for the ceramic membrane treating secondary treated effluent.

Chemical cleaning is one of the key technical means to control membrane fouling, restore membrane flux and ensure the stable operation of membrane systems. In the experiment, the six most representative chemical cleaning agents for ceramic membranes, such as sulfuric acid (H2SO4), sodium hydroxide (NaOH), sodium hypochlorite (NaClO), ethylenediaminetetraacetic acid disodium salt (EDTA-Na2), sodium dodecyl sulfate (SDS) and nonylphenol polyoxyethylene ether (OP-10), were used as research objects. The cleaning effect of the two-step combined cleaning of chemical cleaning agents on the fouled membrane was systematically investigated. Results showed that the order of the chemical cleaning agent had a significant effect on the cleaning effect. The best chemical cleaning program was determined to be NaClO first and then SDS: the fouled ceramic membrane was soaked in NaClO solution at 0.15% for 2.5 h and further soaked in SDS solution at five times its own critical micelle concentration for 2.5 h. The predicted long-term lifespan of the ceramic membranes was 4.91 years. Scanning electron microscopy-energy spectrum analysis showed that the surface roughness of the cleaned ceramic membrane was slightly higher than that of the new membrane. The contact angle was slightly lower than that of the new membrane.

Fast and on-line link optimization for the long-distance two-way fiber-optic time and frequency transfer.

The performance of long-distance two-way fiber-optic time and frequency (T/F) transfer is directly affected by link parameters. In this paper, a fast on-line scheme to maximize the signal-to-noise ratio at the T/F transfer link ends (denoted by SNRW and SNRE) is proposed by optimizing the gains of bidirectional Erbium-doped fiber amplifiers (Bi-EDFAs). The dedicatedly defined objective optimization functions, ln(1/SNRW + 1/SNRE) for microwave and time transfer, and ln(1/SNRW) for optical frequency transfer, are proven to be a convex function and enable the computation time to be reduced significantly by employing the fast and mature convex optimization algorithm. The linear equations about the objective optimization function and the fiber parameters required by optimization are constructed, and then the fiber parameters are proposed to be on-line obtained accordingly by measuring the concerned SNR at the link end under different EDFA gain configurations and solving the linear equations. The transmission matrixes for the proposed optimization scheme are further derived, which can simplify the implementation in the long-distance multiple EDFAs links. The simulation shows that the proposed algorithm can obtain the optimal parameters consistent with the reported experimental results, and can reduce the computation time by more than four orders compared with the scanning optimization method for a link with more than 6 Bi-EDFAs.

Study on pickling technology to control fouling of ceramic membrane treating secondary treated effluent.

The application of membrane technology in the field of water treatment was increasingly widespread, but membrane fouling still restricted its development, and the membrane needed to be chemically cleaned. This research focused on the high-efficiency pickling technology of ceramic membrane, and developed the cleaning technology of ceramic membrane in cooperation with surfactant. In the experiment, the municipal secondary effluent was used as the raw water, and the single-step, mixed and step-by-step cleaning effects of three strong acids, three weak acids and surfactants on ceramic membranes and polyvinylidene difluoride (PVDF) membranes were investigated. For ceramic membrane, the optimal cleaning combination was H2SO4 first and then DTAC, and the flux recovery rate could reach 96.94%; for PVDF membrane, the optimal cleaning combination was HNO3 first and then H2SO4, and the flux recovery rate could reach 93.72%. In addition, the surface of initial, polluted, and cleaned membranes were analyzed by scanning electron microscope and contact angle, and the fouling mechanism of the ceramic membrane was analyzed. The results showed that through physical cleaning and chemical cleaning, most of the pollutants on the membrane surface and pores were removed. The cleaning method can effectively control the membrane pollution.

Study on interface thermodynamic mechanism of membrane fouling in flat sheet ceramic membrane treating oilfield produced water.

In this study, a flat sheet ceramic membrane experimental device was constructed, and the thermodynamics of membrane fouling interface was studied for oilfield produced water. The flux of ceramic membrane in three kinds of model solutions were measured with time, as well as the surface tension, contact Angle and Zeta potential of solid. The thermodynamic mechanism of membrane fouling interface combined with XDLVO theory were explored for three kinds of model solutions. The thermodynamic study of the interface of ceramic plate membrane shows that the total interaction energy between membrane and oil droplets decreases with the increase of the distance between two interfaces at initial stage of membrane fouling, and finally transforms from the mutual attraction to the mutual repulsion. The total interaction energy between reservoir and oil droplet is shown as mutual attraction, and the total interaction energy decreases with the increase of the distance between reservoir and oil droplet interface. The zeta potential of crude oil was affected by salinity to some extent. The electrostatic shielding effect of the salt ions leads to a decrease in the ζ-potential of the three solutions. They are in the order: model solution A > model solution B > model solution C. This leads to a decrease in the electrostatic interaction (EL). And since the oil layer has the same composition as the oil droplets, the EL interactions in the three solutions can behave as mutual repulsion.

Multi-GNSS Combined Orbit and Clock Solutions at iGMAS.

Global navigation services from the quad-constellation of GPS, GLONASS, BDS, and Galileo are now available. The international GNSS monitoring and assessment system (iGMAS) aims to evaluate the navigation performance of the current quad systems under a unified framework. In order to assess impact of orbit and clock errors on the positioning accuracy, the user range error (URE) is always taken as a metric by comparison with the precise products. Compared with the solutions from a single analysis center, the combined solutions derived from multiple analysis centers are characterized with robustness and reliability and preferred to be used as references to assess the performance of broadcast ephemerides. In this paper, the combination method of iGMAS orbit and clock products is described, and the performance of the combined solutions is evaluated by various means. There are different internal precisions of the combined orbit and clock for different constellations, which indicates that consistent weights should be assigned for individual constellations and analysis centers included in the combination. For BDS-3, Galileo, and GLONASS combined orbits of iGMAS, the root-mean-square error (RMSE) of 5 cm is achieved by satellite laser ranging (SLR) observations. Meanwhile, the SLR residuals are characterized with a linear pattern with respect to the position of the sun, which indicates that the solar radiation pressure (SRP) model adopted in precise orbit determination needs further improvement. The consistency between combined orbit and clock of quad-constellation is validated by precise point positioning (PPP), and the accuracies of simulated kinematic tests are 1.4, 1.2, and 2.9 cm for east, north, and up components, respectively.