Plastic particles in urban compost and their grain size distribution.

Gathering information on plastic particles in composts and the processes they undergo is important in terms of potentially limiting their further entry into the environment, for example, in improving the fertilising properties of soils. Microplastics (MPs) were determined in composts produced from urban greenery. They are present in decreasing order: polyethylene terephthalate, polystyrene, polyethylene, and polypropylene. The determination of polymers and additives used to improve their properties was performed by pyrolysis and gas chromatography with mass spectrometric detection (Py-GC/MS). Additives and microplastics are most concentrated in composts in the 0.315-0.63 and 0.63-1.25 mm grain size class, together with the carbon contained in the compost dry matter. Additives form 0.11-0.13% of MPs in dry matter of compost. The average concentration of microplastics in the particle size class from 0.63 to 1.25 mm is 2434 ± 224 mg/kg; in the total sample of composts, it is 1368 ± 286 mg/kg of P-MPs. For composts with particle size <2.5 mm, a relationship between the C/N ratio and the plastic particle concentration was statistically significant. It documents a similar behaviour of lignocellulose and plastic particles during the degradation processes. A relationship between the concentration of polymer markers and additives in the compost dry matter and their concentrations in the leachate has been demonstrated. The leachability from compost is higher for additives than for chemical compounds originating from the decomposition of the main components of MPs. The suitability of the use of the compost for agricultural purposes was monitored by the germination index (GI) for watercress. The lowest value of the GI was determined in the particle size class from 0.63 to 1.25 mm. The leachability of polymer markers and additives alone cannot explain the low GI value in this grain size class. The GI value is also influenced by the leachability of chemical compounds characterised by the value of dissolved organic carbon (DOC) and water-leachable nitrogen (Nw). A statistically significant dependence between DOC/Nw and the germination index value was found.

Environmental impact assessment of the coal yard and ambient pollution.

This study investigates the vertical distribution of pollutants emitted from coal yards using unmanned aerial vehicles (UAVs). Vertical concentration measurements of black carbon (BC) and particulate matter (PM) in a range of 1 m to 100 m above ground level (AGL) in the central coal yard showed clear spatial patterns and gradients of these pollutants. In addition, measurements were taken at specific heights (1 m, 30 m AGL, and 60 m AGL) at seven locations approximately 3 km from the yard. Thirteen measurements were carried out during the non-heating period under similar weather conditions. The measured BC concentrations decreased significantly with increasing altitude, with ground-level concentrations reaching 1.88 ± 0.61 µg/m3 and decreasing by over 46% at 80 m AGL. Similarly, PM10 concentrations at 60 m AGL decreased by 21.7%, with values of 25.99 ± 9.24 µg/m3 measured near the ground level and 16.52 ± 8.31 µg/m3 at 60 m AGL. The maximum coal particle pollution from the coal depot ranges from 500 to 1,000 m. The study showed a significant decrease in BC concentrations with height above the coal yard surface. Concentrations of PM10 and PM10-TSP showed a complex distribution influenced by local emissions and long-range particle transport. Meteorological factors, especially wind speed and direction, significantly influenced the pollutant dispersion. In addition, higher pollutant concentrations were measured during dry periods than after rainfall. The findings of this study contribute to a better understanding of the dispersion patterns and potential impacts of coal dust, enabling the implementation of targeted mitigation strategies and improved pollution control measures.

Effect of biochar addition on the improvement of the quality parameters of compost used for land reclamation.

The 5% addition of biochar in composting in rows contributes significantly to reducing volatile organic compound(VOC) emissions. When composting with the addition of biochar, the average temperature increased by 13 ± 6.7 °C during the whole period, and the thermophilic phase was extended by 11 days. The higher temperature supported a reduction in the time necessary for achieving the biological stability observed by the oxygen uptake rate by more than 10 days. For organic compounds formed by the degradation of easily degradable primary components (proteins), the addition of biochar significantly reduces the release of organic compounds with heterocyclically bound nitrogen (Norg-VOCs) and volatile sulfur compounds (VSCs). The end of the biodegradation process is indicated by a decrease in VOC concentrations below initial values in the input material. This state was achieved in the compost with added biochar after 47 days, while in compost without added biochar, it lasted 60 days.

The use of polymer compounds in the deposits from the combustion of briquettes in domestic heating as an identifier of fuel quality.

The utilisation of waste wood from furniture production brings new problems connected with an incomplete thermochemical decomposition of additives (chemicals for improving properties of plastics) in small heating with the addition of sources. Unique organic compounds produced by the combustion of waste wood allow the identification of the type of fuel. The organic compounds contained in the char deposits were analysed by pyrolysis gas chromatography with mass spectrometry. The deposits from the combustion of briquettes from furniture production contain organic compounds originating by decomposition of phenolic resins, aminoplasts (urea-formaldehyde, resorcinol-formaldehyde and melamine), polyurethanes and wood glue. Additives contained in the deposits include plasticisers such as phthalates (DEHP, dibutyl phthalate and diisobutyl phthalate), flame retardants (2-propanol, 1-chlorophosphate (3:1) and p-terphenyl). Deposits from the combustion of briquettes from virgin wood do not contain these compounds. The total amount of compounds identified in the deposits from the boiler, which do not come from virgin wood combustion, varies in the range between 4.25 and 6.25 g/kg. Phthalates (55.5%) and PVAc adhesives (18.6%) are the main anthropogenic compounds in the deposits from domestic boilers.

A review on properties, challenges and commercial aspects of eco-friendly biolubricants productions.

Lubricants operate as antifriction media, preserving machine reliability, facilitating smooth operation, and reducing the likelihood of frequent breakdowns. The petroleum-based reserves are decreasing globally, leading to price increases and raising concerns about environmental degradation. The researchers are concentrating their efforts on developing and commercializing an environmentally friendly lubricant produced from renewable resources. Biolubricants derived from nonedible vegetable oils are environmentally favorable because of their non-toxicity, biodegradability, and close to net zero greenhouse gas emissions. The demand for bio lubricants in industry and other sectors is increasing due to their non-toxic, renewable, and environmentally friendly nature. Good lubrication, anti-corrosion, and high flammability are characteristic properties of vegetable oils due to their unique structure. This study presents several key properties of nonedible oils that are used to produce lubricants via the transesterification process. Bibliometric analysis is also performed, which provides us with a better understanding of previous studies related to the production of bio lubricants from the transesterification process. Only 371 published documents in the Scopus database were found to relate to the production of bio lubricants using the transesterification process. The published work was mostly dominated by research articles (286; 77.088%). Significant development can be seen in recent years, with the highest occurrence in 2021, reaching 68 publications accounting for 18.38% of the total documents. In the second step, (i) the authors with the most number of publications; (ii) journals with the most productions; (iii) most productive countries; and (iv) the authors' most frequently used keywords were evaluated. These results will provide a pathway for researchers interested in this field. Lastly, recommendation is made on research gaps to device possible strategies for its commercialization.

Recent progress in microalgae-derived biochar for the treatment of textile industry wastewater.

Textile industry utilize a massive amount of dyes for coloring. The dye-containing effluent is released into wastewater along with heavy metals that are part of dye structure. The treatment of textile industry wastewater using conventional techniques (coagulation, membrane technique, electrolysis ion exchange, etc.) is uneconomical and less efficient (for a low concentration of pollutants). Moreover, most of these techniques produce toxic sludge, making them less environmentally friendly. Algae base industry is growing for food, cosmetics and energy needs. Algae biomass in unique compared to lignocellulosic biomass due to presence of various functional group on its surface and presence of various cations. These two characteristics are unique for biochar as a tool for environmental decontamination. Algae biomass contain functional groups and cations that can be effective for removal of organic contaminants (dyes) and heavy metals. Algae can be micro and macro and both have entirely different biomass composition which will lead to a synthesis of different biochar even under same synthesis process. This study reviews the recent progress in the development of an economically viable and eco-friendly approach for textile industry wastewater using algae biomass-derived absorbents. The strategy employed microalgal biochar to remove organic pollutants (dyes) and heavy metals from textile effluents by biosorption. This article discusses different methods for preparing algal biochar (pyrolysis, hydrothermal carbonization and torrefaction), and the adsorption capacity of biochar for dyes and heavy metals. Work on hydrothermal carbonization and torrefaction of microalgal biomass for biochar is limited. Variation in structural and functional groups changes on biochar compared to original microalgal biomass are profound in contract with lignocellulosic biomass. Existing Challenges, future goals, and the development of these technologies at the pilot level are also discussed.

Principles and potential of thermal hydrolysis of sewage sludge to enhance anaerobic digestion.

Sewage sludge is rich source of carbon, nutrients, and trace elements and can be subjected to proper treatment before disposal to fulfill government legislation and protect receiving environments. Anaerobic digestion (AD) is a well-adopted technology for stabilizing sewage sludge and recovering energy-rich biogas and nutrient-rich digestate. However, a slow hydrolysis rate limits the biodegradability of sludge. In the present study we have attempted to explain the potential of thermal hydrolysis to enhance anaerobic digestion of sewage sludge. Thermal pretreatment improves biodegradability and recycling of the sludge as an excellent energy and nutrients recovery source at reasonable capital (CAPEX) and operational (OPEX) costs. Other pretreatments like conventional (below/above 100 °C), temperature-phased anaerobic digestion (TPAD), microwave and chemically mediated thermal pretreatment have also been accounted. This review provides a holistic overview of sludge's characterization and value-added properties, various techniques used for sludge pretreatment for resource recovery, emphasizing conventional and advanced thermal pretreatment, challenges in scale-up of these technologies, and successful commercialization of thermal pretreatment techniques.

Emerging potential of spent coffee ground valorization for fuel pellet production in a biorefinery.

Abstract: The global market for fuel pellets (FPs) has been steadily growing because of a shift to coal substitutes. However, sustainability and the availability of biomass are the main issues. Various kinds of bio-wastes can be valorized through cutting-edge technologies. In the coffee industry, a valuable organic waste called spent coffee grounds (SCGs) is generated in bulk. SCG can be divided into two components, namely spent coffee ground oil and defatted spent coffee grounds (DSCG). SCG and DSCG can be used to produce FPs with excellent higher heating values. This review highlights that burning FPs composed of 100% SCG is not feasible due to the high emission of NOx. Moreover, the combustion is accompanied by a rapid temperature drop due to incomplete combustion which leads to lower boiler combustion efficiencies and increased carbon monoxide emissions. This was because of the low pellet strength and bulk density of the FP. Mixing SCG with other biomass offers improved boiler efficiency and emissions. Some of the reported optimized FPs include 75% SCG + 20% coffee silverskin, 30% SCG + 70% pine sawdust, 90% SCG + 10% crude glycerol, 32% SCG + 23% coal fines + 11% sawdust + 18% mielie husks + 10% waste paper + 6% paper pulp, and 50% SCG + 50% pine sawdust. This review noted the absence of combustion and emissions analyses of DSCG and the need for their future assessment. Valorization of DSCG offers a good pathway to improve the economics of an SCG-based biorefinery where the extracted SCGO can be valorized in other applications. The combustion and emissions of DSCG were not previously reported in detail. Therefore, future investigation of DSCG in boilers is essential to assess the potential of this industry and improve its economics. Supplementary Information: The online version contains supplementary material available at 10.1007/s10668-022-02361-z.

A state-of-the-art review on spent coffee ground (SCG) pyrolysis for future biorefinery.

Coffee is a globally consumed beverage that produces a substantial amount of valuable organic waste known as spent coffee grounds (SCG). Although SCG is a non-edible biomass, research initiatives focused on valorizing/utilizing its organic content, protecting the environment, and reducing the high oxygen demand required for its natural degradation. The integration with biorefinery in general and with pyrolysis process in specific is considerered the most successful solid waste management strategy of SCG that produce energy and high-value products. This paper aims at providing a quantitative analysis and discussion of research work done over the last 20 years on SCG as a feedstock in the circular bioeconomy (CBE). Management stratigies of SCG have been thoroughly reviewed and pyrolysis process has been explored as a novel technology in CBE. Results revealed that explored articles belong to Chemical, physical., biological and environmental science branches, with Energy & Fuels as the most reporting themes. Published works correlate SCG to renewable energy, biofuel, and bio-oil, with pyrolysis as a potential valorization approach. Literature review showed that only one study focused on the pyrolysis of defatted spent coffee grounds (DSCG). The insightful conclusions of this paper could assist in proposing several paths to more economically valorization of SCG through biorefinery, where extracted oil can be converted to biofuels or value-added goods. It was highlighted the importance of focusing on the coupling of SCG with CBE as solid waste managment strategy.

The quality of composts prepared in automatic composters from fruit waste generated by the production of beverages.

Ensuring the processing of food waste from the production of food and beverages intheautomatic composters can be difficult because of the physicochemical properties of input raw materials. Very often, the final product does not meet the requirements forcomposts according to the European Compost Network. Optimisation of input food waste from theproduction ofbeverages was performed by the addition of the bulk materials such assawdust and clay minerals (bentonite). Toxicity of the compost is caused by organic compounds with polar and non-polar properties. These compounds belong to the groups ofalcohols, aldehydes and ketones, carboxylic acids, tannin, and phenols, coumarins and terpenes. Phytotoxicity is mostly influenced by the group of terpenes. The addition ofsawdust used as bulking agent decreases the concentrations of almost all chemical compounds. Thegroup of tannin and compounds containing phenols represents an exception because these compounds are released from sawdust.

A performance evaluation study of nano-biochar as a potential slow-release nano-fertilizer from wheat straw residue for sustainable agriculture.

Agro-Wastes are identified as to manufacture potential valuable organic biochar fertilizer product economically while also managing the waste. Biochar (BC) produced from agriculture waste is helps to improve the soil because of its neutral pH, addition of organic carbon to the soil and lower salt index values. This study focused on the development of nano-biochar into a more enhanced biochar product where it was checked whether the biochar derived from wheat straw can absorb nutrients and then act as support matter for releasing micro-nutrients and macro-nutrients for the plants on slow liberation basis. Wheat biochar (WBC) and wheat nano-biochar (WBNC) were synthesized by pyrolysis at two different temperatures and nutrients were fused into the WBC via impregnation technique. Physical parameters such as Proximate, Ultimate analysis & other were also studied and inspected by standard control procedures. Studies were also carried out on water retention (WR), water absorbance (WA), swelling ratio (SR) and equilibrium water content (EWC) for all samples; data was collected and compared for the better sample. Slow-release studies performed portrayed the release pattern of nutrients for prolonged periods, which are very important for the plant growth, yield and productivity. Overall, the experimental results displayed that BNC produced at 350 °C showed promising features of (SI:0.05, SR: 3.67, WA:64%, EWC:78.6%, FC:53.05% and pH:7.22), is a good substance however the nano-biochar has improved results; environmental friendly & could be utilized as a potential fertilizer on slow release for sustainable and green agriculture application.

Environmental risks related to organic compounds from the combustion of paper briquettes in domestic boilers.

Environmental risks connected with the combustion of paper/cardboard briquettes are still not sufficiently known. This paper aims to bring attention to the risks related to the utilisation of paper briquettes in local boilers and to characterise these risks by means of the identification of organic compounds in deposits from exhaust flues. The identification of the chemical compounds was performed by pyrolysis gas chromatography with mass spectrometric detection. Paper/cardboard briquettes contain 119 compounds of biogenic origin derived from major biomass components and 53 additives. Additives are used both for improving the properties of paper and in printing inks. By burning the paper briquettes, the same 53 compounds from the additive group were caught in the deposits from the flue gas pathway, occurring in the range of 1-10% of the concentration of individual compounds (additives) contained in the input fuel. Compounds that are very stable during the combustion process have an enrichment factor (EF) >30, which corresponded to approximately 3% of the additive capture in deposits. The highest values were found for plasticisers (phthalates). Many of the primary organic compounds contained in the input raw material do not decompose during combustion and can have adverse effects on human health.

The potential environmental risks of the utilization of composts from household food waste.

Modern technologies (especially with the help of autonomous measurement and control systems) introduced automatic composters for the disposal of household food waste production. Environmental risks connected with the utilization of these composts can be characterized by the high electrical conductivity caused by a presence of sodium chloride in food. Electrical conductivity influences the ecotoxicity of the composts. The presence of pesticides in composted food also represents an important environmental problem. The following pesticides were found in compost samples from household food waste: 1,3,5-triazine, methyl trithion, bifenthrin, bifenox, carbophenothion, pirimicarb, dioxacarb, desmetryn. Pesticide content in composts varied from 0.3 to 16.3 µg/kg, the average value being 30.4 ± 10.1 µg/kg dry matter. The higher decomposition was found of "modern" pesticides in the composters. The removal of salts can ensure that inhibition will be < 30% while washing with the ratio of 1:3 will result in the inhibition < 5%. However, this way of processing is not effective for other organisms-Poecilia reticulata (mortality 100%) and Daphnia magna (immobilisation 100%) using this procedure as well as washing of the compost in the ratio 3:1.

Spent coffee ground as renewable energy source: Evaluation of the drying processes.

Spent coffee ground (SCG) is an environmental nuisance material, but, if appropriately processed it can be converted into pellets, and thus, used as an energy source. The moisture content of the final product should be below 10%, to ensure safe storage, and elimination of microorganism growth (particularly moulds). The present study aims to identify the optimal drying process for removing moisture from SCG and to investigate changes to the composition of SCG due to drying, at temperatures around 75 °C, so that the dried SCG to qualify as renewable energy source. Three drying processes were employed for SCG drying (with initial moisture content of about 65%): oven drying, solar drying and open air sun drying, while SCG samples were placed in aluminium trays with thicknesses of 1.25, 2.5 and 4 cm. Based on the experimental results for SCG samples with thickness 2.5 cm, the open air sun drying process required 10 h to reach final moisture content of 37%, while solar drying achieved 10% moisture content in 10 h and oven drying achieved 7% moisture content in 6 h. The solar drying process proved as the most advantageous, due to low energy requirements and adequate quality of dried SCG. Also, experiments indicated that SCG storage at "normal room conditions" resulted to equilibrium moisture content in SCG of 8%, regardless of the initial moisture content. Furthermore, instrumental analyses of the SCG, revealed changes to its composition for a number of chemical groups, such as aldehydes, ketones, phytosterols, alkaloids, lactones, alcohols, phenols, pyrans and furans, among others. It was also identified that the SCG colour was affected due to the drying process.

Concentration Variability of Water-Soluble Ions during the Acceptable and Exceeded Pollution in an Industrial Region.

This study investigates the chemical composition of water-soluble inorganic ions at eight localities situated in the Moravian-Silesian Region (the Czech Republic) at the border with Poland. Water-soluble inorganic ions were monitored in the winter period of 2018 (January, 11 days and February, 5 days). The set was divided into two periods: the acceptable period (the 24-h concentration of PM10 < 50 µg/m3) and the period with exceeded pollution (PM10 ˃ 50 µg/m3). Air quality in the Moravian-Silesian Region and Upper Silesia is among the most polluted in Europe, especially in the winter season when the concentration of PM10 is repeatedly exceeded. The information on the occurrence and behaviour of water-soluble inorganic ions in the air during the smog episodes in Europe is insufficient. The concentrations of water-soluble ions (chlorides, sulphates, nitrates, ammonium ions, potassium) during the exceeded period are higher by two to three times compared with the acceptable period. The major anions for both acceptable period and exceeded pollution are nitrates. During the period of exceeded pollution, percentages of water-soluble ions in PM10 decrease while percentages of carbonaceous matter and insoluble particles (fly ash) increase.

Properties of composts from household food waste produced in automatic composters.

The minimization of landfill deposition of waste containing biological components represents a big problem, especially in built-up residential areas. The main problem of biologically degradable municipal waste is the quantity and composition of household waste which can have an important influence on decomposition processes already in collecting vessels. An amount of household waste produced in residential areas in the Czech Republic varies from 31 to 337 g/person/day, with an average value of 250 g. Waste of plant material character is produced in the range from 22 to 291 g/person/day. Composts were prepared in the home composters from household food waste. After the end of the composting process, compost does not have the organic component sufficiently stabilized, which is documented by a high value of electrical conductivity of aqueous leachate reaching more than 4 mS/cm and low humification index. The value of the humification index pronouncedly increased after eight weeks from 0.05 to 0.85, while compost from composting of green waste using windrow system have humification index of 3.48. An aim of this work is the determination of properties of composts prepared from HFW in automatic composters and identification of differences compared with composts prepared from a mixture of biodegradable green waste.

Comparison of organic compounds in char and soot from the combustion of biomass in boilers of various emission classes.

The combustion of biomass in boilers of emission classes 2 and 3 produces deposits in the form of char and soot inside the combustion chamber. Char and soot differ in content of elemental carbon (EC) and organic carbon (OC) as well as in the content of organic compounds. Deposits from boilers of emission class 2 contain higher amounts of OC and EC than those from boilers of emission class 3. The only exception is deposits formed by the combustion of briquettes from hardwood in boilers of emission class 3 that contained approximately by up to 60 percent higher amount of OC and by approx. 100% more EC than deposits from combustion in boilers of emission class 2. Deposits identified as char are characterized by dominant organic compounds derived from thermic degradation of cellulose, lignin, phytosterols, terpenes, their alteration products, and aromatic hydrocarbons. Deposits identified as soot have dominant PAHs, compounds containing oxygen (furans, benzofurans, phenols) and compounds containing aliphatic nitrogen (benzonitrile). Char from boilers of emission class 2 contains approx. by 80% more alkanes and cycloalkanes, by 80% more nitriles, by 50% more carboxyl acids, by 230% more anhydrosaccharides, phytosterols and by 180% more PAHs. These differences can be utilized for identification of burned fuel.

Possibilities of the utilization of char from the pyrolysis of tetrapak.

Since the cellulose used in the production of tetrapak is of very high quality, the char generated during pyrolysis should be influenced mainly by the pyrolysis temperature. This article aims to determine the chemical composition of biochar prepared at the temperatures of 400, 500, 600 and 700 °C and its environmental properties determined by the presence of organic compounds with toxicity and relatively high mobility in the environment. The analytical pyrolysis of char was used to identify the following groups of organic compounds: alkanes, cycloalkanes, alkenes, cycloalkenes, alkynes, alkadiens, ethers, alcohols, nitrogen compounds, nitrils, ketones and aldehydes, compounds containing phenols, furans, benzofurans, PAHs (polycyclic aromatic hydrocarbons), carboxylic acids, compounds containing benzenes and markers indicative of the presence of synthetic polymers (polyethylene layers, a part of dyes, antioxidants, stabilizers), and fragments of cellulose. Concerning the use of char as a soil conditioner, its ecotoxicity was monitored (Folsomia candida) by monitoring its addition to the artificial soil (char addition: 0.5, 1, 2.5, 5, 10, 15, 20, 50 and 100%). The lowest reproduction inhibition of Folsomia candida is caused by biochar prepared at the temperature of 400 °C and 700 °C, but it is not suitable for the agricultural application, the concentration of PAHs is three times higher than the EBC limit. Low-density polyethylene which is present in the aseptic box in concentration of 6%, can degrade biochar so that it cannot be used as a soil amendment. The results of the char analyses show that the pyrolysis temperature is a decisive factor in the applicability of biochar.

Temporal and seasonal variations of black carbon in a highly polluted European city: Apportionment of potential sources and the effect of meteorological conditions.

Black carbon - a primary component of particulate matter emitted from an incomplete combustion of fossil fuels, biomass, and biofuels - has been found to have a detrimental effect on human health and the environment. Since black carbon emissions data are not readily available, no measures are implemented to reduce black carbon emissions. The temporal and seasonal variations of black carbon concentrations were evaluated during 2012-2014. The data were collected in the highly polluted European city - Ostrava, Czech Republic, surrounded by major highways and large industries. Significantly higher black carbon concentrations were obtained in Ostrava, relative to other European cities and the magnitude was equivalent to the magnitude of black carbon concentrations measured in Poland and China. The data were categorized to heating and non-heating seasons based on the periodic pattern of daily and monthly average concentrations of black carbon. A higher black carbon concentration was obtained during heating season than non-heating season and was primarily associated with an increase in residential coal burning and meteorological parameters. The concentration of black carbon was found to be negatively correlated with temperature and wind speed, and positively correlated with the relative humidity. Other black carbon sources potentially included emissions from vehicle exhaust and the local steel-producing industry.

Enrichment and distribution of 24 elements within the sub-sieve particle size distribution ranges of fly ash from wastes incinerator plants.

The management of an increasing amount of municipal waste via incineration has been gaining traction. Fly ash as a by-product of incineration of municipal solid waste is considered a hazardous waste due to the elevated content of various elements. The enrichment and distribution of 24 elements in fly ash from three wastes incinerators were evaluated. Two coarse (>100 µm and <100 µm) and five sub-sieve (12-16, 16-23, 23-34, 34-49, and 49-100 µm) particle size fractions separated on a cyclosizer system were analyzed. An enhancement in the enrichment factor was observed in all samples for the majority of elements in >100 µm range compared with <100 µm range. The enrichment factor of individual elements varied considerably within the samples as well as the sub-sieve particle size ranges. These variations were attributed primarily to: (i) the vaporization and condensation mechanisms, (ii) the different design of incineration plants, (iii) incineration properties, (iv) the type of material being incinerated, and (v) the affinity of elements.