Content of Patient Electronic Messages to Physicians in a Large Integrated System.

This quality improvement study describes the content of electronic health record messages from patients to physicians in a large integrated health care system using natural language processing algorithms.

Seismic anisotropy of the D″ layer induced by (001) deformation of post-perovskite.

Crystallographic preferred orientation (CPO) of post-perovskite (Mg,Fe)SiO3 (pPv) has been believed to be one potential source of the seismic anisotropic layer at the bottom of the lower mantle (D″ layer). However, the natural CPO of pPv remains ambiguous in the D″ layer. Here we have carried out the deformation experiments of pPv-(Mg0.75,Fe0.25)SiO3 using synchrotron radial X-ray diffraction in a membrane-driven laser-heated diamond anvil cell from 135 GPa and 2,500 K to 154 GPa and 3,000 K. Our results show that the intrinsic texture of pPv-(Mg0.75,Fe0.25)SiO3 should be (001) at realistic P-T conditions of the D″ layer, which can produce a shear wave splitting anisotropy of ∼3.7% with VSH>VSV. Considering the combined effect of both pPv and ferropericlase, we suggest that 50% or less of deformation is sufficient to explain the origin of the shear wave anisotropy observed seismically in the D″ layer beneath the circum-Pacific rim.

Combined resistive and laser heating technique for in situ radial X-ray diffraction in the diamond anvil cell at high pressure and temperature.

To extend the range of high-temperature, high-pressure studies within the diamond anvil cell, a Liermann-type diamond anvil cell with radial diffraction geometry (rDAC) was redesigned and developed for synchrotron X-ray diffraction experiments at beamline 12.2.2 of the Advanced Light Source. The rDAC, equipped with graphite heating arrays, allows simultaneous resistive and laser heating while the material is subjected to high pressure. The goals are both to extend the temperature range of external (resistive) heating and to produce environments with lower temperature gradients in a simultaneously resistive- and laser-heated rDAC. Three different geomaterials were used as pilot samples to calibrate and optimize conditions for combined resistive and laser heating. For example, in Run#1, FeO was loaded in a boron-mica gasket and compressed to 11 GPa then gradually resistively heated to 1007 K (1073 K at the diamond side). The laser heating was further applied to FeO to raise temperature to 2273 K. In Run#2, Fe-Ni alloy was compressed to 18 GPa and resistively heated to 1785 K (1973 K at the diamond side). The combined resistive and laser heating was successfully performed again on (Mg0.9Fe0.1)O in Run#3. In this instance, the sample was loaded in a boron-kapton gasket, compressed to 29 GPa, resistive-heated up to 1007 K (1073 K at the diamond side), and further simultaneously laser-heated to achieve a temperature in excess of 2273 K at the sample position. Diffraction patterns obtained from the experiments were deconvoluted using the Rietveld method and quantified for lattice preferred orientation of each material under extreme conditions and during phase transformation.

Slip systems in MgSiO3 post-perovskite: implications for D'' anisotropy.

Understanding deformation of mineral phases in the lowermost mantle is important for interpreting seismic anisotropy in Earth's interior. Recently, there has been considerable controversy regarding deformation-induced slip in MgSiO(3) post-perovskite. Here, we observe that (001) lattice planes are oriented at high angles to the compression direction immediately after transformation and before deformation. Upon compression from 148 gigapascals (GPa) to 185 GPa, this preferred orientation more than doubles in strength, implying slip on (001) lattice planes. This contrasts with a previous experiment that recorded preferred orientation likely generated during the phase transformation rather than deformation. If we use our results to model deformation and anisotropy development in the D'' region of the lower mantle, shear-wave splitting (characterized by fast horizontally polarized shear waves) is consistent with seismic observations.