High-Performance Flexible Bismuth Telluride Thin Film from Solution Processed Colloidal Nanoplates.

Thermoelectric generators are an environmentally friendly and reliable solid-state energy conversion technology. Flexible and low-cost thermoelectric generators are especially suited to power flexible electronics and sensors using body heat or other ambient heat sources. Bismuth telluride based thermoelectric materials exhibit their best performance near room temperature making them an ideal candidate to power wearable electronics and sensors using body heat. In this report Bi2Te3 thin films are deposited on a flexible polyimide substrate using low-cost and scalable manufacturing methods. The synthesized Bi2Te3 nanocrystals have a thickness of 35 ± 15 nm and a lateral dimension of 692 ± 186 nm. Thin films fabricated from these nanocrystals exhibit a peak power factor of 0.35 mW/m·K2 at 433 K, which is among the highest reported values for flexible thermoelectric films. In order to evaluate the flexibility of the thin films, static and dynamic bending tests were performed while monitoring the change in electrical resistivity. After 1000 bending cycles over a 50mm ROC, the change in electrical resistance of the film was 23%. Using our Bi2Te3 solutions, we demonstrated the ability to print thermoelectric thin films with an aerosol jet printer, highlighting the potential of additive manufacturing techniques for fabricating flexible thermoelectric generators.

Defect Engineering of ZnO Nanoparticles for Bioimaging Applications.

Many promising attributes of ZnO nanoparticles (nZnO) have led to their utilization in numerous electronic devices and biomedical technologies. nZnO fabrication methods can create a variety of intrinsic defects that modulate the properties of nZnO, which can be exploited for various purposes. Here we developed a new synthesis procedure that controls certain defects in pure nZnO that are theorized to contribute to the n-type conductivity of the material. Interestingly, this procedure created defects that reduced the nanoparticle band gap to ∼3.1 eV and generated strong emissions in the violet to blue region while minimizing the defects responsible for the more commonly observed broad green emissions. Several characterization techniques including thermogravimetric analysis, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, transmission electron microscopy, Raman, photoluminescence, and inductively coupled plasma mass spectrometry were employed to verify the sample purity, assess how modifications in the synthesis procedure affect the various defects states, and understand how these alterations impact the physical properties. Since the band gap significantly decreased and a relatively narrow visible emissions band was created by these defects, we investigated utilizing these new nZnO for bioimaging applications using traditional fluorescent microscopy techniques. Although most nZnO generally require UV excitation sources to produce emissions, we demonstrate that reducing the band gap allows for a 405 nm laser to sufficiently excite the nanoparticles to detect their emissions during live-cell imaging experiments using a confocal microscope. This work lays the foundation for the use of these new nZnO in various bioimaging applications and enables researchers to investigate the interactions of pure nZnO with cells through fluorescence-based imaging techniques.

A new class of doped nanobulk high-figure-of-merit thermoelectrics by scalable bottom-up assembly.

Obtaining thermoelectric materials with high figure of merit ZT is an exacting challenge because it requires the independent control of electrical conductivity, thermal conductivity and Seebeck coefficient, which are often unfavourably coupled. Recent works have devised strategies based on nanostructuring and alloying to address this challenge in thin films, and to obtain bulk p-type alloys with ZT>1. Here, we demonstrate a new class of both p- and n-type bulk nanomaterials with room-temperature ZT as high as 1.1 using a combination of sub-atomic-per-cent doping and nanostructuring. Our nanomaterials were fabricated by bottom-up assembly of sulphur-doped pnictogen chalcogenide nanoplates sculpted by a scalable microwave-stimulated wet-chemical method. Bulk nanomaterials from single-component assemblies or nanoplate mixtures of different materials exhibit 25-250% higher ZT than their non-nanostructured bulk counterparts and state-of-the-art alloys. Adapting our synthesis and assembly approach should enable nanobulk thermoelectrics with further increases in ZT for transforming thermoelectric refrigeration and power harvesting technologies.

Microstructural characterization of next generation nuclear graphites.

This article reports the microstructural characteristics of various petroleum and pitch based nuclear graphites (IG-110, NBG-18, and PCEA) that are of interest to the next generation nuclear plant program. Bright-field transmission electron microscopy imaging was used to identify and understand the different features constituting the microstructure of nuclear graphite such as the filler particles, microcracks, binder phase, rosette-shaped quinoline insoluble (QI) particles, chaotic structures, and turbostratic graphite phase. The dimensions of microcracks were found to vary from a few nanometers to tens of microns. Furthermore, the microcracks were found to be filled with amorphous carbon of unknown origin. The pitch coke based graphite (NBG-18) was found to contain higher concentration of binder phase constituting QI particles as well as chaotic structures. The turbostratic graphite, present in all of the grades, was identified through their elliptical diffraction patterns. The difference in the microstructure has been analyzed in view of their processing conditions.

Seebeck tuning in chalcogenide nanoplate assemblies by nanoscale heterostructuring.

Chalcogenide nanostructures offer promise for obtaining nanomaterials with high electrical conductivity, low thermal conductivity, and high Seebeck coefficient. Here, we demonstrate a new approach of tuning the Seebeck coefficient of nanoplate assemblies of single-crystal pnictogen chalcogenides by heterostructuring the nanoplates with tellurium nanocrystals. We synthesized bismuth telluride and antimony telluride nanoplates decorated with tellurium nanorods and nanofins using a rapid, scalable, microwave-stimulated organic surfactant-directed technique. Heterostructuring permits two- to three-fold factorial tuning of the Seebeck coefficient, and yields a 40% higher value than the highest reported for bulk antimony telluride. Microscopy and spectroscopy analyses of the nanostructures suggest that Seebeck tunability arises from carrier-energy filtration effects at the Te-chalcogenide heterointerfaces. Our approach of heterostructuring nanoscale building blocks is attractive for realizing high figure-of-merit thermoelectric nanomaterials.