Characterization and performance evaluation of in-house ultrafiltration membrane coupled with photocatalysis for 17α-methyltestosterone hormone removal.

17α-methyltestosterone (MT) hormone is a synthetic androgenic steroid hormone utilized to induce Nile tilapia transitioning for enhanced production yield. This study specifically focuses on the removal of MT through the utilization of photocatalytic membrane reactor (PMR), which employs an in-house polyvinylidene fluoride (PVDF) ultrafiltration membrane modified with 1% nanomaterials (either TiO2 or α-Fe2O3). The molecular weight cut-off (MWCO) of the in-house membrane falls within the ultrafiltration range. Under UV95W radiation, the PMR with PVDF/TiO2 and PVDF/α-Fe2O3 membranes achieved 100% MT removal at 140 and 160 min, respectively. The MT removal by the commercial NF03 membrane was only at 50%. In contrast, without light irradiation, the MT removal by all the membranes remained unchanged after 180 min, exhibiting lower performance. The incorporation of TiO2 and α-Fe2O3 enhanced water flux and MT removal of the membrane. Notably, the catalytic activity was limited by the distribution and concentration of the catalyst at the membrane surface. The water contact angle did not correlate with the water flux for the composited membrane. The degradation of MT aligned well with Pseudo-first-order kinetic models. Thus, the in-house ultrafiltration PMR demonstrated superior removal efficiency and lower operational costs than the commercial nanofiltration membrane, attributable to its photocatalytic activities.

Development of Free-Standing Titanium Dioxide Hollow Nanofibers Photocatalyst with Enhanced Recyclability.

Titanium dioxide hollow nanofibers (THN) are excellent photocatalysts for the photodegradation of Bisphenol A (BPA) due to their extensive surface area and good optical properties. A template synthesis technique is typically employed to produce titanium dioxide hollow nanofibers. This process, however, involves a calcination procedure at high temperatures that yields powder-form photocatalysts that require post-recovery treatment before recycling. Meanwhile, the immobilization of photocatalysts on/into a membrane has been reported to reduce the active surface area. Novel free-standing TiO2 hollow nanofibers were developed to overcome those shortcomings. The free-standing photocatalyst containing 0.75 g of THN (FS-THN-75) exhibited good adherence and connectivity between the nanofibers. The recyclability of FS-THN-75 outperformed the THN calcined at 600 °C (THN-600), which retained 80% of its original weight while maintaining excellent degradation performance. This study recommends the potential application of free-standing TiO2 hollow nanofibers as high potential novel photocatalysts for the treatment of BPA in wastewater.

Polyvinylidene Difluoride (PVDF) Hollow Fiber Membrane Incorporated with Antibacterial and Anti-Fouling by Zinc Oxide for Water and Wastewater Treatment.

The addition of antibacterial material to hollow fiber membranes improves the membrane anti-biofouling characteristics. Antibacterial membranes were fabricated in this study to improve membrane function while also extending membrane lifetime. Neat polyvinylidene difluoride (PVDF) and PVDF hollow fiber membrane with the incorporation of antibacterial agent zinc oxide (ZnO) nanoparticles with various loading (2.5-7.5 wt.%) were fabricated by using dry/wet spinning method. The membrane structure, particle distribution, functional group, hydrophilicity, and pore size of each membrane were all assessed. The result shows that all ZnO/PVDF hollow fiber membranes have the asymmetric structure with even dispersion of ZnO nanoparticles throughout the membranes. The results showed that increased ZnO loadings considerably improved membrane hydrophilicity, and average pore size, in addition to good performance of pure water flux. Antibacterial testing shows that ZnO incorporated in the membrane matrix and membrane surfaces prevents bacteria that cause biofouling from adhering to the membrane. ZnO/PVDF membrane recorded excellent bovine serum albumin (BSA) rejection at 93.4% ± 0.4 with flux recovery rate at 70.9% ± 2.1. These results suggest that antibacterial ZnO/PVDF hollow fiber membranes are promising in relation to reducing biofouling for various water and wastewater treatment.

Bisphenol A Removal Using Visible Light Driven Cu2O/PVDF Photocatalytic Dual Layer Hollow Fiber Membrane.

Bisphenol A (BPA) is amongst the endocrine disrupting compounds (EDCs) that cause illness to humans and in this work was removed using copper (I) oxide (Cu2O) visible light photocatalyst which has a narrow bandgap of 2.2 eV. This was done by embedding Cu2O into polyvinylidene fluoride (PVDF) membranes to generate a Cu2O/PVDF dual layer hollow fiber (DLHF) membrane using a co-extrusion technique. The initial ratio of 0.25 Cu2O/PVDF was used to study variation of the outer dope extrusion flowrate for 3 mL/min, 6 mL/min and 9 mL/min. Subsequently, the best flowrate was used to vary Cu2O/PVDF for 0.25, 0.50 and 0.75 with fixed outer dope extrusion flowrate. Under visible light irradiation, 10 mg/L of BPA was used to assess the membranes performance. The results show that the outer and inner layers of the membrane have finger-like structures, whereas the intermediate section of the membrane has a sponge-like structure. With high porosity up to 63.13%, the membrane is hydrophilic and exhibited high flux up to 13,891 L/m2h. The optimum photocatalytic membrane configuration is 0.50 Cu2O/PVDF DLHF membrane with 6 mL/min outer dope flowrate, which was able to remove 75% of 10 ppm BPA under visible light irradiation without copper leaching into the water sample.

Fouling Behavior in a High-Rate Anaerobic Submerged Membrane Bioreactor (AnMBR) for Palm Oil Mill Effluent (POME) Treatment.

The characteristics of foulant in the cake layer and bulk suspended solids of a 10 L submerged anaerobic membrane bioreactor (AnMBR) used for treatment of palm oil mill effluent (POME) were investigated in this study. Three different organic loading rates (OLRs) were applied with prolonged sludge retention time throughout a long operation time (270 days). The organic foulant was characterized by biomass concentration and concentration of extracellular polymeric substances (EPS). The thicknesses of the cake layer and foulant were analyzed by confocal laser scanning microscopy and Fourier transform infrared spectroscopy. The membrane morphology and inorganic elements were analyzed by field emission scanning electron microscope coupled with energy dispersive X-ray spectrometer. Roughness of membrane was analyzed by atomic force microscopy. The results showed that the formation and accumulation of protein EPS in the cake layer was the key contributor to most of the fouling. The transmembrane pressure evolution showed that attachment, adsorption, and entrapment of protein EPS occurred in the membrane pores. In addition, the hydrophilic charge of proteins and polysaccharides influenced the adsorption mechanism. The composition of the feed (including hydroxyl group and fatty acid compounds) and microbial metabolic products (protein) significantly affected membrane fouling in the high-rate operation.

Parallel factor analysis of fluorescence excitation emissions to identify seasonal and watershed differences in trihalomethane precursors.

Concentration and chemical composition of dissolved organic matter (DOM) play a major role in formation and speciation of disinfection by-products, such as trihalomethanes (THMs), in water treatment plants (WTPs) during disinfection. This study characterized DOM across the process trains of WTPs using fluorescence excitation emission matrices (EEMs) together with parallel factor analysis (PARAFAC). The PARAFAC model was developed from 216 EEMs of bimonthly water samples from three WTPs in Khon Kaen, Thailand, from May 2018 to Mar 2019. Three PARAFAC components identified were humic-like DOM of terrestrial, and microbial or agricultural origin, while the one protein-like component was previously defined as tryptophan-like fluorophore. The relationships between water quality parameters, including the maximum fluorescent intensities (Fmax) of PARAFAC components and THM formation potential (THM-FP) were investigated using Spearman's rank correlation. The Fmax of PARAFAC components, UVA254, DOC, and THM-FP were greater in dry season. Chloroform was the primary THM formed at two sites using surface water as their water source, while the site using surface water with saline groundwater intrusion had higher concentration of brominated THMs. Results indicated that Fmax of humic-like components extracted by PARAFAC analysis were the most accurate THM-FP surrogate parameter assessed for the water samples tested and the correlations between Fmax and THM-FP were site specific (ρ = 0.81-0.85). The result demonstrates that fluorescence spectroscopy analysis has yielded insights into relationships between the DOM optical characteristics and their total THM-FP even at sites with different speciation of THMs.