Studying Surface Chemistry of Mixed Conducting Perovskite Oxide Electrodes with Synchrotron-Based Soft X-rays.

A fundamental understanding of the electrochemical reactions and surface chemistry at the solid-gas interface in situ and operando is critical for electrode materials applied in electrochemical and catalytic applications. Here, the surface reactions and surface composition of a model of mixed ionic and electronic conducting (MIEC) perovskite oxide, (La0.8Sr0.2)0.95Cr0.5Fe0.5O3-δ (LSCrF8255), were investigated in situ using synchrotron-based near-ambient pressure (AP) X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine-structure spectroscopy (NEXAFS). The measurements were conducted with a surface temperature of 500 °C under 1 mbar of dry oxygen and water vapor, to reflect the implementation of the materials for oxygen reduction/evolution and H2O electrolysis in the applications such as solid oxide fuel cell (SOFC) and electrolyzers. Our direct experimental results demonstrate that, rather than the transition metal (TM) cations, the surface lattice oxygen is the significant redox active species under both dry oxygen and water vapor environments. It was proven that the electron holes formed in dry oxygen have a strong oxygen character. Meanwhile, a relatively higher concentration of surface oxygen vacancies was observed on the sample measured in water vapor. We further showed that in water vapor, the adsorption and dissociation of H2O onto the perovskite surface were through forming hydroxyl groups. In addition, the concentration of Sr surface species was found to increase over time in dry oxygen due to Sr surface segregation, with the presence of oxygen holes on the surface serving as an additional driving force. Comparatively, less Sr contents were observed on the sample in water vapor, which could be due to the volatility of Sr(OH)2. A secondary phase was also observed, which exhibited an enrichment in B-site cations, particularly in Fe and relatively in Cr, and a deficiency in A-site cation, notably in La and relatively in Sr. The findings and methodology of this study allow for the quantification of surface defect chemistry and surface composition evolution, providing crucial understanding and design guidelines in the electrocatalytic activity and durability of electrodes for efficient conversions of energy and fuels.

Surface Decorations on Mixed Ionic and Electronic Conductors: Effects on Surface Potential, Defects, and the Oxygen Exchange Kinetics.

The oxygen exchange kinetics of epitaxial Pr0.1Ce0.9O2-δ electrodes was modified by decoration with submonolayer amounts of different basic (SrO, CaO) and acidic (SnO2, TiO2) binary oxides. The oxygen exchange reaction (OER) rate and the total conductivity were measured by in situ PLD impedance spectroscopy (i-PLD), which allows to directly track changes of electrochemical properties after each deposited pulse of surface decoration. The surface chemistry of the electrodes was investigated by near-ambient pressure XPS measurements (NAP-XPS) at elevated temperatures and by low-energy ion scattering (LEIS). While a significant alteration of the OER rate was observed after decoration with binary oxides, the pO2 dependence of the surface exchange resistance and its activation energy were not affected, suggesting that surface decorations do not alter the fundamental OER mechanism. Furthermore, the total conductivity of the thin films does not change upon decoration, indicating that defect concentration changes are limited to the surface layer. This is confirmed by NAP-XPS measurements which find only minor changes of the Pr-oxidation state upon decoration. NAP-XPS was further employed to investigate changes of the surface potential step on decorated surfaces. From a mechanistic point of view, our results indicate a correlation between the surface potential and the altered oxygen exchange activity. Oxidic decorations induce a surface charge which depends on their acidity (acidic oxides lead to a negative surface charge), affecting surface defect concentrations, any existing surface potential step, potentially adsorption dynamics, and consequently also the OER kinetics.

Electronic and ionic effects of sulphur and other acidic adsorbates on the surface of an SOFC cathode material.

The effects of sulphur adsorbates and other typical solid oxide fuel cell (SOFC) poisons on the electronic and ionic properties of an SrO-terminated (La,Sr)CoO3 (LSC) surface and on its oxygen exchange kinetics have been investigated experimentally with near ambient pressure X-ray photoelectron spectroscopy (NAP-XPS), low energy ion scattering (LEIS) and impedance spectroscopy as well as computationally with density functional theory (DFT). The experiment shows that trace amounts of sulphur in measurement atmospheres form SO2- 4 adsorbates and strongly deactivate a pristine LSC surface. They induce a work function increase, indicating a changing surface potential and a surface dipole. DFT calculations reveal that the main participants in these charge transfer processes are not sub-surface transition metals, but surface oxygen atoms. The study further shows that sulphate adsorbates strongly affect oxygen vacancy formation energies in the LSC (sub-)surface, thus affecting defect concentrations and oxygen transport properties. To generalize these results, the investigation was extended to other acidic oxides which are technologically relevant as SOFC cathode poisons, such as CO2 and CrO3. The results unveil a clear correlation of work function changes and redistributed charge with the Smith acidity of the adsorbed oxide and clarify fundamental mechanistic details of atomic surface modifications. The impact of acidic adsorbates on various aspects of the oxygen exchange reaction rate is discussed in detail.

Correlating Surface Crystal Orientation and Gas Kinetics in Perovskite Oxide Electrodes.

Solid-gas interactions at electrode surfaces determine the efficiency of solid-oxide fuel cells and electrolyzers. Here, the correlation between surface-gas kinetics and the crystal orientation of perovskite electrodes is studied in the model system La0.8 Sr0.2 Co0.2 Fe0.8 O3 . The gas-exchange kinetics are characterized by synthesizing epitaxial half-cell geometries where three single-variant surfaces are produced [i.e., La0.8 Sr0.2 Co0.2 Fe0.8 O3 /La0.9 Sr0.1 Ga0.95 Mg0.05 O3-δ /SrRuO3 /SrTiO3 (001), (110), and (111)]. Electrochemical impedance spectroscopy and electrical conductivity relaxation measurements reveal a strong surface-orientation dependency of the gas-exchange kinetics, wherein (111)-oriented surfaces exhibit an activity >3-times higher as compared to (001)-oriented surfaces. Oxygen partial pressure ( p O 2 )-dependent electrochemical impedance spectroscopy studies reveal that while the three surfaces have different gas-exchange kinetics, the reaction mechanisms and rate-limiting steps are the same (i.e., charge-transfer to the diatomic oxygen species). First-principles calculations suggest that the formation energy of vacancies and adsorption at the various surfaces is different and influenced by the surface polarity. Finally, synchrotron-based, ambient-pressure X-ray spectroscopies reveal distinct electronic changes and surface chemistry among the different surface orientations. Taken together, thin-film epitaxy provides an efficient approach to control and understand the electrode reactivity ultimately demonstrating that the (111)-surface exhibits a high density of active surface sites which leads to higher activity.

Kinetics of competing exchange of oxygen and water at the surface of functional oxides.

The presence of water vapour in the input gas stream influences the performance of air electrodes of solid oxide cells. In this work, the oxygen transport kinetics were determined by isotopic exchange depth profiling at 350 °C on polycrystalline La0.6Sr0.4Co0.2Fe0.8O3-δ samples in humidified oxygen, comparing the differences in tracer diffusion profile using either 18O2 or H218O as the labelling medium. The apparent surface exchange coefficients of oxygen were determined in each case and used together to estimate the oxygen surface exchange coefficients of molecular oxygen and water. It was found that, in humid conditions, the surface exchange coefficient of molecular oxygen is significantly decreased in comparison to a reference in dry conditions. In addition, the surface exchange coefficient of water is higher than that for molecular oxygen. This is in good agreement with the hypothesis that, water monopolises the active exchange sites at the material surface and thus oxygen from water exchanges faster than the one of molecular oxygen.

Self-diffusion in garnet-type Li7La3Zr2O12 solid electrolytes.

Tetragonal garnet-type Li7La3Zr2O12 is an important candidate solid electrolyte for all-solid-state lithium ion batteries because of its high ionic conductivity and large electrochemical potential window. Here we employ atomistic simulation methods to show that the most favourable disorder process in Li7La3Zr2O12 involves loss of Li2O resulting in lithium and oxygen vacancies, which promote vacancy mediated self-diffusion. The activation energy for lithium migration (0.45 eV) is much lower than that for oxygen (1.65 eV). Furthermore, the oxygen migration activation energy reveals that the oxygen diffusion in this material can be facilitated at higher temperatures once oxygen vacancies form.

Surface Restructuring of Thin-Film Electrodes Based on Thermal History and Its Significance for the Catalytic Activity and Stability at the Gas/Solid and Solid/Solid Interfaces.

Electrodes in solid-state energy devices are subjected to a variety of thermal treatments, from film processing to device operation at high temperatures. All these treatments influence the chemical activity and stability of the films, as the thermally induced chemical restructuring shapes the microstructure and the morphology. Here, we investigate the correlation between the oxygen reduction reaction (ORR) activity and thermal history in complex transition metal oxides, in particular, La0.6Sr0.4CoO3-δ (LSC64) thin films deposited by pulsed laser deposition. To this end, three ∼200 nm thick LSC64 films with different processing and thermal histories were studied. A variety of surface-sensitive elemental characterization techniques (i.e., low-energy ion scattering, X-ray photoelectron spectroscopy, and secondary ion mass spectrometry) were employed to thoroughly investigate the cationic distribution from the outermost surface to the film/substrate interface. Moreover, electrochemical impedance spectroscopy was used to study the activity and the stability of the films. Our investigations revealed that, despite the initial comparable ORR activity at 600 °C, the degradation rates of the films differed by twofold in the long-term stability tests at 500 °C. Here, we emphasize the importance of processing and thermal history in the elemental surface distribution, especially for the stability of LSC64 electrodes and propose that they should be considered as among the main pillars in the design of active surfaces.

A CO2 -Tolerant Perovskite Oxide with High Oxide Ion and Electronic Conductivity.

Mixed ionic-electronic conductors (MIECs) that display high oxide ion conductivity (σo ) and electronic conductivity (σe ) constitute an important family of electrocatalysts for a variety of applications including fuel cells and oxygen separation membranes. Often MIECs exhibit sufficient σe but inadequate σo . It has been a long-standing challenge to develop MIECs with both high σo and stability under device operation conditions. For example, the well-known perovskite oxide Ba0.5 Sr0.5 Co0.8 Fe0.2 O3- δ (BSCF) exhibits exceptional σo and electrocatalytic activity. The reactivity of BSCF with CO2 , however, limits its use in practical applications. Here, the perovskite oxide Bi0.15 Sr0.85 Co0.8 Fe0.2 O3- δ (BiSCF) is shown to exhibit not only exceptional bulk transport properties, with a σo among the highest for known MIECs, but also high CO2 tolerance. When used as an oxygen separation membrane, BiSCF displays high oxygen permeability comparable to that of BSCF and much higher stability under CO2 . The combination of high oxide transport properties and CO2 tolerance in a single-phase MIEC gives BiSCF a significant advantage over existing MIECs for practical applications.

Designing Optimal Perovskite Structure for High Ionic Conduction.

Solid-oxide fuel/electrolyzer cells are limited by a dearth of electrolyte materials with low ohmic loss and an incomplete understanding of the structure-property relationships that would enable the rational design of better materials. Here, using epitaxial thin-film growth, synchrotron radiation, impedance spectroscopy, and density-functional theory, the impact of structural parameters (i.e., unit-cell volume and octahedral rotations) on ionic conductivity is delineated in La0.9 Sr0.1 Ga0.95 Mg0.05 O3- δ . As compared to the zero-strain state, compressive strain reduces the unit-cell volume while maintaining large octahedral rotations, resulting in a strong reduction of ionic conductivity, while tensile strain increases the unit-cell volume while quenching octahedral rotations, resulting in a negligible effect on the ionic conductivity. Calculations reveal that larger unit-cell volumes and octahedral rotations decrease migration barriers and create low-energy migration pathways, respectively. The desired combination of large unit-cell volume and octahedral rotations is normally contraindicated, but through the creation of superlattice structures both expanded unit-cell volume and large octahedral rotations are experimentally realized, which result in an enhancement of the ionic conductivity. All told, the potential to tune ionic conductivity with structure alone by a factor of ≈2.5 at around 600 °C is observed, which sheds new light on the rational design of ion-conducting perovskite electrolytes.

Oxygen transport and surface exchange mechanisms in LSCrF-ScCeSZ dual-phase ceramics.

For the mechanisms by which the oxygen gets incorporated in a dual-phase composite system, three hypotheses, i.e. cation inter-diffusion, spillover type and self-cleaning of the perovskite-structured phase, have been provided in the literature. However, experimentally a consensus on the most likely mechanism is yet to be reached. In this work, a specially fused sample of the lanthanum strontium chromium ferrite (LSCrF)-scandia/ceria-stabilised zirconia (ScCeSZ) dual-phase material was investigated. Among the three potential mechanisms, no obvious cation inter-diffusion was firstly observed. A cleaner surface of the ScCeSZ phase was confirmed in the fused sample than in the isolated ScCeSZ single-phase sample while impurity layers were clearly observed on the LSCrF surface, suggesting the cleaning effect from the perovskite. However, more evidence implies that the cleaning effect is not the only reason for the synergistic effects between these two phases. Observations via SIMS analysis lend strong support to the 'spillover-type' mechanism as the oxygen isotopic fraction on the surface of the ScCeSZ increased compared to the isolated single-phase and as the distance to the heterojunction increases, the oxygen isotopic fraction decreases. Moreover, oxygen depleted layers were clearly seen on the top layers of the LSCrF surface which may be associated with the higher oxygen diffusivity in the surface/sub-surface layers, oxygen grain boundary fast diffusion and the impurities on the perovskite phase. For this sample, a combination of 'spillover' and 'self-cleaning' type mechanisms is suggested to be the potential possibility while the contribution from the cation inter-diffusion for this specific sample is proven to be low.

Unveiling the Outstanding Oxygen Mass Transport Properties of Mn-Rich Perovskites in Grain Boundary-Dominated La0.8Sr0.2(Mn1-x Co x )0.85O3±Î´ Nanostructures.

Ion transport in solid-state devices is of great interest for current and future energy and information technologies. A superior enhancement of several orders of magnitude of the oxygen diffusivity has been recently reported for grain boundaries in lanthanum-strontium manganites. However, the significance and extent of this unique phenomenon are not yet established. Here, we fabricate a thin film continuous composition map of the La0.8Sr0.2(Mn1-x Co x )0.85O3±Î´ family revealing a substantial enhancement of the grain boundary oxygen mass transport properties for the entire range of compositions. Through isotope-exchange depth profiling coupled with secondary ion mass spectroscopy, we show that this excellent performance is not directly linked to the bulk of the material but to the intrinsic nature of the grain boundary. In particular, the great increase of the oxygen diffusion in Mn-rich compositions unveils an unprecedented catalytic performance in the field of mixed ionic-electronic conductors. These results present grain boundaries engineering as a novel strategy for designing highly performing materials for solid-state ionics-based devices.

Electrical conductivity and oxygen diffusion behaviour of the (La0.8Sr0.2)0.95CrxFe1-xO3-δ (x = 0.3, 0.5 and 0.7) A-site deficient perovskites.

Lanthanum strontium chromite ferrite ((La0.8Sr0.2)0.95CrxFe1-xO3-δ, LSCrF) pellets with 5% A-site deficiency were fabricated and the electrical conductivity and oxygen diffusion behaviour with different Cr substitution levels (x = 0.3, 0.5 and 0.7) were investigated. As the Cr content increased, the electrical conductivity increased and then a maximum value was achieved at x = 0.7. In the oxygen diffusion studies, all the measured materials present good surface exchange rates (>9 × 10-8 cm s-1 at 900 °C) while the bulk diffusivity of the investigated materials decreased as the Cr substitution level increased: at 900 °C the oxygen diffusion coefficients of the LSCrF materials (x = 0.3, 0.5 and 0.7) are 1.1 × 10-10 cm2 s-1, 3.7 × 10-12 cm2 s-1 and 8.6 × 10-13 cm2 s-1, respectively. Oxygen diffusion in the perovskite materials (LSCrF) is shown to be bulk diffusion limited and it was found that analysis on this type of material using the line scan mode in Time-of-Flight Secondary Ion Mass Spectrometry may result in significant underestimation of the surface exchange coefficient due to the oxygen saturation, while the depth profile mode provides more reliable results but the obtained surface exchange coefficients may also only reach a lower limit. Moreover, fast grain boundary diffusion behaviour was observed in the LSCrF (x = 0.7) material and the Le Claire, and Chung and Wuensch approximations were applied to analyse the oxygen diffusion profiles. For this material, the two approximations provided similar results for the grain boundary product (Dgbδ) and under the assumption that the width of a grain boundary is on the nanometre scale, the oxygen diffusion coefficient of the grain boundaries was about 3-4 orders of magnitude higher than that of the bulk at temperatures ≤900 °C.

Interface Effects on the Ionic Conductivity of Doped Ceria-Yttria-Stabilized Zirconia Heterostructures.

Multilayered heterostructures of Ce0.85Sm0.15O2-δ and Y0.16Zr0.92O2-δ of a high crystallographic quality were fabricated on (001)-oriented MgO single crystal substrates. Keeping the total thickness of the heterostructures constant, the number of ceria-zirconia bilayers was increased while reducing the thickness of each layer. At each interface Ce was found primarily in the reduced, 3+ oxidation state in a layer extending about 2 nm from the interface. Concurrently, the conductivity decreased as the thickness of the layers was reduced, suggesting a progressive confinement of the charge transport along the YSZ layers. The comparative analysis of the in-plane electrical characterization suggests that the contribution to the total electrical conductivity of these interfacial regions is negligible. For the smallest layer thickness of 2 nm the doped ceria layers are electrically insulating and the ionic transport only occurs through the zirconia layers. This is explained in terms of a reduced mobility of the oxygen vacancies in the highly reduced ceria.

Electronic properties and surface reactivity of SrO-terminated SrTiO3 and SrO-terminated iron-doped SrTiO3.

Surface reactivity and near-surface electronic properties of SrO-terminated SrTiO3 and iron doped SrTiO3 were studied with first principle methods. We have investigated the density of states (DOS) of bulk SrTiO3 and compared it to DOS of iron-doped SrTiO3 with different oxidation states of iron corresponding to varying oxygen vacancy content within the bulk material. The obtained bulk DOS was compared to near-surface DOS, i.e. surface states, for both SrO-terminated surface of SrTiO3 and iron-doped SrTiO3. Electron density plots and electron density distribution through the entire slab models were investigated in order to understand the origin of surface electrons that can participate in oxygen reduction reaction. Furthermore, we have compared oxygen reduction reactions at elevated temperatures for SrO surfaces with and without oxygen vacancies. Our calculations demonstrate that the conduction band, which is formed mainly by the d-states of Ti, and Fe-induced states within the band gap of SrTiO3, are accessible only on TiO2 terminated SrTiO3 surface while the SrO-terminated surface introduces a tunneling barrier for the electrons populating the conductance band. First principle molecular dynamics demonstrated that at elevated temperatures the surface oxygen vacancies are essential for the oxygen reduction reaction.

Surface Chemistry of La0.99Sr0.01NbO4-d and Its Implication for Proton Conduction.

Acceptor-doped LaNbO4 is a promising electrolyte material for proton-conducting fuel cell (PCFC) applications. As charge transfer processes govern device performance, the outermost surface of acceptor-doped LaNbO4 will play an important role in determining the overall cell performance. However, the surface composition is poorly characterized, and the understanding of its impact on the proton exchange process is rudimentary. In this work, the surface chemistry of 1 atom % Sr-doped LaNbO4 (La0.99Sr0.01NbO4-d, denoted as LSNO) proton conductor is characterized using LEIS and SIMS. The implication of a surface layer on proton transport is studied using the isotopic exchange technique. It has shown that a Sr-enriched but La-deficient surface layer of about 6-7 nm thick forms after annealing the sample under static air at 1000 °C for 10 h. The onset of segregation is found to be between 600 and 800 °C, and an equilibrium surface layer forms after 10 h annealing. A phase separation mechanism, due to the low solubility of Sr in LaNbO4, has been proposed to explain the observed segregation behavior. The surface layer was concluded to impede the water incorporation process, leading to a reduced isotopic fraction after the D216O wet exchange process, highlighting the impact of surface chemistry on the proton exchange process.

The effects of lattice strain, dislocations, and microstructure on the transport properties of YSZ films.

Enhanced conductivity in YSZ films has been of substantial interest over the last decade. In this paper we examine the effects of substrate lattice mismatch and film thickness on the strain in YSZ films and the resultant effect on the conductivity. 8 mol% YSZ films have been grown on MgO, Al2O3, LAO and NGO substrates, thereby controlling the lattice mismatch at the film/substrate interface. The thickness of the films was varied to probe the interfacial contribution to the transport properties, as measured by impedance spectroscopy and tracer diffusion. No enhancement in the transport properties of any of the films was found over single crystal values, and instead the effects of lattice strain were found to be minimal. The interfaces of all films were more resistive due to a heterogeneous distribution of grain boundaries, and no evidence for enhanced transport down dislocations was found.

Back-exchange: a novel approach to quantifying oxygen diffusion and surface exchange in ambient atmospheres.

A novel two-step Isotopic Exchange (IE) technique has been developed to investigate the influence of oxygen containing components of ambient air (such as H2O and CO2) on the effective surface exchange coefficient (k*) of a common mixed ionic electronic conductor material. The two step 'back-exchange' technique was used to introduce a tracer diffusion profile, which was subsequently measured using Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The isotopic fraction of oxygen in a dense sample as a function of distance from the surface, before and after the second exchange step, could then be used to determine the surface exchange coefficient in each atmosphere. A new analytical solution was found to the diffusion equation in a semi-infinite domain with a variable surface exchange boundary, for the special case where D* and k* are constant for all exchange steps. This solution validated the results of a numerical, Crank-Nicolson type finite-difference simulation, which was used to extract the parameters from the experimental data. When modelling electrodes, D* and k* are important input parameters, which significantly impact performance. In this study La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF6428) was investigated and it was found that the rate of exchange was increased by around 250% in ambient air compared to high purity oxygen at the same pO2. The three experiments performed in this study were used to validate the back-exchange approach and show its utility.

Investigating the Dendritic Growth during Full Cell Cycling of Garnet Electrolyte in Direct Contact with Li Metal.

All-solid-state batteries including a garnet ceramic as electrolyte are potential candidates to replace the currently used Li-ion technology, as they offer safer operation and higher energy storage performances. However, the development of ceramic electrolyte batteries faces several challenges at the electrode/electrolyte interfaces, which need to withstand high current densities to enable competing C-rates. In this work, we investigate the limits of the anode/electrolyte interface in a full cell that includes a Li-metal anode, LiFePO4 cathode, and garnet ceramic electrolyte. The addition of a liquid interfacial layer between the cathode and the ceramic electrolyte is found to be a prerequisite to achieve low interfacial resistance and to enable full use of the active material contained in the porous electrode. Reproducible and constant discharge capacities are extracted from the cathode active material during the first 20 cycles, revealing high efficiency of the garnet as electrolyte and the interfaces, but prolonged cycling leads to abrupt cell failure. By using a combination of structural and chemical characterization techniques, such as SEM and solid-state NMR, as well as electrochemical and impedance spectroscopy, it is demonstrated that a sudden impedance drop occurs in the cell due to the formation of metallic Li and its propagation within the ceramic electrolyte. This degradation process is originated at the interface between the Li-metal anode and the ceramic electrolyte layer and leads to electromechanical failure and cell short-circuit. Improvement of the performances is observed when cycling the full cell at 55 °C, as the Li-metal softening favors the interfacial contact. Various degradation mechanisms are proposed to explain this behavior.

Double perovskite cathodes for proton-conducting ceramic fuel cells: are they triple mixed ionic electronic conductors?

18O and 2H diffusion has been investigated at a temperature of 300 °C in the double perovskite material PrBaCo2O5+δ (PBCO) in flowing air containing 200 mbar of 2H216O. Secondary ion mass spectrometry (SIMS) depth profiling of exchanged ceramics has shown PBCO still retains significant oxygen diffusivity (~1.3 × 10-11 cm2s-1) at this temperature and that the presence of water (2H216O), gives rise to an enhancement of the surface exchange rate over that in pure oxygen by a factor of ~3. The 2H distribution, as inferred from the 2H216O- SIMS signal, shows an apparent depth profile which could be interpreted as 2H diffusion. However, examination of the 3-D distribution of the signal shows it to be nonhomogeneous and probably related to the presence of hydrated layers in the interior walls of pores and is not due to proton diffusion. This suggests that PBCO acts mainly as an oxygen ion mixed conductor when used in PCFC devices, although the presence of a small amount of protonic conductivity cannot be discounted in these materials.

Oxygen exchange and transport in dual phase ceramic composite electrodes.

Composites consisting of a perovskite-based electronic or mixed conductor with a fluorite-structured ionic conductor are often used as electrodes in solid oxide electrochemical energy conversion devices. After sintering the materials, there is often evidence for inter-reaction between the two phases, or inter-diffusion of cations or impurities between the two phases. We studied the (18)O exchange properties of a composite consisting of CGO and LSCF in a 50 : 50 ratio. High resolution ToF-SIMS mapping reveals that the (18)O fraction at the very outer surface of grains of the CGO phase is much higher than expected from D* and k* values for the single-phase parent material. Surface compositional analysis by ToF-SIMS and low energy ion scattering (LEIS) spectroscopy suggests that the surfaces of the CGO grains in the composite do not show the impurities which typically segregate to the surface in single-phase CGO. Thus, the "cleaning" of impurities from the CGO surface by dissolution into the perovskite phase may be one explanation for the apparent enhanced surface exchange for CGO in these composites.