Shallow-level defect passivation by 6H perovskite polytype for highly efficient and stable perovskite solar cells.

The power conversion efficiency of perovskite solar cells continues to increase. However, defects in perovskite materials are detrimental to their carrier dynamics and structural stability, ultimately limiting the photovoltaic characteristics and stability of perovskite solar cells. Herein, we report that 6H polytype perovskite effectively engineers defects at the interface with cubic polytype FAPbI3, which facilitates radiative recombination and improves the stability of the polycrystalline film. We particularly show the detrimental effects of shallow-level defect that originates from the formation of the most dominant iodide vacancy (VI+) in FAPbI3. Furthermore, additional surface passivation on top of the hetero-polytypic perovskite film results in an ultra-long carrier lifetime exceeding 18 µs, affords power conversion efficiencies of 24.13% for perovskite solar cells, 21.92% (certified power conversion efficiency: 21.44%) for a module, and long-term stability. The hetero-polytypic perovskite configuration may be considered as close to the ideal polycrystalline structure in terms of charge carrier dynamics and stability.

Recent progress of eco-friendly manufacturing process of efficient perovskite solar cells.

Perovskite solar cells (PSCs) have the potential to produce solar energy at a low cost, with flexibility, and high power conversion efficiency (PCE). However, there are still challenges to be addressed before mass production of PSCs, such as prevention from degradation under external stresses and the uniform, large-area formation of all layers. Among them, the most challenging aspect of mass production of PSCs is creating a high-quality perovskite layer using environmentally sustainable processes that are compatible with industry standards. In this review, we briefly introduce the recent progresses upon eco-friendly perovskite solutions/antisolvents and film formation processes. The eco-friendly production methods are categorized into two: (1) employing environmentally friendly solvents for perovskite precursor ink/solution, and (2) replacing harmful, volatile antisolvents or even limiting their use during the perovskite film formation process. General considerations and criteria for each category are provided, and detailed examples are presented, specifically focused on the works have done since 2021. In addition, the importance of controlling the crystallization behavior of the perovskite layer is highlighted to develop antisolvent-free perovskite formation methods.

Rationally Designed Eco-Friendly Solvent System for High-Performance, Large-Area Perovskite Solar Cells and Modules.

The important but remained issue to be addressed to achieve the mass production of perovskite solar modules include a large-area fabrication of high-quality perovskite film with eco-friendly, viable production methods. Although several efforts are made to achieve large-area fabrication of perovskite, the development of eco-friendly solvent system, which is precisely designed to be fit to scale-up methods are still challenging. Herein, this work develops the eco-friendly solvent/co-solvent system to produce a high-quality perovskite layer with a bathing in eco-friendly antisolvent. The new co-solvent/additive, methylsulfonylmethane (MSM), efficiently improves the overall solubility and has a suitable binding strength to the perovskite precursor, resulting in a high-quality perovskite film with antisolvent bathing method in large area. The resultant perovskite solar cells showed high power conversion efficiency of over 24% (in reverse scan), with a good long-term stability under continuous light illumination or damp-heat condition. MSM is also beneficial to produce a perovskite layer at low-temperature or high-humidity. MSM-based solvent system is finally applied to large-area, resulting in highly efficiency perovskite solar modules with PCE of 19.9% (by aperture) or 21.2% (by active area) in reverse scan. These findings contribute to step forward to a mass production of perovskite solar modules with eco-friendly way.

Roll-to-roll gravure-printed flexible perovskite solar cells using eco-friendly antisolvent bathing with wide processing window.

Driven by recent improvements in efficiency and stability of perovskite solar cells (PSCs), upscaling of PSCs has come to be regarded as the next step. Specifically, a high-throughput, low-cost roll-to-roll (R2R) processes would be a breakthrough to realize the commercialization of PSCs, with uniform formation of precursor wet film and complete conversion to perovskite phase via R2R-compatible processes necessary to accomplish this goal. Herein, we demonstrate the pilot-scale, fully R2R manufacturing of all the layers except for electrodes in PSCs. Tert-butyl alcohol (tBuOH) is introduced as an eco-friendly antisolvent with a wide processing window. Highly crystalline, uniform formamidinium (FA)-based perovskite formation via tBuOH:EA bathing was confirmed by achieving high power conversion efficiencies (PCEs) of 23.5% for glass-based spin-coated PSCs, and 19.1% for gravure-printed flexible PSCs. As an extended work, R2R gravure-printing and tBuOH:EA bathing resulted in the highest PCE reported for R2R-processed PSCs, 16.7% for PSCs with R2R-processed SnO2/FA-perovskite, and 13.8% for fully R2R-produced PSCs.

Achieving Long-Term Operational Stability of Perovskite Solar Cells with a Stabilized Efficiency Exceeding 20% after 1000 h.

Perovskite solar cells (PSCs) with mesoporous TiO2 (mp-TiO2) as the electron transport material attain power conversion efficiencies (PCEs) above 22%; however, their poor long-term stability is a critical issue that must be resolved for commercialization. Herein, it is demonstrated that the long-term operational stability of mp-TiO2 based PSCs with PCE over 20% is achieved by isolating devices from oxygen and humidity. This achievement attributes to systematic understanding of the critical role of oxygen in the degradation of PSCs. PSCs exhibit fast degradation under controlled oxygen atmosphere and illumination, which is accompanied by iodine migration into the hole transport material (HTM). A diffusion barrier at the HTM/perovskite interface or encapsulation on top of the devices improves the stability against oxygen under light soaking. Notably, a mp-TiO2 based PSC with a solid encapsulation retains 20% efficiency after 1000 h of 1 sun (AM1.5G including UV) illumination in ambient air.

Synthesis of Single-Crystalline Hexagonal Graphene Quantum Dots from Solution Chemistry.

Graphene-based carbon nanostructures with nanometer dimensions have been of great interest due to the existence of a bandgap. So far, well-ordered edge structure and uniformly synthesized graphene quantum dots (GQDs) with a hexagonal single-crystalline structure have not been directly observed owing to the limited precision of current synthesis approaches. Herein, we report on a novel approach not just for the synthesis of the size-controlled single-crystalline GQDs with hexagonal shape but also for a new discovery on constructing 2D and 3D graphene single crystal structures from d-glucose via catalytic solution chemistry. With size-controlled single-crystalline GQDs, we elucidated the crucial role of edge states on luminescence from the correlation between their crystalline size and exciton lifetime. Furthermore, blue-emissive single-crystalline GQDs were used as an emitter on light-emitting diodes and exhibit stable deep-blue emission regardless of the voltage and doping level.

Gravure-Printed Flexible Perovskite Solar Cells: Toward Roll-to-Roll Manufacturing.

Recent advances in perovskite solar cells (PSCs) have resulted in greater than 23% efficiency with superior advantages such as flexibility and solution-processability, allowing PSCs to be fabricated by a high-throughput and low-cost roll-to-roll (R2R) process. The development of scalable deposition processes is crucial to realize R2R production of flexible PSCs. Gravure printing is a promising candidate with the benefit of direct printing of the desired layer with arbitrary shape and size by using the R2R process. Here, flexible PSCs are fabricated by gravure printing. Printing inks and processing parameters are optimized to obtain smooth and uniform films. SnO2 nanoparticles are uniformly printed by reducing surface tension. Perovskite layers are successfully formed by optimizing the printing parameters and subsequent antisolvent bathing. 2,2',7,7'-Tetrakis-(N,N-di-4-methoxyphenylamino)-9,9'-spirobifluorene is also successfully printed. The all-gravure-printed device exhibits 17.2% champion efficiency, with 15.5% maximum power point tracking efficiency for 1000 s. Gravure-printed flexible PSCs based on a two-step deposition of perovskite layer are also demonstrated. Furthermore, a R2R process based on the gravure printing is demonstrated. The champion efficiency of 9.7% is achieved for partly R2R-processed PSCs based on a two-step fabrication of the perovskite layer.

An Outbreak of Scombroid Fish Poisoning Associated with Consumption of Yellowtail Fish in Seoul, Korea.

BACKGROUND: In November 2016, an outbreak of scombroid fish poisoning occurred among elementary school students in Seoul, Korea. An epidemiological investigation was conducted to identify the cause and source of the illness. METHODS: A case-control study was conducted among school members who had eaten lunch in the school. The histamine level in the suspect food item (yellowtail steak) was measured. RESULTS: Fifty-five (5.4%) of 1,017 school members who consumed fish for lunch fell ill. The principal symptoms were flushing (100%) and headache (72.7%); the median incubation period was 40 minutes. All had consumed yellowtail steak (odds ratio, 9.24; 95% confidence interval, 1.22-69.91). Leftover steak had an elevated histamine level (293 mg/kg), higher than the allowed 200 mg/kg. CONCLUSION: An outbreak of scombroid fish poisoning was confirmed; this is the first such report in Korea. Detailed food safety guidelines must be established.

Facile Synthesis of Composition-Controlled Graphene-Supported PtPd Alloy Nanocatalysts and Their Applications in Methanol Electro-Oxidation and Lithium-Oxygen Batteries.

A new and simple approach is reported for the synthesis of uniformly dispersed PtPd alloy nanocatalysts supported on graphene nanoplatelets (GNPs) (PtPd-GNPs) through the introduction of bifunctional materials, which can modify the GNP surface and simultaneously reduce metal ions. With the use of poly(4-styrenesulfonic acid), poly(vinyl pyrrolidone), poly(diallyldimethylammonium chloride), and poly(vinyl alcohol) as bifunctional materials, PtPd-GNPs can be produced through a procedure that is far simpler than previously reported methods. The as-prepared nanocrystals on GNPs clearly exhibit uniform PtPd alloy structures of around 2 nm in size, which are strongly anchored and well distributed on the GNP sheets. The Pt/Pd atomic ratio and loading density of the nanocrystals on the GNPs are controlled easily by changing the metal precursor feed ratio and the mass ratio of GNP to the metal precursor, respectively. As a result of the synergism between Pt and Pd, the as-prepared PtPd-GNPs exhibit markedly enhanced electrocatalytic performance during methanol electro-oxidation compared with monometallic Pt-GNP or commercially available Pt/C. Furthermore, the PtPd-GNP nanocatalysts also show greatly enhanced catalytic activity toward the oxygen reduction/evolution reaction in a lithium-oxygen (Li-O2 ) process, resulting in greatly improved cycling stability of a Li-O2 battery.

HYP-1, a novel diamide compound, relieves inflammatory and neuropathic pain in rats.

In the present study, we investigated whether a novel compound, 2-(2-(4-((4-chlorophenyl)(phenyl)methyl) piperazin-1-yl)-2-oxoethylamino)-N-(3,4,5-trimethoxybenzyl)acetamide (HYP-1), is capable of binding to voltage-gated sodium channels (VGSCs) and evaluated both its inhibitory effect on Na+ currents of the rat dorsal root ganglia (DRG) sensory neuron and its in vivo analgesic activity using rat models of inflammatory and neuropathic pain. HYP-1 showed not only high affinity for rat sodium channel (site 2), but also potent inhibitory activity against the TTX-R Na+ currents of the rat DRG sensory neuron. HYP-1 co-injected with formalin (5%, 50 µl) under the plantar surface of rat hind paw dose-dependently reduced spontaneous pain behaviors during both the early and late phases. This result was confirmed by c-Fos immunofluorescence in the L4-5 spinal segments. A large number of c-Fos-positive neurons were observed in rat injected with a mixture of formalin and vehicle, but not in rat treated with a mixture of formalin and HYP-1. In addition, the effectiveness of HYP-1 (6 and 60 mg/kg, i.p.) in suppression of neuropathic pain, such as mechanical, cold and warm allodynia, induced by rat tail nerve injury was investigated. HYP-1 showed limited selectivity over hERG, N-type and T-type channels.Our present results indicate that HYP-1, as a VGSC blocker, has potential analgesic activities against nociceptive, inflammatory and neuropathic pain.

Optical characteristics of a refractive optical attenuator with respect to the wedge angles of a silicon optical leaker.

We design, fabricate, and characterize the micromachined refractive variable optical attenuator (VOA) with a wedge-shaped silicon optical leaker (SOL). The vertical structures of the VOA device can be simply fabricated by deep reactive ion etching with no sidewall metallization, and the 8 degrees angled fibers are employed for a high return loss even in air-ambient conditions. The SOL successively transmits and refracts part of the incident light far outside the acceptance angle of the output fiber, showing an effective optical attenuation. The fabricated VOA gives high optical performances, such as a response time of 6 ms, a return loss of 39 dB, an insertion loss of 0.6 dB, an attenuation range of 43 dB, and a polarization-dependent loss (PDL) of a 10% attenuation level, including a wavelength-dependent loss. The optical characteristics of the VOA are also theoretically investigated with respect to the wedge angles of the SOL. The experimental characteristics are in good agreement with the theoretical values calculated, considering light scattered from the endface of an optical fiber and sidewall of the SOL. The PDL estimation was confirmed especially to sufficiently explain the fundamental characteristic of the PDL for the refractive VOA.