Influence of material and surface treatment on composite repair shear bond strength.

OBJECTIVES: The aim of this study is to investigate the influence of the composite material and surface treatment to the bond strength when repairing an aged composite surface with new composite. MATERIALS AND METHODS: One hundred and sixty resin blocks of methacrylate composite and silorane composite prepared and aged in artificial saliva for 6 months. Specimens treated either with a diamond bur (DB) or air abrasion (AA), conditioned with orthophosphoric acid (OA) or sodium hypochloride (SH) and repaired with methacrylate or silorane composite using the corresponding adhesive system. Repaired composites underwent thermocycling fatigue (×5000), and bond strength was measured at shear. RESULTS: Methacrylate achieved the highest bond strengths as repair material, in all combinations (26.54-55.56 MPa). Silorane only reached 8.12 MPa when repairing silorane treated with DB and OA. For all other treatment combinations repairing with silorane led to pretest failures. The most susceptible to repair composites/surface treatment combination is when repairing methacrylate treated with AA and SH and methacrylate composite (55.56 MPa). CONCLUSIONS: Silorane composites are not suitable to be used when repairing an old composite restoration. The repair material is the most critical factor, while aged surface treatment has only a minor influence to the shear bond strength.

Spectrophotometric analysis of the effectiveness of a novel in-office laser-assisted tooth bleaching method using Er,Cr:YSGG laser.

The purpose of this in vitro study was to compare the effectiveness of a novel Er,Cr:YSGG laser-assisted in-office tooth bleaching method with a conventional method by spectrophotometric analysis of the tooth color change. Furthermore, the influence of the application time of the bleaching gel on the effectiveness of the methods and the maintenance of the results 7 days and 1 month after the treatments were also evaluated. Twenty-four bovine incisors were stained and randomly distributed into four groups. Group 1 specimens received an in-office bleaching treatment with 35% H2O2 for 2 × 15 min. Group 2 specimens received the same treatment but with extended application time (2 × 20 min). In Group 3, the same in-office bleaching procedure (2 × 15 min) was carried out as that in Group 1, using Er,Cr:YSGG laser irradiation for 2 × 15 s on each specimen to catalyze the reaction of H2O2 breakdown. Group 4 specimens received the same bleaching treatment as Group 3 but with extended application time (2 × 20 min). Er,Cr:YSGG laser-assisted tooth bleaching treatment is more effective than the conventional treatment regarding color change of the teeth. Application time of the bleaching agent may influence the effectiveness of the methods. The color change of the tested treatments decreases after 7 days and 1 month. The clinical relevance of this study is that this novel laser-assisted bleaching treatment may be more advantageous in color change and application time compared to the conventional bleaching treatment.

Effect of Fluoride Treatments on Bleached Enamel Microhardness and Surface Morphology.

PURPOSE: To evaluate the effect of three different fluoride treatments on the surface microhardness and morphology of human enamel exposed to two different bleaching agents. MATERIALS AND METHODS: Twenty-three extracted human third molars were sectioned to obtain 90 enamel fragments, mounted on acrylic resin supports, polished and randomly divided into 9 groups (n = 10). The specimens were exposed to a combination of two bleaching agents (22% carbamide peroxide [CP] and 38% hydrogen peroxide [HP]) and three fluoride treatments (0.05% NaF daily, 0.2% NaF weekly and 5% NaF final topical fluoridation). The positive control group specimens were not exposed to bleaching agents or fluoride treatments. The negative control group specimens were exposed to the bleaching agents but none of the fluoride treatments. All specimens were stored in artificial saliva during the entire experiment, and enamel microhardness was evaluated. Surface microhardness data were statistically analysed using two-way ANOVA and Tukey's post-hoc test at a significance level of α = 0.05. Additionally, three specimens of each experimental group were examined under SEM. RESULTS: Two-way ANOVA revealed significant differences between the experimental groups (p < 0.05). The bleached group specimens which did not receive fluoride treatment exhibited significantly lower microhardness than those treated with fluoride (p < 0.05). Varying degrees of surface changes were observed among the experimental groups. CONCLUSION: Both bleaching agents significantly reduced enamel microhardness and the topical fluoride treatments after bleaching significantly enhanced the surface microhardness of the enamel. The surface morphology of the enamel was altered after bleaching and fluoride treatments.

Effect of preheating and shade on surface microhardness of silorane-based composites.

AIM: The aim of the present study was to evaluate the effect of preheating and shade on the surface microhardness of silorane-based composites. METHODS: Three shades of two different types of composites were evaluated: a silorane-based composite and a methacrylate-based composite. The composites were tested at 23°C, and after preheating at 55°C. Five specimens were prepared for each experimental group. The top surface of the specimens was irradiated for 20 s using an LED unit. Vickers microhardness test was used to evaluate both top and bottom surfaces of the specimens, followed by 24-h storage in the dark. Statistical analysis was performed using one-way anova and Tukey's post-hoc test at a level of significance of α = 0.05. RESULTS: There was a significant rise in microhardness as the temperature increased from 23 to 55°C for both the top and bottom surfaces of the tested composites (P < 0.05). The C2 shade of both composites exhibited the lowest microhardness (P < 0.05), while the A2 and A3 shades did not show significant differences compared to each other (P > 0.05) Filtek Silorane presented significantly lower microhardness than Filtek Z250 (P < 0.05), regardless of the temperature, shade, or depth of measurement. CONCLUSIONS: Preheating, shade, and composition of the tested composite resins affected their surface microhardness.

Effect of Er,Cr:YSGG laser irradiation on bovine enamel surface during in-office tooth bleaching ex vivo.

The aim of this in vitro study was to evaluate the effect of using Er,Cr:YSGG laser during in-office tooth bleaching on bovine enamel surface to evaluate the safety of this therapy on tooth tissues. Thirty-six enamel specimens were prepared from bovine incisors and divided into three groups: Group 1 specimens (control) received no bleaching treatment; Group 2 received a conventional in-office bleaching treatment (40 % H2O2); Group 3 received laser-assisted bleaching procedure (40 % H2O2) utilizing an Er,Cr:YSGG laser. The specimens were stored for 10 days after the bleaching treatment in artificial saliva. Vickers hardness was determined using a microhardness tester, and measurements for surface roughness were done using a VSI microscope. Three specimens for each experimental group were examined under SEM and mineral composition of the specimens was evaluated using EDS. Data were statistically analyzed using one-way ANOVA, Tukey's post hoc, Wilcoxon signed rank and Kruskal-Wallis tests (a = 0.05). The Vickers hardness of the enamel was reduced after in-office bleaching procedures (p < 0.05), and changes in surface morphology of the enamel were observed. However, the surface roughness of the enamel was not influenced (p > 0.05), and no changes in mineral composition of the enamel were detected after in-office bleaching procedures (p > 0.05). The laser-assisted bleaching treatment with Er,Cr:YSGG laser did not influence the enamel surface compared to the conventional bleaching technique. The safety of the use of Er,Cr:YSGG laser during in-office tooth bleaching regarding the surface properties of the enamel was confirmed under in vitro conditions.

In Vitro Inhibition of Enamel Demineralisation by Fluoride-releasing Restorative Materials and Dental Adhesives.

PURPOSE: To determine the ability of 5 contemporary fluoride-releasing restoratives and 3 fluoride-releasing adhesives to inhibit enamel demineralisation surrounding restorations, and the associations between inhibition and the levels of fluoride released from these materials. MATERIALS AND METHODS: Five fluoride-releasing restoratives (Fuji IX GP, Ketac N100, Dyract Extra, Beautifil II and Wave) and 3 fluoride-releasing adhesives (Stae, Prime & Bond NT and Fluoro Bond II) were investigated. Eight disks of each material were prepared. Fluoride release was measured daily using a fluoride-ion-selective electrode for 15 days. Twenty-four cavities for each group were restored with a restorative and an adhesive. Specimens were subjected to thermal stress and stored for 30 days in saline solution. After a 15-day pH-cycling regimen, two 150-µm-thick sections were derived from each specimen. Enamel lesion depth was measured at 0, 100, and 200 µm from each restoration's margin via polarised light microscopy. RESULTS: Of the restoratives investigated, Fuji IX GP released the most fluoride. The fluoride-releasing restoratives tested exhibited shallower enamel lesions than did the control group at all distances tested (p < 0.05). Fuji IX GP yielded significantly lower enamel lesion depth than did the other experimental materials. The depths of enamel lesions did not differ significantly when comparing restoratives applied with a fluoride-releasing adhesive with those applied with a non-fluoride-releasing adhesive. CONCLUSION: The fluoride-releasing materials tested reduced enamel demineralisation but to different extents, depending on their levels of fluoride release. Fluoride-releasing adhesives did not influence enamel lesion formation.

Dentinogenic Activity of Biodentine in Deep Cavities of Miniature Swine Teeth.

INTRODUCTION: The aim of the present study was to evaluate comparatively the bioactivity potential of a calcium silicate-based material (Biodentine; Septodont, Saint-Maur-des-fosses Cedex, France) after the restoration of deep dentinal cavities of miniature swine teeth with or without the application of a calcium hydroxide-containing pulp protective base (Dycal; Caulk Lab, Milford, DE). METHODS: Thirty-three permanent teeth (premolars, canines, and incisors) of 3 miniature swine were used. Class V cavities were prepared on the buccal surface of teeth. The cavities were restored with Biodentine in the presence (control group) or absence (experimental group) of a Dycal protective base. The pulpal tissue responses were histologically and histomorphometrically assessed at postoperative periods of 3 and 8 weeks. Three specimens were further evaluated with scanning electron microscopy. The maximum thickness of the postoperatively formed mineralized matrix beneath the cavity floor was measured. Data were statistically analyzed by the Kruskal-Wallis and the Mann-Whitney U tests. RESULTS: A bacterial staining reaction along the cavity walls or intense inflammatory infiltration in the pulp was not detected in any of the specimens. A continuous zone of the postoperatively formed mineralized matrix mostly of atubular structure with scattered defects and cellular inclusions and occasionally followed by a thin zone with tubular morphology was detected in all specimens of the control group and 13 of 18 experimental group teeth. In the remaining teeth of the experimental group, a separate zone composed of the osteotypic mineralized matrix and soft tissues was noted between the circumpulpal and the newly formed matrix. Scanning electron microscopy confirmed the fibrous structural morphology of the tertiary dentin. A significantly higher rate of the postoperatively formed mineralized matrix had been formed in the teeth of the experimental group in both periods of 3 and 8 weeks (P < .01). CONCLUSIONS: The present investigation indicates that under the present experimental conditions tertiary dentin with occasional intermediate formation of osteodentin is observed after the application of Biodentine in the presence or absence of a Dycal protective base. The thickness of the tertiary dentine zone was significantly higher in the absence of Dycal.

The influence of a novel in-office tooth whitening procedure using an Er,Cr:YSGG laser on enamel surface morphology.

BACKGROUND AND OBJECTIVE: The purpose of this in vitro study was to evaluate the influence of a novel in-office tooth whitening procedure using Er,Cr:YSGG laser radiation on bovine enamel. STUDY DESIGN/MATERIALS AND METHODS: Forty-eight enamel specimens were prepared from bovine canines and divided into four groups: Group 1 specimens (control) received no whitening treatment; Group 2 received whitening treatment with an at-home whitening agent (22% carbamide peroxide) for 7 days; Group 3 received whitening treatment with a novel in-office whitening agent (35% H(2)O(2)); Group 4 received the same in-office whitening therapy with Group 3 using Er,Cr:YSGG laser in order to accelerate the whitening procedure. The specimens were stored for 10 days after the whitening treatment in artificial saliva. Vickers hardness was determined using a microhardness tester and surface roughness was evaluated using a VSI microscope. Three specimens of each experimental group were examined under SEM and the mineral composition of the specimens was evaluated using EDS. Data were statistically analyzed using one-way ANOVA, Tukey's post-hoc test, Wilcoxon signed rank and Kruskal-Wallis tests (a = 0.05). RESULTS: The surface microhardness of the enamel was reduced after the in-office whitening treatments (P< 0.05), but not influenced after the at-home whitening treatment (P> 0.05). Moreover, the surface roughness was not significantly changed after tooth whitening. EDS analysis did not show alterations in the enamel mineral composition, while SEM observations indicated changes in the surface morphology, especially after in-office tooth whitening (P< 0.05). CONCLUSIONS: The laser-assisted whitening treatment with Er,Cr:YSGG laser did not affect the alterations in enamel surface compared with the conventional in-office whitening technique.

Effect of temperature, curing time, and filler composition on surface microhardness of composite resins.

AIM: The aim of this study was to evaluate the microhardness of two composite resins when subjected to three different temperatures and three different light-curing times. MATERIALS AND METHODS: Two composites were used; Filtek Z250 and Grandio. Three different temperatures (23, 37, and 55(o)C) were used, utilizing a composite warmer. The heated samples were immediately injected into cylindrical molds (6 mm × 2 mm) and the top surface of the specimens was polymerized for 10, 20, and 40 sec, using a Quartz-Tungsten-Halogen light-curing unit (QTH LCU). Vickers microhardness measurements were performed from both the top and bottom surface of the specimens, following dry storage for 24 hours in the dark. Statistical analysis were performed using one-way analysis of variance (ANOVA) and Tukey post-hoc test at a level of significance of a = 0.05. RESULTS: The results indicated that there was an increase in microhardness as the temperature of the composite was increased for either the top or the bottom surface (P < 0.05). Furthermore, there was a general increase in microhardness for both composites as curing time increased (P < 0.05). The type of composites did not influence the surface microhardness (P > 0.05). CONCLUSIONS: Temperature of composites affects their surface microhardness. Also, light-curing time influence microhardness values of the composites tested.

Dentinogenic responses after direct pulp capping of miniature swine teeth with Biodentine.

INTRODUCTION: The aim of this study was to evaluate pulpal responses after experimental direct pulp capping of mechanically exposed teeth with a new calcium silicate-based dentin replacement material. METHODS: Thirty-four anterior and posterior teeth of 3 miniature swine were used. Class V or I cavities were prepared on the buccal or occlusal surfaces, respectively. Pulpal exposures were further performed using a round carbide bur 0.8 mm in diameter. Exposures were treated with white MTA Angelus (Angelus, Londrina, PR, Brazil) or Biodentine (Septodont, Saint Maur des Fosses, France), and the cavities were further restored with Biodentine. The pulpal tissue responses were histologically assessed at postoperative periods of 3 and 8 weeks. Data were statistically analyzed using the Kruskal Wallis and the Mann-Whitney U tests. RESULTS: Inflammatory infiltration or pulp tissue necrosis was not found in any of the specimens. All teeth showed mineralized matrix formation in the form of a complete hard tissue bridge composed of osteodentin or osteodentin followed by a discontinuous or continuous reparative dentin zone. A significantly higher thickness of the hard tissue bridge was found in the group of teeth treated with Biodentine at both 3 and 8 weeks. A number of teeth, which were under root development at the onset of the experimental procedures, exhibited ectopic pulp calcification. CONCLUSIONS: The application of both calcium silicate-based materials in direct contact with the mechanically exposed pulp of healthy miniature swine teeth led to pulp repair with complete hard tissue bridge formation. The thickness of hard tissue bridges was significantly higher after pulp capping with Biodentine.

Accidental ingestion of an air-water syringe tip during routine dental treatment: a case report.

Accidental ingestion of instruments or their components is a possible complication of dental treatment. Although in many cases the foreign object can pass through the gastrointestinal tract without any need for surgical intervention to retrieve it, sometimes such incidents can be life-threatening. This paper reports a case of accidental ingestion of an air-water syringe tip during routine dental treatment for which endoscopic retrieval was required. The present case highlights the need for dental professionals to be aware of the fact that dental equipment comprising multiple components may be associated with a risk of accidental detachment of a component and its ingestion or aspiration by a patient receiving treatment.

The reparability of contemporary composite resins.

OBJECTIVE: The objective was to investigate the way that various surface treatments could influence the bond strength of the repair of methacrylate (MC) and silorane (SIL) composites. MATERIALS AND METHODS: A total of 160 MC and SIL cylindrical specimens were polymerized and aged in artificial saliva solution for 7 days. Depending on the following surface treatment (diamond bur or air abrasion), and the conditioning procedure (orthophosphoric acid or sodium hypochlorite), 16 groups were formed and repaired either with MC, either with SIL composite. Repaired specimens were subjected to an additional aging procedure in artificial saliva for 7 days, followed by thermo-cycling and then stressed in shear at a rate of 0.5 mm/min until failure. Failure patterns were analyzed using stereomicroscope and scanning electron microscopy. RESULTS: MC composite showed statistically significant higher bond strength both as a base or repair material than SIL (P < 0.001). Statistically significant differences were not observed, when grinding and conditioning procedures was compared. Pretest failures were observed when aged MC-based composite was repaired with SIL-based. CONCLUSIONS: Type of composite seems to be the main factor influencing the bond strength of the repair. MC-based composite showed better repairability than SIL composite. Optimum repair conditions should include knowledge of the composite's composition.

Effect of extraction media and storage time on the elution of monomers from four contemporary resin composite materials.

INTRODUCTION: The purpose of this study was to examine the effect of different extraction media, including culture media, as well as storage times on the elution of monomers from modern dental composites. MATERIALS AND METHODS: FOUR CONTEMPORARY COMPOSITE MATERIALS WERE TESTED: (a) Clearfil Majesty Esthetic (Kuraray), (b) Esthet X (DENTSPLY), (c) Filtek Silorane (3M ESPE), and (d) Admira (Voco). Forty-eight specimens were made. The specimens were stored in 1 ml of (a) artificial saliva, (b) Dulbecco's Modified Eagle Medium (DMEM), (c) DMEM plus 10% fetal bovine serum (FBS), and (d) ethanol 75%. The specimens were analyzed after 24 hours and after 1 week of storage. HPLC Liquid Chromatography was performed to analyze the extracted solutions. The statistical package SPSS 18 was used for the statistical analysis of the results. RESULTS: All the materials tested released monomers that were consistent with the base composition of their resin matrix. Bisphenol-A (BPA) was detected in Clearfil Esthetic and EsthetX when ethanol 75% was used for storage. TEGDMA was released at a faster rate compared to the other monomers with most of the monomer eluted in the first 24 hours. The effect of storage solution and storage time on the elution of the same monomers varied between materials. CONCLUSIONS: There was a significant effect of time, storage solution, and material on the elution of the detectable unbound monomers. Unbound monomers were detected in culture media, which may lead to false-negative results in cytotoxicity tests of resin composite materials. BPA was detected in two of the tested materials.

Shear bond strength of a "solvent-free" adhesive versus contemporary adhesive systems

AIM: To compare the shear bond strength (SBS) of a solvent free self-etch adhesive with solvent containing adhesives. METHODS: Forty-five human teeth were sectioned longitudinally to expose superficial dentin and substrates polished with 600-grit SiC paper. The adhesive area was isolated with a cylindrical Teflon mold 3x4 mm. Fifteen specimens were prepared for each material. Were evaluated a solvent free self-etch adhesive (Bond 1 SF), an ethanol self-etch adhesive (Futurabond M), and a water-acetone-ethanol self-etch adhesive (Optibond All-In-One). All specimens were subjected to an aging procedure by thermo-cycling (5000 cycles). Thirty-six specimens were stressed in shear at a rate of 0.5mm/min. Mean data values were analyzed statistically using the Welch robust analysis of variance and the Games-Howell statistic. Failure patterns were analyzed using stereomicroscope and scanning electron microscopy (SEM). Additional more dentin specimens were prepared for SEM. RESULTS: The Bond 1 SF showed the statistically significant lowest SBS to dentin (Welch statistic p<0.001). Failures for Bond 1 SF were mainly adhesive failures with partial cohesive failures in the adhesive resin, while for Futurabond M and Optibond All-In-One were mainly mixed. SEM findings confirm the results. CONCLUSIONS: Eliminating solvents from self-etch adhesive systems may decrease the bonding strength to dentin.

Fluoride release and recharge abilities of contemporary fluoride-containing restorative materials and dental adhesives.

The aim of this study was to evaluate the fluoride release of five fluoride-releasing restorative materials and three dental adhesives, before and after NaF solution treatment. Five restorative materials (Fuji IX GP, GC Corp.; Ketac N100, 3M ESPE; Dyract Extra, Dentsply; Beautifil II, Shofu Inc.; Wave, SDI) and three dental adhesives (Stae, SDI; Fluorobond II - Shofu Inc.; Prime & Bond NT, Dentsply) were investigated before and after NaF solution treatment. A fluoride ion-selective electrode was to measure fluoride concentrations. During the 86-day period before NaF solution treatment, Fuji IX GP released the highest amount of fluoride among the restorative materials while Prime & Bond NT was the highest among the dental adhesives. After NaF solution treatment, Fuji IX GP again ranked the highest in fluoride release among the restorative materials while Fluorobond II ranked the highest among dental adhesives. It was concluded that the compositions and setting mechanisms of fluoride-containing dental materials influenced their fluoride release and recharge abilities.

Temperature rise during photo-polymerization under ceramic restorations.

AIM: The aim of this study was to measure the temperature increase induced by various light-curing units during photo-polymerization beneath ceramic restorations. METHODS: Three light-curing units were used; a high intensity QTH unit Elipar 2500 and two LED units: Translux Power Blue and Excelled 1400. The 15 ceramic specimens (CEREC Blocks) used in this study were of 2.5 mm thickness, 5 mm wide and 6 mm long and made using a slow speed saw. Using the same slow speed saw the occlusal enamel portion of 15 mandibular third molars was removed and 15 dentin discs of 1 mm height were prepared. The thickness of the luting cement was delimited to 0.5 mm, using a Teflon mold and then brought into contact with the dentin disc. Light-curing time for all the groups was 20 sec. The temperature rise was measured placing underneath the dentin disc a K-type thermocouple wire connected to a data logger. Five measurements were carried out for each group. Statistical analysis was performed using ANOVA (a=0.05). RESULTS: The results indicated that there was a lower temperature rise induced from Translux Power Blue than from the other two light-curing units, which did not present statistically significant difference (p<0.05). However, temperature rise from the light-curing units used in this study is lower than 5.5°C, which is the limit of pulpal damage. CONCLUSIONS: Within the limitations of this study, although the type and characteristics of light-curing units may affect temperature rise under ceramic restorations, this influence is possibly not of clinical significance.

Pulp response to dentine adhesives: A study on mature human pulps.

OBJECTIVE: To clinically investigate the antibacterial effects of a commercially available self-etch 12-methacryloyloxy- dodecylpyridinium bromide (MDPB)-containing adhesive system in comparison with its respective non-MDPB-containing adhesive and to evaluate the pulp responses when in use on human teeth. MATERIALS AND METHODS: Sixty-two viable human teeth scheduled for extraction were used. Class V cavities were prepared on the buccal surfaces of the teeth and filled with the tested materials (Protect Bond/Clearfil AP-X, SE Bond/Clearfil AP-X and Dycal/Ketac Fill Plus) as a control group, according to manufacturer's recommendations. Randomly divided to two groups teeth remained intra-orally for 4 and 8 weeks. After extraction, teeth were decalcified, sectioned and stained using the Mayer's hematoxylin and eosin, and modified Brown-Brenn's technique. Pulp responses were evaluated microscopically under a microscope and remaining dentine thickness measured under a stereomicroscope. RESULTS: No statistically significant differences regarding pulp inflammation or bacterial infiltration were found either for the materials tested or for periods of post-operative evaluation. CONCLUSIONS: The results suggested that for a short period of evaluation there are no quantitative differences, regardless to restoring material used.

Bonding of adhesives to Er:YAG laser-treated dentin.

OBJECTIVE: The shear bond strength of adhesives applied to dentin was investigated after irradiation with an erbium-doped yttrium aluminum garnet (Er:YAG) laser. METHODS: Superficial and deep dentin specimens from human molars were treated either with carbide bur or an Er:YAG laser. Two etch and rinse adhesives (Single Bond and XP Bond) and two self-etch adhesives (Prompt L-Pop and Xeno III) were employed to bond the composite. Shear bond strength (SBS) was determined after storage in water for 24 h using a universal testing machine with a crosshead speed of 0.5 mm/min. Failure patterns and modes were analyzed and evaluated using a stereomicroscope. In addition, samples were processed for Scanning Electron Microscopy SEM evaluation. A linear mixed model was used, and pairwise comparisons were made using the Bonferroni test. RESULTS: Results showed significant differences between the levels of dentin treatment (p=.01) in carbide bur-cut dentin and lased dentin, as well as significant interaction effects due to the depth of dentin and the bonding system used. The etch and rinse adhesives bonded less effectively with lased dentin than with carbide bur-cut dentin, while self-etch adhesives bonded equally well with lased and bur-cut superficial dentin but much less effectively with lased deep dentin than with bur-cut deep dentin. SEM revealed a predominantly adhesive failure mode in laser-ablated fractured specimens, while a mixed failure mode was apparent in the bur-cut fractured specimens. CONCLUSIONS: Cavities prepared by laser seem less receptive to adhesive procedures than conventional bur-cut cavities.

Pulpal responses after application of current adhesive systems to deep cavities.

The aim of the present study was to evaluate comparatively the pulpal tissue reactions of four adhesive systems placed in experimental cavities of healthy dog's teeth. Class V cavities with a mean value of remaining dentin thickness (RDT) ranging between 0.55 +/- 0.30-0.68 +/- 0.38 mm were prepared. The cavities were treated with the following adhesive systems: Etch and Prime 3.0 (EP), Single Bond (SB), Clearfil SE Bond (CSE), and Prompt L-Pop (PLP). The pulpal tissue responses to dentin adhesives were assessed histopathologically at postoperative periods of 7, 21, and 65 days, and the results were subjected to statistical analysis. A significantly greater adverse inflammatory response was observed with the materials EP and PLP, while a significantly lesser degree of disorganization in the odontoblastic zone was found with the materials SB and CSE, in the postoperative period of 65 days. In addition, a thicker predentin zone was observed where SB material was applied. Application of the selected adhesive systems to non-exposed cavities, with an RDT, which ranged between the above-mentioned rates, was correlated with slight to moderate inflammation and odontoblast reduction depending on the materials used as well as upon the RDT.