RESUMO
MoS2 is a well-known 2D transition metal dichalcogenide (TMD) with feasibility for energy storage applications due to its eco-friendliness and high electroactive surface area. Electrodes based on MoS2 are typically made by either immobilizing its multiphase nanocomposites, having binders and conductive fillers, or by directly growing the materials on current collectors. In this work, we follow and optimize this latter approach by applying a hydrothermal route to directly synthesize MoS2 nanostructures on carbon cloth (MoS2@CC) hence enabling binder-free current collector electrodes. Raman spectroscopy and electron microscopy analyses confirmed the formation of 2H MoS2 nanosheets with hexagonal structure. The as-prepared electrodes were used to assemble symmetric supercapacitor cells, whose performance were tested in various types of electrolytes. Electrochemical measurements indicate that both precursor concentration and growth time significantly affect the device performance. Under optimized conditions, specific capacitance up to 226 F g-1 (at 1 A g-1 in 6 M KOH) was achieved, with corresponding energy and power densities of 5.1 W h kg-1 and 2.1 W kg-1. The device showed good stability, retaining 85% capacitance after 1000 cycles. Furthermore, the electrodes assessed in PYR14-TFSI showed energy and power densities of up to 26.3 W h kg-1 and 2.0 kW kg-1, respectively, indicating their feasibility not only in aqueous but also in ionic liquid electrolytes. In addition, galvanostatic charge/discharge measurements conducted on devices having footprint sizes from 1 cm2 to 25 cm2 show very similar specific capacitances, which proves scalability and thus the practical relevance of the binder-free electrodes demonstrated in this study.
RESUMO
MXenes are emerging sensing materials due to their metallic conductivity and rich surface chemistry for analytes; they, however, suffer from poor stability. Incorporation with functional polymers can largely prevent the performance decay and enhance the sensing performance. Herein, we demonstrate a core-shell composite, Ti3C2Tx@croconaine (poly(1,5-diaminonaphthalene-croconaine), PDAC) prepared by a facile in situ polymerization reaction, suitable for NH3 detection. Compared to pristine Ti3C2Tx, the sensor made of a Ti3C2Tx-polycroconaine composite exhibits a significantly enhanced sensitivity of 2.8% ppm-1 and an estimated achievable limit of detection of 50 ppb. The improved sensing performance could be attributed to the presence of PDAC facilitating the adsorption of NH3 and changing the tunneling conductivity between Ti3C2Tx domains. Density functional theory (DFT) calculations reveal that the adsorption energy of NH3 on PDAC is the highest among the tested gases, which supports the selectivity of the sensor to this analyte. Benefiting from the protection conferred by the PDAC shell, the composite has a reliable operation period of at least 40 days. In addition, we demonstrated a flexible paper-based sensor of the Ti3C2Tx@PDAC composite, without attenuated performance upon mechanical deformation. This work proposed a novel mechanism and a feasible methodology to synthesize MXene-polymer composites with improved sensitivity and stability for chemical sensing.
RESUMO
Cost-effective and high-performance H2S sensors are required for human health and environmental monitoring. 2D transition-metal carbides and nitrides (MXenes) are appealing candidates for gas sensing due to good conductivity and abundant surface functional groups but have been studied primarily for detecting NH3 and VOCs, with generally positive responses that are not highly selective to the target gases. Here, we report on a negative response of pristine Ti3C2Tx thin films for H2S gas sensing (in contrast to the other tested gases) and further optimization of the sensor performance using a composite of Ti3C2Tx flakes and conjugated polymers (poly[3,6-diamino-10-methylacridinium chloride-co-3,6-diaminoacridine-squaraine], PDS-Cl) with polar charged nitrogen. The composite, preserving the high selectivity of pristine Ti3C2Tx, exhibits an H2S sensing response of 2% at 5 ppm (a thirtyfold sensing enhancement) and a low limit of detection of 500 ppb. In addition, our density functional theory calculations indicate that the mixture of MXene surface functional groups needs to be taken into account to describe the sensing mechanism and the selectivity of the sensor in agreement with the experimental results. Thus, this report extends the application range of MXene-based composites to H2S sensors and deepens the understanding of their gas sensing mechanisms.
RESUMO
Integrated photodetectors based on transition metal dichalcogenides (TMDs) face the challenge of growing their high-quality crystals directly on chips or transferring them to the desired locations of components by applying multi-step processes. Herein, we show that vertically oriented polycrystalline thin films of MoS2 and WS2 grown by sulfurization of Mo and W sputtered on highly doped Si are robust solutions to achieve on-chip photodetectors with a sensitivity of up to 1 mA W-1 and an ultrafast response time in the sub-µs regime by simply probing the device in a vertical arrangement, i.e., parallel to the basal planes of TMDs. These results are two orders of magnitude better than those measured earlier in lateral probing setups having both electrodes on top of vertically aligned polycrystalline TMD films. Accordingly, our study suggests that easy-to-grow vertically oriented polycrystalline thin film structures may be viable components in fast photodetectors as well as in imaging, sensing and telecommunication devices.
RESUMO
H2S is a toxic and corrosive gas, whose accurate detection at sub-ppm concentrations is of high practical importance in environmental, industrial, and health safety applications. Herein, we propose a chemiresistive sensor device that applies a composite of single-walled carbon nanotubes (SWCNTs) and brominated fullerene (C60Br24) as a sensing component, which is capable of detecting 50 ppb H2S even at room temperature with an excellent response of 1.75% in a selective manner. In contrast, a poor gas response of pristine C60-based composites was found in control measurements. The experimental results are complemented by density functional theory calculations showing that C60Br24 in contact with SWCNTs induces localized hole doping in the nanotubes, which is increased further when H2S adsorbs on C60Br24 but decreases in the regions, where direct adsorption of H2S on the nanotubes takes place due to electron doping from the analyte. Accordingly, the heterogeneous chemical environment in the composite results in spatial fluctuations of hole density upon gas adsorption, hence influencing carrier transport and thus giving rise to chemiresistive sensing.
RESUMO
The continuously growing number of short-life electronics equipment inherently results in a massive amount of problematic waste, which poses risks of environmental pollution, endangers human health, and causes socioeconomic problems. Hence, to mitigate these negative impacts, it is our common interest to substitute conventional materials (polymers and metals) used in electronics devices with their environmentally benign renewable counterparts, wherever possible, while considering the aspects of functionality, manufacturability, and cost. To support such an effort, in this study, we explore the use of biodegradable bioplastics, such as polylactic acid (PLA), its blends with polyhydroxybutyrate (PHB) and composites with pyrolyzed lignin (PL), and multiwalled carbon nanotubes (MWCNTs), in conjunction with processes typical in the fabrication of electronics components, including plasma treatment, dip coating, inkjet and screen printing, as well as hot mixing, extrusion, and molding. We show that after a short argon plasma treatment of the surface of hot-blown PLA-PHB blend films, percolating networks of single-walled carbon nanotubes (SWCNTs) having sheet resistance well below 1 kΩ/â¡ can be deposited by dip coating to make electrode plates of capacitive touch sensors. We also demonstrate that the bioplastic films, as flexible dielectric substrates, are suitable for depositing conductive micropatterns of SWCNTs and Ag (1 kΩ/â¡ and 1 Ω/â¡, respectively) by means of inkjet and screen printing, with potential in printed circuit board applications. In addition, we exemplify compounded and molded composites of PLA with PL and MWCNTs as excellent candidates for electromagnetic interference shielding materials in the K-band radio frequencies (18.0-26.5 GHz) with shielding effectiveness of up to 40 and 46 dB, respectively.
RESUMO
Printed piezoresistive strain sensors based on stretchable roll-to-roll screen-printed silver electrodes on polydimethylsiloxane substrates and inkjet-deposited single-wall carbon nanotube micropatterns are demonstrated in this work. With the optimization of surface wetting and inkjet printing parameters, well-defined microscopic line patterns of the nanotubes with a sheet resistance of <100 Ω/â¡ could be deposited between stretchable Ag electrodes on the plasma-treated substrate. The developed stretchable devices are highly sensitive to tensile strain with a gauge factor of up to 400 and a pressure sensitivity of â¼0.09 Pa-1, respond to bending down to a radius of 1.5 mm, and are suitable for mounting on the skin to monitor and resolve various movements of the human body such as cardiac cycle, breathing, and finger flexing. This study indicates that inkjet deposition of nanomaterials can complement well other printing technologies to produce flexible and stretchable devices in a versatile manner.
RESUMO
Several different methods are established for the analysis of gases, including optical spectroscopy, photoacoustic spectroscopy as well as colorimetric and resistive sensing, the measurements systems are either too complex or have limited sensitivity. In particular, when the goal is to apply a large number of sensors in networks, it is highly desirable to have devices that are simple, have low cost and energy consumption, yet sensitive and selective to monitor analytes even in traces. Herein, we propose a new type of resistive sensor device based on a composite of single-wall carbon nanotubes and an ion-in-conjugation polymer, poly(1,5-diaminonaphthalene-squaraine), capable of detecting H2S and NH3 in air even at room temperature with a theoretical concentration limit of â¼1 ppb and â¼7 ppb, respectively. Density functional theory calculations revealed that H atoms of the analytes and O atoms of the polymer chain interact and form hydrogen bonds, and the electron withdrawal from the gas molecules by the polymer chain results in the change of its electrical conductivity. To demonstrate the feasibility of the new nanocomposites in sensing, we show the devices for monitoring food safety with good sensor stability of operation for at least 3 months of period of time.
RESUMO
Several different methods are established for the analysis of gases, including optical spectroscopy, photoacoustic spectroscopy as well as colorimetric and resistive sensing, the measurements systems are either too complex or have limited sensitivity. In particular, when the goal is to apply a large number of sensors in networks, it is highly desirable to have devices that are simple, have low cost and energy consumption, yet sensitive and selective to monitor analytes even in traces. Herein, we propose a new type of resistive sensor device based on a composite of single-wall carbon nanotubes and an ion-in-conjugation polymer, poly(1,5-diaminonaphthalene-squaraine), capable of detecting H2S and NH3in air even at room temperature with a theoretical concentration limit of ~1 ppb and ~7 ppb, respectively. Density functional theory calculations revealed that H atoms of the analytes and O atoms of the polymer chain interact and form hydrogen bonds, and the electron withdrawal from the gas molecules by the polymer chain results in the change of its electrical conductivity. To demonstrate the feasibility of the new nanocomposites in sensing, we show the devices for monitoring food safety with good sensor stability of operation for at least 3 months of period of time.
RESUMO
There is ever increasing demand for flexible energy storage devices due to the development of wearable electronics and other small electronic devices. The electrode flexibility is best provided by a special set of nanomaterials, but the required methodology typically consists of multiple steps and are designed just for the specific materials. Here, a facile and scalable method of making flexible and mechanically robust planar supercapacitors with interdigital electrode structure made of commercial carbon nanomaterials and silver nanowires is presented. The capacitor structure is achieved with vacuum filtration through a micropatterned contact mask and finished with simple laser processing steps. A maximum specific capacitance of 4 F cm-3 was measured with cyclic voltammetry at scan rate of 5 mV s-1. The reliability and charge transfer properties of devices were further investigated with galvanostatic charge-discharge measurements and electrochemical impedance spectroscopy, respectively. Furthermore, mechanical bending tests confirmed the devices have excellent mechanical integrity, and the deformations have no adverse effects on the electrochemical charge-discharge behavior and stability.
RESUMO
The continuously increasing demand for faster data traffic of our telecommunication devices requires new and better materials and devices that operate at higher frequencies than today. In this work, a porous composite of silica nanoshells and cellulose nanofibers is demonstrated as a suitable candidate of dielectric substrates to be used in future 6G frequency bands. The hollow nanospheres of amorphous SiO2 with outstanding electromagnetic properties were obtained by a template-assisted Stöber process, in which a thin shell of silica is grown on polystyrene nanospheres first, and then the polymer core is burned off in a subsequent step. To be able to produce substrates with sufficient mechanical integrity, the nanoshells of SiO2 were reinforced with cellulose nanofibers resulting in a porous composite of very low mass density (0.19 ± 0.02 g cm-3), which is easy to press and mold to form films or slabs. The low relative dielectric permittivity (ε r = 1.19 ± 0.01 at 300 GHz and ε r = 1.17 ± 0.01 at 2.0 THz) and corresponding loss tangent (tan δ= 0.011 ± 0.001 at 300 GHz and tan δ = 0.011 ± 0.001 at 2.0 THz) of the composite films are exploited in substrates for radio frequency filter structures designed for 300 GHz operation.
RESUMO
Transparent conductive films are used in a wide variety of devices. While solar cell top electrodes as well as tablet and mobile phone screens require high optical transparency and low sheet resistance (>80% and <10 Ω/â¡) to maximize power efficiency; other, less demanding applications, such as those in capacitive touch panels and antistatic coatings, in which only small currents are involved, can be managed with coatings of moderate conductivity. In this paper, we show that area-selective argon plasma treated polyethylene terephthalate surfaces are suitable for localized deposition of carbon nanotubes from their aqueous dispersions by a simple dip coating and subsequent drying processes. The as-deposited carbon nanotubes form entangled networks in microscopic patterns over the plasma-treated surface areas with sheet resistance of <1 kΩ/â¡ and optical transparency of ~75%. Based on this process, we demonstrate grid-type transparent conductive thin films of carbon nanotubes as capacitive touch sensors. Since each process step is robust, easy to up and downscale, and may be implemented even in roll-to-roll and sheet-to-sheet fabrication, the demonstrated technology is promising to produce grid-type structures even at an industrial scale in the future.
RESUMO
Construction of colloidal nanoparticles (NPs) into advanced functional nanocomposites and hybrids with the predesigned hierarchical structure and high-performance is attractive, especially for natural biological nanomaterials, such as proteins and polysaccharides. Herein, a simple and sustainable approach called interfacial NP complexation (INC) was applied to construct diverse functional (conductive, drug-loaded, or antimicrobial) nanocomposite filaments from oppositely charged colloidal nanocelluloses. By incorporating different additives during the INC process, including multiwalled carbon nanotube, an antitumor drug (doxorubicin hydrochloride), and metal (silver) NPs (Ag NPs), high-performance functional continuous filaments were synthesized, and their potential applications in electronics, drug delivery, and antimicrobial materials were investigated, respectively. This novel INC method based on charged colloidal NPs opens new avenues for building various functional filaments for a diversity of end uses.
Assuntos
Sistemas de Liberação de Medicamentos , Liberação Controlada de Fármacos , Nanopartículas Metálicas/química , Nanotubos de Carbono/química , Prata/química , Anti-Infecciosos/síntese química , Anti-Infecciosos/química , Antineoplásicos/química , Antineoplásicos/farmacologia , Doxorrubicina/química , Doxorrubicina/farmacologia , Condutividade Elétrica , Humanos , Neoplasias/tratamento farmacológico , Neoplasias/patologiaRESUMO
Transition metal dichalcogenides (TMDs) have received immense research interest in particular for their outstanding electrochemical and optoelectrical properties. Lately, chemical gas sensor applications of TMDs have been recognized as well owing to the low operating temperatures of devices, which is a great advantage over conventional metal oxide based sensors. In this work, we elaborate on the gas sensing properties of WS2 and MoS2 thin films made by simple and straightforward thermal sulfurization of sputter deposited metal films on silicon chips. The sensor response to H2, H2S, CO and NH3 analytes in air at 30 °C has been assessed and both MoS2 and WS2 were found to have an excellent selectivity to NH3 with a particularly high sensitivity of 0.10 ± 0.02 ppm-1 at sub-ppm concentrations in the case of WS2. The sensing behavior is explained on the bases of gas adsorption energies as well as carrier (hole) localization induced by the surface adsorbed moieties having reductive nature.
RESUMO
High-performance electromagnetic interference shielding is becoming vital for the next generation of telecommunication and sensor devices among which portable and wearable applications require highly flexible and lightweight materials having efficient absorption-dominant shielding. Herein, we report on lightweight carbon foam-carbon nanotube/carbon nanofiber nanocomposites that are synthesized in a two-step robust process including a simple carbonization of open-pore structure melamine foams and subsequent growth of carbon nanotubes/nanofibers by chemical vapor deposition. The microstructure of the nanocomposites resembles a 3-dimensional hierarchical network of carbonaceous skeleton surrounded with a tangled web of bamboo-shaped carbon nanotubes and layered graphitic carbon nanofibers. The microstructure of the porous composite enables absorption-dominant (absorbance â¼0.9) electromagnetic interference shielding with an effectiveness of â¼20-30 dB and with an equivalent mass density normalized shielding effectiveness of â¼800-1700 dB cm3 g-1 at the K-band frequency (18-26.5 GHz). Moreover, the hydrophobic nature of the materials grants water-repellency and stability in humid conditions important for reliable operation in outdoor use, whereas the mechanical flexibility and durability with excellent piezoresistive behavior enable strain-responsive tuning of electrical conductivity and electromagnetic interference shielding, adding on further functionalities. The demonstrated nanocomposites are versatile and will contribute to the development of reliable devices not only in telecommunication but also in wearable electronics, aerospace engineering, and robotics among others.
RESUMO
Catalyst size affects the overall kinetics and mechanism of almost all heterogeneous chemical reactions. Since the functional sensing materials in resistive chemical sensors are practically the very same nanomaterials as the catalysts in heterogeneous chemistry, a plausible question arises: Is there any effect of the catalyst size on the sensor properties? Our study attempts to give an insight into the problem by analyzing the response and sensitivity of resistive H2 sensors based on WO3 nanowire supported Pt nanoparticles having size of 1.5±0.4 nm, 6.2±0.8 nm, 3.7±0.5 nm and 8.3±1.3 nm. The results show that Pt nanoparticles of larger size are more active in H2 sensing than their smaller counterparts and indicate that the detection mechanism is more complex than just considering the number of surface atoms of the catalyst.
RESUMO
Unmodified and multi-walled carbon nanotube (MWCNT) modified tetrahedral amorphous carbon (ta-C) films of 15 and 50â¯nm were investigated as potential in vivo sensor materials for the detection of dopamine (DA) in the presence of the main interferents, ascorbic acid (AA) and uric acid (UA). The MWCNTs were grown directly on ta-C by chemical vapor deposition (designated as ta-C+CNT) and were characterized with X-ray photoelectron spectroscopy, Raman spectroscopy, scanning and transmission electron microscopy. Electroanalytical sensitivity and selectivity were determined with cyclic voltammetry. Biocompatibility of the materials was assessed with cell cultures of mouse neural stem cells (mNSCs). The detection limits of DA for both ta-C and ta-C+CNT electrodes ranged from 40 to 85â¯nM, which are well within the required range for in vivo detection. The detection limits were lower for both ta-C and ta-C+CNT electrodes with 50â¯nm of ta-C compared to 15â¯nm. The ta-C electrodes showed a large dynamic linear range of 0.01-100⯵M but could not resolve between the oxidation peaks of DA, AA and UA. Modification with MWCNTs, however, resulted in excellent selectivity and all three analytes could be detected simultaneously at physiologically relevant concentrations using cyclic voltammetry. Based on cell culture of mNSCs, both ta-C and ta-C+CNT exhibited good biocompatibility, demonstrating their potential as in vivo sensor materials for the detection of DA.
Assuntos
Técnicas Biossensoriais/métodos , Carbono/química , Dopamina/análise , Nanotubos de Carbono/química , Animais , Ácido Ascórbico , Eletrodos , Camundongos , Ácido ÚricoRESUMO
The rapid oxide formation on pristine unprotected copper surfaces limits the direct application of Cu nanomaterials in electronics and sensor assemblies with physical contacts. However, it is not clear whether the growing cuprous (Cu2O) and cupric oxides (CuO) and the formation of core-shell-like Cu-Cu2O/CuO nanowires would cause any compromise for non-contact optical measurements, where light absorption and subsequent charge oscillation and separation take place such as those in surface plasmon-assisted and photocatalytic processes, respectively. Therefore, we analyze how the surface potential of hydrothermally synthetized copper nanowires changes as a function of time in ambient conditions using Kelvin probe force microscopy in dark and under light illumination to reveal charge accumulation on the nanowires and on the supporting gold substrate. Further, we perform finite element modeling of the optical absorption to predict plasmonic behavior of the nanostructures. The results suggest that the core-shell-like Cu-Cu2O/CuO nanowires may be useful both in photocatalytic and in surface plasmon-enhanced processes. Here, by exploiting the latter, we show that regardless of the native surface oxide formation, random networks of the nanowires on gold substrates work as excellent amplification media for surface-enhanced Raman spectroscopy as demonstrated in sensing of Rhodamine 6G dye molecules.