RESUMO
BACKGROUND: Continuous kidney replacement therapy (CKRT) has recently become the preferred kidney replacement modality for children with acute kidney injury (AKI). We hypothesise that CKRT technical parameters and treatment settings in addition to the clinical characteristics of patients may influence the circuit lifetime in children. METHODS: The study involved children included in the EurAKId registry (NCT02960867), who underwent CKRT treatment. We analysed patient characteristics and CKRT parameters. The primary end point was mean circuit lifetime (MCL). Secondary end points were number of elective circuit changes and occurrence of dialysis-related complications. RESULTS: The analysis was composed of 247 children who underwent 37,562 h of CKRT (median 78, IQR 37-165 h per patient). A total of 1357 circuits were utilised (3, IQR 2-6 per patient). MCL was longer in regional citrate anticoagulation (RCA), compared to heparin (HA) and no anticoagulation (NA) (42, IQR 32-58 h; 24, IQR 14-34 h; 18, IQR 12-24 h, respectively, p < 0.001). RCA was associated with longer MCL regardless of the patient's age or dialyser surface. In multivariate analysis, MCL correlated with dialyser surface area (beta = 0.14, p = 0.016), left internal jugular vein vascular access site (beta = -0.37, p = 0.027), and the use of HA (beta = -0.14, p = 0.038) or NA (beta = -0.37, p < 0.001) vs. RCA. RCA was associated with the highest ratio of elective circuit changes and the lowest incidence of complications. CONCLUSION: Anticoagulation modality, dialyser surface, and vascular access site influence MCL. RCA should be considered when choosing first-line anticoagulation for CKRT in children. Further efforts should focus on developing guidelines and clinical practice recommendations for paediatric CKRT.
RESUMO
Jute fibers are characterized by a heterogeneous chemical composition (cellulose and non-cellulosic components) and a complex layered structure with a hydrophobic surface outer layer responsible for their low wettability. In this work, after the removal of water-soluble components, raw jute fibers were subjected to atmospheric pressure dielectric barrier discharge (DBD) under different conditions (at 150 or 300 Hz) to tailor jute fiber surface structure and wettability. The research was focused on the aging effect during natural aging in a standard atmosphere investigated up to three weeks after DBD treatment. Alterations in the surface morphology of DBD-treated jute fibers were investigated by FE-SEM and AFM, while ATR-FTIR, XPS, and electrokinetic measurements were used to assess the changes in the jute fiber surface chemistry. Sorption properties were monitored through wetting time and capillary rise measurements. The sorption properties of DBD-treated jute fibers were improved (about 100 times lower wetting time and 15 % higher capillary rise height in comparison to untreated) due to the changes in surface chemistry (decreased lignin and hemicellulose content in parallel with cellulose oxidation) and morphology (about 4.6 times higher average roughness). The electrokinetic and sorption properties measurement confirmed the significance of aging effects in lignocellulosic fibers' functionalization using plasma.
RESUMO
A series of novel films based on TEMPO-oxidized chitosan nanoparticles were prepared by casting method. Fourier transform infrared spectroscopy (FTIR) was employed to ascertain the chemical structure of TEMPO-oxidized chitosan. The surface morphology of the TEMPO-oxidized chitosan nanoparticles was analyzed by atomic force microscopy (AFM). The physicochemical (area density, thickness, iodine sorption, roughness), functional (moisture sorption, liquid absorption capacity, weight loss upon contact with the liquid, and water vapor transmission rate), antibacterial, and antioxidant properties of films based on TEMPO-oxidized chitosan nanoparticles were also investigated. The physicochemical properties of the films varied widely: area density ranged from 77.83 ± 0.06 to184.46 ± 0.05 mg/cm2, thickness varied between 80.5 ± 1.6 and 200.5 ± 1.6 µm, iodine sorption spanned from 333.7 ± 2.1 to166.4 ± 2.2 mg I2/g, and roughness ranged from 4.1 ± 0.2 to 5.6 ± 0.3 nm. Similarly, the functional properties also varied significantly: moisture sorption ranged from 4.76 ± 0.03 to 9.62 ± 0.11 %, liquid absorption capacity was between 129.04 ± 0.24 and 159.33 ± 0.73 % after 24 h, weight loss upon contact with the liquid varied between 31.06 ± 0.35 and 45.88 ± 0.58 % after 24 h and water vapor transmission rate ranged from 1220.10 ± 2.91to1407.77 ± 5.22 g/m2 day. Despite the wide variations in physicochemical and functional properties, all films showed maximum bacterial reduction of Staphylococcus aureus and Escherichia coli, although they exhibited low antioxidant activity. The results suggest that the films could be effectively utilized as antibacterial wound dressings.
Assuntos
Antibacterianos , Antioxidantes , Bandagens , Quitosana , Óxidos N-Cíclicos , Escherichia coli , Nanopartículas , Oxirredução , Staphylococcus aureus , Quitosana/química , Nanopartículas/química , Antibacterianos/química , Antibacterianos/farmacologia , Staphylococcus aureus/efeitos dos fármacos , Escherichia coli/efeitos dos fármacos , Antioxidantes/química , Antioxidantes/farmacologia , Óxidos N-Cíclicos/química , Testes de Sensibilidade MicrobianaRESUMO
This paper outlines a novel simple protocol for tuning the structure and properties of jute using sodium periodate (NaIO4) oxidation and coating with alginate. When compared to the raw jute, fabrics oxidized with a 0.2 or 0.4 % NaIO4 solution for 30-120 min exhibited an increased aldehyde group content (0.185 vs. 0.239-0.398 mmol/g), a significantly increased negative zeta potential (from -8.57 down to -20.12 mV), a slight disruption of fiber crystallinity, 15.1-37.5 % and 27.9-49.8 % lower fabric maximum force and stiffness, respectively. Owing to the removal of hydrophobic surface barrier, decreased crystallinity index and the presence of micropores on the fabrics' surfaces, oxidized fabrics have a 22.3-29.6 % improved ability for moisture sorption compared to raw fabric. Oxidized fabrics characterized by very long wetting times and excellent antioxidant activities (> 98 %), can find applications as hydrophobic packaging materials. To further extend the utilization of jute in biocarpet engineering such as water-binding geo-prebiotic supports, oxidized fabrics were coated with alginate resulting in 7.9-24.9 % higher moisture sorption and 352-660 times lower wetting times than their oxidized counterparts. This modification protocol has never been applied to lignocellulosic fibers and sheds new light on obtaining jute fabrics with tuned structure and properties intended for various applications.
Assuntos
Alginatos , Alginatos/química , Ácido Periódico , Oxirredução , Interações Hidrofóbicas e HidrofílicasRESUMO
Hemicellulose and pectin are noteworthy components of historical European rag papers, and have not been studied in detail so far. Rag papers were made from used textiles, and fiber-based utilities, such as ropes and bags. These had been prepared until the mid-19th century from plant-based fibers. Their polysaccharide composition could relate to their condition and history. This information can be expected to hold importance for the preservation and conservation of historical objects. We investigated a collection of rag papers of different age for their composition of non-cellulosic polysaccharides, and compared the findings with modern rag papers and wood pulps. Furthermore, a non-destructive determination of the hemicellulose and pectin content by near-infrared spectroscopy was developed. Historical rag papers had a lower hemicellulose/pectin content than pulps; the fractions of rhamnose, galactose, and arabinose were higher, while xylose was lower. In modern rag papers, xylose tended to be at the higher end of the range, which suggests a degradation of hemicelluloses/pectin over time or a change in raw materials and manufacturing. Rag papers also showed higher crystallinity than wood pulp papers. These findings provide insights into rag paper characteristics and offer potential classification methods.
Assuntos
Polissacarídeos , Xilose , Xilose/metabolismo , Polissacarídeos/química , Pectinas/metabolismo , Madeira/química , Arabinose/análiseRESUMO
Ionic liquid 1-butyl-3-methylimidazolium chloride [BMIM][Cl] was used to prepare cellulose (CELL), cellulose/polycaprolactone (CELL/PCL), cellulose/polycaprolactone/keratin (CELL/PCL/KER), and cellulose/polycaprolactone/keratin/ground calcium carbonate (CELL/PCL/KER/GCC) biodegradable mulch films. Attenuated Total Reflectance Fourier-Transform Infrared (ATR-FTIR) spectroscopy, optical microscopy, and Field-Emission Scanning Electron Microscopy (FE-SEM) were used to verify the films' surface chemistry and morphology. Mulch film made of only cellulose regenerated from ionic liquid solution exhibited the highest tensile strength (75.3 ± 2.1 MPa) and modulus of elasticity of 944.4 ± 2.0 MPa. Among samples containing PCL, CELL/PCL/KER/GCC is characterized by the highest tensile strength (15.8 ± 0.4 MPa) and modulus of elasticity (687.5 ± 16.6 MPa). The film's breaking strain decreased for all samples containing PCL upon the addition of KER and KER/GCC. The melting temperature of pure PCL is 62.3 °C, whereas that of CELL/PCL film has a slight tendency for melting point depression (61.0 °C), which is a characteristic of partially miscible polymer blends. Furthermore, Differential Scanning Calorimetry (DSC) analysis revealed that the addition of KER or KER/GCC to CELL/PCL films resulted in an increment in melting temperature from 61.0 to 62.6 and 68.9 °C and an improvement in sample crystallinity by 2.2 and 3.0 times, respectively. The light transmittance of all studied samples was greater than 60%. The reported method for mulch film preparation is green and recyclable ([BMIM][Cl] can be recovered), and the inclusion of KER derived by extraction from waste chicken feathers enables conversion to organic biofertilizer. The findings of this study contribute to sustainable agriculture by providing nutrients that enhance the growth rate of plants, and hence food production, while reducing environmental pressure. The addition of GCC furthermore provides a source of Ca2+ for plant micronutrition and a supplementary control of soil pH.
RESUMO
Congenital anomalies of the kidney and urinary tract (CAKUT) represent structural and functional urinary system malformations and take place as one of the most common congenital malformations with an incidence of 1:500. Ureteral obstruction-induced hydronephrosis is associated with renal fibrosis and chronic kidney diseases in the pediatric CAKUT. We aimed to construct interaction network of previously bioinformatically associated miRNAs with CAKUT differentially expressed genes in order to prioritize those associated with fibrotic process and to experimentally validate the expression of selected miRNAs in CAKUT patients compared to control group. We constructed interaction network of hsa-miR-101-3p, hsa-miR-101-5p and hsa-miR-29c-3p that showed significant association with fibrosis. The top enriched molecular pathway was extracellular matrix-receptor interaction (adjusted p = .0000263). We experimentally confirmed expression of three miRNAs (hsa-miR-29c-3p, hsa-miR-101-3p and hsa-miR-101-5p) in obstructed ureters (ureteropelvic junction obstruction and primary obstructive megaureter) and vesicoureteral reflux. The hsa-miR-29c-3p was shown to have lower expression in both patient groups compared to controls. Relative levels of hsa-miR-101-5p and hsa-miR-101-3p showed significant positive correlations in both groups of patients. Statistically significant correlation was observed between hsa-miR-101 (-3p and -5p) and hsa-miR-29c-3p only in the obstructed group. The significant downregulation of anti-fibrotic hsa-miR-29c-3p in obstructive CAKUT could explain activation of genes involved in fibrotic processes. As miRNAs are promising candidates in therapeutic approaches our results need further measurement of fibrotic markers or assessment of extent of fibrosis and functional evaluation of hsa-miR-29c.
Assuntos
MicroRNAs , Sistema Urinário , Humanos , Criança , Regulação para Baixo , Perfilação da Expressão Gênica , MicroRNAs/genética , MicroRNAs/metabolismo , Fibrose , Rim/metabolismo , Sistema Urinário/metabolismoRESUMO
This study aimed to obtain functional viscose textiles based on chitosan coatings with improved antibacterial properties and washing durability. For that reason, before functionalization with chitosan/zinc nanoparticles (NCH+Zn), the viscose fabric was modified by nonthermal gas plasma of dielectric barrier discharge (DBD) to introduce into its structure functional groups suitable for attachment of NCH+Zn. NCH+Zn were characterized by measurements of hydrodynamic diameter and zeta potential and AFM. DBD-plasma-modified and NCH+Zn-functionalized fabrics were characterized by zeta potential measurements, ATR-FTIR spectroscopy, the calcium acetate method (determination of content of carboxyl and aldehyde groups), SEM, breaking-strength measurements, elemental analysis, and ICP-OES. Their antibacterial activity was determined under dynamic contact conditions. In addition to SEM, the NCH+Zn distributions on viscose fabrics were also indirectly characterized by measuring their absorbent capacities before and after functionalization with NCH+Zn. Washing durability was monitored through changes in the zeta potential, chitosan and zinc content, and antibacterial activity after 1, 3, and 5 washing cycles. The obtained results showed that DBD plasma modification contributed to the simultaneous improvement of NCH+Zn sorption and antibacterial properties of the viscose fabric functionalized with NCH+Zn, and its washing durability, making it suitable for the production of high-value-added medical textiles.
RESUMO
A diluted ethanol orange peel extract was used for sustainable dyeing and functionalization of different fabrics. The extract analysis was performed using UPLC-ESI-MS/MS; its total flavonoid (0.67 g RE/100 g d.w.) and antioxidant (2.81 g GAE/100 g d.w.) contents and antioxidant activity (IC50 of 65.5 µg/mL) were also determined. The extract dyeing performance at various dyebath pH values was evaluated using multifiber fabric. Among six fabrics, extract possessed the ability for dyeing wool, polyamide, and cellulose acetate (at pH 4.5), which color strength (K/S) values increased after washing (9.7-19.8 vs. 11.6-23.2). Extract:water ratio of 20:35 (v/v) was found to be sufficient for achieving satisfactory K/S values (i.e., 20.17, 12.56, and 10.38 for wool, polyamide, and cellulose acetate, respectively) that were slightly changed after washing. The optimal dyeing temperatures for wool, polyamide, and cellulose acetate are 55, 35, and 25 °C, while the equilibrium dye exhaustion at those temperatures was achieved after 45, 120, and 90 min, respectively. The color coordinate measurements revealed that wool and polyamide fabrics are yellower than cellulose acetate, while, compared to polyamide and cellulose acetate, wool is redder. Possible interactions between selected fabrics and extract compounds are suggested. All fabrics possessed excellent antioxidant activity (88.6-99.6%) both before and after washing. Cellulose acetate provided maximum bacterial reduction (99.99%) for Escherichia coli, and Staphylococcus aureus, which in the case of Staphylococcus aureus remained unchanged after washing. Orange peel extract could be used for simultaneous dyeing and functionalization of wool and polyamide (excellent antioxidant activity) and cellulose acetate (excellent antioxidant and antibacterial activity) fabrics.
RESUMO
Gaseous acetic acid is formed under conditions of storage of historic paper objects. Its presence not only promotes hydrolytic cleavage of cellulose, but also causes acetylation of the cellulosic material to very small degree. The acetylation reaction proceeds under ambient conditions and without catalyst. Different analytical methods were used to prove the presence of organic acetates on cellulosic paper matrices. DESI-MS in combination with 2H-isotopic labeling showed the presence of sugar fragments with different acetylation patterns. A method based on Zemplen saponification was applied and worked also in the presence of a large excess of acetic acid and/or inorganic acetates. The acetylation effect was quantified for model papers and original, naturally aged paper samples. While cellulose acetylation was clearly proven to be another general pathway of paper aging, further studies of this acetylation phenomenon are needed with regard to conservational aspects and suitable paper storage conditions.
Assuntos
Acetatos , Celulose , Acetilação , LivrosRESUMO
The study aimed to discriminate renal allografts with impaired function by measuring cortical renal blood flow (cRBF) using magnetic resonance imaging arterial spin labelling (ASL-MRI) in paediatric and young adult patients. We included 18 subjects and performed ASL-MRI on 1.5 T MRI to calculate cRBF on parameter maps. cRBF was correlated to calculated glomerular filtration rate (GFR) and compared between patient groups with good (GFR ≥ 60 mL/min/1.73 m2) and impaired allograft function (GFR < 60 mL/min/1.73 m2). Mean cRBF in patients with good allograft function was significantly higher than in patients with impaired allograft function (219.89 ± 57.24 mL/min/100 g vs. 146.22 ± 41.84 mL/min/100 g, p < 0.008), showing a highly significant correlation with GFR in all subjects (r = 0.75, p < 0.0001). Also, the diffusion-weighted imaging (DWI-MRI) apparent diffusion coefficient (ADC) and Doppler measurements of peak-systolic and end-diastolic velocities and the resistive index (PS, ED, RI) were performed and both methods showed no significant difference between groups. ADC implied no correlation with GFR (r = 0.198, p = 0.464), while PS indicated moderate correlation to GFR (r = 0.48, p < 0.05), and PS and ED moderate correlation to cRBF (r = 0.58, p < 0.05, r = 0.56, p < 0.05, respectively). Cortical perfusion as non-invasively measured by ASL-MRI differs between patients with good and impaired allograft function and correlates significantly with its function.
Assuntos
Aloenxertos/diagnóstico por imagem , Aloenxertos/fisiopatologia , Imagem de Difusão por Ressonância Magnética/métodos , Falência Renal Crônica/fisiopatologia , Transplante de Rim , Imageamento por Ressonância Magnética/métodos , Circulação Renal/fisiologia , Transplante Homólogo , Adolescente , Adulto , Criança , Diástole , Feminino , Taxa de Filtração Glomerular , Humanos , Córtex Renal/irrigação sanguínea , Córtex Renal/diagnóstico por imagem , Falência Renal Crônica/cirurgia , Masculino , Sístole , Adulto JovemRESUMO
BACKGROUND: Acute kidney injury (AKI), particularly that requiring dialysis, is a severe complication in hospitalized children that is associated with high morbidity and mortality. A prospective European AKI registry (EurAKId registry, NCT02960867) was created to describe the epidemiology and outcomes of paediatric patients treated with acute dialysis. METHODS: Children were recruited who were between 0 and 18 years of age and were treated both in and outside the paediatric intensive care unit (PICU) with peritoneal dialysis (PD), haemodialysis (HD) or continuous kidney replacement therapy (CKRT) for AKI or metabolic derangement, fluid overload (FO), sepsis or respiratory distress. Five age groups and 12 categories of primary diseases were defined. RESULTS: Data on 340 patients were analysed, of whom 86% received dialysis for AKI and 14% for reasons other than AKI. Boys accounted for 60% of the patients. Illness severity was greater in children with cardiac and haematologic diseases than those with kidney diseases. Most patients received dialysis in the PICU (84%). The most frequently used dialysis modality was CKRT (64%), followed by PD (14%) and HD (14%). The overall survival rate was 65%. Survival was significantly lower in children with three comorbidities than in children with no comorbidities (41% and 83%; P < 0.001). CONCLUSIONS: The EurAKId registry is the first prospective registry considering paediatric acute kidney replacement therapies (KRTs) in both critical and non-critical care settings, focusing on the three dialysis modalities in Europe. The clinical indications for KRT have expanded; our population was characterized by critically ill patients, primarily boys, who frequently received dialysis in the PICU with CKRT.
Assuntos
Injúria Renal Aguda , Terapia de Substituição Renal , Injúria Renal Aguda/epidemiologia , Injúria Renal Aguda/etiologia , Injúria Renal Aguda/terapia , Criança , Estado Terminal , Feminino , Humanos , Masculino , Morbidade , Sistema de Registros , Diálise Renal , Terapia de Substituição Renal/efeitos adversosRESUMO
FINEAU (2021-2024) is a trans-disciplinary research project involving French, Serbian, Italian, Portuguese and Romanian colleagues, a French agricultural cooperative and two surface-treatment industries, intending to propose chènevotte, a co-product of the hemp industry, as an adsorbent for the removal of pollutants from polycontaminated wastewater. The first objective of FINEAU was to prepare and characterize chènevotte-based materials. In this study, the impact of water washing and treatments (KOH, Na2CO3 and H3PO4) on the composition and structure of chènevotte (also called hemp shives) was evaluated using chemical analysis, X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectroscopy, X-ray computed nanotomography (nano-CT), attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, solid state NMR spectroscopy and thermogravimetric analysis. The results showed that all these techniques are complementary and useful to characterize the structure and morphology of the samples. Before any chemical treatment, the presence of impurities with a compact unfibrillated structure on the surfaces of chènevotte samples was found. Data indicated an increase in the crystallinity index and significant changes in the chemical composition of each sample after treatment as well as in surface morphology and roughness. The most significant changes were observed in alkaline-treated samples, especially those treated with KOH.
Assuntos
Cannabis/química , Produtos Agrícolas/química , Resíduos/análise , Águas Residuárias/química , Poluentes Químicos da Água/isolamento & purificação , Adsorção , Europa (Continente) , Humanos , Cinética , Teste de Materiais , TermogravimetriaRESUMO
This research proposed two pretreatments of viscose fabrics: oxidation with 2,2,6,6-tetramethylpiperidine-1-oxy radical (TEMPO) and coating with TEMPO-oxidized cellulose nanofibrils (TOCN), to introduce functional groups (COOH and CHO) suitable for irreversible binding of chitosan nanoparticles without and with embedded zinc (NCS and NCS + Zn, respectively) and consequently achieving washing durable antibacterial properties of the chitosan nanoparticles functionalized fabrics. The characterizations of pretreated and chitosan nanoparticles functionalized fabrics were performed by FTIR and XPS spectroscopy, elemental analysis, inductively coupled plasma optical emission spectrometry, zeta potential measurements, scanning electron microscopy, determination of COOH and CHO groups content, and antimicrobial activity under dynamic contact conditions. Influence of pretreatments on NCS and NCS + Zn adsorption, chemical, electrokinetic, and antibacterial properties as well as morphology, and washing durability of NCS and NCS + Zn functionalized fabrics were studied and compared. Washing durability was evaluated through changes in the chitosan and zinc content, zeta potential, and antibacterial activity after 1, 3, and 5 washing cycles. Pretreatments improved washing durability of antibacterial properties of chitosan nanoparticles functionalized fabrics. The NCS and NCS + Zn functionalized pretreated fabrics preserved antibacterial activity against S. aureus after five washing cycles, while antibacterial activity against E. coli was preserved only after one washing cycle in the case NCS + Zn functionalized pretreated viscose fabrics.
RESUMO
The surface of cellulose films, obtained from micro nanofibrillated cellulose produced with different enzymatic pretreatment digestion times of refined pulp, was exposed to gas plasma, resulting in a range of surface chemical and morphological changes affecting the mechanical and surface interactional properties. The action of separate and dual exposure to oxygen and nitrogen cold dielectric barrier discharge plasma was studied with respect to the generation of roughness (confocal laser and atomic force microscopy), nanostructural and chemical changes on the cellulose film surface, and their combined effect on wettability. Elemental analysis showed that with longer enzymatic pretreatment time the wetting response was sensitive to the chemical and morphological changes induced by both plasma gases, but distinctly oxygen plasma was seen to induce much greater morphological change while nitrogen plasma contributed more to chemical modification of the film surface. In this novel study, it is shown that exposure to oxygen plasma, subsequently followed by exposure to nitrogen plasma, leads first to an increase in wetting, and second to more hydrophobic behaviour, thus improving, for example, suitability for printing using polar functional inks or providing film barrier properties, respectively.
RESUMO
Lignocellulosic fibers extracted from plants are considered an interesting raw material for environmentally friendly products with multiple applications. This work investigated the feasibility of using hemp- and flax-based materials in the form of felts as biosorbents for the removal of metals present in aqueous solutions. Biosorption of Al, Cd, Co, Cu, Mn, Ni and Zn from a single solution by the two lignocellulosic-based felts was examined using a batch mode. The parameters studied were initial metal concentration, adsorbent dosage, contact time, and pH. In controlled conditions, the results showed that: (i) the flax-based felt had higher biosorption capacities with respect to the metals studied than the hemp-based felt; (ii) the highest removal efficiency was always obtained for Cu ions, and the following order of Cu > Cd > Zn > Ni > Co > Al > Mn was found for both examined biosorbents; (iii) the process was rapid and 10 min were sufficient to attain the equilibrium; (iv) the efficiency improved with the increase of the adsorbent dosage; and (v) the biosorption capacities were independent of pH between 4 and 6. Based on the obtained results, it can be considered that plant-based felts are new, efficient materials for metal removal.
Assuntos
Cannabis/química , Linho/química , Metais Pesados/análise , Metais Pesados/isolamento & purificação , Poluentes Químicos da Água/análise , Poluentes Químicos da Água/isolamento & purificação , Purificação da Água/métodos , Adsorção , Lignina/química , Metais Pesados/metabolismo , Poluentes Químicos da Água/metabolismoRESUMO
The development of automated software and the device for determination of wicking of textile materials, using open-source ImageJ libraries for image processing, and newly designed additional algorithm for the determination of threshold, is presented in this paper. The description of the device, design of the open-source software "Kapilarko", as well as an explanation of the steps: image processing, threshold determination and reading of wicking height, are provided. We have also investigated the possibility of using the artificial neural networks for automatic recognition of the wicking height. The results showed that the recognition of the wet area of the sample, based on the application of artificial neural networks was in a very good agreement with the experimental data. The device's utility for the measurement of wicking ability of textile materials was proved by testing various knitted fabrics. The constructed device has the advantages of providing automated measurement and minimization of the subjective errors of the operators; extremely fast or long-term measurements; digital recording of results; consistency of experimental conditions; possibility of using water instead of colors and, last but not least, low cost of the device. Considering the importance and frequent measurements of wicking ability of textile materials, the advantages of the presented device, as well as the fact that commercial software without publishing the source-code, are used for most of the available devices, we believe that our idea to design the automated software and device by applying the "open-source" approach, will be of benefit to scientists and engineers in using or improving wicking experiments.
Assuntos
Software , TêxteisRESUMO
One of the main objectives of the European health policy framework is to ensure equitable access to high-quality health services across Europe. Here we examined country-specific kidney transplantation and graft failure rates in children and explore their country- and patient-level determinants. Patients under 20 years of age initiating kidney replacement therapy from January 2007 through December 2015 in 37 European countries participating in the ESPN/ERA-EDTA Registry were included in the analyses. Countries were categorized as low-, middle-, and high-income based on gross domestic product. At five years of follow-up, 4326 of 6909 children on kidney replacement therapy received their first kidney transplant. Overall median time from kidney replacement therapy start to first kidney transplantation was 1.4 (inter quartile range 0.3-4.3) years. The five-year kidney transplantation probability was 48.8% (95% confidence interval: 45.9-51.7%) in low-income, 76.3% (72.8-79.5%) in middle-income and 92.3% (91.0-93.4%) in high-income countries and was strongly associated with macro-economic factors. Gross domestic product alone explained 67% of the international variation in transplantation rates. Compared with high-income countries, kidney transplantation was 76% less likely to be performed in low-income and 58% less likely in middle-income countries. Overall five-year graft survival in Europe was 88% and showed little variation across countries. Thus, despite large disparities transplantation access across Europe, graft failure rates were relatively similar. Hence, graft survival in low-risk transplant recipients from lower-income countries seems as good as graft survival among all (low-, medium-, and high-risk) graft recipients from high-income countries.
Assuntos
Falência Renal Crônica , Transplante de Rim , Criança , Ácido Edético , Europa (Continente)/epidemiologia , Sobrevivência de Enxerto , Humanos , Falência Renal Crônica/epidemiologia , Falência Renal Crônica/cirurgia , Transplante de Rim/efeitos adversos , Sistema de RegistrosRESUMO
Bacterial cellulose (BC) hydrogels are among the most efficient materials already being used for the treatment of complex wounds. The moist environment provided by the BC dressing is a key feature assuring efficient wound recovery. Improving the dressings´ moisture-holding ability facilitates its application and leads to an economically preferable extended wear time. To produce materials with reduced moisture loss, BC dressings were impregnated with a secondary hydrophilic component: alginate. The feasibility of an industrial fabrication of this composite was evaluated on pilot scale equipment. It was shown that the procedure can easily be scaled up without significantly increasing the manufacturing time. The resultant composite possessed improved water-retention properties, providing a smooth dressing exchange as demonstrated by a wound-imitating model. The new materials were moreover shown to be compatible with an antimicrobially active compound, which assures their efficiency in the treatment of highly colonized wounds.
Assuntos
Alginatos/química , Antibacterianos/química , Bactérias/química , Bandagens , Celulose/química , Linhagem Celular Transformada , Humanos , Teste de MateriaisRESUMO
Hemp fibers with different amount of hemicelluloses and lignin were subjected to atmospheric pressure dielectric barrier discharge under different conditions (40â¯W and 80â¯W power of discharge, const. time 120â¯s) in order to study influence of plasma treatment on their structure and sorption properties. Wettability of plasma treated samples, compared with precursors, increased due to the changes in hemp fiber surface chemistry confirmed by ATR FTIR spectroscopy and increased roughness as a consequence of intensive surface etching, observed by SEM. After plasma treatment, wettability was the highest for hemp fibers with lower content of hemicelluloses (increase up to 9 times), while wettability of raw hemp fibers and fibers with lower content of lignin increased about 5 and 2 times, respectively. This investigation shows that plasma can be successfully used for improvement of raw hemp fibers wettability, even to substitute the chemical treatment for some applications of hemp.