Silver-loaded poly(vinyl alcohol)/polycaprolactone polymer scaffold as a biocompatible antibacterial system.

A chronic nonhealing wound poses a significant risk for infection and subsequent health complications, potentially endangering the patient's well-being. Therefore, effective wound dressings must meet several crucial criteria, including: (1) eliminating bacterial pathogen growth within the wound, (2) forming a barrier against airborne microbes, (3) promoting cell proliferation, (4) facilitating tissue repair. In this study, we synthesized 8 ± 3 nm Ag NP with maleic acid and incorporated them into an electrospun polycaprolactone (PCL) matrix with 1.6 and 3.4 µm fiber sizes. The Ag NPs were anchored to the matrix via electrospraying water-soluble poly(vinyl) alcohol (PVA), reducing the average sphere size from 750 to 610 nm in the presence of Ag NPs. Increasing the electrospraying time of Ag NP-treated PVA spheres demonstrated a more pronounced antibacterial effect. The resultant silver-based material exhibited 100% inhibition of gram-negative Escherichia coli and gram-positive Staphylococcus aureus growth within 6 h while showing non-cytotoxic effects on the Vero cell line. We mainly discuss the preparation method aspects of the membrane, its antibacterial properties, and cytotoxicity, suggesting that combining these processes holds promise for various medical applications.

Comparative study of photocatalysis with bulk and nanosheet graphitic carbon nitrides enhanced with silver.

The main goal of this research is to investigate the effectiveness of graphitic carbon nitride (g-C3N4, g-CN) in both bulk and nanosheet forms, which have been surface-modified with silver nanoparticles (Ag NPs), as photocatalysts for the degradation of acid orange 7 (AO7), a model dye. The photodegradation of AO7 dye molecules in water was used to test the potential photocatalytic properties of these powder materials under two different lamps with wavelengths of 368 nm (UV light) and 420 nm (VIS light). To produce Ag NPs (Ag content 0.5, 1.5, and 3 wt%) on the g-CN materials, a new synthesis route based on a wet and low-temperature method was proposed, eliminating the need for reducing agents. The photodegradation activity of the samples increased with increasing silver content, with the best photocatalytic performances achieved for bulk g-CN samples and nanosheet silver-modified samples (with the highest content of 3 wt% Ag) under UV light, i.e., more than 75% and 78%, respectively. The VIS-induced photocatalytic activity of both examined series was higher than that of UV. The highest activities of 92% and 98% were achieved for the 1.5% Ag-modified g-CN bulk and nanosheet materials. This research presents an innovative, affordable, and environmentally friendly chemical approach to synthesizing photocatalysts that can be used for degrading organic pollutants in wastewater treatment.

Agronomic Investigation of Spray Dispersion of Metal-Based Nanoparticles on Sunflowers in Real-World Environments.

In environmental and agronomic settings, even minor imbalances can trigger a range of unpredicted responses. Despite the widespread use of metal-based nanoparticles (NPs) and new bio-nanofertilizers, their impact on crop production is absent in the literature. Therefore, our research is focused on the agronomic effect of spray application of gold nanoparticles anchored to SiO2 mesoporous silica (AuSi-NPs), zinc oxide nanoparticles (ZnO-NPs), and iron oxide nanoparticles (Fe3O4-NPs) on sunflowers under real-world environments. Our findings revealed that the biosynthetically prepared AuSi-NPs and ZnO-NPs were highly effective in enhancing sunflower seasonal physiology, e.g., the value of the NDVI index increased from 0.012 to 0.025 after AuSi-NPs application. The distribution of leaf trichomes improved and the grain yield increased from 2.47 t ha-1 to 3.29 t ha-1 after ZnO-NPs application. AuSi-NPs treatment resulted in a higher content of essential linoleic acid (54.37%) when compared to the NPs-free control (51.57%), which had a higher determined oleic acid. No NPs or residual translocated metals were detected in the fully ripe sunflower seeds, except for slightly higher silica content after the AuSi-NPs treatment. Additionally, AuSi-NPs and NPs-free control showed wide insect biodiversity while ZnO-NPs treatment had the lowest value of phosphorus as anti-nutrient. Contradictory but insignificant effect on physiology, yield, and insect biodiversity was observed in Fe3O4-NPs treatment. Therefore, further studies are needed to fully understand the long-term environmental and agricultural sustainability of NPs applications.

Phase Transformation after Heat Treatment of Cr-Ni Stainless Steel Powder for 3D Printing.

Today, Ni-Cr steel is used for advanced applications in the high-temperature and electrical industries, medical equipment, food industry, agriculture and is applied in food and beverage packaging and kitchenware, automotive or mesh. A study of input steel powder from various stages of the recycling process intended for 3D printing was conducted. In addition to the precise evaluation of the morphology, particle size and composition of the powders used for laser 3D printing, special testing and evaluation of the heat-treated powders were carried out. Heat treatment up to 950 °C in an air atmosphere revealed the properties of powders that can appear during laser sintering. The powders in the oxidizing atmosphere change the phase composition and the original FeNiCr stainless steel changes to a two-phase system of Fe3Ni and Cr2O3, as evaluated by X-ray diffraction analysis. Observation of the morphology showed the separation of the oxidic phase in the sense of a brittle shell. The inner part of the powder particle is a porous compact core. The particle size is generally reduced due to the peeling of the oxide shell. This effect can be critical to 3D printing processing, causing defects on the printed parts, as well as reducing the usability of the precursor powder and can also change the properties of the printed part.

Alkali-Treated Alumina and Zirconia Powders Decorated with Hydroxyapatite for Prospective Biomedical Applications.

The alumina and zirconia surfaces were pretreated with chemical etching using alkaline mixtures of ammonia, hydrogen peroxide and sodium hydroxide, and followed with application of the powder layer of Ca-deficient hydroxyapatite (CDH). The influence of etching bath conditions time and concentration on surface development, chemical composition and morphology of medicinal ceramic powders were studied. The following analyses were performed: morphology (scanning electron microscopy), phase composition (X-ray diffraction analysis), changes in binding interactions and chemical composition (FT-Infrared and Energy dispersive spectroscopies). Both types of etchants did not expose the original phase composition changes or newly created phases for both types of ceramics. Subsequent decoration of the surface with hydroxyapatite revealed differences in the morphological appearance of the layer on both ceramic surfaces. The treated zirconia surface accepted CDH as a flowing layer on the surface, while the alumina was decorated with individual CDH aggregates. The goal of this study was to focus further on the ceramic fillers for polymer-ceramic composites used as a biomaterial in dental prosthetics.

Effects of Foliar Application of ZnO Nanoparticles on Lentil Production, Stress Level and Nutritional Seed Quality under Field Conditions.

Nanotechnology offers new opportunities for the development of novel materials and strategies that improve technology and industry. This applies especially to agriculture, and our previous field studies have indicated that zinc oxide nanoparticles provide promising nano-fertilizer dispersion in sustainable agriculture. However, little is known about the precise ZnO-NP effects on legumes. Herein, 1 mg·L-1 ZnO-NP spray was dispersed on lentil plants to establish the direct NP effects on lentil production, seed nutritional quality, and stress response under field conditions. Although ZnO-NP exposure positively affected yield, thousand-seed weight and the number of pods per plant, there was no statistically significant difference in nutrient and anti-nutrient content in treated and untreated plant seeds. In contrast, the lentil water stress level was affected, and the stress response resulted in statistically significant changes in stomatal conductance, crop water stress index, and plant temperature. Foliar application of low ZnO-NP concentrations therefore proved promising in increasing crop production under field conditions, and this confirms ZnO-NP use as a viable strategy for sustainable agriculture.

Biogenic Silver Nanoparticles: What We Know and What Do We Need to Know?

Nanobiotechnology is considered to be one of the fastest emerging fields. It is still a relatively new and exciting area of research with considerable potential for development. Among the inorganic nanomaterials, biogenically synthesized silver nanoparticles (bio-AgNPs) have been frequently used due to their unique physicochemical properties that result not only from their shape and size but also from surface coatings of natural origin. These properties determine antibacterial, antifungal, antiprotozoal, anticancer, anti-inflammatory, and many more activities of bio-AgNPs. This review provides the current state of knowledge on the methods and mechanisms of biogenic synthesis of silver nanoparticles as well as their potential applications in different fields such as medicine, food, agriculture, and industries.

Polyamide 12 Materials Study of Morpho-Structural Changes during Laser Sintering of 3D Printing.

The polyamide (PA)-12 material used for additive manufacturing was studied in aspects of morphology and their structural properties for basic stages received during 3D laser printing. Samples were real, big-scale production powders. The structure of polymer was evaluated from the crystallinity point of view using XRD, FTIR, and DSC methods and from the surface properties using specific surface evaluation and porosity. Scanning electron microscopy was used to observe morphology of the surface and evaluate the particle size and shape via image analysis. Results were confronted with laser diffraction particles size measurement along with an evaluation of the specific surface area. Fresh PA12 powder was found as inhomogeneous in particle size of material with defective particles, relatively high specific surface, high lamellar crystallite size, and low crystallinity. The scrap PA12 crystallinity was about 2% higher than values for fresh PA12 powder. Particles had a very low, below 1 m2/g, specific surface area; particles sintered as twin particles and often in polyhedral shapes.

Colloidal stability of phytosynthesised gold nanoparticles and their catalytic effects for nerve agent degradation.

Herein, Tilia sp. bract leachate was used as the reducing agent for Au nanoparticles (Au NPs) phytosynthesis. The colloidal properties of the prepared Au NPs were determined to confirm their stability over time, and the NPs were then used as active catalysts in soman nerve agent degradation. The Au NPs characterisation, reproducibility and stability studies were performed under transmission electron microscopy, ultraviolet visible spectroscopy and with ζ-potential measurements. The reaction kinetics was detected by gas chromatography coupled with mass spectrometry detector and solid-phase micro-extraction to confirm the Au NPs applicability in soman hydrolysis. The 'green' phytosynthetic formation of colloidal crystalline Au NPs with dominant quasi-spherical shape and 55 ± 10 nm diameter was successfully achieved, and there were no significant differences in morphology, ζ-potential or absorbance values observed during the 5-week period. This verified the prepared colloids' long-term stability. The soman nerve agent was degraded to non-toxic substances within 24 h, with 0.2156 h-1 reaction rate constant. These results confirmed bio-nanotechnology's great potential in preparation of stable and functional nanocatalysts for degradation of hazardous substances, including chemical warfare agents.

Aspergillus niger Decreases Bioavailability of Arsenic(V) via Biotransformation of Manganese Oxide into Biogenic Oxalate Minerals.

The aim of this work was to evaluate the transformation of manganese oxide (hausmannite) by microscopic filamentous fungus Aspergillus niger and the effects of the transformation on mobility and bioavailability of arsenic. Our results showed that the A. niger strain CBS 140837 greatly affected the stability of hausmannite and induced its transformation into biogenic crystals of manganese oxalates-falottaite and lindbergite. The transformation was enabled by fungal acidolysis of hausmannite and subsequent release of manganese ions into the culture medium. While almost 45% of manganese was bioextracted, the arsenic content in manganese precipitates increased throughout the 25-day static cultivation of fungus. This significantly decreased the bioavailability of arsenic for the fungus. These results highlight the unique A. niger strain's ability to act as an active geochemical factor via its ability to acidify its environment and to induce formation of biogenic minerals. This affects not only the manganese speciation, but also bioaccumulation of potentially toxic metals and metalloids associated with manganese oxides, including arsenic.

Foliar Application of Low Concentrations of Titanium Dioxide and Zinc Oxide Nanoparticles to the Common Sunflower under Field Conditions.

Nano-fertilisers have only recently been introduced to intensify plant production, and there still remains inadequate scientific knowledge on their plant-related effects. This paper therefore compares the effects of two nano-fertilisers on common sunflower production under field conditions. The benefits arising from the foliar application of micronutrient-based zinc oxide fertiliser were compared with those from the titanium dioxide plant-growth enhancer. Both the zinc oxide (ZnO) and titanium dioxide (TiO2) were delivered by foliar application in nano-size at a concentration of 2.6 mg·L-1. The foliar-applied nanoparticles (NPs) had good crystallinity and a mean size distribution under 30 nm. There were significant differences between these two experimental treatments in the leaf surfaces' trichomes diversity, ratio, width, and length at the flower-bud development stage. Somewhat surprisingly, our results established that the ZnO-NPs treatment induced generally better sunflower physiological responses, while the TiO2-NPs primarily affected quantitative and nutritional parameters such as oil content and changed sunflower physiology to early maturation. There were no differences detected in titanium or zinc translocation or accumulation in the fully ripe sunflower seeds compared to the experimental controls, and our positive results therefore encourage further nano-fertiliser research.

Effect of Foliar Spray Application of Zinc Oxide Nanoparticles on Quantitative, Nutritional, and Physiological Parameters of Foxtail Millet (Setaria italica L.) under Field Conditions.

It has been shown that the foliar application of inorganic nano-materials on cereal plants during their growth cycle enhances the rate of plant productivity by providing a micro-nutrient source. We therefore studied the effects of foliarly applied ZnO nanoparticles (ZnO NPs) on Setaria italica L. foxtail millet's quantitative, nutritional, and physiological parameters. Scanning electron microscopy showed that the ZnO NPs have an average particle size under 20 nm and dominant spherically shaped morphology. Energy dispersive X-ray spectrometry then confirmed ZnO NP homogeneity, and X-ray diffraction verified their high crystalline and wurtzite-structure symmetry. Although plant height, thousand grain weight, and grain yield quantitative parameters did not differ statistically between ZnO NP-treated and untreated plants, the ZnO NP-treated plant grains had significantly higher oil and total nitrogen contents and significantly lower crop water stress index (CWSI). This highlights that the slow-releasing nano-fertilizer improves plant physiological properties and various grain nutritional parameters, and its application is therefore especially beneficial for progressive nanomaterial-based industries.

Ag-AgCl Nanoparticles Fixation on Electrospun PVA Fibres: Technological Concept and Progress.

Polymer-metal based material with unique 3D structure is an attractive substrate for the development of biomedical applications. A novel preparation of the composite from polymer fibres and silver nanoparticles has been designed through: (1) preparation of silver nanoparticles by phytosynthesis and (2) incorporation of these nanoparticles in a fibrous membrane prepared by electrospinning. The nanoparticle biosynthesis was performed in a pure environmental-friendly, easy, static, bottom-up in vitro regime using Tilia sp. leachate. TEM and XRD depict the formation, stabilisation and encapsulation of crystalline silver (14 ± 9 nm) nanoparticles (NPs) in one simple step with low tendency to aggregate. We achieved successful incorporation in the uniform electrospun 221 ± 24 nm poly(vinylalcohol) fibres, and this confirms the possibility of its use in the biomedical field. Both SEM with EDX and TEM analysis determined fibre uniformity with the presence of silver NPs, and ICP-AES confirmed the relatively similar metal concentration throughout the triplicate measurement of fibre structures on the 2 × 2 cm area in the following manner: 0.303 ± 0.018 wt. %, 0.282 ± 0.017 wt. %, and 0.281 ± 0.017 wt. %. Our hypothesis is based on previously verified preparation of active silver NPs and the easily prepared PVA electrospun fibres which act as a water soluble matrix. The simple methodology of incorporating biosynthetically prepared NPs in the PVA fibers highlights the effectiveness of this material, with simple release from water-soluble PVA and final activation of the prepared NPs.

Phytosynthesis of Ag, ZnO and ZrO2 Nanoparticles Using Linden: Changes in Their Physical-Chemical Nature Over Time.

Bionanotechnology provides many new methods and protocols in nanomaterial preparation. One of these special new chemical methods is phytosynthesis. The application of biological processes in living organisms such as bacteria, fungi and higher plants contributes to rapid and easy formation of metallic nanoparticles. These nanoparticles present a promising future in heterogeneous catalysis and medicine, and here we focus on phytosynthesis of Ag, ZnO and ZrO2 nanoparticles using leachate from the linden plant. Nanoparticle activity in liquid is an important aspect of their behavior, and we investigated nanoparticles ζ-potential and monitored their particle size by dynamic light scattering during the period of three months. Transmission electron microscopy then determined shape and morphology, with results confirming their spherical shape and average size in tens and hundreds of nanometers. The amount of metals was estimated in tens of mg L-1 and the different nanoparticle sizes obtained by dynamic light scattering and transmission electron microscopy are discussed. The nanoparticles were tested against 4 human pathogens using minimum inhibitory concentration to investigate their antimicrobial potential. Only Ag nanoparticles provided antibacterial properties against Escherichia coli and Pseudomonas aeruginosa; with the remaining nanoparticles having no antibacterial effect on the four tested pathogens. All studied phenomena are related to nanoparticle concentration and their surface charge, and therefore ζ-potential and other physical and chemical properties are important in ascertaining positive and negative aspects of metallic nanoparticles in future applications and related research.

From biotechnology principles to functional and low-cost metallic bionanocatalysts.

Chemical, physical and mechanical methods of nanomaterial preparation are still regarded as mainstream methods, and the scientific community continues to search for new ways of nanomaterial preparation. The major objective of this review is to highlight the advantages of using green chemistry and bionanotechnology in the preparation of functional low-cost catalysts. Bionanotechnology employs biological principles and processes connected with bio-phase participation in both design and development of nano-structures and nano-materials, and the biosynthesis of metallic nanoparticles is becoming even more popular due to; (i) economic and ecologic effectiveness, (ii) simple one-step nanoparticle formation, stabilisation and biomass support and (iii) the possibility of bio-waste valorisation. Although it is quite difficult to determine the precise mechanisms in particular biosynthesis and research is performed with some risk in all trial and error experiments, there is also the incentive of understanding the exact mechanisms involved. This enables further optimisation of bionanoparticle preparation and increases their application potential. Moreover, it is very important in bionanotechnological procedures to ensure repeatability of the methods related to the recognised reaction mechanisms. This review, therefore, summarises the current state of nanoparticle biosynthesis. It then demonstrates the application of biosynthesised metallic nanoparticles in heterogeneous catalysis by identifying the many examples where bionanocatalysts have been successfully applied in model reactions. These describe the degradation of organic dyes, the reduction of aromatic nitro compounds, dehalogenation of chlorinated aromatic compounds, reduction of Cr(VI) and the synthesis of important commercial chemicals. To ensure sustainability, it is important to focus on nanomaterials that are capable of maintaining the important green chemistry principles directly from design inception to ultimate application.

Phytosynthesis of Au and Au/ZrO2 bi-Phasic System Nanoparticles with Evaluation of Their Colloidal Stability.

Due to its easy availability, preparation, handling and non-toxic nature, Equisetum arvense horsetail extract was chosen as a reducing, stabilizing and functionalizing agent for Au and bi-phasic Au/ZrO2 nanoparticle phytosynthesis-inorganic nanoparticle synthesis mediated by plant extract. We studied Au and bi-phasic Au/ZrO2 nanoparticles in colloids by various physical-chemical and analytical methods over 5 weeks. Dynamic Light Scattering and Scanning Transmission Electron Microscopy compared core and hydrodynamic diameters of nanoparticles. ζ-potential measurement indirectly determined nanoparticles stability in liquid medium. Ultraviolet-Visible Spectroscopy characterized basic absorbance maxima for both Au and the bi-phasic Au/ZrO2 system. Finally, total metal concentration was determined using Inductively Coupled Plasma Mass Spectrometry. ζ-potential measurements proved satisfactory stability of both Au (-13.4 to -17 mV) and Au/ZrO2 nanoparticles (-14.1 to -17.5 mV) over the experimental period. Scanning Transmission Electron Microscopy with Selected Area Diffraction analysis confirmed nanoparticles crystalline nature, and we determined 24 nm and 40 nm core nanogold diameters in Au and Au/ZrO2 nanoparticle colloids. Dynamic light scattering analysis confirmed the dichotomy between particle sizes in liquid medium in the hundreds of nanometers measured, and long-term measurements confirmed reasonable colloid stability-a paramount parameter for potential nanoparticles applications; especially in heterogeneous catalysis.

Silver/Chitosan Antimicrobial Nanocomposites Coating for Medical Devices: Comparison of Nanofiller Effect Prepared via Chemical Reduction and Biosynthesis.

Medical devices have an essential part in healthcare system in recent years, such as usage of heart valves, several types of stents and implants devices in patients. However, bacterial infection of medical devices causes critical issues for patients due to attachment of bacteria and formation of biofilm onto the medical devices. Therefore, finding an effective antibacterial coating to prevent biofilm formation and infection is our goal. In this study, we developed silver/chitosan nanocomposites for antimicrobial coating system by chemical and green methods using sodium borohydride and linden extract, respectively. Silver is known as a strong inorganic antimicrobial agent to kill bacteria by inactivating enzymes and dysfunction bacterial cell membranes. By immobilizing silver nanoparticles on chitosan biopolymer can prevent agglomeration of nanoparticles, besides it can improve the biocompatibility. We characterized properties of our silver chitosan nanocomposites samples using particle size distribution, ultraviolet-visible spectroscopy, X-ray diffraction analysis and scanning electron microscopy. Effective antimicrobial film preventing biofilm formation on medical devices was designed. Antimicrobial testing confirmed antimicrobial properties however variable for each type of nanosilver.

Nanogold Biosynthesis Mediated by Mixed Flower Pollen Grains.

Physical and chemical methods for nanoparticle synthesis are disadvantageous to less energy demanding and more efficient and environmentally friendly biological approaches. Thus, in this paper, we designed simple, bottom-up, in vitro, static experiment under laboratory conditions using suspension of mixed flower pollen grains for nanoparticle synthesis. Pollen grains provided template substrates for gold nanoparticles synthesis from dissolved Au(III). Transmission and scanning electron microscopy along with ultraviolet-visible spectra confirmed the gold nanoparticles formation. The biosynthesized/phytosynthesized gold nanoparticles had relative narrow size distribution (from 3 to 11 nm) with dominant spherical morphology with no aggregated forms. Thus, the gold nanoparticles in pollen dispersion provides excellent stability and dispersity.

Increased Colloidal Stability and Decreased Solubility-Sol-Gel Synthesis of Zinc Oxide Nanoparticles with Humic Acids.

Adding the humic acid coating to the nanoparticles of zinc oxide (ZnO-NP) may improve the properties necessary for their colloidal stability. To show how humic acid coating affects the properties of ZnO-NP, three differently sol-gel synthesized ZnO-NP were synthesized: pristine zinc oxide nanoparticles without coating (p-ZnO-NP) and humic acid coated zinc oxide nanoparticles at two different initial concentrations of 20 mg/L (HA20-ZnO-NP) and 200 mg/L (HA200-ZnO-NP) of humic acids in the starting solution. All ZnO-NP were found to be nanocrystals of mineral zincite exhibiting wurtzite crystal symmetry. Transmission electron microscopy showed that capping by humic acids during synthesis decreased the size of HA20-ZnO-NP and HA200-ZnO-NP compared to p-ZnO-NP nanoparticles. Via experiments, HA20-ZnO-NP were found to dissolve less and have a similar or higher stability than both p-ZnO-NP and HA200-ZnO-NP.

Fungi as an efficient mycosystem for the synthesis of metal nanoparticles: progress and key aspects of research.

Nanotechnology is an emerging cutting-edge technology, which involves interdisciplinary subjects, such as physics, chemistry, biology, material science and medicine. Different methods for the synthesis of nanoparticles have been discussed here. Although physical and chemical methods have been successfully used to synthesize nanoparticles, the use of hazardous chemicals and synthesis at high temperature is a matter of concern. Hence, there is a necessity to develop eco-friendly techniques for the synthesis of nanoparticles. Biosynthesis of nanoparticles by fungi, bacteria, actinomycetes, lichen and viruses have been reported eco-friendly. Moreover, the fungal system has emerged as an efficient system for nanoparticle synthesis as fungi possess distinctive characters including high wall binding capacity, easy to culture and simpler biomass handling, etc. In this review, we have discussed fungi as an important tool for the fabrication of nanoparticles. In addition, methods and mechanism for synthesis of nanoparticles and its potential applications have also been discussed.