A Coaxial RF Applicator for Ultra-High Field Human MRI.

OBJECTIVE: To develop a novel radio-frequency (RF) concept for ultra-high field (UHF) human magnetic resonance imaging (MRI) based on a coaxial resonant cavity. METHODS: A two-channel slotted coaxial cavity RF applicator was designed for human head MRI at 9.4T. Physical dimensions made the proposed conducting structure resonant at the required frequency without tuning lumped elements. Numerical electromagnetic modeling was used to optimize the design. RF safety was assessed with two representative human body models. MR experiments on a 9.4T scanner included gradient echo images and mapping of a circularly polarized RF magnetic field in the human head phantom. RESULTS: The simulations and the phantom MR experiments agreed both qualitatively and quantitatively. The design was relatively simple, robust and required only a few additional reactive elements for the applicator's input impedance matching. The transmit efficiency and homogeneity of the excitation field were only 20% and 4% lower compared to a conventional 8-channel head array. CONCLUSION: The coaxial RF applicator was feasible for human MRI at UHF and required no lumped elements for its tuning. Imaging performance of the RF applicator was only moderately lower compared to the conventional transmit array, but would be sufficient to provide an anatomical reference for the heteronuclei MRI. SIGNIFICANCE: An alternative approach with the minimal involvement of lumped elements becomes feasible to design volume-type RF coils for UHF human MRI.

Online self-test identifies women at high familial breast cancer risk in population-based breast cancer screening without inducing anxiety or distress.

INTRODUCTION: Identifying high familial breast cancer (FBC) risk improves detection of yet unknown BRCA1/2-mutation carriers, for whom BC risk is both highly likely and potentially preventable. We assessed whether a new online self-test could identify women at high FBC risk in population-based BC screening without inducing anxiety or distress. METHODS: After their visit for screening mammography, women were invited by email to take an online self-test for identifying highly increased FBC risk-based on Dutch guidelines. Exclusion criteria were previously diagnosed as increased FBC risk or a personal history of BC. Anxiety (State-Trait Anxiety Inventory Dutch Version), distress (Hospital Anxiety Depression Scale) and BC risk perception were assessed using questionnaires, which were completed immediately before and after taking the online self-test and 2 weeks later. RESULTS: Of the 562 women invited by email, 406 (72%) completed the online self-test while 304 also completed questionnaires (response rate 54%). After exclusion criteria, 287 (51%) were included for data analysis. Median age was 56 years (range 50-74). A high or moderate FBC risk was identified in 12 (4%) and three (1%) women, respectively. After completion of the online self-test, anxiety and BC risk perception were decreased while distress scores remained unchanged. Levels were below clinical relevance. Most women (85%) would recommend the self-test; few (3%) would not. CONCLUSION: The online self-test identified previously unknown women at high FBC risk (4%), who may carry a BRCA1/2-mutation, without inducing anxiety or distress. We therefore recommend offering this self-test to women who attend population-based screening mammography for the first time.

2D radially compensating excitation pulse in combination with an internal transceiver antenna for 3D MRI of the rectum at 7 T.

PURPOSE: The high precession frequency in ultrahigh field MRI coincides with reduced RF penetration, increased RF power deposition and consequently can lead to reduced scan efficiency. However, the shorter wavelength enables the use of efficient antennas rather than loop coils. In fact, ultrathin monopole antennas have been demonstrated at 7 T, which fit in natural cavities like the rectum in the human body. As the RF field generated by the antenna provides an extremely nonuniform B1 field, the use of conventional RF pulses will lead to severe image distortions and highly nonuniform contrast. However, using the two predominant dimensions (orthogonal to the antenna), 2D RF pulses can be designed that counteract the nonuniform B1 into uniform flip angles. In this study the authors investigate the use of an ultrathin antenna not only for reception, but also for transmission in 7 T MRI of the rectum. METHODS: The 2D radially compensating excitation (2D RACE) pulse was designed in matlab. SAR calculations between the 2D RACE pulse and an adiabatic RF pulse (BIR-4) have been obtained, to visualize the gain in decreasing the SAR when using the 2D RACE pulse instead of an adiabatic RF pulse. The authors used the 7 T whole body MR system in combination with an internally placed monopole antenna used for transceiving and obtained 3D gradient echo images with a conventional sinc pulse and with the 2D RACE pulse. For extra clarity, they also reconstructed an image where the receive field of the antenna was removed. RESULTS: Comparing the results of the SAR simulations of the 2D RACE pulse with a BIR-4 pulse shows that for low flip angles (θ < 41°) the SAR can be decreased with a factor of 4.8 or even more, when using the 2D RACE pulse. Relative to a conventional sinc excitation, the 2D RACE pulse achieves more uniform flip angle distributions than a BIR-4 pulse with a smaller SAR increase (16 × versus 64 ×). CONCLUSIONS: The authors have shown that the 2D RACE pulse provides more homogeneous flip angles for gradient echo sequences when compared to a conventional sinc pulse albeit at increased SAR. However, when compared to adiabatic RF pulses, as shown by simulations, the SAR of the 2D RACE pulse can be an order of magnitude less. Phantom and in vivo human rectum images are obtained to demonstrate that the 2D RACE pulse can provide a uniform excitation while transmitting with a single ultrathin endorectal antenna at 7 T. The combination of thin rectal antennas with efficient uniform transmit can open up new possibilities in high resolution imaging of rectal cancer.

Improved steering of the RF field of traveling wave MR with a multimode, coaxial waveguide.

PURPOSE: Magnetic resonance imaging of humans at high magnetic field strengths is strongly influenced by the interference of the radiofrequency (RF) electromagnetic field and the body. To minimize this effect, multiple RF sources could be used. A novel setup (called multimode, coaxial waveguide) is proposed that facilitates RF shimming based on the traveling waves. METHODS: The multimode, coaxial waveguide combines the coaxial waveguide, cylindrical waveguide, high dielectric permittivity lining, and eight radial stub antennas. Each antenna excites multiple waveguide modes. Based on modes orthogonality, a method was devised to decompose an excitation pattern of single stub antenna into waveguide modes. RESULTS: The number of modes present in the excitation pattern of a single stub antenna increased with the higher effective permittivity of the dielectric lining. Thus, RF shimming performance of the setup was improved. An average homogeneity of 10% was demonstrated for a single slice of each principle plane in the human head at 7 T. CONCLUSION: Traveling wave RF shimming is feasible both in axial and longitudinal directions and is improved with an increased amount of orthogonal waveguide modes. Nevertheless, with the currently available RF amplifiers at 7 T, the performance of the setup is limited to low flip angles.

Calculation of SAR and temperature rise in a high-resolution vascularized model of the human eye and orbit when exposed to a dipole antenna at 900, 1500 and 1800 MHz.

The eye is considered to be a critical organ when determining safety standards for radiofrequency radiation. With a detailed anatomy of the human eye and orbit inserted in a whole-head model, the specific absorption rates (SARs) and thermal effects were determined under exposure to a dipole antenna representing a mobile phone operating at 900, 1500 and 1800 MHz with an output power of 1 W. The temperature rise was calculated by taking the blood flow into account either by the Pennes bioheat model or by including the discrete vasculature (DIVA). In addition, a simple spherical model using constant heat transfer coefficients was used. Peak SARs in the humour are 4.5, 7.7 and 8.4 W kg(-1) for 900, 1500 and 1800 MHz respectively. Averaged over the whole eyeball, the SARs are 1.7, 2.5 and 2.2 W kg(-1). The maximum temperature rises in the eye due to the exposure are 0.22, 0.27 and 0.25 degrees C for exposure of 900, 1500 and 1800 MHz, respectively, calculated with DIVA. For the Pennes bioheat model, the temperature rises are slightly lower: 0.19, 0.24, 0.22 degrees C respectively. For the simple spherical model, the maximum temperature rises are 0.15, 0.22 and 0.20 degrees C. The peak temperature is located in the anterior part of the lens for 900 MHz and deeper in the eye for higher frequencies, and in the posterior part of the lens for 1500 MHz and close to the centre of the eyeball for 1800 MHz. For these RF safety applications, both DIVA and the Pennes bioheat model could be used to relate the SAR distributions to the resulting temperature distributions. Even though, for these artificial exposure conditions, the SAR values are not in compliance with safety guidelines, the maximum temperature rises in the eye are too small to give harmful effects. The temperature in the eye also remains below body core temperature.

Comparison of intra-luminal versus intra-tumoural temperature measurements in patients with locally advanced prostate cancer treated with the coaxial TEM system: report of a feasibility study.

A study was performed on regional hyperthermia for patients with locally advanced prostate carcinoma. The primary objective was to analyse the thermometry data with an emphasis on the possibility of replacing invasive thermometry by tumour-related intra-luminal thermometry. Fourteen patients were treated with a combination of conformal external beam radiotherapy (70 Gy) and hyperthermia. Hyperthermia was delivered using the Coaxial TEM system, one treatment per week, to a total of five treatments. Thermometry was performed in bladder, urethra, rectum and esophagus. Invasive thermometry in the prostate was carried out during one or two treatments for each patient by placing transperineally a central and a peripheral catheter. Heterogeneous temperature distributions were measured in the prostate. The mean average invasive temperature range was 1.1 degrees C. Due to the temperature heterogeneity and a limited number of thermometry sensors (mean 7, range 2-13), large variability between treatments and patients existed regarding achieved temperatures and dose. The mean invasive T90 was 40.2 +/- 0.6 degrees C and T50 was 40.8 +/- 0.6 degrees C. The mean Cum min T90>40.5 degrees C per treatment was 22 (range 0-50). Importantly, intra-luminal temperatures did not reliably predict invasively measured temperatures. Invasive thermometry, therefore, remains compulsory to calculate a thermal dose for an individual patient. Changes in temperature during treatment, measured by the urethral sensors, corresponded well with changes in temperature measured by the individual invasive sensors. Similar comparison of rectal temperature changes with intra-prostatic temperature changes was not as predictive. The similarity in temperature changes between the urethral and interstial sites, suggests that urethral temperatures are sufficient for treatment optimization. The SAR profile did not correspond with the temperature profile indicating heterogeneous perfusion. Although regional hyperthermia in combination with external beam radiotherapy for locally advanced prostate carcinoma is clinically feasible, the question on the importance of invasive thermometry remains.

Treatment planning for capacitive regional hyperthermia.

Capacitively coupled hyperthermia devices are widely in use, mainly in Asian countries. In this paper, a comprehensive treatment planning system, including a Specific Absorption Rate (SAR) and thermal model for capacitively coupled hyperthermia, is described and demonstrated using a heterogeneous patient model. In order to accurately model a hyperthermia treatment, simulation at high resolution is mandatory. Using the quasi-static approximation, the electromagnetic problem can be solved at high resolution with acceptable computational effort. The validity of the quasi-static approximation is demonstrated by comparing the Maxwell solution of a phantom problem to the quasi-static approximation. Modelling of capacitive hyperthermia of the prostate reveals the difficulty of heating deep-seated tumours in the pelvic area. Comparison of the SAR distribution in the heterogeneous patient model and a patient shaped agar phantom shows a shielding effect of the pelvic bone and the influence of the fat-muscle distribution. It is shown that evaluation of capacitive hyperthermia with agar phantoms leads to overly optimistic conclusions. Therapeutic relevant tumour temperatures can only be obtained by permitting temperature extrema in normal tissue. This concurs with clinical practice, where treatment-limiting hot spots restrict the tumour temperature. It is demonstrated that the use of very cold overlay bolus bags has only a very superficial effect. The presented model can be used for individual treatment planning and optimization, for the evaluation of capacitive applicator modifications and comparison with other devices.

Improvement of absorbing structures used in regional hyperthermia.

Local pain is a major limiting factor in regional hyperthermia treatment with radiative applicators. Absorbing structures, consisting of agar bound saline water, have been used successfully to reduce peripheral hot spots. However, both clinical experience and simulation results indicate a SAR elevation in the tissue under the edges of the absorber block. This paper investigates the effect of modification of shape, position and spatial composition of the absorber blocks on the central attenuating effect and the SAR elevating effect at the edges. A selection from a set of five options is made based on simulations with a phantom and a single ring dipole applicator. The simulations have been performed with the FDTD core of the regional hyperthermia treatment planning system. It is shown that tapering of the absorber edge and introduction of a water layer between the absorber and the skin can reduce the edge effect in the superficial fat layer by approximately 50% with respect to a rectangular absorber. A further reduction of 15% can be obtained by an absorber with an appropriate gradient of its conductivity in the direction of the dominant E-field. The modified absorbers produce a central attenuating effect comparable to the rectangular type. The use of a water layer type and a sigma gradient type absorber is also analysed in a patient anatomy, both in the dipole ring applicator, operating at 70 MHz, as well as in a three ring Cavity Slot (CS) applicator, operating at 150 MHz. The mutual influence of phase-amplitude steering and the application of absorbers is investigated in the CS applicator. It appears that absorbers have a significant influence on the interference pattern in the patient model, possibly causing substantial reduction of the SAR value in the tumour and limiting the possibility of ad hoc application of absorbers. Re-optimization can only partly cancel this effect. Local SAR reduction by phase-amplitude control alone can match or improve the effect obtained with modified absorbers.

CT-resolution regional hyperthermia treatment planning.

Recent development of quasistatic zooming has enabled the computation of mm-resolution SAR distributions within reasonable computation times. These high-resolution SAR distributions proved to be completely dissimilar from the cm-resolution distributions. To study the impact of high-resolution SAR modelling on regional hyperthermia treatment planning (HTP), a conventional, low-resolution treatment plan is compared to an high-resolution plan. This comparison shows that the high-resolution plan yields totally different SAR and temperature distributions when compared to the conventional plan. Both SAR and temperature maxima predicted by the low-resolution plan are not predicted by the high-resolution plan and, even worse, the low-resolution plan fails to predict maxima that are predicted by the high-resolution plan. Furthermore, it appears that small-scale SAR maxima can result in temperature maxima which may cause treatment-limiting hot spots. These small-scale SAR maxima appear to be highly determined by the dielectric geometry of the patient. This demonstrates the need for an accurate, high-resolution description of this dielectric geometry. Moreover, it suggests that it may be very difficult to reduce potential treatment-limiting hot spots in clinical practice. This study demonstrates the need for high-resolution regional hyperthermia treatment planning.

Regional hyperthermia applicator design using FDTD modelling.

Recently published results confirm the positive effect of regional hyperthermia combined with external radiotherapy on pelvic tumours. Several studies have been published on the improvement of RF annular array applicator systems with dipoles and a closed water bolus. This study investigates the performance of a next-generation applicator system for regional hyperthermia with a multi-ring annular array of antennas and an open water bolus. A cavity slot antenna is introduced to enhance the directivity and reduce mutual coupling between the antennas. Several design parameters, i.e. dimensions, number of antennas and operating frequency, have been evaluated using several patient models. Performance indices have been defined to evaluate the effect of parameter variation on the specific absorption rate (SAR) distribution. The performance of the new applicator type is compared with the Coaxial TEM. Operating frequency appears to be the main parameter with a positive influence on the performance. A SAR increase in tumour of 1.7 relative to the Coaxial TEM system can be obtained with a three-ring, six-antenna per ring cavity slot applicator operating at 150 MHz.

Quasistatic zooming of FDTD E-field computations: the impact of down-scaling techniques.

Due to current computer limitations, regional hyperthermia treatment planning (HTP) is practically limited to a resolution of 1 cm, whereas a millimetre resolution is desired. Using the centimetre resolution E-field distribution, computed with, for example, the finite-difference time-domain (FDTD) method and the millimetre resolution patient anatomy it is possible to obtain a millimetre resolution SAR distribution in a volume of interest (VOI) by means of quasistatic zooming. To compute the required low-resolution E-field distribution, a low-resolution dielectric geometry is needed which is constructed by down-scaling the millimetre resolution dielectric geometry. In this study we have investigated which down-scaling technique results in a dielectric geometry that yields the best low-resolution E-field distribution as input for quasistatic zooming. A segmented 2 mm resolution CT data set of a patient has been down-scaled to 1 cm resolution using three different techniques: 'winner-takes-all', 'volumetric averaging' and 'anisotropic volumetric averaging'. The E-field distributions computed for those low-resolution dielectric geometries have been used as input for quasistatic zooming. The resulting zoomed-resolution SAR distributions were compared with a reference: the 2 mm resolution SAR distribution computed with the FDTD method. The E-field distribution for both a simple phantom and the complex partial patient geometry down-scaled using 'anisotropic volumetric averaging' resulted in zoomed-resolution SAR distributions that best approximate the corresponding high-resolution SAR distribution (correlation 97, 96% and absolute averaged difference 6, 14% respectively).

The use of absorbing structures during regional hyperthermia treatment.

Local pain is the main factor that limits regional hyperthermia treatment. Using the SAR model of the regional hyperthermia treatment planning system, the capability of absorbing blocks to reduce peripheral hot spots was investigated. The effect of rectangular absorbers of various size and salinity on an elliptical phantom in the Coaxial TEM was evaluated. The computed results were compared with SAR values measured in the phantom. Absorbers of 9 x 9 x 4 cm3 and a salinity of 18 gram l(-1) provide a SAR reduction in the muscle equivalent material, centrally under the absorber of at least 50% at a depth of up to 3 cm. The effect on the central (i.e. tumour) region is less than 20%. Larger absorbers have a more global effect and cause more attenuation in the central region. The attenuating effect depends strongly on the thickness of the fat layer between muscle and absorber. More than 2 cm fat limits the effective use of absorbers. Absorbers can induce a significant increase of SAR in muscle and fat near their edges. This effect also depends on absorber size and salinity and the thickness of the fat layer. The effect of an absorber was also evaluated with a patient anatomy, yielding results in agreement with the phantom experiments.

Development of a regional hyperthermia treatment planning system.

A flexible and fast regional hyperthermia treatment planning system for the Coaxial TEM System has been devised and is presented. Using Hounsfield Unit based thresholding and manually outlining of the tumour, a 40 cm CT data set (slice thickness 5 mm) is segmented and down scaled to a resolution of 1 cm, requiring only 30 min. The SAR model is based on the finite-difference time-domain (FDTD) method. The number of time steps to achieve numerical stability has been determined and was found to be 7000. Various optimizations of the SAR model have been applied, resulting in a relatively short computation time of 3.7 h (memory requirements 121 MB) on a Pentium III, 450 MHz standard personal computer, running GNU/Linux. The model has been validated using absolute value(Ez) measurements in a standard phantom inserted in the Coaxial TEM Applicator under different conditions and a good agreement was found. Hyperthermia treatment planning in combination with the homemade visualization tools have provided much insight in the regional hyperthermia treatment with the Coaxial TEM Applicator.

Quasistatic zooming for regional hyperthermia treatment planning.

Due to current computer limitations, specific absorption rate (SAR) distributions in regional hyperthermia treatment planning (HTP) are limited to centimetre resolution. However, since patient anatomy is highly structured on a millimetre scale, millimetre-resolution SAR modelling is required. A method called quasistatic zooming has been developed to obtain a high-resolution SAR distribution within a volume of interest (VOI): using the low-resolution E-field distribution and the high-resolution patient anatomy, the high-resolution SAR distribution is computed within a small zoom volume Q (small compared with the wavelength in water (lambda(w))). Repeating this procedure yields the zoomed-resolution SAR distribution in an arbitrary VOI. To validate this method for a VOI that is not small compared with lambda(w), high-resolution finite-difference time-domain (FDTD) modelling is needed. Since this is impractical for a clinical applicator, a computer model of a small applicator has been created. A partial patient anatomy is inserted into the applicator and both high- and low-resolution SAR distributions are computed for this geometry. For the same geometry, zoomed-resolution SAR distributions are computed with different sizes of Q. To compare the low- and zoomed-resolution SAR distributions with the high-resolution one, the correlation and averaged absolute difference are computed. These numbers are improved considerably using zooming (correlation 58% to 92%; averaged absolute difference 43% to 20%). These results appear to be independent of the size of Q, up to 0.3 lambda(w). Quasistatic zooming is a valuable tool in high-resolution regional HTP.

High-resolution SAR modelling for regional hyperthermia: testing quasistatic zooming at 10 MHz.

Present-day regional hyperthermia treatment planning systems are limited to centimetre resolution. To obtain CT-resolution SAR distributions, a method called quasistatic zooming has been developed: using the centimetre-resolution E-field distribution and the CT-resolution tomogram, the CT-resolution SAR distribution is obtained. For a low frequency of 10 MHz this method has been validated sucessfully using CT-resolution SAR computations. It appears that these CT-resolution SAR distributions are completely different from centimetre-resolution SAR distributions, indicating the necessity for high-resolution SAR modelling. Using the presented zooming technique, reliable CT-resolution SAR modelling is now possible with relatively short computation times. So far, the zooming method has only been validated for low frequencies, but clinically relevant frequencies appear to be possible.

Prevalence and need for replacement of amalgam and composite restorations in Dutch adults.

In 1986, the first nationwide epidemiological survey of adult oral health and attitudes to oral health care was carried out in The Netherlands. One of the aims of this study was to evaluate the prevalence and the quality (in terms of need for replacement) of amalgam and composite restorations in the Dutch adult population. A group of 600 dentate individuals, 20-44 years of age, was examined. Stratified cluster sampling included as factors age, gender, socio-economic status, and area of residence. Two additional parameters were studied: frequency of visiting a dentist and type of health insurance. Oral examinations consisted of direct (mirror and explorer) and indirect (color slides and bite-wing radiographs) observations with use of well-defined criteria. On average, 13.4 restorations per individual were present, of which 23.3% were classified as unsatisfactory. A great difference in prevalence and quality data was found among several types of restorations. Test results (ANOVA) for effects of age, gender, socio-economic status, area of residence, frequency of visiting a dentist, and insurance on the prevalence of (un)satisfactory restorations resulted nearly always in significant effects of only age and frequency of visits to a dentist. There was a tendency (p less than 0.05) for the prevalence of (un)satisfactory restorations to be higher with increasing age.(ABSTRACT TRUNCATED AT 250 WORDS)