Magnetization Precession at Sub-Terahertz Frequencies in Polycrystalline Cu2 Sb-Type (Mn-Cr)AlGe Ultrathin Films.

A ferromagnetic metal nanolayer with a large perpendicular magnetic anisotropy, small saturation magnetization, and small magnetic damping constant is a crucial requirement for high-speed spintronic devices. Fabrication of these devices on Si/SiO2 amorphous substrates with polycrystalline structure is also strongly desired for the mass production industry. This study involves the investigation of sub-terahertz (THz) magnetization precessional motion in a newly developed material system consisting of Cu2 Sb-type MnAlGe and (Mn-Cr)AlGe films by means of an all-optical pump-probe method. These materials exhibit large perpendicular magnetic anisotropy in regions of a few nanometers in size. The pseudo-2D crystal structures are clearly observed in the high-resolution transmission electron microscopy (TEM) images for the film samples grown on thermally oxidized silicon substrates. The TEM images also show a partial substitution of Cr atoms for the Mn sites in MnAlGe. A magnetization precession frequency of 0.164 THz with a relatively small effective magnetic damping constant of 0.012 is obtained for (Mn-Cr)AlGe. Theoretical calculation infers that the modification of the total density of states by Cr substitution decreases the intrinsic magnetic damping constant of (Mn-Cr)AlGe.

Microstructures and Interface Magnetic Moments in Mn2VAl/Fe Layered Films Showing Exchange Bias.

Heusler alloys are a material class exhibiting various magnetic properties, including antiferromagnetism. A typical application of antiferromagnets is exchange bias that is a shift of the magnetization curve observed in a layered structure consisting of antiferromagnetic and ferromagnetic films. In this study, a layered sample consisting of a Heusler alloy, Mn2VAl and a ferromagnet, Fe, is selected as a material system exhibiting exchange bias. Although the fully ordered Mn2VAl is known as a ferrimagnet, with an optimum fabrication condition for the Mn2VAl layer, the Mn2VAl/Fe layered structure exhibits exchange bias. The appearance of the antiferromagnetic property in the Mn2VAl is remarkable; however, the details have been unclear. To clarify the microscopic aspects on the crystal structures and magnetic moments around the Mn2VAl/Fe interface, cross-sectional scanning transmission electron microscope (STEM) observation, and synchrotron soft X-ray magnetic circular dichroism (XMCD) measurements were employed. The high-angle annular dark-field STEM images demonstrated clusters of Mn2VAl with the L21 phase distributed only around the interface to the Fe layer in the sample showing the exchange bias. Furthermore, antiferromagnetic coupling between the Mn- and Fe-moments were observed in element-specific hysteresis loops measured using the XMCD. The locally ordered L21 phase and antiferromagnetic Mn-moments in the Mn2VAl were suggested as important factors for the exchange bias.

Heusler alloys for spintronic devices: review on recent development and future perspectives.

Heusler alloys are theoretically predicted to become half-metals at room temperature (RT). The advantages of using these alloys are good lattice matching with major substrates, high Curie temperature above RT and intermetallic controllability for spin density of states at the Fermi energy level. The alloys are categorised into half- and full-Heusler alloys depending upon the crystalline structures, each being discussed both experimentally and theoretically. Fundamental properties of ferromagnetic Heusler alloys are described. Both structural and magnetic characterisations on an atomic scale are typically carried out in order to prove the half-metallicity at RT. Atomic ordering in the films is directly observed by X-ray diffraction and is also indirectly probed via the temperature dependence of electrical resistivity. Element specific magnetic moments and spin polarisation of the Heusler alloy films are directly measured using X-ray magnetic circular dichroism and Andreev reflection, respectively. By employing these ferromagnetic alloy films in a spintronic device, efficient spin injection into a non-magnetic material and large magnetoresistance are also discussed. Fundamental properties of antiferromagnetic Heusler alloys are then described. Both structural and magnetic characterisations on an atomic scale are shown. Atomic ordering in the Heusler alloy films is indirectly measured by the temperature dependence of electrical resistivity. Antiferromagnetic configurations are directly imaged by X-ray magnetic linear dichroism and polarised neutron reflection. The applications of the antiferromagnetic Heusler alloy films are also explained. The other non-magnetic Heusler alloys are listed. A brief summary is provided at the end of this review.

Spin-charge conversion in NiMnSb Heusler alloy films.

Half-metallic Heusler alloys are attracting considerable attention because of their unique half-metallic band structures, which exhibit high spin polarization and yield huge magnetoresistance ratios. Besides serving as ferromagnetic electrodes, Heusler alloys also have the potential to host spin-charge conversion. Here, we report on the spin-charge conversion effect in the prototypical Heusler alloy NiMnSb. An unusual charge signal was observed with a sign change at low temperature, which can be manipulated by film thickness and ordering structure. It is found that the spin-charge conversion has two contributions. First, the interfacial contribution causes a negative voltage signal, which is almost constant versus temperature. The second contribution is temperature dependent because it is dominated by minority states due to thermally excited magnons in the bulk part of the film. This work provides a pathway for the manipulation of spin-charge conversion in ferromagnetic metals by interface-bulk engineering for spintronic devices.

Chemical and structural analysis on magnetic tunnel junctions using a decelerated scanning electron beam.

Current information technology relies on the advancement of nanofabrication techniques. For instance, the latest computer memories and hard disk drive read heads are designed with a 12 nm node and 20 nm wide architectures, respectively. With matured nanofabrication processes, a yield of such nanoelectronic devices is typically up to about 90%. To date the yield has been compensated with redundant hardware and software error corrections. In the latest memories, approximately 5% redundancy and parity bits for error corrections are used, which increase the total production cost of the devices. This means the yield directly affects the device costs. It is hence critical to increase the yield in nanofabrication. In this paper, we have applied our recently developed method to image buried interfaces in combination with chemical analysis to evaluate magnetic tunnel junctions and have revealed their different magnetoresistance ratios caused by the presence of materials formed at the junction edges. The formation of these materials can be avoided by optimising the junction patterning process to remove residual carbon introduced from resist. Our imaging method with chemical analysis have demonstrated a significant potential for the improvement of junction performance, resulting in higher yields. This can be used as a quality assurance tool in a nanoelectronic device production line.

Interface Tailoring Effect for Heusler Based CPP-GMR with an L12-Type Ag3Mg Spacer.

Current perpendicular-to-plane (CPP) giant magnetoresistance (GMR) effects are of interest in a possible application of magnetic sensor elements, such as read-head of hard disk drives. To improve the junction performance, the interface tailoring effects were investigated for the Heulser alloy, Co2Fe0.4Mn0.6Si (CFMS), based CPP-GMR junctions with an L 1 2 -Ag3Mg ordered alloy spacer. Ultra-thin Fe or Mg inserts were utilized for the CFMS/Ag3Mg interfaces, and CPP-GMR at low bias current density, J and the J dependence were evaluated for the junctions. Although, at low bias J, MR ratio decreased with increasing the inserts thickness, the device output at high bias J exhibited quite weak dependence on the insert thickness. The output voltages of the order of 4 mV were obtained for the junctions regardless of the insert at an optimal bias J for each. The critical current density J c was evaluated by the shape of MR curves depending on J. J c increased with the insert thicknesses up to 0.45 nm. The enhancement of J c suggests that spin-transfer-torque effect may reduce in the junctions with inserts, which enables a reduction of noise and can be an advantage for device applications.

Voltage control of magnetic anisotropy in epitaxial Ru/Co2FeAl/MgO heterostructures.

Voltage control of magnetic anisotropy (VCMA) in magnetic heterostructures is a key technology for achieving energy-efficiency electronic devices with ultralow power consumption. Here, we report the first demonstration of the VCMA effect in novel epitaxial Ru/Co2FeAl(CFA)/MgO heterostructures with interfacial perpendicular magnetic anisotropy (PMA). Perpendicularly magnetized tunnel junctions with the structure of Ru/CFA/MgO were fabricated and exhibited an effective voltage control on switching fields for the CFA free layer. Large VCMA coefficients of 108 and 139 fJ/Vm for the CFA film were achieved at room temperature and 4 K, respectively. The interfacial stability in the heterostructure was confirmed by repeating measurements. Temperature dependences of both the interfacial PMA and the VCMA effect were also investigated. It is found that the temperature dependences follow power laws of the saturation magnetization with an exponent of ~2, where the latter is definitely weaker than that of conventional Ta/CoFeB/MgO. The significant VCMA effect observed in this work indicates that the Ru/CFA/MgO heterostructure could be one of the promising candidates for spintronic devices with voltage control.

Fully epitaxial C1b-type NiMnSb half-Heusler alloy films for current-perpendicular-to-plane giant magnetoresistance devices with a Ag spacer.

Remarkable magnetic and spin-dependent transport properties arise from well-designed spintronic materials and heterostructures. Half-metallic Heusler alloys with high spin polarization exhibit properties that are particularly advantageous for the development of high-performance spintronic devices. Here, we report fully (001)-epitaxial growth of a high-quality half-metallic NiMnSb half-Heusler alloy films, and their application to current-perpendicular-to-plane giant magnetoresistance (CPP-GMR) devices with Ag spacer layers. Fully (001)-oriented NiMnSb epitaxial films with very flat surface and high magnetization were prepared on Cr/Ag-buffered MgO(001) single crystalline substrates by changing the substrate temperature. Epitaxial CPP-GMR devices using the NiMnSb films and a Ag spacer were fabricated, and room-temperature (RT) CPP-GMR ratios for the C1b-type half-Heusler alloy were determined for the first time. A CPP-GMR ratio of 8% (21%) at RT (4.2 K) was achieved in the fully epitaxial NiMnSb/Ag/NiMnSb structures. Furthermore, negative anisotropic magnetoresistance (AMR) ratio and small discrepancy of the AMR amplitudes between RT and 10 K were observed in a single epitaxial NiMnSb film, indicating robust bulk half metallicity against thermal fluctuation in the half-Heusler compound. The modest CPP-GMR ratios could be attributed to interface effects between NiMnSb and Ag. This work provides a pathway for engineering a new class of ordered alloy materials with particular emphasis on spintronics.

Observation of a large spin-dependent transport length in organic spin valves at room temperature.

The integration of organic semiconductors and magnetism has been a fascinating topic for fundamental scientific research and future applications in electronics, because organic semiconductors are expected to possess a large spin-dependent transport length based on weak spin-orbit coupling and weak hyperfine interaction. However, to date, this length has typically been limited to several nanometres at room temperature, and a large length has only been observed at low temperatures. Here we report on a novel organic spin valve device using C(60) as the spacer layer. A magnetoresistance ratio of over 5% was observed at room temperature, which is one of the highest magnetoresistance ratios ever reported. Most importantly, a large spin-dependent transport length of approximately 110 nm was experimentally observed for the C(60) layer at room temperature. These results provide insights for further understanding spin transport in organic semiconductors and may strongly advance the development of spin-based organic devices.

Note: Probing quadratic magneto-optical Kerr effects with a dual-beam system.

In this Note, we present a dual-beam magneto-optical Kerr effect (MOKE) magnetometer for the study of quadratic MOKE in magnetic thin films. The two beams simultaneously probe the sample, located in the middle of a quadrupole magnet, at two angles of incidence (0 degrees and 45 degrees). This combination of two systems allows one to automatically and routinely perform measurements that are sensitive to the combined longitudinal and quadratic MOKE signals (45 degrees), or the quadratic effect alone (0 degrees). Orientation-dependent and automated quantitative analyses of the quadratic effect's amplitude are also implemented. We present representative measurements on Heusler compound thin films to illustrate the newly combined capabilities of this instrument.

Band-structure-dependent demagnetization in the Heusler alloy Co2Mn(1-x)FexSi.

We investigate the ultrafast demagnetization for two Heusler alloys (Co2Mn(1-x)FexSi) with a different lineup of the minority band gap and the Fermi level. Even though electronic spin-flip transitions are partially blocked by the band gap in one compound, the respective magnetization dynamics, as measured by the time-resolved Kerr effect, are remarkably similar. Based on a dynamical model that includes momentum and spin-dependent carrier scattering, we show that the magnetization dynamics are dominated by hole spin-flip processes, which are not influenced by the gap.