RESUMO
The escalating volume of sewage sludge (SS) generated poses challenges in disposal, given its potential harm to the environment and human health. This study explored sustainable solutions for SS management with a focus on energy recovery. Employing CO2-assisted pyrolysis, we converted SS into flammable gases (H2 and CO; syngas). Single-stage pyrolysis of SS in a CO2 conditions demonstrated that CO2 enhances flammable gas production (especially CO) through gas phase reactions (GPRs) with volatile matter (VM) at temperatures ≥ 520 ËC. Specifically, the CO2 partially oxidized the VM released from SS and concurrently underwent reduction into CO. To enhance the syngas production at temperatures ≤ 520 ËC, multi-stage pyrolysis setup with additional heat energy and a Ni/Al2O3 catalyst were utilized. These configurations significantly increased flammable gas production, particularly CO, at temperatures ≤ 520 ËC. Indeed, the flammable gas yield in the catalytic pyrolysis of SS increased from 200.3 mmol under N2 conditions to 219.2 mmol under CO2 conditions, representing a 4.4-fold increase compared to single-stage pyrolysis under CO2 conditions (50.0 mmol). By integrating a water-gas-shift reaction, the flammable gases produced from CO2-assisted catalytic pyrolysis were expected to have the potential to generate revenue of US$4.04 billion. These findings highlight the effectiveness of employing CO2 in SS pyrolysis as a sustainable and effective approach for treating and valorising SS into valuable energy resources.
RESUMO
In response to address the climate crisis, there has been a growing focus on substituting conventional refinery-derived products with those derived from biorefineries. The utilization of lipids as primary materials or intermediates for the synthesis of chemicals and fuels, which are integral to the existing chemical and petrochemical industries, is a key step in this transition. This review provides a comprehensive overview of the production of sustainable chemicals (acids and alcohols), biopolymers, and fuels (including gasoline, kerosene, biodiesel, and heavy fuel oil) from lipids derived from terrestrial and algal biomass. The production of chemicals from lipids involves diverse methods, including polymerization, epoxidation, and separation/purification. Additionally, the transformation of lipids into biofuels can be achieved through processes such as catalytic cracking, hydroprocessing, and transesterification. This review also suggests future research directions that further advance the lipid valorization processes, including enhancement of catalyst durability at harsh conditions, development of deoxygenation process with low H2 consumption, investigation of precise separation of target compounds, increase in lipid accumulation in algal biomass, and development of methods that utilize residues and byproducts generated during lipid extraction and conversion.
RESUMO
Thermosetting polymers are used in a wide range of applications due to their robust mechanical strength and superior flame retardancy. Despite these technical benefits, recycling of thermosetting polymers has been challenging because of their crosslinking nature. Moreover, their disposal through conventional methods (landfill and combustion) poses environmental concerns, such as microplastics and air pollutants. To address these issues, this study introduces a thermo-chemical disposal platform for thermosetting polymer wastes that employs carbon dioxide (CO2) as a reactive medium. In this work, melamine-formaldehyde was used as model compound of thermosetting polymers. In single-stage pyrolysis, it was revealed that CO2 plays a crucial role in controlling in the compositional matrices of pyrolytic gases, liquid products, and wax. These compositional changes were attributed to the homogeneous reactions between CO2 and the volatile compounds released from the thermolysis of MF. To enhance the thermal cracking of the MF, a double-stage pyrolysis process was tested, which increased the production of pyrolytic gases and eliminated wax formation. However, the slow kinetics governing the reactivity of CO2 limits the occurrence of homogeneous reactions. A nickel-based catalyst was used to accelerate reaction kinetics. The catalytic pyrolysis under CO2 conditions led to substantial increases in syngas (H2 and CO) production of 880% and 460%, respectively, compared with double-stage pyrolysis. These findings demonstrate that thermosetting polymer wastes can be valorized into gaseous fuels through thermo-chemical process, and CO2 enhances the recovery of energy and chemicals. Therefore, this study presents an innovative technical platform to convert thermosetting polymer wastes and CO2 into syngas.
RESUMO
Although biomass is carbon-neutral, its use as a primary feedstock faces challenges arising from inconsistent supply chains. Therefore, it becomes crucial to explore alternatives with reliable availability. This study proposes a strategic approach for the thermochemical valorization of food processing waste, which is abundantly generated at single sites within large-scale processing plants. As a model biomass waste from the food industry, orange peel waste was particularly chosen considering its substantial consumption. To impart sustainability to the pyrolysis system, CO2, a key greenhouse gas, was introduced. As such, this study highlights elucidating the functionality of CO2 as a reactive feedstock. Specifically, CO2 has the potential to react with volatile pyrolysates evolved from orange peel waste, leading to CO formation at ≥490 °C. The formation of chemical constituents, encompassing acids, ketones, furans, phenols, and aromatics, simultaneously decreased by 15.1 area% in the presence of CO2. To activate the efficacy of CO2 at the broader temperature spectrum, supplementary measures, such as an additional heating element (700 °C) and a nickel-based catalyst (Ni/Al2O3), were implemented. These configurations promote thermal cracking of the volatiles and their reaction kinetics with CO2, representing an opportunity for enhanced carbon utilization in the form of CO. Finally, the integrated process of CO2-assisted catalytic pyrolysis and water-gas shift reaction was proposed. A potential revenue when maximizing the productivity of H2 was estimated as 2.62 billion USD, equivalent to 1.11 times higher than the results from the inert (N2) environment. Therefore, utilizing CO2 in the pyrolysis system creates a promising approach for enhancing the sustainability of the thermochemical valorization platform while maximizing carbon utilization in the form of CO.
RESUMO
Plastic-based insulation materials have been widely employed owing to their exceptional durability, cost-effectiveness, low weight, and low thermal conductivity. Nevertheless, the disposal of the insulation material waste (IMW) within construction waste and its recycling and recovery are challenging. Meanwhile, landfilling or incineration methods can release toxic chemicals into the environment. Consequently, the accumulation of IMW in construction waste has become a pressing environmental concern. To address this issue, this paper proposes a pyrolysis platform as a disposal management method for IMW that employs CO2 as a reactive medium. IMW composed of polystyrene in the form of extruded polystyrene underwent pyrolysis to yield pyrogenic products containing toxic chemicals. These toxic chemicals were subsequently transformed into syngas via homogeneous reactions with CO2 under certain thermal conditions and Ni/Al2O3 catalyst. This resulted in a significant reduction in the total peak areas of toxic substances in the pyrogenic oil compared with that obtained using N2 as a medium. Furthermore, the efficacy of CO2 was demonstrated to increase with an increase in the atmospheric concentration. This study implied that catalytic pyrolysis under CO2 conditions is a potential platform for converting toxic chemicals from IMW into syngas through homogeneous reactions with CO2.
RESUMO
This study aimed to investigate bone char's physicochemical transformations through co-torrefaction and co-pyrolysis processes with biomass. Additionally, it aimed to analyze the carbon sequestration process during co-torrefaction of bone and biomass and optimize the process parameters of co-torrefaction. Finally, the study sought to evaluate the arsenic sorption capacity of both torrefied and co-torrefied bone char. Bone and biomass co-torrefaction was conducted at 175 °C-300 °C. An orthogonal array of Taguchi techniques and artificial neural networks (ANN) were employed to investigate the influence of various torrefaction parameters on carbon dioxide sequestration within torrefied bone char. A co-torrefied bone char, torrefied at a reaction temperature of 300 °C, a heating rate of 15 °C·min-1, and mixed with 5 g m of biomass (wood dust), was selected for the arsenic (III) sorption experiment due to its elevated carbonate content. The results revealed a higher carbonate fraction (21%) in co-torrefied bone char at 300 °C compared to co-pyrolyzed bone char (500-700 °C). Taguchi and artificial neural network (ANN) analyses indicated that the relative impact of process factors on carbonate substitution in bone char followed the order of co-torrefaction temperature (38.8%) > heating rate (31.06%) > addition of wood biomass (30.1%). Co-torrefied bone chars at 300 °C exhibited a sorption capacity of approximately 3 mg g-1, surpassing values observed for pyrolyzed bone chars at 900 °C in the literature. The findings suggest that co-torrefied bone char could serve effectively as a sorbent in filters for wastewater treatment and potentially fulfill roles such as a remediation agent, pH stabilizer, or valuable source of biofertilizer in agricultural applications.
Assuntos
Arsênio , Biomassa , Carvão Vegetal , Águas Residuárias , Poluentes Químicos da Água , Arsênio/análise , Arsênio/química , Carvão Vegetal/química , Águas Residuárias/química , Poluentes Químicos da Água/análise , Poluentes Químicos da Água/química , Adsorção , Osso e Ossos/química , Redes Neurais de Computação , Animais , PiróliseRESUMO
This study explored the valorisation of silkworm by-product, a major by-product of the silk industry (sericulture), which amounts to 16 million tonnes annually. The focus was on transforming waste into energy resources through pyrolysis under CO2 conditions. In one-stage pyrolysis, the evolution of syngas under N2 was found to be comparable to that under CO2. A notable allocation of carbon to biocrude rather than syngas was observed. The two-stage pyrolysis resulted in increased syngas production. However, achieving a homogeneous reaction between CO2 and the volatiles liberated from silkworm byproduct proved challenging. Indeed, the reaction kinetics governing CO2 reactivity was not fast although the temperature windows of the reaction were aligned in the two-stage pyrolysis. To address this issue, pyrolysis was performed using a Ni-based catalyst to expedite the reaction kinetics. Consequently, syngas formation, particularly CO formation, was significantly enhanced under CO2 conditions compared to that under N2 conditions. The syngas yield under CO2 was 36.42 wt% which was 2-fold higher than that of N2. This suggested the potential of CO2 altering the carbon distribution from biocrude to syngas. This strategy would contribute to the establishment of sustainable production of silk by converting sericulture by-product into energy/chemical resources.
Assuntos
Bombyx , Dióxido de Carbono , Animais , Carbono , Temperatura , SedaRESUMO
Torrefaction is an effective pathway for microalgal solid biofuel upgrading, and alkali metal activation is also an efficient method to enhance fuel properties. This study explores the comparison of torrefaction alone and KOH activation combined with torrefaction to determine a better operation for biochar production from the microalga Nannochloropsis Oceanica. The results indicate that the HHV ranges of KOH-activated biochar and unactivated biochar are 25.611-32.792 MJ·kg-1 and 25.024-26.389 MJ·kg-1, respectively. Furthermore, KOH-activated biochar is better than unactivated biochar, with less residue, broader pyrolysis and combustion temperature ranges, higher elemental carbon, and less combined carbon. Moreover, KOH-activated biochar is close to the unactivated one from the viewpoint of expense calculation and life cycle assessment and thus possesses a better comprehensive performance. Overall, KOH activation is an efficient method for upgrading microalgal solid biofuel. The results are conducive to exploring further modification of microalgal solid biofuel production with better properties, thus leading to a greener and more efficient approach for upgrading fuel performance.
Assuntos
Microalgas , Água/química , Biocombustíveis , Biomassa , Carvão Vegetal , TemperaturaRESUMO
Using edible lipids for biodiesel production has been criticized, causing biodiesel production from inedible food resources to be desirable. Lipid extraction must be prioritized to produce biodiesel using an acid/base-catalyzed transesterification process, but this conversion process suffers from technical reliability. Therefore, this study introduced non-catalytic conversion of oil-bearing biomass into biodiesel. Apricot seeds were used as a model compound (oil content 44.3 wt%). The non-catalytic transesterification of apricot seed oil recovered 98.28 wt% biodiesel at 360 °C for 1 min, while alkali-catalysis of apricot seed oil recovered 91.84 wt% at 63 °C for 60 min. The direct conversion of apricot seeds into biodiesel was attempted. The trends in the yields of biodiesel from apricot seeds and seed oil obtained by non-catalytic transesterification as a function of reaction temperature were similar. The yield of biodiesel from apricot seed was 43.06 wt%, suggesting that 97.20 wt% of lipids were converted into biodiesel.
Assuntos
Prunus armeniaca , Biocombustíveis , Reprodutibilidade dos Testes , Esterificação , Ácidos Graxos , Sementes , Óleos de Plantas , CatáliseRESUMO
A large amount of manure is generated from concentrated animal feeding operations (CAFOs), leading to serious environmental issues and hazardous risks from pathogens, such as methicillin-resistant Staphylococcus aureus. Therefore, developing an effective method for manure disposal is essential. Thus, in this study, we suggest the use of CO2 in pyrolysis of hen manure (HM) as an effective method to convert the carbon in HM into syngas (especially carbon monoxide (CO)). HM was used and tested as the model compound. From the results of thermo-gravimetric analysis, the decarboxylation of CaCO3 in HM in the presence of N2 was realized at temperatures ranging from 638 to 754 °C. The Boudouard reaction was observed at ≥ 664 °C in the presence of CO2. Despite the lack of occurrence of the Boudouard reaction, more CO formation was observed in the presence of CO2 at ≥ 460 °C. This was deemed as a homogeneous reaction induced by CO2. Considering the high Ca content of HM, HM biochar in N2 and CO2 were used as adsorbent for removal of Cadmium (Cd), which is toxic heavy metal. The adsorption capacities of HM_N2 and HM_CO2 were 302.4 and 95.7 mg g-1, respectively. The superior performance of HM_N2 is mainly attributed to the presence of Ca(OH)2, which provides favorable (alkaline) conditions for precipitation and ion exchange. Our results indicate the environmental benefits from using CO2. Specifically, CO2 (representative greenhouse gas) converted into fuel. Given this, pyrolysis of HM in the presence of CO2 was achieved at ≤ 640 °C, and the atmospheric condition should be switched from CO2 to N2 at ≥ 640 °C to ensure the decarboxylation of CaCO3.
Assuntos
Cádmio , Staphylococcus aureus Resistente à Meticilina , Animais , Feminino , Esterco , Pirólise , Dióxido de Carbono , Galinhas , Carvão VegetalRESUMO
Researchers have focused on efficient techniques for degrading hazardous organic pollutants due to their negative impacts on ecological systems, necessitating immediate remediation. Specifically, TiO2-based photocatalysts, a wide-bandgap semiconductor material, have been extensively studied for their application in environmental remediation. However, the extensive band gap energy and speedy reattachment of electron (e-) and hole (h+) pairs in bare TiO2 are considered major disadvantages for photocatalysis. This review extensively focuses on the combination of semiconducting photocatalysts for commercial outcomes to develop efficient heterojunctions with high photocatalytic activity by minimizing the e-/h+ recombination rate. The improved activity of these heterojunctions is due to their greater surface area, rich active sites, narrow band gap, and high light-harvesting tendency. In this context, strategies for increasing visible light activity, including doping with metals and non-metals, surface modifications, morphology control, composite formation, heterojunction formation, bandgap engineering, surface plasmon resonance, and optimizing reaction conditions are discussed. Furthermore, this review critically assesses the latest developments in TiO2 photocatalysts for the efficient decomposition of various organic contaminants from wastewater, such as pharmaceutical waste, dyes, pesticides, aromatic hydrocarbons, and halo compounds. This review implies that doping is an effective, economical, and simple process for TiO2 nanostructures and that a heterogeneous photocatalytic mechanism is an eco-friendly substitute for the removal of various pollutants. This review provides valuable insights for researchers involved in the development of efficient photocatalysts for environmental remediation.
Assuntos
Poluentes Ambientais , Recuperação e Remediação Ambiental , Titânio/química , Catálise , LuzRESUMO
Crop residues are affordable lignocellulosic waste in the world, and a large portion of the waste has been burned, releasing toxic pollutants into the environment. Since the crop residue is a carbon and ingredient rich material, it can be strategically used as a sorptive material for (in)organic pollutants in the wastewater after thermo-chemical valorization (i.e., biochar production). In this review, applications of crop residue biochars to adsorption of non-degradable synthetic dyes, antibiotics, herbicides, and inorganic heavy metals in wastewater were discussed. Properties (porosity, functional groups, heteroatom, and metal(oxide)s, etc.) and adsorption capacity relationships were comprehensively reviewed. The current challenges of crop residue biochars and guidelines for development of efficient adsorbents were also provided. In the last part, the future research directions for practical applications of the crop residue biochars in wastewater treatment plants have been suggested.
Assuntos
Poluentes Ambientais , Águas Residuárias , Adsorção , AntibacterianosRESUMO
Odor is a critical environmental problem that negatively affects people's quality of life. Wastewater treatment plants (WWTPs) often emit various odorous compounds, such as ammonia, sulfur dioxide, and organosulfur. Abatement of odor emissions from WWTPs using biochar may contribute to achieving carbon neutrality due to the carbon negative nature, CO2 sorption, and negative priming effects of biochar. Biochar has a high specific surface area and microporous structure with appropriate activation, which is suitable for sorption purposes. Various research directions have been proposed to determine the biochar removal efficiency for different odorants released from WWTPs. According to the literature survey, the pre- and post-treatments (e.g., thermal treatment, chemical treatment, and metal impregnation) of biochar could enhance the removal capacity for the odorants emitted from WWTPs at comparable conditions, compared to unmodified biochar. The feedstock and production condition (particularly, pyrolysis temperature) of a biochar and initial concentration of an odorant markedly affect the biochar's odorant removal capacity and efficiency. Moreover, different adsorption systems for the removal of odorants emitted from WWTPs follow different adsorption models. Further research is required to establish the practical use of biochar for the mitigation of odors released from WWTPs.
RESUMO
Biochar is of great importance to realizing solid biowastes reduction and environmental remediation. Modifying biochar for better performance is also of great concern to achieve property improvement. P-doped biochar from soybean straw is prepared for multistage utilization to realize water pollutant removal and biofuel usage. The results suggest that the prepared biochar is adequate for sulfadiazine adsorption and has stable performance under coexisting ions and aquatic pH. Furthermore, the higher heating value of the biochar is close to coal and thus can be an alternative to fossil fuel. The maximum sulfadiazine adsorption amount of P-doped biochar is 252.24 mg·g-1, and the P-doped biochar HHV is 24 MJ·kg-1 which can be an alternative to coal. The greenhouse gas and pollutant emission potential are also considered to explore the environmental impact of P-doped biochar production and usage. Overall, the optimal ratio of soybean straw: K3PO4 is 3:1.
Assuntos
Poluentes Ambientais , Glycine max , Biocombustíveis , Carvão Mineral , SulfadiazinaRESUMO
Biochar, a carbon-rich and por ous material derived from waste biomass resources, has demonstrated tremendous potential in wastewater treatment. Torrefaction technology offers a favorable low-temperature biochar production method, and torrefied biochar can be used not only as a solid biofuel but also as a pollutant adsorbent. This review compares torrefaction technology with other thermochemical processes and discusses recent advancements in torrefaction techniques. Additionally, the applications of torrefied biochar in wastewater treatment (dyes, oil spills, heavy metals, and emerging pollutants) are comprehensively explored. Many studies have shown that high productivity, high survival of oxygen-containing functional groups, low temperature, and low energy consumption of dried biochar production make it attractive as an adsorbent for wastewater treatment. Moreover, used biochar's treatment, reuse, and safe disposal are introduced, providing valuable insights and contributions to developing sustainable environmental remediation strategies by biochar.
Assuntos
Poluentes Ambientais , Águas Residuárias , Temperatura , Carvão Vegetal , CarbonoRESUMO
Pine wastes, including pine needles, cones, and wood, are abundantly produced as an agroforestry by-product globally and have shown tremendous potential for biochar production. Various thermochemical conversion technologies have exhibited promising results in converting pine wastes to biochar, displaying impressive performance. Hence, this review paper aims to investigate the possibilities and recent technological advancements for synthesizing biochar from pine waste. Furthermore, it explores techniques for enhancing the properties of biochar and its integrated applications in various fields, such as soil and water remediation, carbon sequestration, battery capacitor synthesis, and bio-coal production. Finally, the paper sheds light on the limitations of current strategies, emphasizing the need for further research and study to address the challenges in pine waste-based biochar synthesis. By promoting sustainable and effective utilization of pine wastes, this review contributes to environmental conservation and resource management.
Assuntos
Carvão Vegetal , Pinus , Carvão Vegetal/química , Solo/química , MadeiraRESUMO
While transition metals are useful for activating monopersulfate (MPS) to degrade contaminants, bimetallic alloys exhibit stronger catalytic activities owing to several favorable effects. Therefore, even though Co is an efficient metal for MPS activation, CoFe alloys are even more promising heterogeneous catalysts for MPS activation. Immobilization/embedment of CoFe alloy nanoparticles (NPs) onto hetero-atom-doped carbon matrices appears as a practical strategy for evenly dispersing CoFe NPs and enhancing catalytic activities via interfacial synergies between CoFe and carbon. Herein, N-doped carbon-embedded CoFe alloy (NCCF) is fabricated here to exhibit a unique hollow-engineered nanostructure and the composition of CoFe alloy by using Co-ZIF as a precursor after the facile etching and Fe doping. The Fe dopant embeds CoFe alloy NPs into the hollow-structured N-doped carbon substrate, enabling NCCF to possess the higher mesoscale porosity, active N species as well as more superior electrochemical properties than its analogue without Fe dopants, carbon matrix-supported cobalt (NCCo). Thus, NCCF exhibits a considerably larger activity than NCCo and the benchmark catalyst, Co3O4 NP, for MPS activation to degrade an environmental hormone, dihydroxydiphenyl ketone (DHPK). Besides, NCCF + MPS shows an even lower activation energy for DHPK degradation than literatures, and retains its high efficiency for eliminating DHPK in different water media. DHPK degradation pathway and ecotoxicity assessment are unraveled based on the insights from the computational chemistry, demonstrating that DHPK degradation by NCCF + MPS did not result in the formation of toxic and highly toxic by-products. These features make NCCF a promising heterogeneous catalyst for MPS activation to degrade DHPK.
RESUMO
The Fenton-like reaction is a promising organic wastewater treatment reaction among advanced oxidation processes (AOP), which has emerged to replace the conventional Fenton reaction. Recycled construction and demolition waste (CDW), which is porous and rich in iron, manganese, and magnesium, can be reused as a Fenton-like catalyst. This study proposes an AOP wastewater treatment strategy using recycled porous CDW mixed with hydrogen peroxide (H2O2) to decompose methylene blue (MB) wastewater. According to the apparent first-order rate (Kapp) of 10 ppm MB adsorption, CDW-3, having the highest specific surface area, also has the highest Kapp of 0.23 min-1 g-1. The optimized conditions recommended by the Taguchi method include a 0.3 g mL-1 CDW-3 concentration, a 0.254 g mL-1 H2O2 concentration, and 10 ppm MB, resulting in an about 2.01 min-1Kapp value. In addition, MB concentration is observed as the most influential factor for Kapp, which decreases with increasing MB concentration and is about 0.62 min-1 at 1000 ppm MB. Repeating the Fenton-like reaction five times at 100 p.m. MB using the same CDW-3, the Kapp is about 0.64 min-1, which is 86% of the initial run. The synergistic effect index (ξ) is defined to quantify the level of interaction between CDW and H2O2, which produces free radicals during the Fenton-like process. The ξ of CDW-3 is about 2.16. Overall, it is demonstrated that CDW is a promising catalyst for Fenton-like reactions, and the synergistic effect index (ξ) can be used as a reference index to evaluate the catalytic generation of free radicals between the catalyst and H2O2.
Assuntos
Poluentes Ambientais , Peróxido de Hidrogênio , Águas Residuárias , Ferro , Oxirredução , Azul de MetilenoRESUMO
Since the COVID-19 outbreak, the use of disposable plastics has rapidly increased along with the amount of plastic waste. During fragmentation, microplastics and other chemical substances contained in plastics are released. These then enter humans through food which could be problematic considering their hazardous potential. Polystyrene (PS), which is widely used in disposable containers, releases large amounts of microplastics (MPs), but no studies have investigated the release mechanisms of PS-MPs and simultaneously exposed contaminants. Therefore, in this study, the effects of pH (3, 5, 7, and 9), temperature (20, 50, 80, and 100 °C), and exposure time (2, 4, 6, and 8 h) on MPs release were systematically examined. A quantitative/qualitative study of MPs and styrene monomers was performed using microscopy-equipped Fourier-transformed infrared spectroscopy and gas chromatography-mass spectrometry. The release of PS-MPs (36 items/container) and simultaneously exposed pollutants (SEP), such as ethylene glycol monooleate (EGM), was highest at pH 9, 100 °C, and 6 h, which was proportional to the test temperature and time. Under the same conditions, 2.58 µg/L of styrene monomer migrated to the liquid food simulants. The fragmentation was proceeded by oxidation/hydrolysis and accelerated by increased temperature and exposure time. The strong positive correlation between PS-MPs and SEPs releases at pH and temperature indicates that PS-MPs and SEPs follow the same release process. However, a strongly negative correlation between PS-MPs and styrene monomers at the exposed time shows that styrene migration does not follow the same release process, but does its partition coefficient.
RESUMO
The massive generation of synthetic textile waste has drawn considerable attention. Landfilling/incineration of textile waste has been widely made. To abate the environmental burdensome from the conventional management processes, a thermo-catalytic conversion was used for rapid volume reduction of textile waste and simultaneous valorization by recovering textile monomer in this study. Stockings were chosen as a model feedstock. Because stockings consisted of nylon with other contents, different products (caprolactam (nylon monomer), imines, cyclic dimers, and azepines) were recovered. The yield of caprolactam from the thermal conversion at 500 °C was 53.6 wt%. To selectively enhance the caprolactam yield, catalytic pyrolysis was done using γ-Al2O3 supported metal catalysts (Ni, Cu, Fe, or Co). γ-Al2O3 itself increased the caprolactam yield up to 69.0 wt% via a based-catalyzed reaction of nylon depolymerization and intramolecular cyclization. Under the presence of metal catalysts, the caprolactam yield increased up to 73.3 wt%. To offer desired feature of green chemistry, CO2 was adopted as reactive gas. Under the CO2-mediated catalytic pyrolysis, caprolactam yield was enhanced up to 77.1 wt% over Cu/Al2O3 (basis: stocking mass). Based on the net content of nylon in the stockings, the yield of caprolactam was deemed 95.3 wt%. This study proves that textile waste (stocking) and CO2 are useful resources for recovery of nylon monomer, which can reduce the waste generation with simultaneous recovery of value-added product.