High-frequency ultrasonography but not 930-nm optical coherence tomography reliably evaluates melanoma thickness in vivo: a prospective validation study.

BACKGROUND: Early diagnosis and rapid surgical excision are essential for improving the prognosis of patients with melanoma. Reflectance confocal microscopy has been validated as a feasible procedure for in vivo diagnosis of melanoma but cannot be used to measure tumour thickness. However, ultrasonography and optical coherence tomography may allow melanoma thickness to be measured in vivo. OBJECTIVES: To validate the accuracy and reliability of high-frequency ultrasonography (HFUS) and optical coherence tomography for assessing melanoma thickness in vivo. METHODS: We conducted a prospective study on 131 patients with at least one equivocal melanocytic lesion. Each lesion underwent optical coherence tomography and HFUS assessment, followed by excision and pathological examination. Histopathology was considered to be the gold standard for assessing melanoma thickness. Repeatability, inter- and intrarater reproducibility and reliability were evaluated for each imaging procedure. RESULTS: Ultrasonography showed a good level of agreement with histology [intraclass correlation coefficient (ICC) 0.807; 95% confidence interval (CI) 0.703-0.877] and excellent inter-rater reproducibility (G = 0.97), resulting in reliable in vivo assessment of melanoma thickness. The 930-nm optical coherence tomography showed a poor level of agreement with histopathology (ICC 0.0; 95% CI -0.2-0.2) and the inter-rater reproducibility was null (G = 0.00). CONCLUSIONS: HFUS is a reliable and reproducible noninvasive method for assessing melanoma thickness. Routine use of HFUS may allow single-step excision of equivocal melanocytic lesions, with surgical margins determined by in vivo assessment of tumour thickness.

Dual-parameter optimisation of the elastic properties of skin.

This paper presents a procedure for characterising the mechanical properties of skin using stochastic inverse identification. It is based on the minimisation of a cost function relative to the comparison between experimental suction experiments and their corresponding finite element models. Two different models are compared: a classical single-layer approach and a dual-layer medium which account for both the dermis and the hypodermis. Finite element results are used to construct the pre-optimisation database which is required for the inverse analysis. To compare the calculations, the entire identification is based on a dual-parameter optimisation procedure: for the single-layer approach a quadratic hyperelastic constitutive equation is used, whereas for the dual-layer medium a simple neo-Hookean potential is used. Theoretical conclusions, which are developed first, are then compared with actual case studies.

Human immunodeficiency virus atropy induces modification of subcutaneous adipose tissue architecture: in vivo visualization by high-resolution magnetic resonance imaging.

BACKGROUND: Human immunodeficiency virus (HIV) infection generally induces lipodystrophy. For targeted treatment a better understanding of its development is necessary. The utility of high-resolution magnetic resonance imaging (MRI) is explored. OBJECTIVES: The present study presents a way to visualize the adipose tissue architecture in vivo and to inspect modifications associated with the atrophy. METHODS: High-resolution MRI scans with surface coils were performed on the calf and at the lumbar region of three groups of patients: HIV patients with lipoatrophy, HIV patients without lipoatrophy and healthy volunteers. All patients underwent a clinical examination. In addition, dual energy X-ray absorptiometry (DEXA) measurements were taken. On the MRI scans adipose tissue thickness and adipose nodule size were measured. Results High-resolution MRI enabled identification of a clear disorganization of adipose tissue in patients with lipoatrophy. In addition, these patients presented a very small adipose tissue thickness on the calf and a very small nodule size. RESULTS: led to the hypothesis that adipose tissue disorganization appears before changes in DEXA measurements or clinically visible modifications. CONCLUSIONS: High-resolution MRI enabled visualization in vivo of precise changes in tissue organization due to HIV lipoatrophy. This imaging technique should be very informative for better monitoring of the atrophy.

A multitechnique evaluation of topical corticosteroid treatment.

BACKGROUND/PURPOSE: Corticosteroids are widely prescribed for systemic or local treatment of inflammatory autoimmune disorders. Long-term therapy is associated with side effects and causes cutaneous atrophy of the epidermis and the dermis. The present study aims to evaluate with several noninvasive techniques, the skin modifications observed during corticosteroids treatment. The potential of skin mechanical measurement and ultrasound radio frequency (RF) signal analysis are proposed as new measures more closely related to the functional impairments. METHODS: Thirteen young healthy women volunteers had two applications per day on one arm of topical Clobetasol propionate 0.05% for 28 days, and they were followed for 28 days more. Skin modifications were studied by high-frequency ultrasound imaging, ultrasound RF signal analysis, optical coherence tomography and by the suction test. RESULTS: For all the techniques, a statistically significant change is observed with treatment. Large variations, around 30%, are observed for all techniques, but less for ultrasound imaging (10%). Dermis and epidermis thickness presented stable measurements on the nontreated zone. At the end of the study, measures returned to normal. The dynamic is mainly observed within the first 14 days of treatment and within the first 14 days after its cessation. CONCLUSION: Similar dynamics of skin modification during corticosteroid treatment was observed with very different techniques. Moreover, the potential of RF ultrasound analysis and mechanical skin measurement for characterizing skin structural and functional impairments has been evaluated.

Quantitative magnetic resonance imaging of subcutaneous adipose tissue.

BACKGROUND/PURPOSE: Quantitative transverse relaxation time (T(2)) magnetic resonance (MR) imaging has been used with the aim to characterize subcutaneous adipose tissue. Protons in adipose tissue have a fast exchange behavior giving bi-component transverse relaxation processes with short and long relaxation time values depending on the tissue properties. METHODS: MR images were acquired on a 1 T Siemens MR scan using a multi-spin-echo sequence. A high sensitive surface coil, enabling low noise MR images with voxel size of 10 mm(3), was used for performing accurate quantitative T(2) imaging. These acquisition parameters were determined by a preliminary study performed on an oil phantom known to be a valuable model for mimicking in vivo adipose tissue. In vivo study of the thigh adipose tissue was carried out on 30 volunteers. 20 women with various clinically diagnosed cellulite grades and 10 males, among them five showed overweight. Tissue characterization was finally performed through the analysis of the T(2) distributions. RESULTS: Phantom study showed that improvements in the precision in T(2) measurement are obtained at the expense of the spatial resolution. Uncertainties in T(2) measurements are three times lower by considering a region of interest of 3 x 3 pixels compared with a pixel by pixel analysis. The in vivo study showed that women groups present higher mean short T(2S) component values than men. Histogram of T(2) distribution showed that the maximum amplitude is observed at a lower value for the overweight men group. In addition, larger values around the septae were visualized on the long relaxation time images. CONCLUSIONS: This study shows that precise T(2) map of adipose tissue can be computed. The balance between precision and spatial resolution is examined. Preliminary results relative to tissue organization and to difference between clinical groups proves the potential of the quantitative MRI.

Validation of a non-contact technique for local skin temperature measurements.

UNLABELLED: Here we propose to quantify local temperature variations using thermal imaging to assess the effect of dermatological lasers. OBJECTIVES: To quantify the temperature raise induced by laser application and to differentiate the effects of a potassium titanyl phosphate (KTP) laser and an intense pulsed light (IPL). METHODS: A randomized comparative study was performed on 10 adult volunteers with symmetrical rosacea treated by KTP laser or IPL. Skin temperature measurements were performed on inclusion, immediately after laser treatment and 3 min after thermal water application, using a high-resolution (0.08 degrees C) infrared thermal video camera. RESULTS: KTP laser treatment induced a significant rise in local skin temperature whereas no significant change was revealed by the IPL treatment. The infrared camera is a reliable and reproducible technique that allows a follow-up of skin temperature without skin contact. CONCLUSION: Thermography using an infrared camera could potentially be applied in clinical pharmacology for inflammatory reactions or scarring processes.

A nonlinear elastic behavior to identify the mechanical parameters of human skin in vivo.

BACKGROUND/PURPOSE: Various analyses have been performed to identify the mechanical properties of the human skin tissue in vivo. They generally use different approaches and hypotheses (behavior laws as well as mechanical tests) and the obtained results are consequently difficult to analyze and compare. In this paper, an inverse method that can be adapted to any kind of mechanical tests and behavior laws is presented. METHOD: A suction deformation performed on the volar aspect of the forearm of a subject is considered. This test is modeled with the finite element method to compare the experimental and simulated curves using an inverse method that allows the skin mechanical parameters identification. This process is based on two optimization algorithms, Kalman's filter and Gauss-Newton's methods. To account for the nonlinear behavior of the skin, a specific nonlinear elastic law, which is then compared with standard linear elastic and neo-Hookean's mechanical behaviors, was developed. RESULTS: The obtained results first prove that neither linear elasticity nor neo-Hookean's laws can be used to model the skin. On the contrary, the nonlinear elastic model presents a relevant fit of the experimental curves. The skin thickness is also proved to be another key point to be taken into consideration. CONCLUSIONS: The obtained results are successfully compared with literature and the reliability of the proposed method is underlined with the identification of 300 additional experimental curves. The different works we are currently focusing on are finally introduced.

A randomized, prospective study using the LPG technique in treating radiation-induced skin fibrosis: clinical and profilometric analysis.

BACKGROUND/PURPOSE: Cutaneous fibrosis is the quite mandatory sequela after a breast cancer treated by radiotherapy and it induces more or less important functional troubles. The LPG technique is a technique of mechanical massage that allows skin mobilization by folding/unfolding. The aim of this study was to evaluate the changes on irradiated skin before and after LPG treatment by clinical and skin replica analysis. METHODS: Twenty women, 43-55 years old, who had been treated from 6 to 16 months before, for breast cancer with a conservative surgery and radiotherapy, had been enrolled in the trial. They were divided into two groups after randomization: the first group was LPG treated three times a week for 1 month; the second group was only placed under medical supervision. The clinical criteria studied were systematically studied before (T0), at the end of treatment (T1) and 1 month after the end of treatment (T2): pain, itching, skin dryness, erythema, skin infiltration, feeling of tightness and of induration of the skin. Softening of the skin was assessed at T1 and T2. Cutaneous replica was performed on the internal upper 1/4 of each breast with silicone material before, after and 1 month later after the end of the treatment. After polymerization, the replica was stored and then blindly analyzed by image analysis software. The following parameters were systematically measured: average skin roughness, average of wrinkles' depth and residual length, wrinkle number and the space between them. RESULTS: Clinically, the LPG treatment induced a decrease of erythema (10% of the patients vs. 40% before treatment), a decrease of pain and pruritus (10% vs. 20% and 40%, respectively) and a decrease of the feeling of induration of the skin (10% of the patients vs. 70% before treatment). Furthermore, a skin-softening sensation was noted by seven patients vs. one in the control group. Replica shows an increase of roughness and of furrow depth without any change in the residual length and an increase in the space between the wrinkles, whose number decreases. CONCLUSION: This study confirms the impact of the clinical sequelae induced on skin after radiotherapy and shows improvement of the clinical signs after treatment by the LPG technique. The latter induces changes of micro relief, suggesting a softening effect on the skin. These preliminary results have to be confirmed on a more important group of patients.

In vivo visualization of hyaluronic acid injection by high spatial resolution T2 parametric magnetic resonance images.

BACKGROUND/PURPOSE: In recent years, increasing use of injectable resorbable fillings has been reported for facial wrinkle treatment. However, the physiological processes involved such as the localization and subsequent diffusion of the injected product in skin tissues are poorly documented. This may be noninvasively achieved using quantitative magnetic resonance imaging (MRI), which is duly presented in this pilot study. METHODS: Hyaluronic acid (HA) was injected intradermally in the forearm of a young male volunteer. High-resolution MRI scans using a surface antenna were performed just after injection, and after 2, 4 and 9 months. Morphological images were compared with transverse relaxation time (T(2)) images computed from a pixel-by-pixel analysis. RESULTS: On high-resolution morphological MR images the HA injection is barely visible, but with quantitative MRI the zone of injection is clearly seen. This is due to HA having a distinctly different transverse relaxation time, T(2) approximately 600 ms, compared with dermal and hypodermal tissues, 35 and 80 ms, respectively. CONCLUSION: These preliminary results demonstrate the ability of the T(2) images for in vivo visualization of the filler agent and also for characterization of tissue modifications. In addition, the diffusion and progressive degradation of the filler agent can be monitored by T(2) measurements over time.

Use of a 3-D imaging technique for non-invasive monitoring of the depth of experimentally induced wounds.

BACKGROUND/PURPOSE: Experimental studies of wound healing lack methods for standardized wounding and in situ depth assessment. Consequently, in this pilot study, an Erbium (Er):YAG laser has been used for wound induction with a non-invasive 3-D imaging technique as an alternative to histology. METHODS: Erbium:YAG ablation of human skin ex vivo was performed with total fluences of 10, 50 and 200 J/cm(2), removing the stratum corneum, epidermis/papillary dermis and deeper dermis, respectively. Wound depth was measured with the 3-D method and histologically. RESULTS: Wound depth was proportional to fluence for both techniques : 3-D, 17.7+/-1.7, 43.9+/-16 and 245.2+/-61 microm; histology, 14.6+/-1.7, 50.6+/-11.6 and 238+/-102 microm, respectively. CONCLUSIONS: The 3-D technique compares well with and is an improvement on histological measurement, providing true wound depth measurement, avoiding shape changes inherent with histology. Furthermore, the Er:YAG laser is a highly appropriate means of wound induction due to its rapidity and precision.

High spatial resolution quantitative MR images: an experimental study of dedicated surface coils.

Measuring spin-spin relaxation times (T2) by quantitative MR imaging represents a potentially efficient tool to evaluate the physicochemical properties of various media. However, noise in MR images is responsible for uncertainties in the determination of T2 relaxation times, which limits the accuracy of parametric tissue analysis. The required signal-to-noise ratio (SNR) depends on the T2 relaxation behaviour specific to each tissue. Thus, we have previously shown that keeping the uncertainty in T2 measurements within a limit of 10% implies that SNR values be greater than 100 and 300 for mono- and biexponential T2 relaxation behaviours, respectively. Noise reduction can be obtained either by increasing the voxel size (i.e., at the expense of spatial resolution) or by using high sensitivity dedicated surface coils (which allows us to increase SNR without deteriorating spatial resolution in an excessive manner). However, surface coil sensitivity is heterogeneous, i.e., it--and hence SNR--decreases with increasing depth, and the more so as the coil radius is smaller. The use of surface coils is therefore limited to the analysis of superficial structure such as the hypodermic tissue analysed here. The aim of this work was to determine the maximum limits of spatial resolution and depth compatible with reliable in vivo T2 quantitative MR images using dedicated surface coils available on various clinical MR scanners. The average thickness of adipose tissue is around 15 mm, and the results obtained have shown that obtaining reliable biexponential relaxation analysis requires a minimum achievable voxel size of 13 mm3 for a conventional volume birdcage coil and only of 1.7 mm3 for the smallest available surface coil (23 mm in diameter). Further improvement in spatial resolution allowing us to detect low details in MR images without deteriorating parametric T2 images can be obtained by image filtering. By using the non-linear selective blurring filter described in a previous work, the voxel size was reduced to 0.8 mm3, allowing us to detect microstructures such as fibrous septae while preserving precision in T2 measurements. This paper provides practical information allowing us to perform reliable T2 quantitative MR micro images. High resolution imaging with dedicated surface coils, which is only well-suited to near surface organs, might lead to highly valuable results in this context, especially to analyse the hypodermis involved in the lipodystrophy seen in patients with human immuno-deficiency virus (HIV).

Image analysis of skin scaling using D-Squame samplers: comparison with clinical scoring and use for assessing moisturizer efficacy.

The severity of scaling disorders can be evaluated objectively using the D-Squame technique coupled with image analysis. The parameters of scaling derived using this approach need to be clinically relevant and should have greater discrimination than visual grading. Improvements to an existing method that fulfil these requirements are presented. Three scaling parameters were calculated using image analysis of digitized video-captured images of obliquely lit D-Squame samples. These parameters were compared to clinical scores of scaling made by five observers from photographs of the same areas sampled with D-Squame. In addition, two clinical studies were carried out to assess moisturizer effects on different degrees of xerosis, and to compare two different moisturizer preparations. The three scaling parameters gave correlation coefficients, r, between 0.6 and 0.75 when compared with global clinical scores of scaling. Significant reductions in all parameters were observed with 2 weeks of moisturizer use on lower leg skin with marked xerosis compared to an untreated control. The same moisturizer had a similar effect on milder xerosis of the forearm, and showed a greater decrease than a moisturizer with lower glycerol content. Increases in skin hydration, as measured with a corneometer, were also seen in both clinical studies, and corresponded well with D-Squame results. Differences in the degrees of scaling between these two anatomical sites were also detected with this technique. In a previous publication, the same technique was shown to be repeatable and reproducible; in the current article its correlation with clinical observations of scaling or flaking skin has been demonstrated.

A post-processing method for multiexponential spin-spin relaxation analysis of MRI signals.

Quantitative MR imaging is a potential tool for tissue characterization; in particular, proton density and proton relaxation times can be derived from MR signal analysis. However, MR image noise affects the accuracy of measurements and the number of tissue parameters that can be reliably estimated. Filtering can be used to limit image noise; however this reduces spatial resolution. In this work we studied, using both simulations and experiments, a filter called a 'selective blurring filter'. Compared to other classical filters, this filter achieves the best compromise between spatial resolution and noise reduction. The filter was specifically used to reliably determine the bi-component transverse relaxation of protons in adipose tissue. Long and short relaxation times and the relative proton fraction of each component were obtained with a degree of uncertainty of less than 10% and an accuracy of 95%.

Topography and anisotropy of the skin surface with ageing.

BACKGROUND/PURPOSE: Most studies of how the relief of the skin surface changes on ageing are based solely on topography, and a few have taken into account anisotropy parameters. However, the calculation of these parameters is often carried out manually and as the techniques of data acquisition have progressed rapidly, a certain degree of obsolescence has been reached. It is for this reason that we have undertaken a similar study but with more advanced equipment. MATERIALS AND METHODS: The Dermatop system analyses the relief of Silflo negative prints of the skin surface. It is based on the projection of interference fringes and phase shift and provides surface parameters and not profiles. In addition, the Toposurf software enables image processing and the precise and automatic calculation of the topography parameters (roughness, developed surface area and peak-trough amplitude) and anisotropy (level of anisotropy and furrow density). These parameters were studied on the forearm and temple of 40 men and 40 women evenly distributed into two groups: the first including subjects aged 25-35 years and the second 50-65 years. RESULTS: Roughness of both sites increases with age, independent of sex, but to a lesser extent in women than in men. The developed surface area and the peak-trough amplitude increase significantly with age irrespective of the site and the sex. The level of anisotropy increases with age, in both men and women, on the forearm and the temple, the site more exposed to light being more affected. The density of the furrows decreases with age in both sexes and both sites but with a greater increase for the temple, which is more exposed to solar ageing. CONCLUSION: The study of these new parameters will allow objective evaluation of the action of topical dermatological and cosmetic treatment, and new techniques in plastic surgery (e.g. laser resurfacing), and will enable the accurate follow-up of certain pathologies.

Radiation-induced skin fibrosis after treatment of breast cancer: profilometric analysis.

BACKGROUND/AIM: Treatment of breast cancer involves an association of conservative surgery and radiotherapy. This implies various cutaneous complications, well known for their clinical and histological aspects. Little data are available concerning modifications of the cutaneous microrelief after radiotherapy. We have done a profilometric analysis of the skin of breast cancer patients treated with surgery and radiotherapy. The results obtained on the irradiated breast have been compared with the ones of the controlateral normal breast. METHODS: Twenty women, 43-55 year old were enrolled in the study 6-16 months after the end of a treatment associating conservative surgery and radiotherapy for breast cancer. Imprints using a silicone rubber material were performed over symmetrical areas of the treated breast and the controlateral one. All measures were performed over the upper-medial quadrant of each breast. The imprints are then blindly analysed using an image analyser. The following parameters were measured: RA (average roughness of the skin), RZ (average of the furrows depth), RS (residual length), Rn (number of furrows) and AR (space between the furrows). RESULTS: The comparison of the imprints shows important modifications of the microrelief after irradiation. We observe a slight increase of the skin roughness (RA: 26, 39 +/- 2, 58 versus 21, 84 +/- 1, 59), a significantly increase of the furrows depth (RZ: 121, 66 +/- 10, 46 versus 101, 26 +/- 6, 99) along with an increase of the residual length (RS: 580, 60 +/- 60, 60 versus 450, 46 +/- 48, 43). The number of furrows has not significantly decreased but the space between the furrows has increased on the irradiated breast. CONCLUSION: This study shows a breakdown effect of irradiation on the skin in correlation with the fibrosis inducing by ionising radiation. The imprints modifications are clearly different from those usually observed in the ageing process. Our results can be a basis for studying the effects of treatments on cutaneous complications linked to the radiation-induced fibrosis.

Treatment of wrinkles with the nonablative 1,320-nm Nd:YAG laser.

Ablative laser resurfacing with the CO2 and Er:YAG lasers has become a well-accepted and well-reported modality for skin rejuvenation of photoaged and photodamaged skin. However, the side effects associated with these lasers, such as exudation and crusting followed by prolonged erythema, are often socially disturbing for the patient. A nonablative 1,320-nm pulsed Nd:YAG system has been developed that controls dermal collagen damage while preserving the epidermis. Thirteen patients are presented on whom periocular wrinkle treatment was carried out during two sessions 1 month apart. Side effects were minimal. Histology showed improvement in the previously typical sun-damaged dermis. However, although physician assessment noted a trend toward macroscopic improvement, almost all patients failed to see any improvement. The authors conclude that further studies of the ideal parameters are required before the 1,320-nm Nd:YAG laser can be indicated successfully in stand-alone, nonablative wrinkle removal. In addition, patients should be selected carefully, and a complementary minimally aggressive technique should be used to restore a youthful appearance to the epidermis.

Nonablative remodeling: clinical, histologic, ultrasound imaging, and profilometric evaluation of a 1540 nm Er:glass laser.

BACKGROUND: Nonablative remodeling has been recently proposed as an alternative to CO2 and Er:YAG resurfacing. OBJECTIVE: To evaluate the efficacy and safety of a 1540 nm Er:glass laser with contact cooling in nonablative skin remodeling, focused on perioral and periorbital rhytides. METHODS: Sixty patients (mean age 47 years), Fitzpatrick skin types I-IV were treated four times over 6-week intervals. Patients were evaluated using digital photographs, histology, ultrasound imaging, and profilometry with silicone imprints in order to quantitate the degree of clinical improvement. RESULTS: All subjects reported subjective improvement in the quality and visual aspect of their skin. This was confirmed by a 40.2% reduction of anisotropy (P <.001) 6 weeks after the fourth treatment. Ultrasound imaging demonstrated a 17% increase of dermis thickness (P <.005). Biopsy specimens showed evidence of new collagen formation. CONCLUSION: This study has clearly demonstrated that irradiation with 1540 nm Er:glass laser can lead to new collagen formation, dermis thickening, reduction of anisotropy of the skin, and clinical improvements. The lack of adverse effects confirmed that this 1540 nm laser emitting in a pulsed mode coupled with an efficient cooling system is safe.

Skin topography measurement by interference fringe projection: a technical validation.

BACKGROUND/AIMS: The quantitative analysis of skin topography is frequently used in cosmetology to evaluate the efficacy of hydrating or anti-wrinkle creams (micro-topography studies) or creams for slimming or to alleviate stretch marks (macro-topography studies). Numerous methods involving the three-dimensional (3-D) reconstruction of the topography from silicone replicas have been developed. Some of the main techniques applied include optical profilometry based on the reflection of oblique lighting or on transparency, and profilometry by laser focusing or triangulation. METHODS: We chose to test the Dermatop system developed by Eotech Co., which is based on interference fringe projection profilometry associated with the Toposurf surface processing software. Owing to the system's principle of operation, we first ran three experiments to evaluate the influence of ambient lighting on the 3-D reconstruction and the surface roughness parameters, the influence of the calibration device built into the acquisition system and the influence of calibration in terms of ambient lighting correction. We then evaluated the accuracy, the repeatability and the reproducibility of the measurements provided by the system from known metal topographic standards and skin replicas. RESULTS: It was seen that external lighting can cause variations in the calculation of parameters SPa, SPt and SPtm which can reach error levels of about 5% if the operator does not almost systematically calibrate the apparatus between each measurement. These three experiments enabled us to standardise the protocol for the acquisition of 3-D information, in order to minimise the lighting problems and yet respect the requirements for routine studies. The correlation coefficient between the theoretical values and the mean of experimental values was 0.9955 for parameter SPa and 0.9983 for parameter SPtm. Repeatability presented variations of under 4%, irrespective of the parameters, and reproducibility of under 6%. CONCLUSIONS: The technique provides very satisfactory results from the point of view of accuracy, repeatability and reproducibility. It is an excellent compromise between cost, accuracy and the time required.

Skin ageing: changes of physical properties of human skin in vivo.

We have investigated in vivo the change with age of various parameters that describe the physical properties of skin. The parameters were derived from pressure/displacement curves obtained by applying reduced pressure to a small area of skin and measuring the resulting displacement by 20 MHz scan echography. By fitting the pressure/displacement curves to a theoretical model, the following skin parameters were obtained: E, Young's modulus or stiffness (in Pascals); sigma(0), the initial stress (in Pascals); and the unrestored energy ratio (UER), an index related to cutaneous non-elasticity. These parameters, which are used in mechanics to define the intrinsic physical characteristics of materials, were measured for the first time on volar forearm skin of 206 male and female subjects, aged between 6 months and 90 years. The results showed that skin thickness increases until maturity and decreases for women over 50-60 years old, Young's modulus E increases linearly with age, and ageing is divided into two phases for natural stress, sigma(0) and the non-elasticity index UER. Natural stress sigma(0) increases until maturity and then rapidly decreases. The non-elasticity index decreases until puberty and steadily increases after puberty. This new procedure provides a simple quantitative assessment of the physical properties of the skin, revealing that the skin becomes thinner, stiffer, less tense and elastic with ageing.