RESUMO
Rapid detection of pathogens and analytes at the point of care offers an opportunity for prompt patient management and public health control. This paper reports an open microfluidic platform coupled with active whispering gallery mode (WGM) microsphere resonators for the rapid detection of influenza viruses. The WGM microsphere resonators, precoated with influenza A polyclonal antibodies, are mechanically trapped in the open micropillar array, where the evaporation-driven flow continuously transports a small volume (â¼µL) of sample to the resonators without auxiliaries. Selective chemical modification of the pillar array changes surface wettability and flow pattern, which enhances the detection sensitivity of the WGM resonator-based virus sensor. The optofluidic sensing platform is able to specifically detect influenza A viruses within 15 min using a few microliters of sample and displays a linear response to different virus concentrations.
Assuntos
Técnicas Biossensoriais , Humanos , MicroesferasRESUMO
Thin films of BaFCl:Sm nanocrystals prepared using a polymer binder were used to create fluorescence images. The phosphor films were exposed to a UV-C mercury lamp light source via chromium-coated quartz greyscale masks to create 4 µm resolution greyscale fluorescence images. The mechanism relies on the highly efficient conversion of Sm3+ to Sm2+ ions upon exposure to UV-C light which displays a large linear dynamic range. The red fluorescence around 688 nm of the Sm2+ is then read-out using blue-violet illumination under a laser scanning confocal microscope. The greyscale images with 16 greyscale levels had a resolution equivalent to â¼125 line pairs per mm or â¼6400 dpi. Improvements in the resolution would be possible using collimated UV-C laser exposure of the film or the use of higher resolution photomasks. Ultra-high resolution binary fluorescence images were also created with resolutions down to 2 µm (â¼250 line pairs per mm, â¼12 700 dpi). Downstream applications of the technology could include tailored covert or overt anti-counterfeiting labelling.
RESUMO
Metal-organic frameworks (MOFs) with ratiometric sensing properties are desirable for many applications due to their intrinsic self-calibration. We report the re-assessment of the sensing properties of a MOF, originally reported as containing europium(III) and 2-hydroxyterephtalic acid, and having fluorescent ratiometric iron(III) sensing properties. Synchrotron single-crystal X-ray diffraction and proton nuclear magnetic resonance (1H NMR) spectroscopy revealed that the MOF is composed of 2-methoxyterephthalate, not 2-hydroxyterephthalate as originally reported. We found that the MOF exhibits a sensor turn-off response towards Fe3+ ion concentrations in the range 0.5-3.7 ppm (band 425 nm), and a turn-on response towards a decrease of pH from 5.4 to 3.0 (band 375 nm), both resulting from the addition of acidic Fe3+ salt solution to a MOF suspension. Thus, the ratiometric sensing properties and the originally proposed mechanism no longer apply; our work reveals a dynamic quenching mechanism for the fluorescence turn-off response due to the presence of Fe3+ ions, and a ligand protonation mechanism for the turn-on response to a decrease in pH. Our work highlights the importance of a thorough investigation of the structure of any newly synthesized MOF, and, in the case of potential sensors, their selectivity and any environmental effects on their sensing behavior.
Assuntos
Estruturas Metalorgânicas , Európio/química , Compostos Férricos , Concentração de Íons de Hidrogênio , Íons , Estruturas Metalorgânicas/químicaRESUMO
The rapid development of optofluidic technologies in recent years has seen the need for sensing platforms with ease-of-use, simple sample manipulation, and high performance and sensitivity. Herein, an integrated optofluidic sensor consisting of a pillar array-based open microfluidic chip and caged dye-doped whispering gallery mode microspheres is demonstrated and shown to have potential for simple real-time monitoring of liquids. The open microfluidic chip allows for the wicking of a thin film of liquid across an open surface with subsequent evaporation-driven flow enabling continuous passive flow for sampling. The active dye-doped whispering gallery mode microspheres placed between pillars, avoid the use of cumbersome fibre tapers to couple light to the resonators as is required for passive microspheres. The performance of this integrated sensor is demonstrated using glucose solutions (0.05-0.3 g/mL) and the sensor response is shown to be dynamic and reversible. The sensor achieves a refractive index sensitivity of ~40 nm/RIU, with Q-factors of ~5 × 103 indicating a detection limit of ~3 × 10-3 RIU (~20 mg/mL glucose). Further enhancement of the detection limit is expected by increasing the microsphere Q-factor using high-index materials for the resonators, or alternatively, inducing lasing. The integrated sensors are expected to have significant potential for a host of downstream applications, particularly relating to point-of-care diagnostics.
Assuntos
Microfluídica , Refratometria , Ação Capilar , Glucose , MicroesferasRESUMO
Coupling characteristics between a single mode fiber (SMF) and a waveguide embedded in a glass chip via a graded index fiber (GIF) tip are investigated at a wavelength of 976 nm. The GIF tips comprise a coreless fiber section and a GIF section. A depressed cladding waveguide in a ZBLAN glass chip with a core diameter of 35 µm is coupled with GIF tips that have a range of coreless fiber and GIF lengths. An experimental coupling efficiency as high as 88% is obtained while a numerical simulation predicts 92.9% for the same GIF tip configuration. Since it is measured in the presence of Fresnel reflection, it can be further improved by anti-reflection coating. Additionally, it is demonstrated that a gap can be introduced between the chip waveguide and the GIF tip while maintaining the high coupling efficiency, thus allowing a thin planar optical component to be inserted. The results presented here will enable miniaturization and simplification of photonic chips with integrated waveguides by replacing bulk coupling lenses with integrated optical fibers.
RESUMO
Graded-index optical fiber probes suitable for focusing or collimating the output of an optical fiber at a wavelength of 1.3 µm have become an enabling technology in optical coherence tomography imaging applications for in vivo bioimaging. Such fiber tips however remain uncommon in other photonics applications. This paper provides the first numerical study of graded-index fiber tips covering a broad range of wavelengths spanning from the UV to short-infrared. The wavelength dependency and the influence of probe geometry on performance characteristics such as far-field divergence angle, spot size and working distance are analyzed. The paper yields easily accessible design guidelines for the fabrication of collimating or focusing fiber tips. Fiber collimators have considerable potential for use in free-space systems and could benefit a range of devices such as variable attenuators, dynamic wavelength equalisers and large 3D optical cross-connect switches, whereas focusing fiber tips have applications in high-resolution imaging.
RESUMO
To support the growing landscape of near to mid-IR laser applications we demonstrate a range of low propagation loss femtosecond laser (FSL) written waveguides (WGs) that have achieved guided-mode laser operation in a rare earth (RE) doped lead-germanate glass. The WGs are fabricated in both the athermal and thermal FSL writing regimes using three different pulse repetition frequencies (PRF): 100 kHz (athermal); 1 MHz; and 5 MHz (thermal). The lasing capability of Yb3+ doped lead-germanate waveguides is verified in the near-IR. The refractive index contrast (∆n) for 100 kHz WGs is ~ 1 × 10-4, while for 5 MHz, ∆n increases to ~ 5 × 10-4. The WGs in the thermal regime are less effected by self-focusing and are larger in dimensions with reduced propagation losses. For the 1 MHz repetition rate thermal writing regime we report a low propagation loss WG (0.2 dB/cm) and demonstrate laser operation with slope efficiencies of up to ~ 28%.
RESUMO
This paper describes the design and characterization of miniaturized optofluidic devices for sensing based on integrating collimating optical fibers with custom microfluidic chips. The use of collimating graded-index fiber (GIF) tips allows for effective fiber-channel-fiber interfaces to be realized when compared with using highly-divergent standard single-mode fiber (SMF). The reduction in both beam divergence and insertion losses for the GIF configuration compared with SMF was characterized for a 10.0 mm channel. Absorption spectroscopy was demonstrated on chip for the measurement of red color dye (Ponceau 4R), and the detection of thiocyanate in water and artificial human saliva. The proposed optofluidic setup allows for absorption spectroscopy measurements to be performed with only 200 µL of solution which is an order of magnitude smaller than for standard cuvettes but provides a comparable sensitivity. The approach could be integrated into a lab-on-a-chip system that is compact and does not require free-space optics to perform absorption spectroscopy.
RESUMO
Femtosecond laser inscribed fiber Bragg gratings in pure-silica suspended-core optical fibers have previously been demonstrated as a promising platform for high temperature sensing. However, the density of gratings that could be written on a single fiber was limited by undesired reflections associated with higher order modes in these high numerical aperture fibers. This resulted in a complex, broadband reflection spectrum with limited multiplexing capability. In this work we utilize modifications to the fine structure of the suspended core optical fibers to fine tune the relative confinement loss of the optical fiber modes, thus reducing the contribution from such higher order modes. The effects of these changes on mode propagation are modeled, giving a range of fibers with different confinement loss properties which can be tailored to the specific length scale of a desired application. We achieve single-peak reflections from individual fiber Bragg gratings, significantly improving performance for multipoint sensing and demonstrate this technique by writing 20 gratings onto a single fiber.
RESUMO
The evanescent fields along multimode fibers are usually relatively weak. To enhance the sensitivity of the resulting sensors, skew rays have been exploited for their larger number of total internal reflections and their more comprehensive spread over the fiber surface. The uniform distribution of light-matter interactions across the fiber surface facilitates high sensitivity through an increased interaction area, while mitigating the risk of laser-induced coating-material damage and photobleaching. Power-dependent measurements are less susceptible to temperature effects than interferometric techniques, and place loose requirements on the laser source. This review highlights the key developments in this area, while discussing the benefits, challenges as well as future development.
RESUMO
BACKGROUND: O-negative red blood cells (ON-RBC) are a precious resource and the international blood banking community has become increasingly concerned with its inappropriate utilization. AABB recently made several recommendations to address the issue. Solutions must be multifaceted and involve donor centers, blood banks, and clinical departments. From the perspective of a hospital blood bank, it is difficult to rely solely on increased donor recruitment and ubiquitous blood typing of the entire in-patient population. We therefore focused on interventions within the blood bank to optimize inventory and policies to ensure appropriate ON-RBC utilization. STUDY DESIGN AND METHODS: Transfusion data over one year was examined for the rate of out-of-group/inappropriate ON-RBC. Furthermore, we assessed whether that rate was related to product life on the day of transfusion. We also examined our stock inventory levels and how excess inventory can contribute to inappropriate ON-RBC usage. RESULTS: The ON-RBC inventory level was decreased in order to reduce the rate of inappropriate transfusions while maintaining a safe level for optimal patient care. Compared to baseline, our intervention caused ON-RBCs to be transfused earlier in their shelf-life (9.27 vs. 11.15 days from expiration [DFE], p = 0.0012). This reduced the overall rate of inappropriate ON-RBC transfusions (67% vs. 54%, p = 0.0035), approximating 185 units of ON-RBC saved over the course of 6 months. CONCLUSIONS: A data-driven approach to optimize stock inventory levels is widely applicable; it can be adopted by numerous institutions to improve utilization and establish a benchmark for the broader blood banking community.
Assuntos
Armazenamento de Sangue/métodos , Eritrócitos/imunologia , Inventários Hospitalares , Sistema ABO de Grupos Sanguíneos , Estabilidade de Medicamentos , Humanos , Revisão da Utilização de Recursos de SaúdeRESUMO
A stronger absorption of pump/probe light is desirable for maximizing the sensitivity to enable accurate measurements of trace chemical elements. We introduce a new sensing technique built on light-sheet excitation of skew rays in a multimode fiber with an additional enhancement of localized surface plasmon resonance (LSPR) and its evanescent-field hotspots between gold nanospheres on the coated fiber. A skewed light-sheet (i.e., a thin plane of light) can exploit the optimum ray group, producing enhanced and uniform interactions between light and matter for higher absorption/sensitivity and higher power threshold. The heightened evanescent field couples to the localized surface plasmon resonant modes to attain even greater sensitivity. We compared this excitation method with the previously demonstrated light-sheet skew ray-based sensor without LSPR and observed an enhancement in normalized attenuation of pump light up to seven orders of magnitude for low-concentration rhodamine B. The improvement in the normalized detection limit is almost three orders of magnitude. This new sensing technique uses a functionalized fiber rather than pairing a passive fiber with added functional particles in the analyte, which offers better area-selectivity. The potentially low-cost chemical sensors can be used on a range of sensing mechanisms such as pump/probe light absorption.
Assuntos
Técnicas Biossensoriais/métodos , Ressonância de Plasmônio de Superfície/métodos , HumanosRESUMO
A guided-wave chip laser operating in a single longitudinal mode at 2860 nm is presented. The cavity was set in the Littman-Metcalf configuration to achieve single-frequency operation with a side-mode suppression ratio above 33 dB. The chip laser's 2 MHz linewidth on a 10 ms scale was found to be limited by mechanical fluctuations, but its Lorentzian contribution was estimated to be lower than 1 Hz using a heterodyne technique. This demonstration incorporates a high coherence source with the simplicity provided by the compactness of chip lasers.
RESUMO
Absorption lines of methane in the 2ν3 band centered at 1650 nm were measured with a free-running mode-locked dual-comb laser based on a single erbium-doped glass chip. The laser's spectra were broadened up to 1670 nm using amplifiers and highly nonlinear fiber. A comb was used to interrogate the complex transmission spectrum of a methane-filled gas cell with an optical point spacing of 968 MHz and an interferogram (IGM) rate of 27 kHz to yield absorption lines of the R and Q branches. A 1.28 s sequence of IGMs was measured and phase-corrected using a self-sufficient correction algorithm seeded only by the IGMs. The associated transmission spectrum was then compared to HITRAN yielding residuals limited by photodetector nonlinearity.
RESUMO
There is a deficiency of low-loss microstructured waveguides that can be fabricated with a single laser-pass to minimize stress build-up, which can enable enhanced functionality and higher compactness for integrated optical devices. We demonstrate, for the first time, a series of multi-ring claddings each with a pair of cores in BK7 glass. Each waveguide was fabricated using only a single laser-pass at 1 MHz pulse repetition rate, 5 mm/s translation speed, 250 fs pulse width, over a set of pulse energies. We obtained the lowest-reported propagation loss of 0.062 dB/cm, measured at 1155 nm wavelength from the waveguide written with 340 nJ pulse energy. The maximum observed numerical aperture is 0.020, measured at 1155 nm wavelength from the waveguide written with 620 nJ pulse energy. Such waveguides could be incorporated in integrated Raman laser platforms for biomedical applications.
RESUMO
We present a novel approach to study continuous-wave mode-locking in a waveguide laser in the presence of a gain profile with complex features. We introduce a new simulation approach where we separate the role of gain, nonlinearity, dispersion and saturable absorption elements to provide a better understanding of the interplay between these elements. In particular, we use the simulation to explain synchronised dual-wavelength mode-locking. The results show that despite the existence of dispersion which tends to form separate pulse trains in the laser cavity, the saturable absorber plays a critical role in keeping the different wavelength components synchronised. This work, for the first time, provides insight into existing experimental results. It also demonstrates new methods for studying lasers, especially mode-locking laser, with short laser cavities.
RESUMO
BACKGROUND: The ordering process at Stanford Health Care involved twice-daily shipments predicated upon current stock levels from the blood center to the hospital transfusion service. Manual census determination is time consuming and error prone. We aimed to enhance inventory management by developing an informatics platform to streamline the ordering process and reallocate staff productivity. STUDY DESIGN AND METHODS: The general inventory accounts for more than 50 product categories based on characteristics including component, blood type, irradiation status, and cytomegalovirus serology status. Over a 5-month calibration period, inventory levels were determined algorithmically and electronically. An in-house software program was created to determine inventory levels, optimize the electronic ordering process, and reduce labor time. A 3-month pilot period was implemented using this program. RESULTS: This system showed noninferiority while saving labor time. The average weekly transfused:stocked ratios for cryoprecipitate, plasma, and red blood cells, respectively, were 1.03, 1.21, and 1.48 before the pilot period, compared with 0.88, 1.17, and 1.40 during (p = 0.28). There were 27 (before) and 31 (during) average STAT units ordered per week (p = 0.86). The number of monthly wasted products due to expiration was 226 (before) and 196 (during) units, respectively (p = 0.28). An estimated 7 hours per week of technologist time was reallocated to other tasks. CONCLUSION: An in-house electronic ordering system can enhance information fidelity, reallocate and optimize valuable staff productivity, and further standardize ordering. This system showed noninferiority to the labor-intensive manual system while freeing up over 360 hours of staff time per year.
Assuntos
Equipamentos e Provisões Hospitalares/estatística & dados numéricos , Inventários Hospitalares/métodos , Informática Médica/métodos , Bancos de Sangue/estatística & dados numéricosRESUMO
We characterize the frequency noise performance of a free-running dual-comb source based on an erbium-doped glass chip running two adjacent mode-locked waveguide lasers. This compact laser platform, contained only in a 1.2 L volume, rejects common-mode environmental noise by 20 dB thanks to the proximity of the two laser cavities. Furthermore, it displays a remarkably low mutual frequency noise floor around 10 Hz2/Hz, which is enabled by its large-mode-area waveguides and low Kerr nonlinearity. As a result, it reaches a free-running mutual coherence time of 1 s since mode-resolved dual-comb spectra are generated even on this time scale. This design greatly simplifies dual-comb interferometers by enabling mode-resolved measurements without any phase lock.
RESUMO
Ultrafast laser inscribed waveguide lasers can lead to highly efficient and compact optical devices. This Letter reports an average lasing efficiency of 65%±2.5% from a multi-waveguide 2.5 mol. % ytterbium-doped ZrF4-BaF2-LaF3-AlF3-NaF (Yb:ZBLAN) chip in an extended-cavity configuration. A maximum output power of 750 mW with a lasing efficiency of 68% is also achieved. A monolithic end-coupled configuration reached a maximum output power of 784 mW with a lasing efficiency of 70%. The lasing wavelength is tuned from 1001 to 1045 nm in a Littrow configured cavity. A beam propagation factor of the lowest-order transverse-mode output was routinely achieved with an M2 of 1.15.