Analysis of Polyvinylidene Fluoride Membranes Fabricated for Membrane Distillation.

The optimization of the properties for MD membranes is challenging due to the trade-off between water productivity and wetting tendency. Herein, this study presents a novel methodology to examine the properties of MD membranes. Seven polyvinylidene fluoride (PVDF) membranes were synthesized under different conditions by the phase inversion method and characterized to measure flux, rejection, contact angle (CA), liquid entry pressure (LEP), and pore sizes. Then, water vapor permeability (Bw), salt leakage ratio (Lw), and fiber radius (Rf) were calculated for the in-depth analysis. Results showed that the water vapor permeability and salt leakage ratio of the prepared membranes ranged from 7.76 × 10-8 s/m to 20.19 × 10-8 s/m and from 0.0020 to 0.0151, respectively. The Rf calculated using the Purcell model was in the range from 0.598 µm to 1.690 µm. Since the Rf was relatively small, the prepared membranes can have high LEP (more than 1.13 bar) even at low CA (less than 90.8°). The trade-off relations between the water vapor permeability and the other properties could be confirmed from the results of the prepared membranes. Based on these results, the properties of an efficient MD membrane were suggested as a guideline for the membrane development.

Retardation of wetting for membrane distillation by adjusting major components of seawater.

Wetting by fouling is phenomenon specific to membrane distillation (MD) and are regarded as challenges to the seawater membrane distillation (SWMD) process. To understand fouling and wetting, the influence of Mg and Sr crystals, which can potentially cause scaling, as well as Ca crystals deposited on the membrane surface were investigated. Mg(OH)2 and CaSO4 had significant impact on fouling and wetting. Even if CaCO3 and SrSO4 had no effects on fouling and wetting as single salts, CaCO3 and CaSO4 were dominant in synthetic seawater without Mg(OH)2. However, the occurrence of Mg(OH)2 scales became a cause for concern if Ca ion was removed from seawater for the prevention of fouling and wetting. Therefore, Mg as well as Ca should be removed for proper fouling and wetting control. NaOH/Na2CO3 softening was used for the removal of Ca and Mg ions. In addition, based on the inhibition effects of Mg ions on Ca scales, a new pretreatment method involving the injection of MgCl2 to increase the Mg /Ca ratio was examined.

Process stability and comparative rDNA/rRNA community analyses in an anaerobic membrane bioreactor with silicon carbide ceramic membrane applications.

This study evaluated the feasibility of using a silicon carbide (SiC) anaerobic ceramic membrane bioreactor (AnCMBR) to co-manage domestic wastewater (DWW) and food waste recycling wastewater (FRW). A pilot-scale SiC-AnCMBR was put into operation for 140 days under two different organic loading rates (OLRs): 5 kg COD m-3 d-1 (OLR 5) and 3 kg COD m-3 d-1 (OLR 3). The organic removal efficiency was 93.5 ±â€¯3.7% over the operational period. Methane production increased significantly after sludge re-seeding at OLR 3. rDNA and rRNA microbial results showed that the active archaeal community was affected by sludge re-seeding, whereas the active bacterial community was not, indicating that a shift in the active archaeal community was responsible for the increased methane production. Our results thus suggest that SiC-AnCMBRs are a promising option for co-managing DWW and FRW.

Chlorination caused a shift in marine biofilm niches on microfiltration/ultrafiltration and reverse osmosis membranes and UV irradiation effectively inactivated a chlorine-resistant bacterium.

The effect of chlorine disinfection on marine biofilm populations and communities formed on membrane surfaces was investigated under two feedwater conditions: raw seawater and deep bed filtration-treated seawater. As a result of chlorination, the structure of the biofilm community on the microfiltration/ultrafiltration and reverse osmosis membrane coupons shifted significantly at the genus level. However, the total bacterial population was not reduced under the two feedwater conditions. This failure to control the biofilm was attributed to the adaptation and survival of selected bacteria under chlorine stress. Phaeobacter caeruleus, isolated from the biofilm, was examined as a representative chlorine-resistant biofilm-forming bacterium. The number of viable P. caeruleus was significantly reduced (as much as 99.8%) after ultraviolet (UV) disinfection. The results indicated that additional disinfection by UV irradiation can inactivate chlorine-resistant bacteria. Therefore, tandem chlorination-UV disinfection may enhance the efficiency of biofouling control in seawater reverse osmosis processes. The synergistic effects of tandem chlorination-UV irradiation on the marine biofilm community should be investigated in future studies.

Negligible seeding source effect on the final ANAMMOX community under steady and high nitrogen loading rate after enrichment using poly(vinyl alcohol) gel carriers.

This study investigated the effect of seeding source on the mature anaerobic ammonia oxidation (ANAMMOX) bacterial community niche in continuous poly(vinyl alcohol) (PVA) gel systems operated under high nitrogen loading rate (NLR) condition. Four identical column reactors packed with PVA gels were operated for 182 d using different seeding sources which had distinct community structures. The ANAMMOX reaction was achieved in all the bioreactors with comparable total and ANAMMOX bacterial 16S rRNA gene quantities. The bacterial community structure of the bioreactors became similar during operation; some major bacteria were commonly found. Interestingly, one ANAMMOX species, "Candidatus Brocadia sinica", was conclusively predominant in all the bioreactors, even though different seeding sludges were used as inoculum source, possibly due to the unique physiological characteristics of "Ca. Brocadia sinica" and the operating conditions (i.e., PVA gel-based continuous system and 1.0 kg-N/(m3·d) of NLR). The results clearly suggest that high NLR condition is a more significant factor determining the final ANAMMOX community niche than is the type of seeding source.

Effective seeding strategy using flat type poly (vinyl alcohol) cryogel for anammox enrichment.

In this study, anammox enrichment reactors were operated using flat type poly (vinyl alcohol) cryogel (cryoPVAG) with precultured anammox bacteria (PAB) and activated sludge (AS) from an anoxic tack of the A2O process to evaluate the effect of different seeding sources on anammox enrichment. In addition, cryoPVAGs with different thicknesses (1, 2, and 3 mm) were used to investigate the effects of the thickness on anammox enrichment. The regression analysis with a modified Gompertz model showed that the start-up period of the anammox enrichment using PAB inoculum was approximately 14 days earlier than that of AS inoculum at a nitrogen loading rate of approximately 1 kg-N m-3 day-1. Substrate diffusion was limited in 3-mm cryoPVAG with respect to trend in nitrogen removal rate. Quantitative PCR analysis indicated that in the initial phase, the 16S rRNA gene copy numbers of anammox microorganism in cryoPVAG were significantly different according to the seeding source, but finally converged to a similar level after anammox enrichment. The anammox reaction was initially promoted by cryoPVAG. Next, anammox biomass detached from cryoPVAG and enriched in the bulk phase to maximize NRR. Illumina MiSeq sequencing revealed that Candidatus Brocadia sinica led to the active anammox reaction, and its relative abundance decreased with increasing gel thickness.

Effects of the ammonium loading rate on nitrite-oxidizing activity during nitrification at a high dose of inorganic carbon.

In this study, the effects of the ammonium loading rate (ALR) and inorganic carbon loading rate (ILR) on the nitrification performance and composition of a nitrifying bacterial community were investigated in a moving bed biofilm reactor, using poly(vinyl alcohol) (PVA) sponge cubes as a supporting carrier. Between the two ALRs of 0.36 and 2.16 kg-N m-1 d-1, stable partial nitritation was achieved at the higher ALR. Inorganic carbon was dosed at high levels: 33.1, 22.0, 16.4, 11.0, and 5.4 times the theoretical amount. Nonetheless, nitrification efficiency was not affected by the ILR at the two ALRs. Quantitative PCR analysis of ammonia- and nitrite-oxidizing bacteria revealed that ALR is an important determinant of partial nitritation by accumulating ammonia-oxidizing bacteria in the nitrification system. In comparison, two nitrite-oxidizing bacterial genera (Nitrobacter and Nitrospira) showed almost the same relative abundance at various ALRs and ILRs. Terminal restriction fragment length polymorphism targeting the gene of ammonia monooxygenase subunit A revealed that Nitrosomonas europaea dominated under all conditions.

Effects of changes in temperature on treatment performance and energy recovery at mainstream anaerobic ceramic membrane bioreactor for food waste recycling wastewater treatment.

An anaerobic ceramic membrane bioreactor (AnCMBR) has been attracted as an alternative technology to co-manage various organic substrates. This AnCMBR study investigated process performance and microbial community structure at decreasing temperatures to evaluate the potential of AnCMBR treatment for co-managing domestic wastewater (DWW) and food waste-recycling wastewater (FRW). As a result, the water flux (≥6.9 LMH) and organic removal efficiency (≥98.0%) were maintained above 25 °C. The trend of methane production in the AnCMBR was similar except for at 15 °C. At 15 °C, the archaeal community structure did not shifted, whereas the bacterial community structure was changed. Various major archaeal species were identified as the mesophilic methanogens which unable to grow at 15 °C. Our results suggest that the AnCMBR can be applied to co-manage DWW and FRW above 20 °C. Future improvements including psychrophilic methanogen inoculation and process optimization would make co-manage DWW and FRW at lower temperature climates.

Effect of engineered environment on microbial community structure in biofilter and biofilm on reverse osmosis membrane.

Four dual media filters (DMFs) were operated in a biofiltration mode with different engineered environments (DMF I and II: coagulation with/without acidification and DMF III and IV: without/with chlorination). Designed biofilm enrichment reactors (BERs) containing the removable reverse osmosis (RO) coupons, were connected at the end of the DMFs in parallel to analyze the biofilm on the RO membrane by DMF effluents. Filtration performances were evaluated in terms of dissolved organic carbon (DOC) and assimilable organic carbon (AOC). Organic foulants on the RO membrane were also quantified and fractionized. The bacterial community structures in liquid (seawater and effluent) and biofilm (DMF and RO) samples were analyzed using 454-pyrosequencing. The DMF IV fed with the chlorinated seawater demonstrated the highest reductions of DOC including LMW-N as well as AOC among the other DMFs. The DMF IV was also effective in reducing organic foulants on the RO membrane surface. The bacterial community structure was grouped according to the sample phase (i.e., liquid and biofilm samples), sampling location (i.e., DMF and RO samples), and chlorination (chlorinated and non-chlorinated samples). In particular, the biofilm community in the DMF IV differed from the other DMF treatments, suggesting that chlorination exerted as stronger selective pressure than pH adjustment or coagulation on the biofilm community. In the DMF IV, several chemoorganotrophic chlorine-resistant biofilm-forming bacteria such as Hyphomonas, Erythrobacter, and Sphingomonas were predominant, and they may enhance organic carbon degradation efficiency. Diverse halophilic or halotolerant organic degraders were also found in other DMFs (i.e., DMF I, II, and III). Various kinds of dominant biofilm-forming bacteria were also investigated in RO membrane samples; the results provided possible candidates that cause biofouling when DMF process is applied as the pretreatment option for the RO process.

Comparison of inoculum sources for long-term process performance and fate of ANAMMOX bacteria niche in poly(vinyl alcohol)/sodium alginate gel beads.

The process performance and microbial niche of anaerobic ammonia oxidation (ANAMMOX) bacteria were compared in two identical bioreactors inoculated with different inoculum sources (i.e., pre-cultured ANAMMOX bacteria: PAB and activated sludge: AS) entrapped in poly(vinyl alcohol)/sodium alginate (PVA/SA) gel beads for a long-term period (i.e., 1.5 years). The start-up period with AS was longer than that with PAB; however, both bioreactors were successfully operated over the long-term with stable ANAMMOX activity. After long-term operation, the 16S rRNA gene concentration of ANAMMOX bacteria in both bioreactors was significantly increased, and thereby became comparable. In addition, Candidatus Jettenia sp. became the dominant ANAMMOX species in both bioreactors. Our results suggested that the ANAMMOX performance and microbial niche of ANAMMOX bacteria became nearly identical during long-term operation despite the use of different inoculum sources. Therefore, the use of PVA/SA gel beads entrapping AS appears to be a relevant option for constructing an ANAMMOX process in places where a full-scale ANAMMOX process has never been done previously.

Targeted removal of trichlorophenol in water by oleic acid-coated nanoscale palladium/zero-valent iron alginate beads.

A new material was developed and evaluated for the targeted removal of trichlorophenol (TCP) from among potential interferents which are known to degrade removal activity. To achieve TCP-targeted activity, an alginate bead containing nanoscale palladium/zero-valent iron (Pd/nZVI) was coated with a highly hydrophobic oleic acid layer. The new material (Pd/nZVI-A-O) preferentially sorbed TCP from a mixture of chlorinated phenols into the oleic acid cover layer and subsequently dechlorinated it to phenol. The removal efficacy of TCP by Pd/nZVI-A-O was not affected by co-existing organic substances such as Suwannee River humic acid (SRHA), whereas the material without the oleic acid layer (Pd/nZVI-A) became less effective with increasing SRHA concentration. The inorganic substances nitrate and phosphate significantly reduced the reactivity of Pd/nZVI-A, however, Pd/nZVI-A-O showed similar TCP removal efficacies regardless of the initial inorganic ion concentrations. The influence of bicarbonate on the TCP removal efficacies of both Pd/nZVI-A and Pd/nZVI-A-O was not significant. The findings from this study suggest that Pd/nZVI-A-O, with its targeted, constant reactivity for TCP, would be effective for treating this contaminant in surface water or groundwater containing various competitive substrates.

Assessment of bacterial community structure in nitrifying biofilm under inorganic carbon-sufficient and -limited conditions.

In this work, nitrification and changes in the composition of the total bacterial community under inorganic carbon (IC)-limited conditions, in a nitrifying moving bed biofilm reactor, was investigated. A culture-independent analysis of cloning and sequencing based on the 16S rRNA gene was applied to quantify the bacterial diversity and to determine bacterial taxonomic assignment. IC concentrations had significant effects on the stability of ammonia-oxidation as indicated by the reduction of the nitrogen conversion rate with high NH4(+)-N loadings. The predominance of Nitrosomonas europaea was maintained in spite of changes in the IC concentration. In contrast, heterotrophic bacterial species contributed to a high bacterial diversity, and to a dynamic shift in the bacterial community structure, under IC-limited conditions. In this study, individual functions of heterotrophic bacteria were estimated based on taxonomic information. Possible key roles of coexisting heterotrophic bacteria are the assimilation of organic compounds of extracellular polymeric substances produced by nitrifiers, and biofilm formation by providing a filamentous structure and aggregation properties.

Effect of anions and humic acid on the performance of nanoscale zero-valent iron particles coated with polyacrylic acid.

Effects of anions (NO3(-), HCO3(-), Cl(-), SO4(2-)) and humic acid on the reactivity and core/shell chemistries of polyacrylic acid-coated nanoscale zero-valent iron (PAA-NZVI) and inorganically modified NZVI (INORG-NZVI) particles were investigated. The reactivity tests under various ion concentrations (0.2-30mN) revealed the existence of a favorable molar ratio of anion/NZVI that increased the reactivity of NZVI particles. The presence of a relatively small amount of humic acid (0.5mgL(-1)) substantially decreased the INORG-NZVI reactivity by 76%, whereas the reactivity of PAA-NZVI decreased only by 12%. The XRD and TEM results supported the role of the PAA coating of PAA-NZVI in impeding the oxidation of the Fe(0) core by groundwater solutes. This protective role provided by the organic coating also resulted in a 2.3-fold increase in the trichloroethylene (TCE) reduction capacity of PAA-NZVI compared to that of INORG-NZVI in the presence of anions/humic acid. Ethylene and ethane were simultaneously produced as the major reduction products of TCE in both NZVI systems, suggesting that a hydrodechlorination occurred without the aid of metallic catalysts. The PAA coating, originally designed to improve the mobility of NZVI, enhanced TCE degradation performances of NZVI in the presence of anions and humic acid.

Effects of washing solution and drying condition on reactivity of nano-scale zero valent irons (nZVIs) synthesized by borohydride reduction.

Washing and drying processes are essential when synthesizing nano-scale zero valent irons (nZVIs) by borohydride reduction of iron salts in aqueous phase. However, effects of these processes on nZVI reactivity have not been investigated in detail, although different washing and drying conditions might alter surface characteristics of nZVIs and thus vary their reactivity towards reducible contaminants. In this study, effects of three washing solutions and drying conditions on the reactivity of nZVIs for nitrate were investigated. Washing with volatile solvents and drying under anaerobic condition decreased thickness of Fe-oxide layer on nZVIs and increased content of Fe(2+)-containing oxides in the layer, which enhanced nZVI reactivity toward nitrate. Volatile solvent washing could minimize the decrease in nZVI reactivity according to changing anaerobic drying condition to aerobic. Findings from this study suggest that application of washing with volatile solvents and drying under aerobic condition should be recommended as effective processes to obtain nZVIs with maximum reactivity at reasonable costs and efforts.

High-rate partial nitritation using porous poly(vinyl alcohol) sponge.

Poly(vinyl alcohol) (PVA) has been utilized as a support material for the immobilization of nitrifying bacteria without the comprehensive survey of partial nitritation. In the present study, the activities of nitrifiers and the maximum nitrogen conversion rate of partial nitritation with PVA sponge-cubes were specified according to different conditions. The selective enrichment of ammonia-oxidizing bacteria (AOB) on PVA sponge-cubes was achieved by the competition between AOB and nitrite-oxidizing bacteria for dissolved oxygen. The efficiency of ammonia oxidation was proportional to the concentration of HCO3 (-) with the molar ratio of HCO3 (-)-C/NH4 (+)-N = 1.91 and a half of the ratio was applied to the further experiments to ensure stable partial nitritation. The maximum nitrogen conversion rate of partial nitritation was dependent on the volume, not the size of sponge-cubes. The partial nitritation showed the superior rate performance of 3.09 kg N/m(3) day with the packing ratio of 32 % of 5 × 5 × 5 mm(3) PVA sponge-cubes.

Oxidation of bisphenol A by UV/S2O8(2-): comparison with UV/H2O2.

The UV/S2O8(2-) process was applied to decompose bisphenol A (BPA), which is a representative endocrine-disrupting chemical (EDC), and was comared with the UV/H2O2 process. The BPA degradation efficiency by UV/S2O8(2-) was increased by increasing S2O8(2-) concentration or decreasing BPA concentration. The presence of humic acid caused an inhibitory effect. The BPA oxidation rate by UV/S2O8(2-) was increased in the following order: neutral pH (pH(i) = 7) < acidic pH (pH(i) = 4) < basic pH (pH(i) = 10). The main oxidizing species in the UV/S2O8(2-) system was sulphate radical (SO4(-*)), whereas the main oxidizing species in the UV/H2O2 system was OH radical (OH*). Compared with UV/H2O2, the UV/S2O8(2-) process showed higher performance for not only BPA degradation but also its mineralization, which means that SO4(-*) is a more effective oxidant for BPA than the OH*. The results shown in this study imply that the SO4(-*) -based UV/S2O8(2-) process can be an excellent alternative process for the widely used UV/H2O2 process, with higher remediation performance.

Chemometrics in assessment of seasonal variation of water quality in fresh water systems.

The chemometric techniques were applied for evaluation of the seasonal variation of water qualities at 17 stations along a stretch of the Bagmati river of Nepal for 23 water quality parameters measured during 1999-2003. The application of discriminant analysis confirmed the classification of the water quality measurements into three seasons: pre-monsoon, monsoon, and post-monsoon affording 93.8% correct classification. Factor analysis and box-whisker plots facilitated to investigate the seasonal variation of water quality and the pattern of pollution sources. Application of FA revealed that the influence of water quality parameters changes from season to season. A parameter that is most important in contributing to water quality variation for one season may not be important for another season. Comparison of the discriminant analysis and factor analysis helped to identify the most important water quality parameters, as water temperature, DO, EC, COD, CL, Ca, alkalinity, PO(4)P, and TP, that are most important for seasonal variation and play a significant role in establishment of water quality control strategy.

Analyses of calcium carbonate scale deposition on four RO membranes under a seawater desalination condition.

Inorganic fouling is one of the critical operational issues in reverse osmosis membrane. Few researches investigated effects of membrane surface characteristics on inorganic fouling and on anti-scaling techniques although the fouling occurs on the membrane surface. The objective of this paper was to examine whether different characteristics of deposition of calcium carbonate solids would occur on four membranes having distinctive surface properties. A lab-scale cell reactor with a crossflow velocity was installed and two coupons were used for one type of membranes. Two feed waters were examined: concentrated synthetic seawater simulating a 30% recovery and a concentrate from a seawater RO plant in operation at Changwon, Korea. The amounts of solid deposition on the attached membranes were increased in all four membranes but the degree of deposition on each membrane was different. Various types of calcium carbonate solids were clearly detected by both XRD and SEM analyses. In general, a membrane with greater roughness and negative surface charge appeared to form more scales. This implied that membrane surface characteristics such as roughness and surface charge affected inorganic fouling, presumably by providing favourable sites for precipitation and enhancing attraction of species to the membrane surface.

Influence of membrane surface properties on the behavior of initial bacterial adhesion and biofilm development onto nanofiltration membranes.

In order to investigate biofouling problems, the fundamental behaviors of initial bacterial adhesion and biofilm development on four different nanofiltration (NF) membranes were evaluated using Pseudomonas aeruginosa PAO1 as a model bacterial strain. Initial cell adhesion was considerably higher on an aromatic polyamide-based NF membrane with a hydrophobic and rough surface, whereas cell aggregation on a polypiperazine-based NF membrane with a relatively hydrophilic and smooth surface was lower. Moreover, significant differences in the structural heterogeneity of the biofilms were observed among the four NF membranes. This study shows that the surface roughness and hydrophobicity of a membrane play an important role in determining initial cell adhesion, aggregation and favorable localization sites for colony formation. In addition, it was found that biofilm development was strongly influenced by the surface morphology of a membrane.

Assessment of spatial-temporal patterns of surface and ground water qualities and factors influencing management strategy of groundwater system in an urban river corridor of Nepal.

This study examined the spatial-temporal variations and factors influencing the management of groundwater along a section of the Bagmati river corridor in the Kathmandu valley (Nepal). The results showed that rural areas were less polluted than urban areas. In urban areas, the biochemical oxygen demand (BOD), total nitrogen (TN) and total phosphorus (TP) concentrations ranged from 8.41 to 29.74 mg/L, 6.7 to 128.96 mg/L and 0.06 to 1.5 mg/L, respectively. In rural areas, the BOD, TN and TP concentrations ranged from 0.78 to 18.25 mg/L, 4.8 to 11.56 mg/L and 0.07 to 0.65 mg/L, respectively. The level of organics was higher in the pre-monsoon season, while the level of nutrients was higher in post-monsoon season. A comparison of the groundwater and surface water in the upstream rural areas revealed that the TP concentration was higher in the groundwater than in the surface water, which was attributed to the sorption of phosphorus on iron, aluminum or calcium compounds contained in the surface water, which depends upon the temperature, pH and dissolved oxygen. In urban areas, a few wells were found at groundwater levels lower than the corresponding surface water levels and were subjected to a high risk of pollution. Overall, these findings reinforce the notion that the management of surface and ground waters in an integrated approach is essential for attaining sustainable development of groundwater systems.