Correction: Heller et al. Characterization Methods along the Process Chain of Electrical Steel Sheet-From Best Practices to Advanced Characterization. Materials 2022, 15, 32.

In the original publication [...].

Material Design for Low-Loss Non-Oriented Electrical Steel for Energy Efficient Drives.

Due to the nonlinear material behavior and contradicting application requirements, the selection of a specific electrical steel grade for a highly efficient electrical machine during its design stage is challenging. With sufficient knowledge of the correlations between material and magnetic properties and capable material models, a material design for specific requirements can be enabled. In this work, the correlations between magnetization behavior, iron loss and the most relevant material parameters for non-oriented electrical steels, i.e., alloying, sheet thickness and grain size, are studied on laboratory-produced iron-based electrical steels of 2.4 and 3.2 wt % silicon. Different final thicknesses and grain sizes for both alloys are obtained by different production parameters to produce a total of 21 final material states, which are characterized by state-of-the-art material characterization methods. The magnetic properties are measured on a single sheet tester, quantified up to 5 kHz and used to parametrize the semi-physical IEM loss model. From the loss parameters, a tailor-made material, marked by its thickness and grain size is deduced. The influence of different steel grades and the chance of tailor-made material design is discussed in the context of an exemplary e-mobility application by performing finite-element electrical machine simulations and post-processing on four of the twenty-one materials and the tailor-made material. It is shown that thicker materials can lead to fewer iron losses if the alloying and grain size are adapted and that the three studied parameters are in fact levers for material design where resources can be saved by a targeted optimization.

Integrated Process Simulation of Non-Oriented Electrical Steel.

A tailor-made microstructure, especially regarding grain size and texture, improves the magnetic properties of non-oriented electrical steels. One way to adjust the microstructure is to control the production and processing in great detail. Simulation and modeling approaches can help to evaluate the impact of different process parameters and finally select them appropriately. We present individual model approaches for hot rolling, cold rolling, annealing and shear cutting and aim to connect the models to account for the complex interrelationships between the process steps. A layer model combined with a microstructure model describes the grain size evolution during hot rolling. The crystal plasticity finite-element method (CPFEM) predicts the cold-rolling texture. Grain size and texture evolution during annealing is captured by the level-set method and the heat treatment model GraGLeS2D+. The impact of different grain sizes across the sheet thickness on residual stress state is evaluated by the surface model. All models take heterogeneous microstructures across the sheet thickness into account. Furthermore, a relationship is established between process and material parameters and magnetic properties. The basic mathematical principles of the models are explained and demonstrated using laboratory experiments on a non-oriented electrical steel with 3.16 wt.% Si as an example.

Influence of Process Parameters on Grain Size and Texture Evolution of Fe-3.2 wt.-% Si Non-Oriented Electrical Steels.

The magnetic properties of non-oriented electrical steel, widely used in electric machines, are closely related to the grain size and texture of the material. How to control the evolution of grain size and texture through processing in order to improve the magnetic properties is the research focus of this article. Therefore, the complete process chain of a non-oriented electrical steel with 3.2 wt.-% Si was studied with regard to hot rolling, cold rolling, and final annealing on laboratory scale. Through a comprehensive analysis of the process chain, the influence of important process parameters on the grain size and texture evolution as well as the magnetic properties was determined. It was found that furnace cooling after the last hot rolling pass led to a fully recrystallized grain structure with the favorable ND-rotated-cube component, and a large portion of this component was retained in the thin strip after cold rolling, resulting in a texture with a low γ-fiber and a high ND-cube component after final annealing at moderate to high temperatures. These promising results on a laboratory scale can be regarded as an effective way to control the processing on an industrial scale, to finally tailor the magnetic properties of non-oriented electrical steel according to their final application.

Grain Size Influence on the Magnetic Property Deterioration of Blanked Non-Oriented Electrical Steels.

Non-oriented electrical steel sheets are applied as a core material in rotors and stators of electric machines in order to guide and magnify their magnetic flux density. Their contouring is often realized in a blanking process step, which results in plastic deformation of the cut edges and thus deteriorates the magnetic properties of the base material. This work evaluates the influence of the material's grain size on its iron losses after the blanking process. Samples for the single sheet test were blanked at different cutting clearances (15 µm-70 µm) from sheets with identical chemical composition (3.2 wt.% Si) but varying average grain size (28 µm-210 µm) and thickness (0.25 mm and 0.5 mm). Additionally, in situ measurements of blanking force and punch travel were carried out. Results show that blanking-related iron losses either increase for 0.25 mm thick sheets or decrease for 0.5 mm thick sheets with increasing grain size. Although this is partly in contradiction to previous research, it can be explained by the interplay of dislocation annihilation and transgranular fracturing. The paper thus contributes to a deeper understanding of the blanking process of coarse-grained, thin electrical steel sheets.

Characterization Methods along the Process Chain of Electrical Steel Sheet-From Best Practices to Advanced Characterization.

Non-oriented (NO) electrical steel sheets find their application in rotating electrical machines, ranging from generators for wind turbines to motors for the transportation sector and small motors for kitchen appliances. With the current trend of moving away from fossil fuel-based energy conversion towards an electricity-based one, these machines become more and more important and, as a consequence, the leverage effect in saving energy by improving efficiency is huge. It is already well established that different applications of an electrical machine have individual requirements for the properties of the NO electrical steel sheets, which in turn result from the microstructures and textures thereof. However, designing and producing tailor-made NO electrical steel sheet is still challenging, because the complex interdependence between processing steps, the different phenomena taking place and the resulting material properties are still not sufficiently understood. This work shows how established, as well as advanced and newly developed characterization methods, can be used to unfold these intricate connections. In this context, the respective characterization methods are explained and applied to NO electrical steel as well as to the typical processing steps. In addition, several experimental results are reviewed to show the strengths of the different methods, as well as their (dis)advantages, typical applications and obtainable data.