Effect of the Construction of Carbon Fiber Plate Insert to Midsole on Running Performance.

In this paper, to investigate the independent effect of the construction of the forefoot carbon-fiber plate inserted to the midsole on running biomechanics and finite element simulation, fifteen male marathon runners were arranged to run across a runway with embedded force plates at two specific running speeds (fast-speed: 4.81 ± 0.32 m/s, slow-speed: 3.97 ± 0.19 m/s) with two different experimental shoes (a segmented forefoot plate construction (SFC), and a full forefoot plate construction (FFC)), simulating the different pressure distributions, energy return, and stiffness during bending in the forefoot region between the SFC and FFC inserted to midsole. Kinetics and joint mechanics were analyzed. The results showed that the footwear with SFC significantly increased the peak metatarsophalangeal joint (MTPJ) plantarflexion velocity and positive work at the knee joint compared to the footwear with FFC. The results about finite element simulation showed a reduced maximum pressure on the midsole; meanwhile, not significantly affected was the longitudinal bending stiffness and energy return with the SFC compared to the FFC. The results can be used for the design of marathon running shoes, because changing the full carbon fiber plate to segment carbon fiber plate induced some biomechanical transformation but did not significantly affect the running performance, what is more, reducing the peak pressure of the carbon plate to the midsole by cutting the forefoot area of the carbon fiber plate could be beneficial from a long-distance running perspective for manufacturers.

Comparison of femur strain under different loading scenarios: Experimental testing.

Bone fracture, formation and adaptation are related to mechanical strains in bone. Assessing bone stiffness and strain distribution under different loading conditions may help predict diseases and improve surgical results by determining the best conditions for long-term functioning of bone-implant systems. In this study, an experimentally wide range of loading conditions (56) was used to cover the directional range spanned by the hip joint force. Loads for different stance configurations were applied to composite femurs and assessed in a material testing machine. The experimental analysis provides a better understanding of the influence of the bone inclination angle in the frontal and sagittal planes on strain distribution and stiffness. The results show that the surface strain magnitude and stiffness vary significantly under different loading conditions. For the axial compression, maximal bending is observed at the mid-shaft, and bone stiffness is also maximal. The increased inclination leads to decreased stiffness and increased magnitude of maximum strain at the distal end of the femur. For comparative analysis of results, a three-dimensional, finite element model of the femur was used. To validate the finite element model, strain gauges and digital image correlation system were employed. During validation of the model, regression analysis indicated robust agreement between the measured and predicted strains, with high correlation coefficient and low root-mean-square error of the estimate. The results of stiffnesses obtained from multi-loading conditions experiments were qualitatively compared with results obtained from a finite element analysis of the validated model of femur with the same multi-loading conditions. When the obtained numerical results are qualitatively compared with experimental ones, similarities can be noted. The developed finite element model of femur may be used as a promising tool to estimate proximal femur strength and identify the best conditions for long-term functioning of the bone-implant system in future study.

Finite Element Analysis of Impact for Helmeted and Non-helmeted Head.

This study investigated the influence of human head impact on the severity of traumatic brain injury. Simulation of the dynamic impact of a human head was performed using FEM (finite element method) and employing HIC (Head Injury Criterion). The study of traumatic brain injury included impacts with the occiput, temporal, forehead, and parietal part of the head, and the impact velocity at the surface ranged from 1 to 7 m/s. The following characteristics were considered and analyzed in the simulation: duration of the impact, intracranial pressure, HIC, and change in accelerations at the center of gravity of the brain. The computed distribution of pressure values in the brain during an impact confirmed the theory of inertial intracranial brain displacement. The effect of a protective helmet aimed at reducing the severity of traumatic brain injury was investigated, and a method to determine rational helmet parameters was developed. In the case of the protected head, impact acceleration occurred over a longer period of time, which yielded a reduction in the brain load compared to the unprotected head. The developed method allows us to predict the severity of traumatic brain injury (TBI) in the protected/unprotected human head and to provide recommendations for the determination of rational parameters for manufacturing personal protective equipment for the head.

Comparative Biomechanical Analysis of Stress-Strain State of the Elbow Joint After Displaced Radial Head Fractures.

Radial head fractures are becoming a major public health problem and are an increasingly important target for both clinical and mechanical researchers. In this work, comparative biomechanical analyses of the stress-strain state of a healthy elbow joint and elbow joints with radial head compression from 2 to 5 mm due to injury are performed. Three-dimensional models of the elbow joint with cartilage surfaces and ligaments were constructed based on the results of computed tomography. This study is focused on an elbow joint range of motion ranging from 0° to 120° flexion. Analysis of the stress-strain state of cartilage and ligaments under the influence of functional loads is conducted using a finite element method (FEM) and the ABAQUS software package. The results show that with increasing compression of the radial head, contact stress increases at the olecranon, which can lead to cartilage damage. Analysis of displacement shows that compression of the radial head during full extension of the elbow joint leads to an increased humeral shift from 1.14° ± 0.22 in the healthy joint to 10.3° ± 2.13 during 5-mm compression of the radial head. Mathematical modeling performed in this study proved that reducing the height of the radial head and the contact area between the radial head and the humeral head led to increased medial collateral ligament stresses of up to 36 ± 3.8 MPa. This work confirmed that the head of the radius is the main stabilizing structure of the elbow joint and that the medial collateral ligament is the second structure responsible for valgus stability of the elbow joint.

Numerical evaluation of bone remodelling and adaptation considering different hip prosthesis designs.

BACKGROUND: The change in mechanical properties of femoral cortical bone tissue surrounding the stem of the hip endoprosthesis is one of the causes of implant instability. We present an analysis used to determine the best conditions for long-term functioning of the bone-implant system, which will lead to improvement of treatment results. METHODS: In the present paper, a finite element method coupled with a bone remodelling model is used to evaluate how different three-dimensional prosthesis models influence distribution of the density of bone tissue. The remodelling process begins after the density field is obtained from a computed tomography scan. Then, an isotropic Stanford model is employed to solve the bone remodelling process and verify bone tissue adaptation in relation to different prosthesis models. FINDINGS: The study results show that the long-stem models tend not to transmit loads to proximal regions of bone, which causes the stress-shielding effect. Short stems or application in the calcar region provide a favourable environment for transfer of loads to the proximal region, which allows for maintenance of bone density and, in some cases, for a positive variation, which causes absence of the aseptic loosening of an implant. In the case of hip resurfacing, bone mineral density changes slightly and is closest to an intact femur. INTERPRETATION: Installation of an implant modifies density distribution and stress field in the bone. Thus, bone tissue is stimulated in a different way than before total hip replacement, which evidences Wolff's law, according to which bone tissue adapts itself to the loads imposed on it. The results suggest that potential stress shielding in the proximal femur and cortical hypertrophy in the distal femur may, in part, be reduced through the use of shorter stems, instead of long ones, provided stem fixation is adequate.

Influence of the fixation region of a press-fit hip endoprosthesis on the stress-strain state of the "bone-implant" system.

Although significant progress has been made in the development of total hip replacement, behaviour of the femoral component of an endoprosthesis in relation to the type of its fixation in the bone is still not fully understood. In this paper, behaviour of the femoral bone and the stem prosthesis is studied taking into account different types of prosthesis fixation in the medullary canal of the femur under the action of functional loads. For an analysis, a three-dimensional model of a femur has been developed based on the results of a computed tomography. The stress-strain state governing behaviour of the femoral bone and the stem prosthesis has been estimated with the use of the finite element method (FEM). The FEM analysis has shown that for the diaphyseal fixation, the area of contact between the surface of the endoprosthesis and the bone is insufficient and leads to large stresses in the implant accompanied by stress concentration in the distal femur. An increase in the area of contact between the implant and the bone raises the stiffness of the "bone-implant" system, which, in turn, reduces stresses in the implant. The applied metaphyseal-type fixation yielded an improvement of results regarding behaviour of the femoral bone and the stem prosthesis. Namely, the study yielded the distribution of stress in the bone similar to the physiological stress state.