Atomic Layer Deposition of Zirconia on Titanium Implants Improves Osseointegration in Rabbit Bones.

Purpose: Atomic layer deposition (ALD) is a method that can deposit zirconia uniformly on an atomic basis. The effect of deposited zirconia on titanium implants using ALD was evaluated in vivo. Methods: Machined titanium implants (MTIs) were used as the Control. MTIs treated by sandblasting with large grit and acid etching (SA) and MTIs deposited with zirconia using ALD are referred to as Groups S and Z, respectively. Twelve implants were prepared for each group. Six rabbits were used as experimental animals. To evaluate the osteogenesis and osteocyte aspects around the implants, radiological and histological analyses were performed. The bone-to-implant contact (BIC) ratio was measured and statistically analyzed to evaluate the osseointegration capabilities. Results: In the micro-CT analysis, more radiopaque bone tissues were observed around the implants in Groups S and Z. Histological observation found that Groups S and Z had more and denser mature bone tissues around the implants in the cortical bone area. Many new and mature bone tissues were also observed in the medullary cavity area. For the BIC ratio, Groups S and Z were significantly higher than the Control in the cortical bone area (P < 0.017), but there was no significant difference between Groups S and Z. Conclusion: MTIs deposited with zirconia using ALD (Group Z) radiologically and histologically showed more mature bone formation and activated osteocytes compared with MTIs (Control). Group Z also had a significantly higher BIC ratio than the Control. Within the limitations of this study, depositing zirconia on the surface of MTIs using ALD can improve osseointegration in vivo.

The potential bone regeneration effects of leptin- and osteolectin-coated 3D-printed PCL scaffolds: anin vivostudy.

This study investigated the effectiveness of bone regeneration upon the application of leptin and osteolectin to a three-dimensional (3D) printed poly(ϵ-caprolactone) (PCL) scaffold. A fused deposition modeling 3D bioprinter was used to fabricate scaffolds with a diameter of 4.5 mm, a height of 0.5 mm, and a pore size of 420-520 nm using PCL (molecular weight: 43 000). After amination of the scaffold surface for leptin and osteolectin adhesion, the experimental groups were divided into the PCL scaffold (control), the aminated PCL (PCL/Amine) scaffold, the leptin-coated PCL (PCL/Leptin) scaffold, and the osteolectin-coated PCL (PCL/Osteo) scaffold. Next, the water-soluble tetrazolium salt-1 (WST-1) assay was used to assess cell viability. All groups exhibited cell viability rates of >100%. Female 7-week-old Sprague-Dawley rats were used forin vivoexperiments. Calvarial defects were introduced on the rats' skulls using a 5.5 mm trephine bur. The rats were divided into the PCL (control), PCL/Leptin, and PCL/Osteo scaffold groups. The scaffolds were then inserted into the calvarial defect areas, and the rats were sacrificed after 8-weeks to analyze the defect area. Micro-CT analysis indicated that the leptin- and osteolectin-coated scaffolds exhibited significantly higher bone regeneration. Histological analysis revealed new bone and blood vessels in the calvarial defect area. These findings indicate that the 3D-printed PCL scaffold allows for patient-customized fabrication as well as the easy application of proteins like leptin and osteolectin. Moreover, leptin and osteolectin did not show cytotoxicity and exhibited higher bone regeneration potential than the existing scaffold.

Effects of TiO2 Nanotubes and Reduced Graphene Oxide on Streptococcus mutans and Preosteoblastic Cells at an Early Stage.

The effects of TiO2 nanotube (TNT) and reduced graphene oxide (rGO) deposition onto titanium, which is widely used in dental implants, on Streptococcus mutans (S. mutans) and preosteoblastic cells were evaluated. TNTs were formed through anodic oxidation on pure titanium, and rGO was deposited using an atmospheric plasma generator. The specimens used were divided into a control group of titanium specimens and three experimental groups: Group N (specimens with TNT formation), Group G (rGO-deposited specimens), and Group NG (specimens under rGO deposition after TNT formation). Adhesion of S. mutans to the surface was assessed after 24 h of culture using a crystal violet assay, while adhesion and proliferation of MC3T3-E1 cells, a mouse preosteoblastic cell line, were evaluated after 24 and 72 h through a water-soluble tetrazolium salt assay. TNT formation and rGO deposition on titanium decreased S. mutans adhesion (p < 0.05) and increased MC3T3-E1 cell adhesion and proliferation (p < 0.0083). In Group NG, S. mutans adhesion was the lowest (p < 0.05), while MC3T3-E1 cell proliferation was the highest (p < 0.0083). In this study, TNT formation and rGO deposition on a pure titanium surface inhibited the adhesion of S. mutans at an early stage and increased the initial adhesion and proliferation of preosteoblastic cells.

A leptin-loaded poly-ϵ-caprolactone 3D printing scaffold for odontoblastic differentiation in human dental pulp cells.

This study investigated the effects on odontoblast differentiation of a 3D-printed poly-ϵ-caprolactone (PCL) scaffold that incorporated leptin. Material extrusion-type 3D printing with a 43 000-molecular weight PCL material was used to fabricate a PCL scaffold with a 6 mm diameter, 1 mm height, and 270-340 µm pore size. The experimental groups were PCL scaffolds (control group), PCL scaffolds with aminated surfaces (group A), and PCL scaffolds with leptin on the aminated surface (group L). The aminated surface was treated with 1,6-hexanediamine and verified by ninhydrin analysis. Leptin loading was performed using Traut's reagent and 4-(N-Maleimidomethyl)cyclohexane-1-carboxylic acid 3-sulfo-N-hydroxysuccinimide ester sodium salt (Sulfo-SMCC). Groups A and L showed significantly higher surface wettability, pulp cell adhesion, and proliferation than the control group. Group L exhibited increased alkaline phosphatase, calcification deposits, and mRNA and protein expression of dentin sialophosphoprotein and dentin matrix acidic phosphoprotein 1 compared with the control group. In this study, a 3D-printed PCL scaffold containing leptin was enhanced odontoblast differentiation and dental pulp cells adhesion and proliferation.

Antibacterial Evaluation of Zirconia Coated with Plasma-Based Graphene Oxide with Photothermal Properties.

The alternative antibacterial treatment photothermal therapy (PTT) significantly affects oral microbiota inactivation. In this work, graphene with photothermal properties was coated on a zirconia surface using atmospheric pressure plasma, and then the antibacterial properties against oral bacteria were evaluated. For the graphene oxide coating on the zirconia specimens, an atmospheric pressure plasma generator (PGS-300, Expantech, Suwon, Republic of Korea) was used, and an Ar/CH4 gas mixture was coated on a zirconia specimen at a power of 240 W and a rate of 10 L/min. In the physiological property test, the surface properties were evaluated by measuring the surface shape of the zirconia specimen coated with graphene oxide, as well as the chemical composition and contact angle of the surface. In the biological experiment, the degree of adhesion of Streptococcus mutans (S. mutans) and Porphyromonas gingivalis (P. gingivalis) was determined by crystal violet assay and live/dead staining. All statistical analyzes were performed using SPSS 21.0 (SPSS Inc., Chicago, IL, USA). The group in which the zirconia specimen coated with graphene oxide was irradiated with near-infrared rays demonstrated a significant reduction in the adhesion of S. mutans and P. gingivalis compared with the group not irradiated. The oral microbiota inactivation was reduced by the photothermal effect on the zirconia coated with graphene oxide, exhibiting photothermal properties.

Assessment of Inhibition of Biofilm Formation on Non-Thermal Plasma-Treated TiO2 Nanotubes.

Peri-implantitis is an inflammatory disease similar to periodontitis, caused by biofilms formed on the surface of dental implants. This inflammation can spread to bone tissues and result in bone loss. Therefore, it is essential to inhibit the formation of biofilms on the surface of dental implants. Thus, this study examined the inhibition of biofilm formation by treating TiO2 nanotubes with heat and plasma. Commercially pure titanium specimens were anodized to form TiO2 nanotubes. Heat treatment was performed at 400 and 600 °C, and atmospheric pressure plasma was applied using a plasma generator (PGS-200, Expantech, Suwon, Republic of Korea). Contact angles, surface roughness, surface structure, crystal structure, and chemical compositions were measured to analyze the surface properties of the specimens. The inhibition of biofilm formation was assessed using two methods. The results of this study showed that the heat treatment of TiO2 nanotubes at 400 °C inhibited the adhesion of Streptococcus mutans (S. mutans), associated with initial biofilm formation, and that heat treatment of TiO2 nanotubes at 600 °C inhibited the adhesion of Porphyromonas gingivalis (P. gingivalis), which causes peri-implantitis. Applying plasma to the TiO2 nanotubes heat-treated at 600 °C inhibited the adhesion of S. mutans and P. gingivalis.

Effects of UV Absorber on Zirconia Fabricated with Digital Light Processing Additive Manufacturing.

This study evaluated the effect of UV absorbers on the dimensional accuracy of zirconia specimens fabricated by additive manufacturing using a digital light process. Zirconia suspension for additive manufacturing was prepared by setting the volume fractions (0, 0.005, 0.05, and 0.1%) of various UV absorbers. The effect of UV absorber content was evaluated through curing thickness, geometric overgrowth model design, linear deviation, and microstructure evaluation before and after sintering. Statistical analysis was performed by Kruskal-Wallis H and post-tested by the Bonferroni correction method. There was no significant difference in the cure depth according to the presence or absence of the UV absorber, the difference in geometric overgrowth was from 2.1 to 12.5%, and the overgrowth significantly decreased as the amount of added UV absorber increased. This result may contribute to improved precision of 3D multilayer ceramic products.

Antibacterial Effect of Zirconia Nanoparticles on Polyethyl Methacrylate Resin for Provisional Crowns.

Objective: Mid-to-long term use of provisional crowns in the oral cavity is associated with bacterial adhesion and biofilm formation, thus necessitating provisional crowns exhibiting antibacterial properties to prevent the occurrence of gingivitis and periodontal disease. This study aimed to evaluate the antibacterial effect of zirconia nanoparticle-containing polyethyl methacrylate (PEMA) resin for provisional restorations. Methods: Zirconia nanoparticles were added to the monomer of PEMA resin for provisional restorations, and the mixture was stirred for 2 h using a magnetic stirrer. Disk-shaped specimens were prepared by mixing the polymer with the nanoparticle solution. The control group contained pure PEMA resin samples, and the experimental groups Group Z2, Group Z4, and Group Z8 included PEMA resin specimens containing 2, 4, and 8% w/v zirconia nanoparticles, respectively. After analyzing the sample surfaces, the antibacterial effect of the specimens was evaluated using Streptococcus mutans. Statistical analysis was performed using Tukey's test and Mann-Whitney U-test, according to the normality result in the Shapiro-Wilk test. Results: FE-SEM and EDX analyses revealed the successful addition of zirconia nanoparticles. Results showed no significant difference in the measured values for surface roughness and contact angle between the experimental and control groups; however, adhesion and biofilm thickness of S. mutans were significantly decreased in Group Z2, Group Z4, and Group Z8 compared to the control group (P < 0.05, P < 0.01, P < 0.01, respectively). Conclusion: The addition of zirconia nanoparticles can lower the incidence of adhesion and biofilm thickness of S. mutans on PEMA resin used for provisional crowns. Thus, incorporating zirconia nanoparticles in repair materials for provisional crowns and PEMA resin can produce an antibacterial effect and prevent gingivitis, periodontal disease, and dental caries.

Effect of Non-Thermal Plasma Treatment of Contaminated Zirconia Surface on Porphyromonas gingivalis Adhesion and Osteoblast Viability.

Plasma treatment on a zirconia surface prevents bacterial contamination and maintains osteoblast activity. To assess the degree of adhesion of Porphyromonas gingivalis on a zirconia surface after non-thermal plasma (NTP) treatment, specimens were treated with plasma for 60, 300, and 600 s, after which P. gingivalis was inoculated onto the surface and incubated for 48 h. To assess osteoblast activity after NTP treatment, osteoblasts (MC3T3-E1) were dispensed onto the specimens contaminated with P. gingivalis immediately after NTP for 60 and 120 s, followed by incubation for 48, 72, and 96 h. P. gingivalis was cultured after 60 s of NTP treatment of zirconia. The NTP and control groups showed no significant difference (p = 0.91), but adhesion was significantly increased following NTP treatment for 300 s or longer (300, 600 s groups) (p < 0.05). After NTP treatment of P. gingivalis-contaminated zirconia, osteoblast activity significantly increased at 72 and 96 h (I60 and I120 s group) in the groups treated with plasma (p < 0.017). Application of NTP to dental zirconia implants for 60 s not only inhibits the proliferation of P. gingivalis, which causes peri-implantitis but also increases osseointegration on zirconia surfaces contaminated with P. gingivalis.

Biological Effects of the Novel Mulberry Surface Characterized by Micro/Nanopores and Plasma-Based Graphene Oxide Deposition on Titanium.

PURPOSE: This paper presents a technique for developing a novel surface for dental implants using a combination of nitriding and anodic oxidation, followed by the deposition of graphene oxide using atmospheric plasma. The effects of various surface treatments on bacterial adhesion and osteoblast activation were also evaluated. METHODS: CP titanium (control) was processed into disk-shaped specimens. Nitriding was conducted using vacuum nitriding, followed by anodic oxidation, which was performed in an electrolyte using a DC power supply, to form the novel "mulberry surface." Graphene oxide deposition was performed using atmospheric plasma with an inflow of carbon sources. After analyzing the sample surfaces, antibacterial activity was evaluated using Streptococcus mutans and Porphyromonas gingivalis bacteria. The viability, adhesion, proliferation, and differentiation of osteoblasts were also assessed. Analysis of variance (ANOVA) with Tukey's post-hoc test was used to calculate statistical differences. RESULTS: We observed that the mulberry surface was formed on samples treated with nitriding and anodic oxidation, and these samples exhibited more effective antibacterial activity than the control. We also found that the samples with additional graphene oxide deposition exhibited better biocompatibility, which was validated by osteoblast adhesion, proliferation, and differentiation. CONCLUSION: The development of the mulberry surface along with graphene oxide deposition inhibits bacterial adhesion to the implant and enhances the adhesion, proliferation, and differentiation of osteoblasts. These results indicate that the mulberry surface and graphene oxide deposition together can inhibit peri-implantitis and promote osseointegration.

Direct-Deposited Graphene Oxide on Dental Implants for Antimicrobial Activities and Osteogenesis.

OBJECTIVE: To determine the effects of graphene oxide (GO) deposition (on a zirconia surface) on bacterial adhesion and osteoblast activation. METHODS: An atmospheric pressure plasma generator (PGS-300) was used to coat Ar/CH4 mixed gas onto zirconia specimens (15-mm diameter × 2.5-mm thick disks) at a rate of 10 L/min and 240 V. Zirconia specimens were divided into two groups: uncoated (control; Zr) group and GO-coated (Zr-GO) group. Surface characteristics and element structures of each specimen were evaluated by field emission scanning electron microscope (FE-SEM), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and contact angle. Additionally, crystal violet staining was performed to assess the adhesion of Streptococcus mutans. WST-8 and ALP (Alkaline phosphatase) assays were conducted to evaluate MC3T3-E1 osteoblast adhesion, proliferation, and differentiation. Statistical analysis was calculated by the Mann-Whitney U-test. RESULTS: FE-SEM and Raman spectroscopy demonstrated effective GO deposition on the zirconia surface in Zr-GO. The attachment and biofilm formation of S. mutans was significantly reduced in Zr-GO compared with that of Zr (P < 0.05). While no significant differences in cell attachment of MC3T3-1 were observed, both proliferation and differentiation were increased in Zr-GO as compared with that of Zr (P < 0.05). SIGNIFICANCE: GO-coated zirconia inhibited the attachment of S. mutans and stimulated proliferation and differentiation of osteoblasts. Therefore, GO-coated zirconia can prevent peri-implantitis by inhibiting bacterial adhesion. Moreover, its osteogenic ability can increase bone adhesion and success rate of implants.

Hybrid porous zirconia scaffolds fabricated using additive manufacturing for bone tissue engineering applications.

For the formation of new bone in critical-sized bone defects, bioactive scaffolds with an interconnected porous network are necessary. Herein, we fabricated three-dimensional (3D) porous hybrid zirconia scaffolds to promote hybrid functionality, i.e., excellent mechanical properties and bioactive performance. Specifically, the 3D printed scaffolds were subjected to Zn-HA/glass composite coating on glass-infiltrated zirconia (ZC). In addition, to pertain the extracellular matrix of bone, biopolymer (alginate/gelatine) was embedded in a developed 3D construct (ZB and ZCB). A zirconia-printed scaffold (Z) group served as a control. The structural and mechanical properties of the constructed scaffolds were studied using essential characterization techniques. Furthermore, the biological performance of the designed scaffolds was tested by a sequence of in vitro cell tests, including the attachment, proliferation, and osteogenic differentiation of dental pulp cells (DPCs). The ZC and ZCB scaffolds exhibited 20% higher compression strength than the zirconia (Z) scaffolds. More importantly, the ZC constructs exhibited superior cell-adhesion, distribution, and osteogenic differentiation ability due to the synergistic effects of the composite coating. In addition, the biopolymer-embedded scaffolds (ZB, ZCB) showed an excellent biological and mechanical performance. Thus, our results suggest that the Zn-HA/glass composite-coated glass-infiltrated zirconia (ZC, ZCB) scaffolds are a dynamic approach to designing bioactive 3D scaffolds for the load-bearing bone regeneration applications.

Effect of Zinc Oxide Nanoparticle Addition to Polycaprolactone Periodontal Membranes on Antibacterial Activity and Cell Viability.

During the design of membranes for guided tissue regeneration (GTR) to treat periodontal diseases, infection of the exposed membranes and postoperative complications can be prevented by increasing bacterial resistance. This study evaluated the antibacterial activity of PCL/ZnO membranes and their effect on cell viability via addition of antibacterial zinc oxide (ZnO) nanoparticles to a biocompatible and biodegradable material such as polycaprolactone (PCL). Neat PCL membranes and PCL/ZnO membranes containing 0.5 wt.% and 5 wt.% ZnO were produced, and divided into PCL (0% ZnO), LZ (0.5 wt.% ZnO), and HZ (5 wt.% ZnO) groups, respectively. The surface characteristics of the membranes including morphological features and changes in composition were analyzed. Adhesion of bacteria, including Streptococcus mutans and Porphyromonas gingi-valis, was analyzed using a crystal violet assay. The proliferation of MC3T3-E1 osteoblasts was evaluated using a WST-8 assay. Significant differences were analyzed using the Kruskal-Wallis test (P < 0.05). The results of groups were compared using the Mann-Whitney test (P < 0.017). ZnO nanoparticles were dispersed in the PCL matrix of PCL/ZnO membranes. Compared with neat PCL membranes, their ability to form crystals decreased and their amorphous structure increased. The adhesion of S. mutans and P. gingivalis in the LZ and HZ groups containing ZnO was significantly decreased compared with that of the neat PCL membranes (P < 0.05). No significant differences were observed in the proliferation of MC3T3-E1 cells between the PCL/ZnO membranes and the neat PCL membranes both on days 2 and 5 of culture (P > 0.05). This study has demonstrated that the PCL membranes carrying the ZnO nanoparticles inhibited bacterial adhesion without affecting the viability of osteoblasts, suggesting the potential application of ZnO in GTR to increase antibacterial activity of membranes.

Atomic Layer Deposition of ZrO2 on Titanium Inhibits Bacterial Adhesion and Enhances Osteoblast Viability.

PURPOSE: The study was intended to create a uniform zirconia layer even on the surface of complex structures via atomic layer deposition (ALD). The impact of crystalline zirconia deposited by ALD on bacterial adhesion and osteoblast viability was assessed via surface treatment of dental implants. METHODS: Amorphous zirconia was deposited using an atomic layer deposition reactor (Atomic Classic, CN1, Hwaseong, Korea) on titanium discs. Heating the samples at 400°C resulted in crystallization. Samples were divided into three groups: the control group, the group carrying amorphous ALD-zirconia (Z group), and the heat-treated group following zirconia ALD deposition (ZH group).The surface of each sample was analyzed, followed by the assessment of adhesion of Streptococcus mutans and Porphyromonas gingivalis, and viability and differentiation of MC3T3-E1 cells. RESULTS: The adhesion of S. mutans and P. gingivalis was significantly reduced in the Z and ZH groups compared with the control group (P < 0.05). The viability of MC3T3-E1 cells was significantly increased in the ZH group compared with the control group (P < 0.001), while no significant differences were observed in the Z group (P > 0.05). Differentiation of MC3T3-E1 cells showed a marginally significant increase in the ZH group compared with the control group (P < 0.1), while no significant differences were found in the Z group (P > 0.1). CONCLUSION: Compared with the pure titanium group, the groups that were coated with zirconia via ALD showed a decreased adhesion of S. mutans during the early stages of biofilm formation and P. gingivalis adhesion inducing peri-implantitis, and an increase in MC3T3-E1 cell viability and differentiation. The findings indicate the possibility of treating the implant surface to reduce peri-implantitis and improve osseointegration.

Fabrication and Characterization of 45S5 Bioactive Glass/Thermoplastic Composite Scaffold by Ceramic Injection Printer.

45S5 bioactive glass (45S5) scaffolds were fabricated using a novel additive-manufacturing (AM) technology. A ceramic injection printer (CIP) was designed by combining injection molding and fused deposition modeling, for the fabrication of three-dimensional constructs of ceramic materials. A high fraction (50 vol%) of 45S5 powder was mixed with the thermoplastic polymer. The synthesized 45S5 composites were subjected to Brunauer-Emmett-Teller (BET) analysis, X-ray diffraction (XRD) analysis, and field-emission scanning electron microscopy (FE-SEM). The BET results of prepared 45S5 powder were confirmed to have a mean pore diameter of 11.402 nm, and specific surface area is 0.966 m²/g. The prepared 45S5/thermoplastic composite powder was subjected to Thermogravimetric/Differential thermal analysis (TG/DTA). The debinding process of polymer occurred at 192.5, 360.8, and 393 °C. The elastic modulus and ultimate stress of these scaffolds were measured to be 312.49±87.36 MPa and 21.83±6.67 MPa, respectively. The XRD results revealed the presence of Na6Ca3Si6O18 phases. The presence of Si, Ca, P, and Na was confirmed via energy-dispersive X-ray spectroscopy (EDS). The printed scaffold exhibited amorphous calcium phosphate (ACP) expression after immersion in simulated body fluid (SBF) and also it was observed that the intensity of the crystalline phase of 45S5 was decreased, as the immersion time increases. Bioactive glass composites with the high volume fraction can be able to construct 3D complex porous scaffolds using CIP.

Wear Behavior of the Human Enamel Antagonist to Different Glazed Zirconia.

In this study, the wear behavior of glazed zirconia was investigated to the antagonist with human enamel after simulated mastication. Twenty Y-TZP specimens were divided into 4 groups: untreated zirconia (Z), glazed zirconia with IPS e.max Ceram (GZE), glazed zirconia with VITA AKZENT® Plus (GZV), and glazed zirconia with glass (GZG). Glazing glass was mainly composed of SiO2, B2O3, Al2O3, Na2O and K2O (nearly 91 wt%). The surface roughness of the specimens was evaluated using roughness profiler. The maxillary premolar teeth were selected as the antagonist. The wear of human enamel against human enamel was used as a control. Five-disc specimens per group were subjected to chewing stimulation CS-4 (SD Mechatronic GmbH, Germany) for 240,000 cycles against human enamel. The wear loss of antagonistic teeth was calculated using a three-dimensional profiling system and the volume loss of the tooth was scanned using a 3D scanner. 3D data obtained before and after testing were overlapped using 3D software (Dentacian Software, EZplant, Korea). The wear loss of glazed zirconia GZE, GZV and GZG groups showed significantly lower than that of human enamel. Whereas, the zirconia (Z) group exhibits significantly lower volume loss than glazed zirconia and enamel. These results show that the wear of the glazing glass is comparable to other commercial glazing materials. Glazing materials are both more susceptible to wear the antagonist relative to zirconia.

Effect on Cell Viability with the Passage of Time After Atmospheric Plasma Treatment on Titanium Dioxide Surface.

Various attempts to modify the surface of dental implants have been made in order to improve the adhesion of osteocytes. Plasma treatment on dental implants has been suggested to improve osseointegration. This study examined the effect on cell viability with the passage of time after atmospheric plasma treatment. An atmospheric plasma generator (PGS-200 Plasma generator, Expantech Co., Korea) was used and the gas was mixed with the Ar2(99%)/O2(1%) composition and applied to the specimens. The passage of time was set to 7 immediately after treatment, after 30 minutes of treatment, after 60 minutes of treatment, after 90 minutes of treatment, after 24 hours of treatment, and after 48 hours of treatment. Surface property change with the passage of time after plasma treatment were confirmed by FE-SEM, surface roughness and X-ray photoelectron spectroscopy. Cell viability was evaluated by the WST-8 assay. The data were analyzed statistically using a 1-way ANOVA and Tukey's multiple comparisons test (α = .05). It was confirmed that the chemical composition of the surface changes as the passage of time increases after plasma treatment. The viability of L-929 cells was the highest immediately after plasma treatment, and cell viability decreased with increasing the passage of time. As a result of this study, it was confirmed that passage of time is a very important factor for the plasma treated surface.

Effect of Atmospheric Pressure Plasma Treatment on Shear Bond Strength Between Zirconia and Dental Porcelain Veneer.

Various surface treatments on zirconia have been reported for dental porcelain veneer. However, it has not been determined which of these treatments provide the highest bond strength. The purpose of this study is to compare the effect of airborne particle abrasion and atmospheric pressure plasma treatment on the shear bond strength between zirconia and dental porcelain veneer. The groups were divided into four groups according to the surface treatment method: the control group, the atmospheric pressure plasma treated group (group P), the airborne particle abrasion group (group A), the atmospheric pressure plasma treated group after the airborne particle abrasion (group AP). Atmospheric pressure plasma was applied on the specimens using a plasma generator (Plasma JET, POLYBIOTECH Co. Ltd., Gwangju, Korea) and airborne-particle abraded with 110 µm. The characteristics of surface treated zirconia were analyzed by 3D-OP, XRD, XPS and contact angle. The shear bond strength was tested using a universal testing machine. The shear bond strength of group P was significantly increased compared to that of the control group (P < 0.05). The shear bond strength of group AP was significantly increased as compared to group A (P < 0.05). There was no significant difference between the group P and group A (P > 0.05). As a result of this study, the atmospheric pressure plasma treatment showed significantly higher shear bond strength than control group, but similar to the airborne particle abrasion, and the atmospheric pressure plasma treatment after the airborne particle abrasion provided the highest shear bond strength. This study demonstrated that application atmospheric pressure plasma treatment on zirconia may be useful for increasing bond strength between zirconia and dental porcelain veneer.

Assessment of Inhibition of Biofilm Formation on TiO2 Nanotubes According to Non-Thermal Plasma Treatment Conditions and the Elapsed Time in the Atmosphere.

Periimplantitis is an inflammation similar to periodontitis, and is caused by biofilms formed on the surface of dental implants. Application of plasma on biomaterials has been reported to decrease the initial adhesion of microorganism by causing chemical changes without changing the surface morphology. The purpose of this study is to evaluate the effect of inhibition of biofilm formation on the elapsed time after plasma treatment. Non thermal plasma generator (PGS-200 Plasma generator, Expantech Co., Korea) was applied to the specimens. The elapsed time in the atmosphere was set to 5 immediately after treatment, after 30 minutes of treatment, after 60 minutes of treatment, after 90 minutes of treatment. Surface property change with the elapsed time in the atmosphere after plasma treatment were confirmed by X-ray photoelectron spectroscopy and contact angle. Inhibition of biofilm formation was evaluated by the fluorescent nucleic acid staining. It was confirmed that the chemical composition and bonding state of the surface changes as the elapsed time in the atmosphere increases after plasma treatment. The adhesion of Porphyromonas gingivalis was the lowest immediately after plasma treatment, and increased again with increasing elapsed time in the atmosphere after plasma treatment. As a result of this study, it was confirmed that elapsed time in the atmosphere is a very important factor for inhibition of biofilm formation.