Novel resin-based material containing ß-tricalcium phosphate nanoparticles for the reduction of dentin permeability.

OBJECTIVES: To synthesize and characterize a novel dentin adhesive containing Beta-Tricalcium Phosphate (ß-TCP) nanoparticles and test its ability to reduce dentin permeability (dP). METHODS: Experimental adhesives were prepared by mixing Bis-GMA, TEGDMA, HEMA (50/25/25 wt.%), photo-initiators, and inhibitors. The following groups were tested: Experimental adhesives without ß-TCP (Exp.); with 10 wt.% ß-TCP (Exp.10 wt.% ß-TCP); with 15 wt.% ß-TCP (Exp.15 wt.% ß-TCP), Scotchbond Multi-Purpose (SBMP) and Clearfil SE Protect Bond (CFPB). Degree of conversion (DC%, 10 and 20 s); Flexural Strength (FS), Knoop Hardness (KHN), and Cell Viability (OD%) tests were performed. dP was evaluated by hydraulic conductance, using human dentin disks (n=12), at three-time intervals: post-EDTA (T0); post-treatment (T1); and post-erosion/abrasion cycling (T2). Data were statistically analyzed (α=0.05). RESULTS: For all groups, exposure time for 20 s presented a higher DC% than for 10 s. For FS, filled adhesives did not differ from unfilled and from CFPB. Experimental adhesives did not differ among them and showed lower KHN than the commercial products. Cell viability did not differ among adhesives, except Exp. 15 wt.%, which showed lower OD% than Exp., Exp. 10% and, CFPB. For dP, only Exp.10 and 15 wt.% ß-TCP did not present difference between the times T1 and T2. After cycling, Exp.10 wt.% ß-TCP presented lower permeability than Exp. and CFPB. CONCLUSIONS: The incorporation of 10 wt.% ß-TCP nanoparticles into the resin-based dental material did not affect its mechanical properties and biocompatibility, and promoted the greatest reduction in dentin permeability, sustaining this effect under erosive/abrasive challenges. CLINICAL SIGNIFICANCE: A novel resin-based dental material containing ß-TCP nanoparticles was able to reduce dentin permeability, maintaining its efficacy after erosive/abrasive challenges. The synthesized material did not affect dental pulp cell viability and might be promising for other conditions that require dental remineralization, such as tooth wear and dental caries.

The effect of tooth bleaching using violet LED (405-410 nm) on the properties of resin-based composites.

BACKGROUND: The objective of this study was to evaluate the effect of bleaching techniques, including or not the use of violet light (405-410 nm), on resin-based composites' color, surface roughness, nanohardness, and elastic modulus. METHODS: Ninety-six disk-shaped specimens (12 mm x 2 mm; n = 12) were prepared using Filtek Z350 XT (Z350) and IPS Empress Direct (ED) resin-based composites. After 24 h, specimens were stained in red wine for 28 days. After staining, specimens were divided into four experimental groups: 40 % Hydrogen Peroxide (HP); Violet Light (VL); 40 % Hydrogen Peroxide associated with Violet Light (HP+VL), and a control group - no treatment (NT). Specimens were evaluated at six experimental times: initial (24 h after light curing); after staining and after the 1st, 2nd, 3rd, and 4th bleaching sessions regarding the color change (ΔE00, L*, a*, b*, and WID); roughness (Ra), nanohardness and elastic modulus (GPa). Two-way analysis of variance for repeated measures was performed (α=0.05 %). RESULTS: There was a statistically significant difference between staining and the 1st bleaching session for all ED groups (p<0.05). After the last bleaching session, there were no differences between the experimental and the control groups of both resin-based composites. Bleaching using violet light did not change the roughness, nanohardness and elastic modulus of the tested resin-based composites (p>0.05). CONCLUSIONS: Although hydrogen peroxide and violet light remove pigments from resin-based composites without affecting their surface roughness, nanohardness, and elastic modulus, the color change was similar to the one obtained by immersion in distilled water.

Tooth color change promoted by different whitening toothpastes under alternate cycles of staining and brushing.

OBJECTIVES: To compare the effect of whitening toothpastes with different mechanisms of action on discolored teeth subjected to additional staining/or not. METHODS: One hundred twenty tooth specimens were stained for 14 days (staining broth under constant agitation and pH=7) and then allocated into the groups of toothpastes with different whitening ingredients (n=10): 1. Regular - Colgate Total 12 Clean Mint; 2. CLWI - Colgate Luminous White Instant (blue pigment); 3. CLWA - Colgate Luminous White Advanced Expert (hydrogen peroxide); 4. CLWAC - Colgate Luminous White Activated Charcoal (activated charcoal); 5. OB3D - Oral-B 3D WHITE Brilliant Fresh (abrasive); 6. TW - Teeth Whitening (charcoal powder). Specimens were submitted to two experimental models: A. Daily staining-toothbrush cycling: staining solution (5min), toothbrushing (45 strokes) and artificial saliva (3h), 2x/day, for 5 days; B. Only toothbrushing (30.000 brushing strokes). Color change was determined with a spectrophotometer (CIEDE2000 and Whiteness Index for Dentistry - WID) and statistically analyzed (α=0.05). RESULTS: For both models, ΔE00 and Δa did not differ significantly between the whitening toothpastes and the regular. All groups showed a decrease in tooth yellowness (-Δb) and an increase in WID. Group Teeth Whitening exhibited a decrease in luminosity (-ΔL). In model A, Groups did not differ significantly from the Regular in terms of ΔL (p=0.35) and Δb (p=0.74). Groups CLWI and OB3D exhibited a decrease in luminosity. Reduced redness (-Δa) occurred only in Group CLWI. In Model B, Groups OB3D (p=0.021) and CLWA (p=0.001) exhibited higher change in luminosity than in Group Teeth Whitening. All exhibited increased redness (+Δa) and lightness (+ΔL), except the Regular, CLWAC, and Teeth Whitening. Group OB3D had a significantly higher change in Δb than the Regular (p=0.021). CONCLUSIONS: Irrespective of the mechanism of action, all toothpastes reduced tooth yellowness and promoted similar overall color change. Exposure of the teeth to additional staining during the toothbrushing cycles did not influence the effect of the whitening toothpastes. CLINICAL SIGNIFICANCE: Whitening toothpastes should be tested in conditions that more closely simulate their use in a clinical scenario, in which alternate cycles of staining and brushing occur on a daily basis. However, even in such conditions, they were unable to promote a color change that differed from that of a regular toothpaste.

Influence of substrate, cement and aging on the biaxial flexural strength of lithium disilicate / Influência do substrato, cimento e envelhecimento na resistência a flexão biaxial do dissilicato de lítio

Objective: To evaluate the biaxial flexural strength (BFS) of lithium disilicate (L), cemented on different substrates (epoxy resin - E and metal - M) with dual-cure resin cement (Rc) and zinc phosphate cement (Zc), not aged, thermally aged (TC) or thermo-mechanical aged (TC/MC). Material and Methods: Disks of L, E, and M were fabricated, and the cementation was performed according to the following groups: ERc (L+E+Rc); MRc (L+M+Rc); MZc (L+M+Zc); EZc (L+E+Zc). Ten samples from each described group were tested in BFS, ten more samples were subjected to TC (1×104 cycles between 5 ºC and 55 ºC water), and the last 10 samples were subjected to TC/MC (MC: 1.2×106 cycles, 50 N, 3.8 Hz). The BFS test was performed and scanning electron microscopy (SEM) was performed to evaluate the failure mode. The effect of the cementation strategy (cement/substrate) was compared in each aging method and the effect of the aging method was evaluated for each cementation strategy by one-way ANOVA and Tukey post-hoc test (α=0.05). Results: The strength values were highest to M (237.8 ~ 463.9 MPa), in comparison to the E (41.03 ~ 66.76 MPa), despite aging and luting agent. Flexural strength data decreased after TC and TC/MC in groups cemented with Zc, but was stable when cemented with Rc. SEM analysis indicated that failure origins were located at the tensile surface of the L. Conclusion: Lithium disilicate discs cemented to the metallic substrate presented the highest biaxial flexural strength. The cementation with dual-cure resin cement did not decrease BFS after aging (AU)

Objetivo: Avaliar a resistência à flexão biaxial (BFS) do dissilicato de lítio (L), cimentado sobre diferentes substratos (resina epóxi - E e metal - M) com cimento resinoso dual (Rc) e cimento de fosfato de zinco (Zc), não envelhecido, submetido ao envelhecido térmico (TC) ou ao envelhecido térmico-mecânico (TC/MC). Material e Métodos: Foram confeccionados discos de L, E e M, e a cimentação foi realizada de acordo com os seguintes grupos: ERc (L+E+Rc); MRc (L+M+Rc); MZc (L+M+Zc); EZc (L+E+Zc). Dez amostras de cada grupo descrito foram testadas em BFS, mais dez amostras foram submetidas à TC (1×104 ciclos de imersão em água entre 5 ºC e 55 ºC), e as últimas 10 amostras foram submetidas à TC/MC (MC: 1.2 ×106 ciclos, 50 N, 3.8 Hz). Foram realizados os testes de BFS e a microscopia eletrônica de varredura (MEV) para avaliar o modo de falha. O efeito da estratégia de cimentação (cimento/substrato) foi comparado em cada método de envelhecimento e o efeito do método de envelhecimento foi avaliado para cada estratégia de cimentação por ANOVA a um fator e teste post-hoc de Tukey (α=0,05). Resultados: Os valores de resistência foram maiores para M (237.8 ~ 463.9 MPa), em comparação com E (41.03 ~ 66.76 MPa), independentemente do envelhecimento e do agente cimentante utilizado. Os dados de resistência à flexão diminuíram após TC e TC/MC nos grupos cimentados com Zc, mas se mantiveram estáveis quando cimentados com Rc. A análise MEV indicou que a origem das falhas estava localizada na superfície de tração do L. Conclusão: Os discos de dissilicato de lítio cimentados ao substrato metálico apresentaram maior resistência à flexão biaxial. A cimentação com cimento resinoso dual não diminuiu o BFS após o envelhecimento (AU)

Development of a sodium fluoride and stannous chloride-containing gel for treatment of dental erosion.

This study synthesized and tested experimental gels containing fluoride (F-) and stannous (Sn2+) ions for the control of dental erosion. Enamel and dentin polished specimens were eroded (1% citric acid solution, 10 min) and randomly allocated into 5 groups (n=10): Placebo - Hydroxypropyl Methylcellulose (HMC) gel; F+Sn+HMC - 7,500 ppm F- / 15,000 ppm Sn2+; F+HMC - 7,500 ppm F-; Commercial acidulated phosphate fluoride gel (12,300 ppm F-); and Control - no treatment. After treatment (applied for 60 s), specimens underwent an erosion-remineralization cycling (5 min in 0.3% citric acid solution, 60 min in artificial saliva, 4×/day, 20 days). Surface loss (SL, in µm) was determined after the 5th, 10th and 20th days of cycling (α=0.05). For enamel, after 5 and 10 days, F+Sn+HMC presented the lowest SL, which did not differ from the commercial gel. After 20 days, no differences were found between commercial, F+HMC, and F+Sn+HMC groups. Placebo did not differ from the control at any time points, and both groups presented the highest SL when compared to the other groups. For dentin, on the 5th day, F+Sn+HMC, F+HMC and commercial did not differ significantly, showing lower SL than the control and the placebo. On the 10th day, F+Sn+HMC and commercial presented the lowest SL compared to control and placebo. After 20 days, only the commercial gel showed lower SL than the control and placebo. Thus, the experimental F+Sn+HMC gel was able to control the progression of tooth erosion.

Este estudo desenvolveu e testou géis experimentais contendo íons fluoreto (F-) e estanho (Sn2+) para o controle da erosão dentária. Os espécimes polidos, de esmalte e dentina, foram previamente erodidos (solução de ácido cítrico a 1%, 10 min) e alocados aleatoriamente em 5 grupos (n = 10): Placebo - gel de hidroxipropilmetilcelulose (HMC); F + Sn + HMC - 7.500 ppm F- / 15.000 ppm Sn2+; F + HMC - 7.500 ppm F-; Gel de flúor fosfato acidulado comercial (12.300 ppm F-); e Controle - sem tratamento. Após o tratamento (aplicado por 60 s), os espécimes foram submetidos a uma ciclagem de erosão-remineralização (5 min em solução de ácido cítrico a 0,3%, 60 min em saliva artificial, 4 × / dia, 20 dias). A perda de superfície (SL, em µm) foi determinada após o 5º, 10º e 20º dias de ciclagem (α = 0,05). Para o esmalte, após 5 e 10 dias, o F + Sn + HMC apresentou a menor PS, não diferindo do gel comercial. Após 20 dias, não foram encontradas diferenças entre os grupos comercial, F + HMC e F + Sn + HMC. O placebo não diferiu do controle em nenhum momento, e ambos os grupos apresentaram a maior PS, comparado aos demais grupos. Para dentina, no 5º dia , F + Sn + HMC, F + HMC e comercial não diferiram significativamente, apresentando menor PS que o grupo controle e placebo. No 10º dia, F+Sn+HMC e comercial apresentaram a menor PS comparado ao grupo controle e placebo. No 20º dia, apenas o gel comercial apresentou PS menor que o controle e o placebo. Assim, o gel experimental F + Sn + HMC foi capaz de controlar a progressão da erosão dentária.

Development of a sodium fluoride and stannous chloride-containing gel for treatment of dental erosion

Resumo Este estudo desenvolveu e testou géis experimentais contendo íons fluoreto (F-) e estanho (Sn2+) para o controle da erosão dentária. Os espécimes polidos, de esmalte e dentina, foram previamente erodidos (solução de ácido cítrico a 1%, 10 min) e alocados aleatoriamente em 5 grupos (n = 10): Placebo - gel de hidroxipropilmetilcelulose (HMC); F + Sn + HMC - 7.500 ppm F- / 15.000 ppm Sn2+; F + HMC - 7.500 ppm F-; Gel de flúor fosfato acidulado comercial (12.300 ppm F-); e Controle - sem tratamento. Após o tratamento (aplicado por 60 s), os espécimes foram submetidos a uma ciclagem de erosão-remineralização (5 min em solução de ácido cítrico a 0,3%, 60 min em saliva artificial, 4 × / dia, 20 dias). A perda de superfície (SL, em µm) foi determinada após o 5º, 10º e 20º dias de ciclagem (α = 0,05). Para o esmalte, após 5 e 10 dias, o F + Sn + HMC apresentou a menor PS, não diferindo do gel comercial. Após 20 dias, não foram encontradas diferenças entre os grupos comercial, F + HMC e F + Sn + HMC. O placebo não diferiu do controle em nenhum momento, e ambos os grupos apresentaram a maior PS, comparado aos demais grupos. Para dentina, no 5º dia , F + Sn + HMC, F + HMC e comercial não diferiram significativamente, apresentando menor PS que o grupo controle e placebo. No 10º dia, F+Sn+HMC e comercial apresentaram a menor PS comparado ao grupo controle e placebo. No 20º dia, apenas o gel comercial apresentou PS menor que o controle e o placebo. Assim, o gel experimental F + Sn + HMC foi capaz de controlar a progressão da erosão dentária.

Abstract: This study synthesized and tested experimental gels containing fluoride (F-) and stannous (Sn2+) ions for the control of dental erosion. Enamel and dentin polished specimens were eroded (1% citric acid solution, 10 min) and randomly allocated into 5 groups (n=10): Placebo - Hydroxypropyl Methylcellulose (HMC) gel; F+Sn+HMC - 7,500 ppm F- / 15,000 ppm Sn2+; F+HMC - 7,500 ppm F-; Commercial acidulated phosphate fluoride gel (12,300 ppm F-); and Control - no treatment. After treatment (applied for 60 s), specimens underwent an erosion-remineralization cycling (5 min in 0.3% citric acid solution, 60 min in artificial saliva, 4×/day, 20 days). Surface loss (SL, in µm) was determined after the 5th, 10th and 20th days of cycling (α=0.05). For enamel, after 5 and 10 days, F+Sn+HMC presented the lowest SL, which did not differ from the commercial gel. After 20 days, no differences were found between commercial, F+HMC, and F+Sn+HMC groups. Placebo did not differ from the control at any time points, and both groups presented the highest SL when compared to the other groups. For dentin, on the 5th day, F+Sn+HMC, F+HMC and commercial did not differ significantly, showing lower SL than the control and the placebo. On the 10th day, F+Sn+HMC and commercial presented the lowest SL compared to control and placebo. After 20 days, only the commercial gel showed lower SL than the control and placebo. Thus, the experimental F+Sn+HMC gel was able to control the progression of tooth erosion.

Impact of desensitizing/whitening toothpastes on tooth color change after abrasion and erosion-abrasion.

OBJECTIVE: To evaluate the impact of desensitizing toothpastes (D), their whitening versions (DW) and whitening toothpastes (W) on tooth color change. METHODS: Tooth specimens were allocated into 11 groups (n = 10): 1. Artificial saliva (control); 2. Sensodyne Repair & Protect (SRP-D); 3. Sensodyne Repair & Protect Whitening (SRP-DW); 4. Colgate Sensitive Pro-Relief (CSPR-D); 5. Colgate Sensitive Pro-Relief Real White (CSPR-DW); 6. Colgate Total 12 (CT12); 7. Colgate Total 12 Whitening (CT12-W); 8. Sensodyne True White (ST-W); 9. Curaprox Black Is White (CB-W); 10.Oral-B 3D White Perfection (OB3D-W) and 11. Erosion-only. They were submitted to two models: A. abrasion; B. erosion/abrasion. Color change (ΔE00 ), ΔL, Δa, and Δb were determined with a spectrophotometer. Data were statistically evaluated (α = 0.05). RESULTS: For both models, ∆E00 of D did not differ significantly from DW. An overall decrease in luminosity (-∆L) and increase (+∆b) in yellowness of the tooth occurred. In abrasion, all groups reduced redness (-∆a) and only SRP-DW differed from control (p = 0.016), but for ∆E00 , ∆L and ∆b, all toothpastes did not differ from the control. In erosion/abrasion, CB-W showed significantly lower ∆E00 and ∆b than the control (∆E00 : p = 0.026; ∆b: p = 0.005) and SRP-D (∆E00 : p = 0.028; ∆b: p = 0.025). Only SRP-DW, CSPR-DW, ST-W, CB-W, and erosion-only had increased redness (+∆a), but none differed from control. CONCLUSIONS: The toothpastes did neither promote whitening nor avoid the yellowish aspect of the tooth after abrasion and erosion-abrasion, regardless of their claim. CLINICAL SIGNIFICANCE: Desensitizing and/or whitening toothpastes induced similar changes on tooth color, without promoting whitening effect or reduction in its yellowish aspect.

Role of desensitizing/whitening dentifrices in enamel wear.

OBJECTIVES: To analyze the impact of desensitizing (D) and/or whitening (W) dentifrices on erosion and erosion-abrasion. METHODS: Enamel specimens were allocated into 10 groups (n = 20): 1. Artificial saliva (control); 2. Sensodyne Repair&Protect (SRP-D); 3. Sensodyne Repair&Protect Whitening (SRP-W); 4. Colgate Sensitive Pro-Relief (CSPR-D); 5. Colgate Sensitive Pro-Relief Real White (CSPRR-W); 6. Colgate Total 12 (CT); 7. Colgate Total 12 Professional Whitening (CTP-W); 8. Sensodyne True White (ST-W); 9. Curaprox Black is White (CB-W); 10. Oral-B 3D White Perfection (OB3D-W). For abrasion (n = 10), 30,000 brushing strokes were performed and surface roughness (SR) was evaluated. Erosion-abrasion (n = 10) consisted of 1 % citric acid (2 min), artificial saliva (60 min); 6×/day; 5 days. Toothbrushing was carried out 2×/day (45 strokes). Surface loss (SL) was determined with an optical profilometer. Data were statistically analyzed (α = 0.05). RESULTS: Relative to SR, only OB3D-W had a significantly rougher surface than the control (p = 0.014). SRP-D, CSPR-D and ST-W showed no difference from the baseline. High SL was observed for ST-W, OB3D-W and CTP-W, without significant differences from the control. CT showed the lowest SL, not differing from SRP-D and SRP-W. There was a weak negative correlation between SL and concentration of free fluoride in the slurries, SL and SR, and SL and pH, all p > 0.05. CONCLUSIONS: Only one dentifrice increased surface roughness of enamel to a higher degree than brushing with saliva. Brushing with the test dentifrices did not cause higher enamel erosive wear than brushing with saliva. CLINICAL SIGNIFICANCE: This study enhances our knowledge on the effect of desensitizing and whitening dentifrices, indicating that they do not worsen enamel loss due to abrasion and they might be a safe option for individuals with erosive tooth wear.

Can the size and the luting material influence in the bond strength of the fiberglass post to dentin? / O comprimento e o tipo de cimento podem influenciar na adesão do pino de fibra de vidro a dentina?

Aim: To evaluate the influence of lengths and different luting agents on the bond strength of fiberglass posts' adhesion to dentin.Methods: Sixty single-root bovine teeth were endodontically treated and included in polyether and acrilyc resin to simulate a periodontal ligament. These were divided into 6 groups according to the post lengths (6, 10 or 14 mm) and luting agents (self-adhesive dual resin cement ­ U; or etch-and-rinse dual resin cement ­ A): U6, U10, U14, A6, A19, and A14. All fiberglass posts were cemented according to manufacturer instructions. After this, mechanical aging was performed (1.2x106 cycles; 4 Hz, 90 N). The push-out specimens were then conducted (2.0 ± 0.1 mm), with the test executed in a universal machine (10 kgf at 0.5 mm/min). Data obtained were submitted to the Kruskal-Wallis and Dunn's test. Results: No statistically significant difference was observed in bond strength between the groups due to the type of luting agent (p > 0.05). However, the isolated post-length factor showed significantly different results for the U groups (p < 0.05). The U10 group showed similar union values to U6 but statistically inferior to U14. Conclusion: bond strength of fiberglass posts of the same length as the dentin presented no differences according to the luting agent, but the post-length property influenced the bond strength when self-adhesive resin cement was used.

Objetivo: avaliar a influência dos agentes cimentantes e dos diferentes comprimentos de pinos na resistência de união de pinos de fibra de vidro a dentina. Métodos: Sessenta dentes bovinos uniradiculares tiveram a raiz endodonticamente tratada, e foram incluídos em poliéter e resina acrílica para simular o ligamento periodontal. Os espécimes foram divididos em seis grupos de acordo com o comprimento dos pinos (6, 10 ou 14mm) e dos agentes de cimentantes (cimento resinoso dual autoadesivo (RelyX U200, 3M ESPE) - U; ou cimento resinoso dual convencional (AllCem Core, FGM) - A: U6, U10, U14, A6, A19 e A14. Todos os pinos de fibra de vidro foram cimentados conforme as recomendações do fabricante. Após, o envelhecimento mecânico (1,2x106 ciclos; 4 Hz, 90 N) as amostras foram fatiadas para o teste de push-out (2,0 ± 0,1 mm) executado em uma máquina de ensaio universal (10 kgf a 0,5 mm/min). Os dados foram submetidos ao teste de Kruskal-Wallis e Dunn. Resultados: não houve diferença estatística na resistência de união entre os grupos devido ao tipo de agente cimentante (p > 0,05), mas houve para o comprimento dos pinos dos grupos U (p < 0,05). O grupo U10 apresentou valores de união semelhantes a U6, mas estatisticamente inferiores ao U14. Conclusão: a resistência de união dos pinos de fibra de vidro de um mesmo comprimento não apresentou diferenças mesmo quando cimentados com cimentos diferentes, mas o comprimento dos pinos isoladamente influenciou quando o cimento resinoso autoadesivo foi utilizado.