Bioinspired molecular catalysts with a unique tricopper architecture for highly efficient oxygen reduction reaction.

In situ growth of intertwined trinuclear copper complexes (nCu3) on a cellulose-derived carbon support (CMC) produced a high-performance electrocatalyst (CMC-nCu3) for the oxygen reduction reaction (ORR), which demonstrated superior performance in zinc-air batteries compared to a commercial Pt/C catalyst. This work highlights the importance of copper-based molecular catalysts with rich and intertwined tricopper structures for boosting both ORR activity and stability.

Creating Asymmetric Fe-N3C-N Sites in Single-Atom Catalysts Boosts Catalytic Performance for Oxygen Reduction Reaction.

Fine tuning of the metal site coordination environment of a single-atom catalyst (SAC) to boost its catalytic activity for oxygen reduction reaction (ORR) is of significance but challenging. Herein, we report a new SAC bearing Fe-N3C-N sites with asymmetric in-plane coordinated Fe-N3C and axial coordinated N atom for ORR, which was obtained by pyrolysis of an iron isoporphyrin on polyvinylimidazole (PVI) coated carbon black. The C@PVI-(NCTPP)Fe-800 catalyst exhibited significantly improved ORR activity (E1/2 = 0.89 V vs RHE) than the counterpart SAC with Fe-N4-N sites in 0.1 M KOH. Significantly, the Zn-air batteries equipped with the C@PVI-(NCTPP)Fe-800 catalyst demonstrated an open-circuit voltage (OCV) of 1.45 V and a peak power density (Pmax) of 130 mW/cm2, outperforming the commercial Pt/C catalyst (OCV = 1.42 V; Pmax = 119 mW/cm2). The density functional theory (DFT) calculations revealed that the d-band center of the asymmetric Fe-N3C-N structure shifted upward, which enhances its electron-donating ability, favors O2 adsorption, and supports O-O bond activation, thus leading to significantly promoted catalytic activity. This research presents an intriguing strategy for the designing of the active site architecture in metal SACs with a structure-function controlled approach, significantly enhancing their catalytic efficiency for the ORR and offering promising prospects in energy-conversion technologies.

Enhancing oxygen reduction activity of dinuclear copper complexes loaded on an N-doped carbon support via a low-temperature pyrolysis strategy.

Bioinspired by the active sites of multicopper oxidases (MCOs), bi/multinuclear copper complexes have attracted great attention in promoting catalytic activity for the oxygen reduction reaction (ORR). Herein, we report the preparation of a Cu-N-C electrocatalyst Cu-BPOZ@CNB-400 for efficient ORR, which was obtained by low temperature pyrolysis of a dinuclear 2,5-bis(2-pyridyl)-1,3,4-oxadiazole (BPOZ) copper complex loaded on a N-doped carbon support at 400 °C. Cu-BPOZ@CNB-400 exhibited a half-wave potential (E1/2) of 0.86 V vs. RHE for the ORR in 0.1 M KOH solution, which was significantly higher than that of the Cu-BPOZ@CNB-800 (E1/2 = 0.83 V) catalyst treated under high temperature (at 800 °C) and the control catalyst Cu-Phen@CNB-400 (E1/2 = 0.82 V) derived from low-temperature-treatment (at 400 °C) of a mononuclear phenanthroline-coordinated-Cu complex loaded on a N-doped carbon support. When Cu-BPOZ@CNB-400 was applied as the cathode catalyst in zinc-air batteries a maximum power density (Pmax) of 127 mW cm-2 could be achieved, demonstrating comparable catalyst performance to the commercial 20 wt% Pt/C (Pmax = 122 mW cm-2) and the control Cu-Phen@CNB-400 catalyst (Pmax = 105 mW cm-2) under similar experimental conditions. Low-temperature pyrolysis of dinuclear copper complexes on a carbon support improved the charge transfer efficiency, inhibited metal aggregation, and could produce highly dispersed Cu-N-C catalysts with dinuclear copper sites for promoting the 4e--reduction selectivity of the ORR. It thus provides a cost-effective approach for the controllable fabrication of efficient ORR catalysts to be applied for energy conversion devices.

A Recursive Non-Uniform Sampling Estimator for Asynchronous Nonlinear Systems.

In this paper, we consider the problem of asynchronous estimation in the presence of packet losses for the randomly sampling nonlinear system. Packet losses occur at the control input and at the measurement side. Firstly, the synchronization of the asynchronous sampling system is realized by weighting the state of the adjacent state update points. Secondly, the projection theorem is used to estimate the system state at the sampling time. Due to modeling errors and unmodeled dynamics, obtaining an accurate dynamic model is challenging. Therefore, observation inference based on interpolation techniques is proposed to solve the asynchronous estimation problem. Furthermore, the algorithm is extended to multi-sensor systems to obtain a distributed fusion estimator. Finally, simulation experiments are conducted to validate the effectiveness of the algorithm.

Coordination polymer derived Fe-N-C electrocatalysts with high performance for the oxygen reduction reaction in Zn-air batteries.

Developing high performance noble-metal-free electrocatalysts as an alternative to Pt-based catalysts for the oxygen reduction reaction (ORR) in energy conversion devices is highly desirable. We report herein the preparation of a coordination-polymer (CP)-derived Fe/CP/C composite as an electrocatalyst for the ORR with excellent activity and stability both in solution and in Zn-air batteries. The Fe/CP/C catalyst was obtained from the pyrolysis of an iron porphyrin Fe(TPP)Cl (5,10,15,20-tetraphenyl-21H,23H-porphyrin iron(III) chloride) grafted Zn-coordination polymer with dangling functional groups 4,4'-oxybisbenzoic acid and 4,4'-bipyridine ligands. The Fe/CP/C catalyst showed much higher ORR activity with a half-wave potential (E1/2) of 0.90 V (vs. RHE) than the Fe/C catalyst (E1/2 = 0.85 V) derived from the carbon-black-supported Fe porphyrins in 0.1 M KOH solution. When Fe/CP/C was used as the cathode electrocatalyst in Zn-air batteries (ZABs), the ZABs achieved a significantly higher open circuit voltage (OCV = 1.43 V) and maximum power density (Pmax = 142.8 mW cm-2) compared with Fe/C (OCV = 1.38 V, Pmax = 104.5 mW cm-2) and commercial 20 wt% Pt/C (OCV = 1.41 V, Pmax = 117.6 mW cm-2). Using dangling functional groups in CP to increase the loading efficiency of iron porphyrins offered a facile method to prepare high-performance noble-metal-free electrocatalysts for the ORR, which may provide promising applications to energy conversion devices.