Multi-angle in situ dynamic light scattering at a neutron spin echo spectrometer.

A new sample environment, called Bio-Oven, has been built for the Neutron Spin Echo (NSE) Spectrometer J-NSE Phoenix. It provides active temperature control and the possibility to perform Dynamic Light Scattering (DLS) measurements during the neutron measurement. DLS provides diffusion coefficients of the dissolved nanoparticles, and thus one can monitor the aggregation state of the sample on a time scale of minutes during the spin echo measurement times on the order of days. This approach helps to validate the NSE data or to replace the sample when its aggregation state influences the spin echo measurement results. The new Bio-Oven is an in situ DLS setup based on optical fibers decoupling the free space optics around the sample cuvette in a lightproof casing from the laser sources and the detectors. It collects light from three scattering angles simultaneously. Six different values of momentum transfer can be accessed by switching between two different laser colors. Test experiments were performed with silica nanoparticles with diameters ranging from 20 nm up to 300 nm. Their hydrodynamic radii were determined from DLS measurements and compared with the ones obtained by a commercial particle sizer. It was demonstrated that also the static light scattering signal can be processed and gives meaningful results. The protein sample apomyoglobin was used for a long-term test and in a first neutron measurement using the new Bio-Oven. The results prove that the aggregation state of the sample can be followed using in situ DLS along with the neutron measurement.

Superlattice deformation in quantum dot films on flexible substrates via uniaxial strain.

The superlattice in a quantum dot (QD) film on a flexible substrate deformed by uniaxial strain shows a phase transition in unit cell symmetry. With increasing uniaxial strain, the QD superlattice unit cell changes from tetragonal to cubic to tetragonal phase as measured with in situ grazing-incidence small-angle X-ray scattering (GISAXS). The respective changes in the optoelectronic coupling are probed with photoluminescence (PL) measurements. The PL emission intensity follows the phase transition due to the resulting changing inter-dot distances. The changes in PL intensity accompany a redshift in the emission spectrum, which agrees with the Förster resonance energy transfer (FRET) theory. The results are essential for a fundamental understanding of the impact of strain on the performance of flexible devices based on QD films, such as wearable electronics and next-generation solar cells on flexible substrates.

Multi-stage freezing of HEUR polymer networks with magnetite nanoparticles.

We observe a change in the segmental dynamics of hydrogels based on hydrophobically modified ethoxylated urethanes (HEUR) when hydrophobic magnetite nanoparticles (MNPs) are embedded in the hydrogels. The dynamics of the nanocomposite hydrogels is investigated using dielectric relaxation spectroscopy (DRS) and neutron spin echo (NSE) spectroscopy. The magnetic nanoparticles within the hydrophobic domains of the HEUR polymer network increase the size of these domains and their distance. The size increase leads to a dilution of the polymers close to the hydrophobic domain, allowing higher mobility of the smallest polymer blobs close to the "center". This is reflected in the decrease of the activation energy of the ß-process detected in the DRS data. The increase in distance leads to an increase of the size of the largest hydrophilic polymer blobs. Therefore, the segmental dynamics of the largest blobs is slowed down. At short time scales, i.e. 10(-9) s < τ < 10(-3) s, the suppression of the segmental dynamics is reflected in the α-relaxation processes detected in the DRS data and in the decrease of the relaxation rate Γ of the segmental motion in the NSE data with increasing concentration of magnetic nanoparticles. The stepwise (multi-stage) freezing of the small blobs is only visible for the pure hydrogel at low temperatures. On the other hand, the glass transition temperature (Tg) decreases upon increasing the MNP loading, indicating an acceleration of the segmental dynamics at long time scales (τ∼ 100 s). Therefore, it would be possible to tune the Tg of the hydrogels by varying the MNP concentration. The contribution of the static inhomogeneities to the total scattering function Sst(q) is extracted from the NSE data, revealing a more ordered gel structure than the one giving rise to the total scattering function S(q), with a relaxed correlation length ξNSE = (43 ± 5) Å which is larger than the fluctuating correlation length from a static investigation ξSANS = (17.2 ± 0.3) Å.

Water ingress into a casein film quantified using time-resolved neutron imaging.

The migration of water into a casein film was probed with neutron radiography. From the neutron transmission images, the evolution of the water saturation profiles was extracted. The results indicate that the water influx is dominated by imbibition but also contains a diffusional component. The time dependence of the water ingress was quantified using a diffusion-like equation previously also applied to imbibition. A water transport coefficient D = 0.9 × 10(-9) m(2) s(-1) was found. This value and direct observation of the images indicate that the time taken for a typical adhesive casein-based layer to become saturated with water is of the order of hours.

Laser-ablated titania nanoparticles for aqueous processed hybrid solar cells.

Titania nanoparticles are produced by laser ablation in liquid in order to initiate functionalization of titania with the polymer for the active layer. By combining these titania nanoparticles and water-soluble poly[3-(potassium-6-hexanoate)thiophene-2,5-diyl] (P3P6T) hybrid solar cells are realized.

Use of intermediate focus for grazing incidence small and wide angle x-ray scattering experiments at the beamline P03 of PETRA III, DESY.

We describe the new experimental possibilities of the micro- and nanofocus X-ray scattering beamline P03 of the synchrotron source PETRA III at DESY, Hamburg (Germany), which arise from experiments with smaller beam sizes in the micrometer range. This beamline has been upgraded recently to perform new kinds of experiments. The use of an intermediate focus allows for reducing the beam size of microfocused hard X-rays while preserving a large working distance between the focusing elements and the focus position. For the first time, this well-known methodology has been employed to grazing incidence small- and wide-angle X-ray scattering (GISAXS/GIWAXS). As examples, we highlight the applications to in situ studies using microfluidic devices in GISAXS geometry as well as the investigation of the crystallinity of thin films in GIWAXS geometry.

Polymer-coated PtCo nanoparticles deposited on diblock copolymer templates: chemical selectivity versus topographical effects.

Metal-polymer hybrid films are prepared by deposition of polymer-coated PtCo nanoparticles onto block copolymer templates. For templating, a thin film of the lamella-forming diblock copolymer poly(styrene-b-methyl methacrylate) P(S-b-MMA) is chemically etched and a topographical surface relief with 3 nm height difference is created. Two types of polymer-grafted PtCo nanoparticles are compared to explore the impact of chemical selectivity versus the topographical effect of the nanotemplate. A preferable wetting of the polystyrene (PS) domains with poly(styrenesulfonate) (PSS)-coated PtCo nanoparticles (instead of residing in the space between the domains) is observed. Our investigation reveals that the interaction between PSS-coated nanoparticles and PS domains dominates over the topographical effects of the polymer surface. In contrast, a non-selective deposition of poly(N-vinyl-2-pyrrolidone) (PVP)-coated PtCo nanoparticles and the formation of large metal-particle aggregates on the film is observed.

In situ X-ray study of the structural evolution of gold nano-domains by spray deposition on thin conductive P3HT films.

Gold (Au) nanoparticles are deposited from aqueous solution onto one of the most used conductive polymers, namely poly(3-hexylthiophene) (P3HT), using airbrush deposition. We report on the structure formation and packing of the Au nanoparticles after a 5 s spray cycle. In situ grazing incidence small-angle X-ray scattering (GISAXS) measurements with 20 ms time resolution allow a real-time observation of the emergence and evolution of the microstructure during a spray cycle and subsequent solvent evaporation. The results reveal multistage nanoscale ordering of the Au nanoparticles during the spray cycle. Further ex situ atomic force microscopy measurements of the sprayed films showed the formation of Au monolayer islands on top of the polymer film. Our study suggests that the solvent-substrate interaction as well as solvent evaporation kinetics are important factors that need to be taken into consideration in order to grow a compact uniform monolayer film for the fabrication of ultrathin films using airbrush deposition.

Note: Comparison of grazing incidence small angle x-ray scattering of a titania sponge structure at the beamlines BW4 (DORIS III) and P03 (PETRA III).

Grazing incidence small angle x-ray scattering (GISAXS) is a powerful technique for morphology investigation of nanostructured thin films. GISAXS measurements at the newly installed P03 beamline at the storage ring PETRA III in Hamburg, Germany, are compared to the GISAXS data from the beamline BW4 at the storage ring DORIS III, which had been used extensively for GISAXS investigations in the past. As an example, a titania thin film sponge structure is investigated. Compared to BW4, at beamline P03 the resolution of larger structures is slightly improved and a higher incident flux leads to a factor of 750 in scattered intensity. Therefore, the acquisition time in GISAXS geometry is reduced significantly at beamline P03.

Note: grazing incidence small and wide angle x-ray scattering combined with imaging ellipsometry.

The combination of grazing incidence small angle x-ray scattering (GISAXS) and grazing incidence wide angle x-ray scattering (GIWAXS) with optical imaging ellipsometry is presented as an upgrade of the available measurement techniques at the wiggler beamline BW4 of the Hamburger Synchrotronstrahlungslabor. The instrument is introduced with the description of the alignment procedure to assure the measurement of imaging ellipsometry and GISAXS∕GIWAXS on the same sample spot. To demonstrate the possibilities of the new instrument examples of morphological investigation on films made of poly(3-hexylthiophene) and [6,6]-phenyl-C(61) butyric acid methyl ester as well as textured poly(9,9-dioctylfluorene-alt-benzo-thia-diazole) are shown.

Combining mixed titania morphologies into a complex assembly thin film by iterative block-copolymer-based sol­gel templating.

Sol­gel templating combined with iterative spin-coating steps are used to custom-tailor hierarchically structured titania thin films. Using poly(styrene-block-ethylene oxide) P(S-b-PEO) as the structure directing agent, a foam-like structure is combined with nanogranules. Both structural elements are merged into a complex assembly in thin film geometry. The resulting morphology is pictured by SEM and probed with GISAXS. The installed mesoporous titania sandwich structure exhibits holes with a size of 45 nm which makes it promising for applications in photovoltaics or photocatalysis. An optical characterization completes the structural investigation.

In situ observation of cluster formation during nanoparticle solution casting on a colloidal film.

We present a real-time study of the nanostructuring and cluster formation of gold nanoparticles deposited in aqueous solution on top of a pre-structured polystyrene colloidal thin film. Cluster formation takes place at different length scales, from the agglomerations of the gold nanoparticles to domains of polystyrene colloids. By combining in situ imaging ellipsometry and microbeam grazing incidence small-angle x-ray scattering, we are able to identify different stages of nanocomposite formation, namely diffusion, roughness increase, layer build-up and compaction. The findings can serve as a guideline for nanocomposite tailoring by solution casting.

Microfluidic emulsion separation-simultaneous separation and sensing by multilayer nanofilm structures.

Emulsion separation is of high relevance for filtration applications, liquid-liquid-partitioning of biomolecules like proteins and recovery of products from droplet microreactors. Selective interaction of various components of an emulsion with substrates is used to design microfluidic flow chambers for efficient separation of emulsions into their individual components. Our lab-on-a-chip device consists of an emulsion separation cell with an integrated silicon sensor chip, the latter allowing the detection of liquid motion via the field-effect signal. Thus, within our lab-on-a-chip device, emulsions can be separated while the separation process is monitored simultaneously. For emulsion separation a surface energy step gradient, namely a sharp interface between the hydrophobic and hydrophilic parts of the separation chamber, is used. The key component of the lab-on-a-chip system is a multilayer and multifunctional nanofilm structure which not only provides the surface energy step gradient for emulsion separation but also constitutes the functional parts of the field-effect transistors. The proof-of-principle was performed using a model emulsion consisting of immiscible aqueous and organic solvent components. Droplet coalescence was identified as a key aspect influencing the separation process, with quite different effects during separation on open surfaces as compared to slit geometry. For a detailed description of this observation, an analytical model was derived and lattice Boltzmann computer simulations were performed. By use of grazing incidence small angle x-ray scattering (GISAXS) interfacial nanostructures during gold nanoparticle deposition in a flow field were probed to demonstrate the potential of GISAXS for in situ investigations during flow.

Structure and flow of droplets on solid surfaces.

The structure and flow of droplets on solid surfaces is investigated with imaging and scattering techniques and compared to simulations. To access nanostructures at the liquid-solid interface advanced scattering techniques such as grazing incidence small-angle x-ray scattering (GISAXS) with micro- and nanometer-sized beams, GISAXS and in situ imaging ellipsometry and GISAXS tomography are used. Using gold nanoparticle suspensions, structures observed in the wetting area due to deposition are probed in situ during the drying of the droplets. After drying, nanostructures in the wetting area and inside the dried droplets are monitored. In addition to drying, a macroscopic movement of droplets is caused by body forces acting on an inclined substrate. The complexity of the solid surfaces is increased from simple silicon substrates to binary polymer brushes, which undergo a switching due to the liquid in the droplet. Nanostructures introduced in the polymer brush due to the movement of droplets are observed.

Stability and dynamics of droplets on patterned substrates: insights from experiments and lattice Boltzmann simulations.

The stability and dynamics of droplets on solid substrates are studied both theoretically and via experiments. Focusing on our recent achievements within the DFG-priority program 1164 (Nano- and Microfluidics), we first consider the case of (large) droplets on the so-called gradient substrates. Here the term gradient refers to both a change of wettability (chemical gradient) or topography (roughness gradient). While the motion of a droplet on a perfectly flat substrate upon the action of a chemical gradient appears to be a natural consequence of the considered situation, we show that the behavior of a droplet on a gradient of topography is less obvious. Nevertheless, if care is taken in the choice of the topographic patterns (in order to reduce hysteresis effects), a motion may be observed. Interestingly, in this case, simple scaling arguments adequately account for the dependence of the droplet velocity on the roughness gradient (Moradi et al 2010 Europhys. Lett. 89 26006). Another issue addressed in this paper is the behavior of droplets on hydrophobic substrates with a periodic arrangement of square shaped pillars. Here, it is possible to propose an analytically solvable model for the case where the droplet size becomes comparable to the roughness scale (Gross et al 2009 Europhys. Lett. 88 26002). Two important predictions of the model are highlighted here. (i) There exists a state with a finite penetration depth, distinct from the full wetting (Wenzel) and suspended (Cassie-Baxter, CB) states. (ii) Upon quasi-static evaporation, a droplet initially on the top of the pillars (CB state) undergoes a transition to this new state with a finite penetration depth but then (upon further evaporation) climbs up the pillars and goes back to the CB state again. These predictions are confirmed via independent numerical simulations. Moreover, we also address the fundamental issue of the internal droplet dynamics and the terminal center of mass velocity on a flat substrate.

Phase and microphase separation of polymer thin films dewetted from silicon--a spin-echo resolved grazing incidence neutron scattering study.

An understanding of the structure of ultrathin polymer films on solid substrates has scientific importance in applications as well as in fundamental studies of polymer diffusion or adsorption. We present studies of the organization of dewetted droplets of polymers on a silicon surface using a new neutron scattering technique, spin-echo resolved grazing incidence scattering (SERGIS), that has the potential to address at the same time the droplet-droplet correlations and the chemical configuration inside each droplet. For the seminal experiments, the polarized neutron reflectometer EVA at the Institut Laue-Langevin, Grenoble, France, was equipped with a spin-echo setup, and measurements were taken on surface structures previously characterized by different techniques. The dewetted polymers used in our studies were pure polystyrene, a mixture of polystyrene and polyparamethylstyrene, and a diblock copolymer of the two homopolymers. Even with a provisional setup SERGIS, we were able to determine the correlation between the droplets, providing results in excellent agreement with those obtained by atomic force microscopy and grazing incidence small-angle X-ray and neutron scattering. In addition, it was confirmed that the correlation function for diblock copolymer droplets is more complex than for polymer mixtures, exhibiting partial ordering of the copolymer within each droplet.

Grazing incidence wide angle x-ray scattering at the wiggler beamline BW4 of HASYLAB.

We present an upgrade of the available measurement techniques at the wiggler beamline BW4 of the Hamburger Synchrotronstrahlungslabor (HASYLAB) to grazing incidence wide angle x-ray scattering (GIWAXS). GIWAXS refers to an x-ray diffraction method, which, based on the measurement geometry, is perfectly suited for the investigation of the material crystallinity of surfaces and thin films. It is shown that the overall experimental GIWAXS setup employing a movable CCD-detector provides the capability of reliable and reproducible diffraction measurements in grazing incidence geometry. Furthermore, the potential usage of an additional detector enables the simultaneous or successive measurement of GIWAXS and grazing incidence small angle x-ray scattering (GISAXS). The new capability is illustrated by the microbeam GIWAXS measurement of a thin film of the conjugated polymer poly(3-octylthiophene) (P3OT). The investigation reveals the semicrystalline nature of the P3OT film by a clear identification of the wide angle scattering reflexes up to the third order in the [100]-direction as well as the first order in the [010]-direction. The corresponding microbeam GISAXS measurement on the present morphology complements the characterization yielding the complete sample information from subnanometer up to micrometer length scales.

Elastic torsion effects in magnetic nanoparticle diblock-copolymer structures.

Magnetic properties of thin composite films, consisting of non-interacting polystyrene-coated γ-Fe(2)O(3) (maghemite) nanoparticles embedded into polystyrene-block-polyisoprene P(S-b-I) diblock-copolymer films are investigated. Different particle concentrations, ranging from 0.7 to 43 wt%, have been used. The magnetization measured as a function of external field and temperature shows typical features of anisotropic superparamagnets including a hysteresis at low temperatures and blocking phenomena. However, the data cannot be reconciled with the unmodified Stoner-Wohlfarth-Néel theory. Applying an appropriate generalization we find evidence for either an elastic torque being exerted on the nanoparticles by the field or a broad distribution of anisotropy constants.

Free Volume and Swelling in Thin Films of Poly(N-isopropylacrylamide) End-Capped with n-Butyltrithiocarbonate.

The free volume in thin films of poly(N-isopropylacrylamid) end-capped with n-butyltriocarbonate (nbc-PNIPAM) is probed with positron annihilation lifetime spectroscopy (PALS). The PALS measurements are performed as function of energy to obtain depth profiles of the free volume of nbc-PNIPAM films. The range of nbc-PNIPAM films with thicknesses from 40 to 200 nm is focused. With decreasing film thickness the free volume increases in good agreement with an increase in the maximum swelling capability of the nbc-PNIPAM films. Thus in thin hydrogel films the sorption and swelling behavior is governed by free volume.

Hydration behavior of casein micelles in thin film geometry: a GISANS study?

The water content of casein micelle films in water vapor atmosphere is investigated using time-resolved grazing incidence small-angle neutron scattering (GISANS). Initial dry casein films are prepared with a spin-coating method. At 30 degrees C, the formation of a water-equilibrated casein protein film is reached after 11 min with a total content of 0.36 g of water/g of protein. With increasing water vapor temperature up to 70 degrees C, an increase in the water content is found. With GISANS, lateral structures on the nanometer scale are resolved during the swelling experiment at different temperatures and modeled using two types of spheres: micelles and mini-micelles. Upon water uptake, molecular assemblies in the size range of 15 nm (mini-micelles) are attributed to the formation of a high-contrast D2O outer shell on the small objects that already exist in the protein film. For large objects (>100 nm), the mean size increases at high D2O vapor temperature because of possible aggregation between hydrated micelles. These results are discussed and compared with various proposed models for casein micelle structures.