Ultraviolet-Visible-Near-Infrared Broadband Photodetector Enabled by Cs2AgBiBr6: Sn/Conjugated Polymer Heterojunction.

Broadband photodetectors covering ultraviolet (UV) to near-infrared (NIR) wavelengths play an essential role in communications, imaging, and biosensing. Developing a single photodetector with a broadband optical response operating at room temperature can significantly reduce the complexity and cost of receiver systems for multispectral applications. In this work, utilizing the porous structure characteristics of Cs2AgBiBr6:Sn thin films, a self-powered detector with broad spectral response (UV-vis-NIR) was achieved by constructing an effective Cs2AgBiBr6:Sn/PDPP3T heterojunction. This photodetector possesses a broad response spectrum from 350 to 950 nm with an average detection rate exceeding 1011 Jones and maintains excellent photoelectric performance over two months. Sn2+ doping effectively reduces the bandgap of Cs2AgBiBr6, enhancing its near-infrared absorption and optimizing energy level alignment with conjugated polymer (diketopyrrolopyrrole-terthiophene, PDPP3T). More importantly, the porous structure derived from Sn doping significantly improves carrier extraction and transport under a near-infrared light response at the heterojunction interface. Utilizing its broad spectral response characteristics in the UV-vis-NIR range, a novel information transfer and encryption system employing full optical modulation has been realized within a single perovskite photodetector. This work provides a new approach to fabricating lead-free double perovskite broadband photodetectors with potential applications in photonic devices.

Acceleration of Fenton-like Reaction by Bimetal-Mediated Sludge Biochar for Tetracycline Removal.

The production of sludge biochar (SBC) from residual sludge offers a solution to the challenges associated with sludge disposal and facilitates the reutilization of resources. In the present research, a bimetallic-modified sludge biochar, designated as FeCu-SBC, was synthesized by varying the doping ratios of FeSO4 and CuSO4. This material was intended for the effective degradation of tetracycline (TC) in aqueous environments via the activation of peroxydisulfate. The FeCu2-SBC (90% degradation rate) composite, synthesized through the incorporation of Fe and Cu in a 1:2 ratio with SBC, exhibited a degradation rate of TC, which was 2.7 times higher than that of SBC (32.85% degradation rate) and 1.8 times higher than that of FeCu (50% degradation rate). Research examining the mechanisms involved revealed that FeCu underwent degradation solely through the radical (•OH) pathway, whereas FeCu2-SBC was subject to degradation through both radical (SO4•-) and nonradical (1O2) pathways. This phenomenon was attributed to the distinct π-π, C═O, and defect structures in FeCu2-SBC compared to FeCu, which facilitated the activation process leading to the production of reactive species. This investigation presented a cost-effective approach for producing bimetallic-modified sludge biochar, offering perspectives on determining the crucial elements influencing the streamlined TC degradation pathway.

Uptake and transport mechanisms for cadmium by Myriophyllum aquaticum in a constructed wetland.

Myriophyllum aquaticum (M. aquaticum), as a Cd-highly enriched and tolerant species, has greater application in phytoremediation of Cd-polluted waters. Mechanisms of Cd uptake and transport of M. aquaticum were comprehensively investigated in this work. Transport direction of Cd was observed both from the roots to the aboveground and vice versa. The aboveground can be harvested during vigorous growth and flowering periods, further improving the efficient phytoremediation of Cd-polluted wastewater. Moreover, analysis of transpiration inhibition, low-temperature treatment and metabolic inhibition indicated that the uptake and transport of Cd by M. aquaticum can be achieved via the coexistence of the free diffusion-dominated apoplast pathway dominated by transpiration and the "cellular pathway" dominated by active absorption, with the active energy-demanding cellular pathway playing a dominant role. The obtained results have important implications in the in-depth exploration of uptake, transport and distribution mechanisms of heavy metals during phytoremediation of aquatic plants.

Efficient Removal of Greenhouse Gases: Machine Learning-Assisted Exploration of Metal-Organic Framework Space.

Global warming is a crisis that humanity must face together. With greenhouse gases (GHGs) as the main factor causing global warming, the adoption of relevant processes to eliminate them is essential. With the advantages of high specific surface area, large pore volume, and tunable synthesis, metal-organic frameworks (MOFs) have attracted much attention in GHG storage, adsorption, separation, and catalysis. However, as the pool of MOFs expands rapidly with new syntheses and discoveries, finding a suitable MOF for a particular application is highly challenging. In this regard, high-throughput computational screening is considered the most effective research method for screening a large number of materials to discover high-performance target MOFs. Typically, high-throughput computational screening generates voluminous and multidimensional data, which is well suited for machine learning (ML) training to improve the screening efficiency and explore the relationships between the multidimensional data in depth. This Review summarizes the general process and common methods for using ML to screen MOFs in the field of GHG removal. It also addresses the challenges faced by ML in exploring the MOF space and potential directions for the future development of ML for MOF screening. This aims to enhance the understanding of the integration of ML and MOFs in various fields and broaden the application and development ideas of MOFs.

Excitation power-dependent multicolor upconversion in NaLnF4:Er3+ under 1532†nm irradiation for anti-counterfeiting application.

Upconversion (UC) materials are renowned for their ability to convert low-energy photons into high-energy ones. The manipulation of parameters allows for the observation of multicolored UC luminescence (UCL) within a single material system. While modulation of multicolored UCL commonly relies on excitation at approximately 980 nm, investigation into multicolored UC materials activated by a 1532 nm excitation source remains comparatively scarce. In this work, we introduce NaLnF4:Er3+ as a novel class of smart luminescent materials. When the power density of a 1532 nm laser increases from 0.5 to 20.0 W/cm2, the emission peak positions remain unchanged, but the red-to-green (R/G) ratio decreases significantly from 18.82 to 1.48, inducing a color shift from red to yellow and ultimately to green. In contrast, no color variation is observed when NaLnF4:Er3+ is excited with a 980 nm laser at different power densities. This power-dependent multicolored UCL of NaLnF4:Er3+ excited at 1532 nm can be attributed to the competitive processes of upward pumping and downward relaxation of electrons on the 4I9/2 level of Er3+. By utilizing the unique UC characteristics of NaLnF4:Er3+, its potential utility in anti-counterfeiting applications is demonstrated. Our research highlights the distinctive optical properties of NaLnF4:Er3+ and provides novel insights into the use of luminescent materials in optical anti-counterfeiting technologies.

Seeking the adsorption of tetracycline in water by Fe-modified sludge biochar at different pyrolysis temperatures.

The composite material SBC-Fe-x with sludge and Fe3+ was developed by different calcination temperatures (600, 700, and 800 °C) for the removal of tetracycline (TC). The adsorption rates of SBC-Fe-600, SBC-Fe-700, and SBC-Fe-800 were 77.5%, 89%, and 91%, respectively. Furthermore, the Langmuir model indicated that the maximum adsorption capacity of SBC-Fe-700 (157.93 mg/g) was three times greater than that of SBC-Fe-600. The conclusions were confirmed by a series of characterizations that SBC-Fe-700 showed a larger specific surface area, well-developed pore structure, rich oxygen-containing functional groups and a high degree of graphitization. The results of pH experiments indicated the broad applicability of SBC-Fe-700 for TC adsorption. In addition, SBC-Fe-700 suggested outstanding performance in different water environments. This work produced a feasible adsorbent for the removal of TC, and a new direction for sludge resource utilization was proposed.

Highly efficient upconversion luminescence in narrow-bandgap Y2Mo4O15.

Lanthanide-doped upconversion (UC) materials have been extensively investigated for their unique capability to convert low-energy excitation into high-energy emission. Contrary to previous reports suggesting that efficient UC luminescence (UCL) is exclusively observed in materials with a wide bandgap, we have discovered in this study that Y2Mo4O15:Yb3+/Tm3+ microcrystals, a narrowband material, exhibit highly efficient UC emission. Remarkably, these microcrystals do not display any four- or five-photon UC emission bands. This particular optical phenomenon is independent of the variation in doping ion concentration, temperature, phonon energy, and excitation power density. Combining theoretical calculations and experimental results, we attribute the vanishing emission bands to the strong interaction between the bandgap of the Y2Mo4O15 host matrix (3.37 eV) and the high-energy levels (1I6 and 1D2) of Tm3+ ions. This interaction can effectively catalyze the UC emission process of Tm3+ ions, which leads to Y2Mo4O15:Yb3+/Tm3+ microcrystals possessing very strong UCL intensity. The brightness of these microcrystals outshines commercial UC NaYF4:Yb3+,Er3+ green phosphors by a factor of 10 and is 1.4 times greater than that of UC NaYF4:Yb3+,Tm3+ blue phosphors. Ultimately, Y2Mo4O15:Yb3+/Tm3+ microcrystals, with their distinctive optical characteristics, are being tailored for sophisticated anti-counterfeiting and information encryption applications.

Electron Structure Tuned Oxygen Vacancy-Rich AuPd/CeO2 for Enhancing 5-Hydroxymethylfurfural Oxidation.

The design of high activity catalyst for the efficiently conversion of 5-hydroxymethylfurfural (HMF) to 2,5-furandicarboxylic acid (FDCA) gains great interest. The rationally tailoring of electronic structure directly affects the interaction between catalysts and organic substrates, especially molecular oxygen as the oxidant. This work, the bimetallic catalysts AuPd/CeO2 were prepared by the combining method of chemical reduction and photo-deposition, effectively concerting charge between Au and Pd and forming the electron-rich state of Au. The increasing of oxygen vacancy concentration of CeO2 by acidic treatment can facilitate the adsorption of HMF for catalysts and enhance the yield of FDCA (99.0 %). Moreover, a series of experiment results combining with density functional theory calculation illustrated that the oxidation performance of catalyst in HMF conversion was strongly related to the electronic state of interfacial Au-Pd-CeO2. Furthermore, the electron-rich state sites strengthen the adsorption and activation of molecular oxygen, greatly promoting the elimination of ß-hydride for the selective oxidation of 5-hydroxymethyl-2-furancarboxylic acid (HMFCA) to FDCA, accompanied with an outgoing FDCA formation rate of 13.21 mmol ⋅ g-1 ⋅ min-1 at 80 °C. The perception exhibited in this research could be benefit to understanding the effects of electronic state for interfacial sites and designing excellent catalysts for the oxidation of HMF.

Metal-Organic Frameworks Marry Sponge: New Opportunities for Advanced Water Treatment.

Metal-organic frameworks (MOFs) have garnered attention across various fields due to their noteworthy features like high specific surface area, substantial porosity, and adjustable performance. In the realm of water treatment, MOFs exhibit great potential for eliminating pollutants such as organics, heavy metals, and oils. Nonetheless, the inherent powder characteristics of MOFs pose challenges in terms of recycling, pipeline blockage, and even secondary pollution in practical applications. Addressing these issues, the incorporation of MOFs into sponges proves to be an effective solution. Strategies like one-pot synthesis, in situ growth, and impregnation are commonly employed for loading MOFs onto sponges. This review comprehensively explores the synthesis strategies of MOFs and sponges, along with their applications in water treatment, aiming to contribute to the ongoing advancement of MOF materials.

Constructing a Titanium Silicon Molecular Sieve-Based Z-Scheme Heterojunction with Enhanced Photocatalytic Activity.

Titanium silicon molecular sieve (TS-1) is an oxidation catalyst that possesses a long lifetime of charge transfer excited state, high Ti utilization efficiency, large specific surface area, and good adsorption property; therefore, TS-1 acts as a Ti-based photocatalyst candidate. In this work, TS-1 coupled Bi2MoO6 (TS-1/BMO) photocatalysts were fabricated via a facile hydrothermal route. Interestingly, the optimized TS-1/BMO-1.0 catalyst exhibited a decent photodegradation property toward tetracycline hydrochloride (85.49% in 120 min) under the irradiation of full spectrum light, which were 4.38 and 1.76 times compared to TS-1 and BMO, respectively. The enhanced photodegradation property of the TS-1/BMO-1.0 catalyst could be attributed to the reinforced light-harvesting capacity of the photocatalyst, high charge mobility, and suitable band structure for tetracycline hydrochloride degradation. In addition, the mechanism of photocatalytic degradation of tetracycline hydrochloride by the TS-1/BMO-1.0 catalyst was reasonably proposed based on the band structure, trapping, and ESR tests. This research provided feasible ideas for the design and construction of high-efficiency photocatalysts for contaminant degradation.

Catalytic oxidation of toluene by manganese oxides: Effect of K+ doping on oxygen vacancy.

Alkali metal potassium was beneficial to the electronic regulation and structural stability of transition metal oxides. Herein, K ions were introduced into manganese oxides by different methods to improve the degradation efficiency of toluene. The results of activity experiments indicated that KMnO4-HT (HT: Hydrothermal method) exhibited outstanding low-temperature catalytic activity, and 90% conversion of toluene can be achieved at 243°C, which was 41°C and 43°C lower than that of KNO3-HT and Mn-HT, respectively. The largest specific surface area was observed on KMnO4-HT, facilitating the adsorption of toluene. The formation of cryptomelane structure over KMnO4-HT could contribute to higher content of Mn3+ and lattice oxygen (Olatt), excellent low-temperature reducibility, and high oxygen mobility, which could increase the catalytic performance. Furthermore, two distinct degradation pathways were inferred. Pathway Ⅰ (KMnO4-HT): toluene → benzyl → benzoic acid → carbonate → CO2 and H2O; Pathway ⅠⅠ (Mn-HT): toluene → benzyl alcohol → benzoic acid → phenol → maleic anhydride → CO2 and H2O. Fewer intermediates were detected on KMnO4-HT, indicating its stronger oxidation capacity of toluene, which was originated from the doping of K+ and the interaction between KOMn. More intermediates were observed on Mn-HT, which can be attributed to the weaker oxidation ability of pure Mn. The results indicated that the doping of K+ can improve the catalytic oxidation capacity of toluene, resulting in promoted degradation of intermediates during the oxidation of toluene.

Surface Modification with CuFeS2 Nanocrystals to Improve the Efficiency and Stability of Perovskite Solar Cells.

Poor stability retards the industrialization of perovskite solar cells (PSCs). One of the effective ways to solve this issue is to modify the perovskite surface to improve the efficiency and stability of the PSCs. Herein, we synthesized CuFeS2 nanocrystals and applied them to modify the perovskite surface. The efficiency of the PSCs with CuFeS2 modification is improved to 20.17% from 18.64% for the control devices. Some investigations demonstrate that the CuFeS2 modification passivates the perovskite surface defects and induces better energy band arrangement. Furthermore, the stability of the PSCs with CuFeS2 modification is improved compared with the devices without CuFeS2 modification. The efficiency of the PSCs with CuFeS2 modification maintains 93% of its initial value, whereas that of the devices without CuFeS2 modification decreases to 61% of the initial value. This work demonstrates that CuFeS2 is a novel material used as a modification layer to enhance the efficiency and stability of the PSCs.

Highly efficient and stable quasi two-dimensional perovskite solar cells via synergistic effect of dual additives.

Recently, quasi two-dimensional (Q-2D) perovskites with alternating cations in the interlayer space (ACI) have attracted more attentions owing to their elevated stability compared with three-dimensional (3D) analogs. While the efficiency of the devices derived from Q-2D perovskites is much smaller than that based on 3D perovskites. Here, we utilized urea and methoxyamine hydrochloride (MOAH) dual additives to acquire high quality Q-2D ACI perovskite GA(MA)5Pb5I16 (GA = guanidinium, MA = methylammonium) films. The efficiency of the perovskite solar cells (PSCs) derived from the Q-2D perovskite films induced by the synergistic effect of urea and MOAH dual additives increases to 20.32% from 17.21% for the devices without additive. This efficiency enhancement could be attributed to the enlarged grain size, improved crystallinity, optimized quantum well thickness distribution, and reduced trap states of the perovskite films. Moreover, the solar cells with dual additives present improved stability. The efficiency of devices with dual additives holds 95% of the original value after storage for 1600 h in ambient air. These results prove that the synergistic effect of urea and MOAH is an effective method to achieve highly efficient and stable Q-2D PSCs.

Organic carbon accumulation and aggregate formation in soils under organic and inorganic fertilizer management practices in a rice-wheat cropping system.

Soil organic carbon (C) and aggregates are the important components of soil fertility and the foundation of sustainable agriculture. The storage and protection of SOC in aggregates is widely regarded as the material basis of soil organic C accumulation. However, current understanding of soil aggregate and its associated organic C is insufficient to elucidate the regulation mechanism of soil organic C. A nine-year field experiment including chemical fertilizer (FR) and organic manure (OM) treatments was set up in the eastern plain of Funiu Mountain, central China. Using chemical analysis, physical sieving as well as nuclear magnetic resonance (NMR) methods, we mainly probed into the response of soil organic C concentration and composition, and C functional groups, water-stable aggregates to different treatments. Furthermore, scanning electronic microscopy (SEM) and partial least square structural equation modelling (PLS-SEM) was conducted to characterise the different size aggregates and to analyse the mechanism of soil organic C accumulation and stabilisation at aggregate scales. After nine years of farming, OM treatment substantially increased soil organic C content (by 3.77 g kg-1) and significantly enhanced the formation of macro-aggregates (> 250 µm), while FR had no significant influence on soil organic C. At the aggregate scale, the amounts of soil organic C, C physical fractions (particulate and mineral-associated organic C), total nitrogen and microbial biomass carbon associated in macro-aggregates (> 250 µm) were obviously higher than that in micro-aggregates and silt + clay fraction, and OM treatment greatly increased the accumulation of soil organic C and its components in macro-aggregates. Moreover, microbial biomass carbon (MBC) amounts in aggregates were remarkably increased (27-116%) by the application of OM. And MBC had a positively effect on the physical fractions of SOC but not on the C chemical structure within aggregates. The present study indicated that soil organic C accumulation mainly rely on macro-aggregates (> 250 µm). Intra-particulate organic carbon (POC) and mineral-associated organic carbon (MOC) within macro-aggregates played an important role in soil organic C accumulation. Meanwhile, soil microbes were a driving force for the accumulation of soil organic C physical fractions (POC and MOC). We concluded that OM treatment accelerated the synergistic process between organic C sequestration and soil aggregation, and showed great potential to increase soil organic C accumulation.

Torrefaction characteristics of cellulose loaded with boric acid.

To explore the catalytic effect of boric acid on biomass, cellulose loaded with boric acid was roasted by a tubular furnace. The gaseous products were adsorbed by activated carbon and then analyzed by GC-MS. Boric acid was shown to improve the selectivity of the product levoglucosenone (LGO). The effects of the parameters such as boric acid loading, nitrogen flow, and temperature on the torrefaction behavior of cellulose were investigated. In the studied temperature range of 240-420 °C, the yield of LGO first increases and then decreases. In addition, its yield increases directly with increasing nitrogen flow rate. The results show that the highest LGO yield of 6.64% (analytical value) can be obtained under 10% (w/w) boric acid loading, 380 °C and nitrogen flow rate of 65 ml/min conditions.

Analysis of clinical application effects and challenges of early warning system for the high-risk obstetric women of China: A scoping review.

BACKGROUND: Obstetric critical illness is an important factor that leads to an increase in maternal mortality. Early warning assessment can effectively reduce maternal and neonatal mortality and morbidity. However, there are multiple early warning systems, and the effect and applicability of each system in China still need to be explored. OBJECTIVES: To elaborate on the application, effectiveness and challenges of the existing early warning systems for high-risk obstetric women in China and to provide a reference for clinical practice. DESIGN: A scoping review guided by the Arksey and O'Malley framework and reported using the Preferred Reporting Items for Systematic Reviews and Meta-Analysis for scoping review (PRISMA-ScR) guidelines. ELIGIBILITY CRITERIA: We included original studies related to early warning and excluded those that were guidelines, consensus and reviews. The included studies were published in Chinese or English by Chinese scholars as of June 2021. DATA SOURCES: CNKI, Wanfang, VIP, Cochrane, CINAHL, Embase, PubMed and Web of Science databases were searched systematically, and the reference sections of the included papers were snowballed. RESULTS: In total, 598 articles were identified. These articles were further refined using keyword searches and exclusion criteria, and 17 articles met the inclusion criteria. We extracted data related to each study's population, methods and results. Early warning tools, outcome indices, effects and challenges are discussed. CONCLUSIONS: Although all studies have shown that early warning systems have good application effects, the use of early warning systems in China is still limited, with poor regional management and poor sensitivity for specific obstetric women. Future research needs to develop more targeted early warning tools for high-risk obstetric women and address the current challenges in clinical applications.

High-Efficiency and Wavelength-Tunable Near-Infrared Emission of Lanthanide Ions Doped Lead-Free Halide Double Perovskite Nanocrystals toward Fluorescence Imaging.

Near-infrared (NIR) fluorescent materials show unique photophysical properties, which make them widely used in optical communication, night vision imaging, biomedicine, and other applications. However, the development of high-efficiency and wavelength-tunable NIR nanomaterials is still a challenge. Herein, a series of lanthanide ions doped Cs2AgIn0.99Bi0.01Cl6 double perovskite nanocrystals (DPNCs) with wavelength-tunable NIR light emission (800-1600 nm) have been synthesized. The optimal photoluminescence quantum yield (PLQY) of the DPNCs reaches 66.7%, which is a record value for DPNCs. It is mainly attributed to the contribution of NIR emission of lanthanide ions doped into DPNCs. More importantly, the series of NIR emission wavelengths of lanthanide ions doped Cs2AgIn0.99Bi0.01Cl6 DPNCs include not only shorter-wavelength NIR light (≤900 nm) but also longer-wavelength NIR light (>900 nm), which are more appropriate for foodstuff analysis and medical diagnosis applications. Furthermore, 11.2% Nd3+ doped Cs2AgIn0.99Bi0.01Cl6 DPNCs with the optimal PLQY were embedded in a polymethyl methacrylate (PMMA) polymer matrix (DPNCs@PMMA), and the stability of DPNCs modified by PMMA has been greatly improved. Finally, the 11.2% Nd3+ ions doped Cs2AgIn0.99Bi0.01Cl6 DPNCs@PMMA based NIR LEDs have demonstrated good night vision and human tissue penetration. This work indicates that lanthanide ions doped DPNCs have a potential in NIR light applications and could inspire future research to explore novel lanthanide ions doped semiconductor NCs based NIR LEDs.

Recent Progress in Doped g-C3N4 Photocatalyst for Solar Water Splitting: A Review.

Graphitic carbon nitride (g-C3N4) photocatalysis for water splitting is harvested as a fascinating way for addressing the global energy crisis. At present, numerous research subjects have been achieved to design and develop g-C3N4 photocatalysis, and the photocatalytic system still suffers from low efficiency that is far from practical applications. Here, there is an inspiring review on the latest progress of the doping strategies to modify g-C3N4 for enhancing the efficiency of photocatalytic water splitting, including non-metal doping, metal doping, and molecular doping. Finally, the review concludes a summary and highlights some perspectives on the challenges and future research of g-C3N4 photocatalysts.

One-step immobilization of ß-glucosidase in crude enzyme solution by recyclable UCST-responsive polymer with enhanced uniformly biocatalytic performance.

In this study, the upper critical solution temperature (UCST)-responsive polymers poly (ethylene oxide) monomethyl ether-block-poly(acrylamide-co-acrylonitrile) (PEG-b-p(AAM-co-AN) were synthesized and successfully utilized to immobilize ß-glucosidase in crude enzyme solution. These UCST-responsive ß-glucosidase biocatalysts (PEG-b-p(AAM-co-AN@LytA-Glu) have specific UCST with tunable transition temperature, which could be tuned the separation temperature to the desired temperature range. The P2 @ LytA-Glu with an UCST of about 42.9 â„ƒ was exploited by one-step covalent immobilization of ß-glucosidase in crude enzyme solution. The prepared P2 @ LytA-Glu exhibited significantly improved temperature, pH, storage, and operation stabilities compared with that of free enzyme. The catalytic rate of P2 @ Glu-LytA was 14.5% higher than that of P2-Glu (immobilized pure ß-glucosidase), which indicated that one-step immobilization of crude enzyme directly from crude enzyme solution was feasible, and it can greatly save the purification step and reduce the experimental cost. The engineered UCST-responsive immobilized enzymes are potentially useful for the practical green biocatalysis.

Design a flower-like magnetic graphite carbon microsphere for enhanced adsorption of 2,4-dichlorophenol.

2,4-Dichlorophenol (2,4-DCP) is a hazardous chlorinated organic chemical, so its removal is an important task to protect the whole ecosystem and human health. During the material preparation, the magnetic graphitic carbon adsorbent (HFMCM) with a sparse sheet-like stacking structure was formed by interlayer assembly of nickel hydroxide nanosheets and hydrothermal glucose carbon. The conditions for optimal performance of the adsorbent are 45 °C and pH 5. The maximum adsorption capacity of HFMCM-180 for 2,4-DCP is 147.06 mg·g-1. Adsorption behavior in accordance with Langmuir isothermal model and pseudo-second-order kinetic models. The adsorbent remains selective for 2,4-DCP in metal ion solutions. More than 75% of the adsorption capacity is maintained after five cycles of adsorption. Electrostatic interaction, hydrogen bonding, and π-π bonding play a major role in the adsorption of 2,4-DCP by HFMCM. The adsorbent was glucose as the carbon source, nickel sulfate as the magnetic source, and hexamethylenetetramine as the precipitant. Its carbonization after pretreatment with different hydrothermal temperatures resulted in the synthesis of flower-like graphitic carbon spheres with magnetic properties. The interconnected pore channels on the adsorbent surface conferred large specific surface area to the material. 2,4-DCP was efficiently adsorbed by π-π stacking, hydrogen bonding, and electrostatic attraction within the pore channels with low spatial potential resistance.