Enhancing the Responsiveness of Thermoelectric Gas Sensors with Boron-Doped and Thermally Annealed SiGe Thin Films via Low-Pressure Chemical Vapor Deposition.

Thermoelectric gas sensor (THGS) devices with catalysts and Si0.8Ge0.2 thin films of different boron doping levels of 1018, 1019, and 1020 cm-3 were fabricated, and their transport properties are investigated. SiGe films were deposited on Si3N4/SiO2 multilayers on Si substrates using low-pressure chemical vapor deposition (LPCVD) and thermally annealed at 1050 °C. The Seebeck coefficients of the SiGe films were increased after thermal annealing, ranging from 191 to 275 µV/K at temperatures of 74 to 468 °C in air, and reaching the highest power factor of 6.78 × 10-4 W/mK2 at 468 °C. The thermal conductivity of the SiGe films varied from 2.4 to 3.0 W/mK at 25 °C. The THGS detection performance was tested for the H2 gas in air from 0.01 to 1.0%, and compared to the thermoelectric properties of the SiGe films. The high-temperature annealing treatment process was successful in enhancing the thermoelectric performance of both the SiGe films and sensor devices, achieving the best THGS performance with the sensor device fabricated from the annealed SiGe film with 1018 cm-3 boron-doped Si0.8Ge0.2.

Examination of VOC Concentration of Aroma Essential Oils and Their Major VOCs Diffused in Room Air.

This study analyzed temporal variation of the composition of volatile organic compounds (VOCs) at different diffusion time of gaseous phase of aroma compounds of four essential oils, lavender, tea tree, eucalyptus, and melissa. GC/MS methodology with the trace gas sampling by a thermal desorption tube is used to quantitatively determine the concentration of the corresponding 14 kinds of major and original VOCs in four essential oils. This study revealed for the first time that the concentration level of gaseous phase composition is varied, with a diffusion time from that of the liquid phase at equilibrium with it and the VOCs in the essential oils are classified into two groups, depending on whether their concentration with the time. It is verified that the total concentration of VOCs of these essential oils in the room air diffused by the ultrasonic diffuser is as low as 0.6 ppb and decreased soon below 0.1 ppb.

Focused Ultrasound Thalamotomy for Refractory Essential Tremor: A Japanese Multicenter Single-Arm Study.

BACKGROUND: Several feasibility studies and a randomized, controlled, multicenter trial have demonstrated the safety and efficacy of unilateral transcranial magnetic resonance-guided focused ultrasound (FUS) lesioning of the ventral intermediate thalamic nucleus in treating essential tremor. OBJECTIVE: To evaluate the safety and efficacy of FUS thalamotomy in a Japanese patient cohort through a prospective, multicenter, single-arm confirmatory trial. METHODS: A total of 35 patients with disabling refractory essential tremor underwent unilateral FUS thalamotomy and were followed up for 12 post-treatment months. Safety was measured as the incidence and severity of treatment-related adverse events. Efficacy was measured as the tremor severity and quality of life improvements using the Clinical Rating Scale for Tremor and Questionnaire for Essential Tremor. RESULTS: The mean skull density ratio (SDR) was 0.47. There was a significant decrease in the mean postural tremor score of the treated hand from baseline to 12 mo by 56.4% (95% CI: 46.7%-66.1%; P < .001), which was maintained at last follow-up. Quality of life improved by 46.3% (mean overall Questionnaire for Essential Tremor score of 17.4 [95% CI: 12.1-22.7]) and there were no severe adverse events. The most frequent adverse event was gait disturbance and all events resolved. CONCLUSION: Unilateral FUS thalamotomy allowed significant and sustained tremor relief and improved the quality of life with an outstanding safety profile. The observed safety and efficacy of FUS thalamotomy were comparable to those reported in a previous multicenter study with a low SDR, and inclusion of the low SDR group did not affect effectiveness.

Mismatch between TOF MR Angiography and CT Angiography of the Middle Cerebral Artery may be a Critical Sign in Cerebrovascular Dynamics.

PURPOSE: Although time-of-flight (TOF)-magnetic resonance angiography (MRA) can clearly depict intracranial arteries, the arterial flow of middle cerebral artery (MCA) is occasionally not detected. We evaluated this phenomenon with reference to cerebrovascular dynamics. MATERIALS AND METHODS: Seventeen patients with suspected occlusion of MCA or internal carotid artery on TOF-MRA were enrolled. All patients underwent CT angiography (CTA) and quantitative cerebral blood flow (CBF) examination for measurement of resting CBF and cerebrovascular reactivity (CVR). Depending on appearance, patients were categorized into three groups. Group A (n=6) had MCA delineation on both MRA and CTA, while groups B (n=6) and C (n=5) had no signal on MRA, but Group B had a MCA delineation on CTA. RESULTS: No significant difference between resting CBF and CBF after the administration of acetazolamide was seen among 3 groups. In contrast, mean CVR in group B was -19.7±18.1%, which was significantly lower than group A [36.4±21.7% (p<0.05)], but not than group C (21.4±35.2%). Furthermore, all patients in group B displayed a so-called steal phenomenon. CONCLUSION: This study is the first to show that visualization of MCA on TOF-MRA closely correlates with CVR, and that a vascular pattern showing no MCA signal intensity on MRA but with MCA delineation on CTA indicates a critical cerebrovascular condition.

Utility of 3-dimensional ultrasound imaging to evaluate carotid artery stenosis: comparison with magnetic resonance angiography.

BACKGROUND: We evaluated the utility of 3-dimensional (3-D) ultrasound imaging for assessment of carotid artery stenosis, as compared with similar assessment via magnetic resonance angiography (MRA). METHODS: Subjects comprised 58 patients with carotid stenosis who underwent both 3-D ultrasound imaging and MRA. We studied whether abnormal findings detected by ultrasound imaging could be diagnosed using MRA. Ultrasound images were generated using Voluson 730 Expert and Voluson E8. RESULTS: The degree of stenosis was mild in 17, moderate in 16, and severe in 25 patients, according to ultrasound imaging. Stenosis could not be recognized using MRA in 4 of 17 patients diagnosed with mild stenosis using ultrasound imaging. Ultrasound imaging showed ulceration in 13 patients and mobile plaque in 6 patients. When assessing these patients, MRA showed ulceration in only 2 of 13 patients and did not detect mobile plaque in any of these 6 patients. Static 3-D B mode images demonstrated distributions of plaque, ulceration, and mobile plaque, and static 3-D flow images showed flow configuration as a total structure. Real-time 3-D B mode images demonstrated plaque and vessel movement. Carotid artery stenting was not selected for patients diagnosed with ulceration or mobile plaque. CONCLUSIONS: Ultrasound imaging was necessary to detect mild stenosis, ulcerated plaque, or mobile plaque in comparison with MRA, and 3-D ultrasound imaging was useful to recognize carotid stenosis and flow pattern as a total structure by static and real-time 3-D demonstration. This information may contribute to surgical planning.

CO responses of sensors based on cerium oxide thick films prepared from clustered spherical nanoparticles.

Various types of CO sensors based on cerium oxide (ceria) have been reported recently. It has also been reported that the response speed of CO sensors fabricated from porous ceria thick films comprising nanoparticles is extremely high. However, the response value of such sensors is not suitably high. In this study, we investigated methods of improving the response values of CO sensors based on ceria and prepared gas sensors from core-shell ceria polymer hybrid nanoparticles. These hybrid nanoparticles have been reported to have a unique structure: The core consists of a cluster of ceria crystallites several nanometers in size. We compared the characteristics of the sensors based on thick films prepared from core-shell nanoparticles with those of sensors based on thick films prepared from conventionally used precipitated nanoparticles. The sensors prepared from the core-shell nanoparticles exhibited a resistance that was ten times greater than that of the sensors prepared from the precipitated nanoparticles. The response values of the gas sensors based on the core-shell nanoparticles also was higher than that of the sensors based on the precipitated nanoparticles. Finally, improvements in sensor response were also noticed after the addition of Au nanoparticles to the thick films used to fabricate the two types of sensors.

Effect of Core-Shell Ceria/Poly(vinylpyrrolidone) (PVP) Nanoparticles Incorporated in Polymer Films and Their Optical Properties.

We fabricated hybrid films of pentaerythritol triacrylate (PETA) with core-shell ceria/poly(vinylpyrrolidone) (PVP) nanoparticles, which consist of cerium oxide as the core and PVP as the shell, and investigated the film optical properties. In this study, we used ceria/PVP nanoparticles with average diameters of 37, 49 and 91 nm. We obtained translucent films consisting of PETA with core-shell ceria/PVP nanoparticles. The core-shell ceria/PVP nanoparticles can reduce the transmittance of near-ultraviolet light. The transmittance of visible light and haze values depends not only on the thickness of the films, but also on the average diameter of the nanoparticles. A SEM observation and the optical analyses prove that the core-shell ceria/PVP nanoparticles do not aggregate into the PETA matrix.

Initial experience in evaluating the prevalence of unruptured intracranial aneurysms detected on 3-tesla MRI.

BACKGROUND: Given the very poor outcome of ruptured intracranial aneurysms, detection and treatment of unruptured intracranial aneurysms by a less invasive examination have become important. For this purpose, 3-tesla (3T) magnetic resonance imaging (MRI) is the most suitable candidate, owing to its high signal/noise ratio and frequency resolution. However, few reports have investigated the prevalence of intracranial aneurysms with high-tesla MRI. Here, we evaluated the prevalence of intracranial aneurysms and the effectiveness of a 3T MRI system in their detection. METHODS: During a 1-year period, a total of 3,414 consecutive patients undergoing MR angiography with 3T MRI for the first time were enrolled. Diagnosis of intracranial aneurysm was made by two neuroradiologically trained medical doctors under complete blinding to patient information. When intracranial aneurysm was suspected, volume-rendering images were created for more accurate diagnosis. RESULTS: Surprisingly, 317 unruptured intracranial aneurysms were identified in 286 of 3,414 cases (8.4%); 151 unruptured aneurysms (47.6%) occurred in the internal carotid artery, 85 (26.8%) in the middle cerebral artery, 54 (17.0%) in the anterior cerebral artery, and 27 (8.5%) in the posterior circulation. Of these, 152/317 (47.9%) were <3 mm, 104 (32.8%) ranged from 3 to 5 mm, 5 (11.0%) from 5 to 7 mm, and 26 (8.2%) were >7 mm. No significant difference in size was seen among the four locations. CONCLUSIONS: For the first time, this study assessed the detection rate of intracranial aneurysms using 3T MRI. Results showed a higher detection rate than previously documented. The reason for this higher rate is likely the improved ability of this modality to detect unruptured aneurysms in the internal carotid artery and those <3 mm.

Resistive oxygen gas sensors for harsh environments.

Resistive oxygen sensors are an inexpensive alternative to the classical potentiometric zirconia oxygen sensor, especially for use in harsh environments and at temperatures of several hundred °C or even higher. This device-oriented paper gives a historical overview on the development of these sensor materials. It focuses especially on approaches to obtain a temperature independent behavior. It is shown that although in the past 40 years there have always been several research groups working concurrently with resistive oxygen sensors, novel ideas continue to emerge today with respect to improvements of the sensor response time, the temperature dependence, the long-term stability or the manufacture of the devices themselves using novel techniques for the sensitive films. Materials that are the focus of this review are metal oxides; especially titania, titanates, and ceria-based formulations.

Effects of high-humidity aging on platinum, palladium, and gold loaded tin oxide--volatile organic compound sensors.

This study is an investigation of high-humidity aging effects on the total volatile organic compound (T-VOC) gas-sensing properties of platinum, palladium, and gold-loaded tin oxide (Pt,Pd,Au/SnO(2)) thick films. The sensor responses of the high-humidity aged Pt,Pd,Au/SnO(2), a non-aged Pt,Pd,Au/SnO(2), and a high-humidity aged Pt/SnO(2) to T-VOC test gas have been measured. The high-humidity aging is an effective treatment for resistance to humidity change for the Pt,Pd,Au/SnO(2) but not effective for the Pt/SnO(2). The mechanism of the high-humidity aging effects is discussed based on the change of surface state of the SnO(2) particles.

Resistive oxygen sensor using ceria-zirconia sensor material and ceria-yttria temperature compensating material for lean-burn engine.

Temperature compensating materials were investigated for a resistive oxygen sensor using Ce(0.9)Zr(0.1)O(2) as a sensor material for lean-burn engines. The temperature dependence of a temperature compensating material should be the same as the sensor material; therefore, the Y concentration in CeO(2)-Y(2)O(3) was optimized. The resistance of Ce(0.5)Y(0.5)O(2-δ) was independent of the air-to-fuel ratio (oxygen partial pressure), so that it was confirmed to function as a temperature compensating material. Sensor elements comprised of Ce(0.9)Zr(0.1)O(2) and Ce(0.5)Y(0.5)O(2-δ) were fabricated and the output was determined to be approximately independent of the temperature in the wide range from 773 to 1,073 K.

Diagnosis of unruptured intracranial aneurysms: 3T MR angiography versus 64-channel multi-detector row CT angiography.

BACKGROUND AND PURPOSE: We compared 3-dimensional time-of-flight magnetic resonance angiography (3D TOF MRA) using a 3-tesla (T) MR unit with 64-channel multi-detector row computed tomographic angiography (64-MDCTA) for detection and characterization of angiographically proven unruptured intracranial aneurysms. METHODS: Thirty-eight patients with 47 aneurysms and 8 patients without aneurysms underwent 3T, 3D TOF MRA; 64-MDCTA; and intra-arterial angiography. As a first study, 3 radiologists blinded to pertinent clinical information independently reviewed MRA and CTA images. We evaluated diagnostic accuracy using an alternative free-response receiver operating characteristic (AFROC) analysis and evaluated the sensitivity and specificity of each technique. Next, 2 radiologists used volume-rendering images generated from MRA or CTA data to evaluate the morphology of the 47 aneurysms detected, and MRA and CTA results were compared. Three-dimensional digital angiography (DA) images were used as the standard of reference. RESULTS: On the AFROC analysis, the value of the mean area under the AFROC curve (A(1)) was 0.91 for both modalities. Mean sensitivity of 89% and specificity of 76% for MRA were not significantly different from sensitivity of 87% and specificity of 79% for CTA. Therefore, when used to evaluate aneurysmal morphology, both modalities appear satisfactory for determining these vascular anomalies. CONCLUSION: Three-tesla, 3D TOF MRA and 64-MDCTA are excellent modalities with high diagnostic accuracy for evaluating unruptured intracranial aneurysms and no significant difference between them in diagnostic performance.