RESUMO
The frictional behavior of one-dimensional (1D) materials, including nanotubes, nanowires, and nanofibers, significantly influences the efficient fabrication, functionality, and reliability of innovative devices integrating 1D components. Such devices comprise piezoelectric and triboelectric nanogenerators, biosensing and implantable devices, along with biomimetic adhesives based on 1D arrays. This review compiles and critically assesses recent experimental techniques for exploring the frictional behavior of 1D materials. Specifically, it underscores various measurement methods and technologies employing atomic force microscopy, electron microscopy, and optical microscopy nanomanipulation. The emphasis is on their primary applications and challenges in measuring and characterizing the frictional behavior of 1D materials. Additionally, we discuss key accomplishments over the past two decades in comprehending the frictional behaviors of 1D materials, with a focus on factors such as materials combination, interface roughness, environmental humidity, and non-uniformity. Finally, we offer a brief perspective on ongoing challenges and future directions, encompassing the systematic investigation of the testing environment and conditions, as well as the modification of surface friction through surface alterations.
RESUMO
Silver nanoparticles (Ag NPs) have been produced by low-dose (1-20 kGy) gamma irradiation of silver nitrate in the presence of graphene-based material (graphene oxide or electrochemically exfoliated graphene). The large surface area of those graphene-based materials combined with the presence of oxygen-containing functional groups on the surface provided successful nucleation and growth of Ag nanoparticles, which resulted in a uniformly covered graphene surface. The obtained Ag nanoparticles were spherical with a predominant size distribution of 10-50 nm for graphene oxide and 10-100 nm for electrochemically exfoliated graphene. The photothermal efficiency measurement showed a temperature increase upon exposure to a 532 nm laser for all samples and the highest photothermal efficiency was measured for the graphene oxide/Ag NP sample prepared at 5 kGy. Electromagnetic interference (EMI) shielding efficiency measurements showed poor shielding for the composites prepared with graphene oxide. On the other hand, all composites prepared with electrochemically exfoliated graphene showed EMI shielding to some extent, and the best performance was measured for the samples prepared at 5 and 20 kGy doses.
RESUMO
Genetic tags allow rapid localization of tagged proteins in cells and tissues. APEX, an ascorbate peroxidase, has proven to be one of the most versatile and robust genetic tags for ultrastructural localization by electron microscopy (EM). Here, we describe a simple method, APEX-Gold, which converts the diffuse oxidized diaminobenzidine reaction product of APEX into a silver/gold particle akin to that used for immunogold labelling. The method increases the signal-to-noise ratio for EM detection, providing unambiguous detection of the tagged protein, and creates a readily quantifiable particulate signal. We demonstrate the wide applicability of this method for detection of membrane proteins, cytoplasmic proteins, and cytoskeletal proteins. The method can be combined with different EM techniques including fast freezing and freeze substitution, focussed ion beam scanning EM, and electron tomography. Quantitation of expressed APEX-fusion proteins is achievable using membrane vesicles generated by a cell-free expression system. These membrane vesicles possess a defined quantum of signal, which can act as an internal standard for determination of the absolute density of expressed APEX-fusion proteins. Detection of fusion proteins expressed at low levels in cells from CRISPR-edited mice demonstrates the high sensitivity of the APEX-Gold method.
Assuntos
Tomografia com Microscopia Eletrônica/métodos , Técnicas Genéticas , Imageamento Tridimensional/métodos , Animais , Ascorbato Peroxidases , Congelamento , Ouro , Camundongos , ProteínasRESUMO
The mechanisms responsible for the dielectric response of C-based microwave absorbers remain a long-standing theoretical question. Uncovering these mechanisms is critical to enhance their microwave absorption performance. To determine how different C forms alter the dielectric response of C-based absorbers, FeNi-capped carbon nanotubes (FeNi-CNTs) and FeNi-cored carbon nanoparticles (FeNi-CNPs) are synthesized, and a comparative study of their dielectric responses is then carried out in this study. The as-synthesized FeNi-CNTs and FeNi-CNPs have similar magnetic properties and complex permeabilities, but differ in complex permittivities. It is shown that FeNi-CNTs have a much stronger dielectric loss than FeNi-CNPs. At a thickness of 2.8 mm, a low optimal reflection loss of -32.2 dB and a broad effective absorption bandwidth of 8.0 GHz are achieved for FeNi-CNTs. Meanwhile, equivalent circuit models reveal that the CNT network of the FeNi-CNTs could introduce an electrical inductance that can effectively improve its dielectric loss capability. This study demonstrates that designing a composite with a tailored C form and composition is a successful strategy for tuning its microwave absorption performance. Furthermore, the equivalent circuit modeling is an effective tool for analyzing the dielectric response of the microwave absorbers, as is expected to be applicable for other metal-C composites.
RESUMO
It is imperative to understand the interfacial adhesive behaviour of nanowires (NW) integrated into a nanoelectromechanical system in order to design commercialisable nanogenerators as well as ultrasensitive sensors. Currently available interfacial adhesion characterisation techniques that utilise in situ electron microscopy subject nanoscale systems to a high-vacuum, electron-irradiated environment, potentially altering their interfacial interactions. Alternatively, force-sensing techniques conducted in air do not provide visual feedback of the interface, and therefore can only indirectly deduce adhesive properties. Here, we present an interface characterisation technique that enforces ZnO NWs to remain partially delaminated on a Si substrate, and permits optical observation of their deformed condition in air. NWs are draped over a wedge and are allowed to conform to their minimum energy state. We evaluate the strain energy stored in the suspended segment of each NW by determining their deflected shape from interferometry. We show that utilising a tailored Euler-Bernoulli beam model which accounts for the tapering and irregularity of a NW is crucial for accurately evaluating their interfacial adhesion energy. A nominal energy per unit interface area value of [capital Gamma, Greek, macron]F-B,irr,taper = 51.1 ± 31.9 mJ m-2 is obtained for the ZnO NW-Si substrate interface; a magnitude lower than that found using electron microscopy, and higher than the upper-bound of the theoretically predicted van der Waals interaction energy of γvdW = 7.2 mJ m-2. This apparent discrepancy has significant implications for any nanotribological study conducted inside an electron microscope. The results also implicate electrostatic and capillary interactions as significant contributors towards a NW's adhesive behaviour during device operation.
RESUMO
The adhesion and friction between two Al2O3 nanowires (NWs) was characterized by the use of optical microscopy based nanomanipulation, with which peeling, shearing and sliding was performed. The elastically deformed shape of the NWs during peeling and shearing was used to calculate the adhesion and frictional forces; force sensing was not required. The obtained adhesion stress between two Al2O3 NWs varied from 0.14 to 0.25 MPa, lower than that observed for carbon nanotube junctions, and was attributed to van der Waals attraction. Stick-slip was observed during the shearing and sliding of two NWs, and was the consequence of discrete contact between surface asperities. The obtained static and kinetic frictional stresses varied from 0.7 to 1.3 MPa and 0.4 to 0.8 MPa, respectively; significantly greater than the obtained adhesion stress.