Efficient bioremediation of indigo-dye contaminated textile wastewater using native microorganisms and combined bioaugmentation-biostimulation techniques.

In this work, the bioremediation of wastewater from the textile industry with indigo dye content was carried out using combined bioaugmentation, bioventilation, and biostimulation techniques. Initially, the inoculum was prepared by isolating the microorganisms from the textile wastewater in a 2 L bioreactor. Then, the respirometry technique was implemented to determine the affinity of the microorganisms and the substrate by measuring CO2 and allowed the formulation of an empirical mathematical model for the growth kinetics of the microorganism. Finally, the bioremediation was carried out in a 3 L bioreactor obtaining an indigo dye removal efficiency of 20.7 ± 1.2%, 24.0 ± 1.5%, and 29.7 ± 1.1% for equivalent wavelengths of 436 nm, 525 nm, and 620 nm. The chemical oxygen demand showed an average reduction of 88.9 ± 2.5%, going from 470.7 ± 15.6 to 52.3 ± 10.7 ppm after 30 days under constant agitation and aeration. A negative generalized exponential model was fitted to assess the affinity of the microorganism with the wastewater as a substrate by evaluating the production of CO2 during the bioremediation. Bioremediation techniques improve water discharge parameters compared to chemical treatments implemented in the industry, reducing the use of substances that can generate secondary pollution. Bioaugmentation, biostimulation, and bioventing of the textile wastewater in this study demonstrate the potential of these combined techniques to serve as an efficient alternative for indigo-contaminated wastewater in the textile industry.

Feasibility of Forward Osmosis to Recover Textile Dyes Using Single Salts and Multicomponent Draw Solutions.

The textile industry generates large volumes of water characterized mainly by an intense color coming from dyes that are difficult to process due to their synthetic base and the presence of aromatic components. Due to the stricter regulation on the discharge of these effluents, in order to reduce dye waste before discharge into natural channels, alternatives are being sought to manage this wastewater. In this work, the concentration of dyes in simulated wastewater from the textile industry was studied by forward osmosis (with a cellulose triacetate CTA membrane), with the aim of concentrating the dye for its future recovery and reincorporation into the production process. Two dyes of different nature were evaluated to study the efficiency of the proposed process, using NaCl and reverse osmosis brine from a model seawater desalination solution as extraction solutions. It was observed that dye type (reactive or direct) and their charge influence the color rejection with the forward osmosis membrane used. It was able to concentrate the dyes in the feed solution up to approximately 55% with the reverse osmosis brine from the model seawater desalination solution. Finally, the results demonstrate that the FO process is a promising option for concentrating dyes present in wastewater from the textile industry in order to reuse them in the dyeing process.

Theoretical Model for the Prediction of Water Flux during the Concentration of an Olive Mill Wastewater Model Solution by Means of Forward Osmosis.

Currently, understanding the dynamics of the interaction between the agents in a process is one of the most important factors regarding its operation and design. Membrane processes for industrial wastewater management are not strangers to this topic. One such example is the concentration of compounds with high added value, such as the phenolic compounds present in olive mill wastewater (OMW). This process is a viable option, thanks to the forward osmosis (FO) process, osmotically driven by a saline stream. In this context, the transport of the solute and the solvent through the FO membranes, although essential to the process, remains problematic. This paper presents a study to predict, by means of a theoretical model, the water flux for two membranes (a cellulose triacetate flat sheet and a polyamide hollow fiber with integrated aquaporin proteins) with different characteristics using a sodium chloride solution as the draw solution (DS). The novelty of this model is the consideration of the contribution of organic compounds (in addition to the inorganic salts) to the osmotic pressure in the feed side. Moreover, the geometry of the modules and the characteristics of the membranes were also considered. The model was developed with the ability to run under different conditions, with or without tyrosol (the compound chosen as representative of OMW phenolic compounds) in the feed solution (FS), and was fitted and evaluated using experimental data. The results presented a variability in the model prediction, which was a function of both the membrane used and the FS and DS, with a greater influence of tyrosol observed on the permeate flux in the flat cellulose triacetate membrane.

Nitrogen recovery from sludge centrate by membrane contactor: Influence of operating parameters and cleaning conditions.

In urban wastewater treatment, the sludge generated is treated by anaerobic digestion, to be subsequently dehydrated by centrifuges. Currently, the liquid fraction obtained in this dehydration process is recirculated at the head of the treatment plant. However, its high nitrogen and phosphorus content makes it an effluent with high added value. The recovery of these nutrients could be an excellent alternative for the production of fertilizers or other industrial applications. In this study, the use of a liquid-liquid phase membrane contactor is presented as a favorable solution for the recovery of ammoniacal nitrogen from sludge centrated. The polypropylene hollow fiber membrane was evaluated considering its ammonia removal and recovery capacity. For this, different parameters were evaluated: the influence of the type and concentration of the acid solution, the wastewater pH, the flow rates of feeding and the acid stripping solution, and the contact time. Results showed that with a contact time of 65 min, ammonia removal and recovery percentages of the order of 90% were achieved. The flow rates of the stripping and feed solutions together with the acid concentration did not have a significant influence on the removal but on the recovery. Concerning used acid, sulphuric and phosphoric acid solutions achieved better results than nitric acid solution. The most critical parameter was the pH, obtaining the highest removal and recovery of ammonium at the highest pH. Finally, a stable cleaning protocol was obtained, between preventive and moderate cleanings to avoid severe cleanings, keeping the membrane at its maximum capacity.

Removal of pharmaceutical compounds commonly-found in wastewater through a hybrid biological and adsorption process.

Nowadays, alternative options to conventional wastewater treatment should be studied due to rising concerns emerged by the presence of pharmaceuticals compounds (PhCs) in the aquatic environment. In this work, a combined system including biological treatment by activated sludge plus adsorption with activated carbon is proposed to remove three selected drugs (acetaminophen (ACT), caffeine (CAF) and ibuprofen (IBU)) in a concentration of 2 mg L-1 of each one. For it three sequencing batch reactors (SBR) were operated. SBR-B treated a synthetic wastewater (SWW) without target drugs and SBR-PhC and SBR-PhC + AC operated with SWW doped with the three drugs, adding into SBR-PhC + AC 1.5 g L-1 of a mesoporous granular activated carbon. Results showed that the hybrid system SBR-activated carbon produced an effluent free of PhCs, which in addition had higher quality than that achieved in a conventional activated sludge treatment in terms of lower COD, turbidity and SMP concentrations. On the other hand, five possible routes of removal for target drugs during the biological treatment were studied. Hydrolysis, oxidation and volatilization pathways were negligible after 6 h of reaction time. Adsorption route only was significant for ACT, which was adsorbed completely after 5 h of reaction, while only 1.9% of CAF and 5.6% of IBU were adsorbed. IBU was the least biodegradable compound.

Integrated Membrane Process for the Treatment and Reuse of Residual Table Olive Fermentation Brine and Anaerobically Digested Sludge Centrate.

Management of wastewater is a major challenge nowadays, due to increasing water demand, growing population and more stringent regulations on water quality. Wastewaters from food conservation are especially difficult to treat, since they have high salinity and high organic matter concentration. The aim of this work is the treatment of the effluent from a table olive fermentation process (FTOP) with the aim of reusing it once the organic matter is separated. The process proposed in this work consists of the following membrane-based technologies: Ultrafiltration (UF) (UP005, Microdyn Nadir), Forward Osmosis (FO) (Osmen2521, Hydration Technology Innovation) and Nanofiltration (NF) (NF245, Dow). The FO process was implemented to reduce the salinity entering the NF process, using the FTOP as draw solution and, at the same time, to concentrate the centrate produced in the sludge treatment of a municipal wastewater treatment plant with the aim of obtaining a stream enriched in nutrients. The UF step achieved the elimination of 50% of the chemical oxygen demand of the FTOP. The UF permeate was pumped to the FO system reducing the volume of the anaerobically digested sludge centrate (ADSC) by a factor of 3 in 6.5 h. Finally, the ultrafiltrated FTOP diluted by FO was subjected to NF. The transmembrane pressure needed in the NF stage was 40% lower than that required if the ultrafiltration permeate was directly nanofiltered. By means of the integrated process, the concentration of organic matter and phenolic compounds in the FTOP decreased by 97%. Therefore, the proposed process was able to obtain a treated brine that could be reused in other processes and simultaneously to concentrate a stream, such as the ADSC.

Changes in the process performance and microbial community by addition of the metabolic uncoupler 3,3',4',5-tetrachlorosalicylanilide in sequencing batch reactors.

A complete study about the effects of 3,3',4',5-tetrachlorosalicylanilide (TCS) on organic matter elimination performance, sludge production and on the microbial community of a biological wastewater treatment process has been performed. For this purpose two sequencing batch reactors (SBR) worked in parallel for 43 days with 0.8 mg·L-1 of TCS (SBR-1) and without this metabolic uncoupler (SBR-2). Results indicated that 63.3% of sludge reduction was achieved in SBR-1. However, COD removal efficiency was maintained in similar values in both reactors (89.1% and 92.1% in SBR-1 and SBR-2, respectively). The exhaustive mixed liquor characterization led to know deeply the action mechanism of TCS. In this way, a 69% of adenosine triphosphate (ATP) reduction was observed in SBR-1 in comparison with values measured in SBR-2. On the contrary, an increase in soluble microbial products (SMP) and DNA concentrations occurred as a consequence of TCS addition. Thus, it could be concluded that sludge reduction due to TCS addition was due to both uncoupling effect and cellular lysis. Also, increase in all microbial hydrolytic enzymatic activities measured was observed, which explained the stable performance achieved in SBR-1 despite to the results explained above. It should be highlighted that this uncoupler should not be used in biological treatments that require nitrogen elimination because nitrifying bacteria were affected by its addition (Nitrosomonas and Nitrospira). Finally, the 16S rRNA gene amplicon sequencing informed that an important reduction of bacterial diversity resulted in SBR-1 due to TCS addition.

Treatment of table olive processing wastewaters using novel photomodified ultrafiltration membranes as first step for recovering phenolic compounds.

Table olive processing wastewaters (TOPW) have high salt concentration and total phenolic content (TPC) causing many environmental problems. To reduce them, ultrafiltration (UF) was applied for treating TOPW. However, NaCl, which is the main responsible of salinity in TOPW, and phenols are small molecules that cannot be separated by conventional UF membranes. They have serious problems caused by fouling, which can be overcome using membrane modification techniques. For these reasons, photomodification may be an effective technique to obtain a stream rich in TPC due to the changes in membrane surface properties. UV-modification in the presence of two hydrophilic compounds (polyethylene glycol and aluminium oxide) was performed to achieve membranes with high reductions of organic matter and to keep the TPC as high as possible. Commercial polyethersulfone (PES) membranes of 30 kDa were used. Surface modification was evaluated using FTIR-ATR spectroscopy and membrane performance was studied by calculating the rejection ratios of colour, chemical oxygen demand (COD) and TPC. Results demonstrated that UF is a useful pre-treatment to reduce organic matter from TOPW, obtaining a permeate rich in TPC. PES/Al2O3 membranes displayed superior antifouling properties and rejection values, keeping high the TPC (>95%). Therefore, UF using modified membranes is an appropriate and sustainable technique for treating TOPW.

Study of the behaviour of different NF membranes for the reclamation of a secondary textile effluent in rinsing processes.

More demanding legal regulations for the wastewater disposal and water scarcity make necessary wastewater reuse in the industry. In particular, textile industry generates large amounts of wastewater with a high concentration of pollutants. Even though present biological or physical-chemical treatments are broadly in place, the quality of the final effluent is not good enough to allow its direct reuse. Consequently, a complementary membrane process is required in order to improve wastewater characteristics. In this work, six NF membranes were tested at different volume concentration factors in order to select the most appropriate one. The main studied criteria were the permeate quality for its reuse in the textile processes and the minimum membrane fouling effect. The different results obtained for the tested membranes were explained by membrane characterization parameters as contact angle, roughness and size exclusion. Taking these factors into consideration, TFC-SR2 has shown the overall best results because of the high permeate flux and the minimum fouling (in terms of the normalised flux reduction).