Evaluation of colour change, marginal adaptation, fracture strength, and failure type in maxillary and mandibular premolar zirconia endo-crowns.

OBJECTIVES: The objective of this in vitro study was to evaluate the effects of different preparation designs on the mean colour change (ΔE*), marginal adaptation, fracture resistance, and fracture types of maxillary and mandibular premolar endocrowns (ECs). METHODOLOGY: A total of 40 extracted maxillary and mandibular premolars were treated endodontically, and each type was subdivided according to the remaining axial height (remaining walls on all surfaces; 2-4 mm) and 2 mm inside the pulp chamber. Specimens were immersed in coffee for 14 days, ΔE* was determined, marginal adaptation was observed, fracture forces test was conducted, and the samples were examined visually at 10× magnification to evaluate failure type and identify fracture origin. The data were entered and analyzed using Statistical Package for Social Sciences, and significance between and within groups was evaluated through ANOVA. The p-value ≤ 0.05 was considered statistically significant. RESULTS: The ΔE* values of the maxillary premolar with 2 mm axial height were the highest (6.8 ± 0.89 units), whereas the lowest value was observed in the mandibular premolar with 4 mm axial height (2.9 ± 0.53 units). Significant differences (p < 0.05) in teeth and design were observed. The marginal adaptation of the mandibular premolar with 4 mm axial height was the highest (30.20 ± 1.53 µm), whereas the lowest marginal adaptation was observed in the maxillary premolar with 2 mm axial height (14.38 ± 0.99 µm), and the difference was statistically significant (p < 0.05). The maximum fracture force was observed in maxillary premolars with 2 mm axial height (2248.15 ± 134.74 N), and no statistically significant difference (p = 0.07) was observed between maxillary and mandibular premolars at 4 mm axial height. CONCLUSION: The recorded ΔE* values of the ECs were within clinically acceptable values or slightly higher, and the marginal adaption values were within acceptable and recommended clinical values in µm. EC preparation with 2 mm axial height in both arches recorded the highest fracture forces. Type III (split fracture) failure was recorded as the highest in the maxillary and mandibular premolar ECs with different axial wall heights.

Comparative Evaluation of Digital Cephalometric Tracing Applications on Mobile Devices and Manual Tracing.

BACKGROUND Cephalometric radiography evaluates facial skeleton development and aids in diagnosis and treatment phases (pre and post) in orthodontics. This study aimed to compare digital cephalometric tracing using a smartphone application (App), a tablet-based platform, and manual tracing in 30 orthodontic patients. MATERIAL AND METHODS Thirty orthodontic pretreatment, criteria based, lateral cephalometric radiographs were analyzed/grouped for Steiner analysis parameters (5 skeletal, 3 dentals, 1 soft tissue) by 3 tracing methods [manual - group (Gp M), smartphone (Android - OS9) - Gp S, tablet (Apple - IOS13) - Gp T) after mandatory standardization/calibration. Measurements include 5 angular (SNA, SNB, ANB, SNMPA, SNOP), 3 linear U1NA, L1NB, U1L1, and 1 soft tissue (S line) (millimeters and degrees). Inter-examiner rating was determined using Dahlberg's test. After normality distribution testing (Shapiro-Wilk), data were analyzed using one-way analysis of variance (ANOVA) for group differences. Homogeneity of variance was verified using the Levene test. Differences were determined on probability value of (p≤0.05). RESULTS The results showed that Steiner's analysis parameters were similar in all groups with homogenous variances. Highest differences in mean values were found for L1NB, U1L1, and S line measurement, with higher values being observed in Gp S tracings. However, these differences were not statistically significant (p≤0.05). All parameters, irrespective of being measured in either degrees or millimeters, had means comparable to each other. CONCLUSIONS Smartphone and tablet-based applications produced tracings that were comparable and reliable when compared to conventional manual tracings. Standardization of images, processing, printing, and calibration of devices is important to achieve good results.

Shear Strength of Repaired 3D-Printed and Milled Provisional Materials Using Different Resin Materials with and without Chemical and Mechanical Surface Treatment.

The aim of this study was to assess the shear bond strength of 3D-printed and milled provisional restorations using various resin materials and surface finishes. There were 160 preliminary samples in all, and they were split into two groups: the milled group and the 3D-printed group. Based on the resin used for repair (composite or polymethylmethacrylate (PMMA)) and the type of surface treatment utilized (chemical or mechanical), each group was further divided into subgroups. The specimens were subjected to thermocycling from 5 °C to 55 °C for up to 5000 thermal cycles with a dwell time of 30 s. The mechanical qualities of the repaired material underwent testing for shear bond strength (SBS). To identify the significant differences between the groups and subgroups, a statistical analysis was carried out. Three-way ANOVA was used to analyze the effects of each independent component (the material and the bonding condition), as well as the interaction between the independent factors on shear bond strength. Tukey multiple post-hoc tests were used to compare the mean results for each material under various bonding circumstances. The shear bond strengths of the various groups and subgroups differed significantly (p < 0.05). When compared to the milled group, the 3D-printed group had a much greater mean shear bond strength. When compared to PMMA repair, the composite resin material showed a noticeably greater shear bond strength. In terms of surface treatments, the samples with mechanical and chemical surface treatments had stronger shear bonds than those that had not received any. The results of this study demonstrate the effect of the fabrication method, resin type, and surface treatment on the shear bond strength of restored provisional restorations. Particularly when made using composite material and given surface treatments, 3D-printed provisional restorations showed exceptional mechanical qualities. These results can help dentists choose the best fabrication methods, resin materials, and surface treatments through which to increase the durability and bond strength of temporary prosthesis.