Effect of Non-Thermal Sulfur Hexafluoride Cold Plasma Modification on Surface Properties of Polyoxymethylene.

X-ray photoelectron spectroscopy was employed to reveal the differences in the chemical structure of the topmost layer after plasma modification. It was found out that changes in the surface properties of the polymer could be observed even after 20 seconds of treatment. The surface becomes hydrophobic or superhydrophobic, with the water contact angles up to 160 degrees. Morphological changes and increased roughness can be observed only in the nanoscale, whereas the structure seems to be unaffected in the microscale. As a result of plasma modification a permanent hydrophobic effect was obtained on the polyoxymethylene surface.

The Influence of Reduced Graphene Oxide on the Texture and Chemistry of N,S-Doped Porous Carbon. Implications for Electrocatalytic and Energy Storage Applications.

In this work, we study the influence of reduced graphene oxide (rGO) on the morphology and chemistry of highly porous N,S-doped carbon cryogels. Simultaneously, we propose an easily upscalable route to prepare such carbons by adding graphene oxide (GO) in as-received suspended form to the aqueous solution of the ι-carrageenan and urea precursors. First, 1.25-5 wt% GO was incorporated into the dual-doped polymer matrix. The CO2, CO, and H2O emitted during the thermal treatments resulted in the multifaceted modification of the textural and chemical properties of the porous carbon. This facilitated the formation of micropores through self-activation and resulted in a substantial increase in the apparent surface area (up to 1780 m2/g) and pore volume (up to 1.72 cm3/g). However, adding 5 wt% GO led to overactivation. The incorporated rGO has an ordering effect on the carbon matrix. The evolving oxidative species influence the surface chemistry in a complex way, but sufficient N and S atoms (ca. 4 and >1 at%, respectively) were preserved in addition to the large number of developing defects. Despite the complexity of the textural and chemical changes, rGO increased the electrical conductivity monotonically. In alkaline oxygen reduction reaction (ORR) tests, the sample with 1.25 wt% GO exhibited a 4e- mechanism and reasonable stability, but a higher rGO content gradually compromised the performance of the electrodes. The sample containing 5 wt% GO was the most sensitive under oxidative conditions, but after stabilization it exhibited the highest gravimetric capacitance. In Li-ion battery tests, the coulombic efficiency of all the samples was consistently above 98%, indicating the high potential of these carbons for efficient Li-ion insertion and reinsertion during the charge-discharge process, thereby providing a promising alternative for graphite-based anodes. The cell from the 1.25 wt% GO sample showed an initial discharge capacity of 313 mAh/g, 95.1% capacity retention, and 99.3% coulombic efficiency after 50 charge-discharge cycles.

Mobile phase and column chemistry selection for high sensitivity non-targeted LC/ESI/HRMS screening of water.

Systematic selection of mobile phase and column chemistry type can be critical for achieving optimal chromatographic separation, high sensitivity, and low detection limits in liquid chromatography electrospray high resolution mass spectrometry (LC/MS). However, the selection process is challenging for non-targeted screening where the compounds of interest are not preselected nor available for method optimization. To provide general guidance, twenty different mobile phase compositions and four columns were compared for the analysis of 78 compounds with a wide range of physicochemical properties (logP range from -1.46 to 5.48), and analyte sensitivity was compared between methods. The pH, additive type, column, and organic modifier had significant effects on the analyte response factors, and acidic mobile phases (e.g. 0.1% formic acid) yielded highest sensitivity. In some cases, the effect was attributable to the difference in organic modifier content at the time of elution, depending on the mobile phase and column chemistry. Based on these findings, 0.1% formic acid, 0.1% ammonia and 5.0 mM ammonium fluoride were further evaluated for their performance in non-targeted LC/ESI/HRMS analysis of wastewater treatment plan influent and effluent, using a data dependent MS2 acquisition and two different data processing workflows (MS-DIAL, patRoon 2.1) to compare number of detected features and sensitivity. Both data-processing workflows indicated that 0.1% formic acid yielded the highest number of features in full scan spectrum (MS1), as well as the highest number of features that triggered fragmentation spectra (MS2) when dynamic exclusion was used.

First iron(II) organometallic compound acting as ABCB1 inhibitor.

Five new iron (II) complexes bearing imidazole-based (Imi-R) ligands with the general formula [Fe(η5-C5H5)(CO)(PPh3)(Imi-R)][CF3SO3] were synthesized and fully characterized by several spectroscopic and analytical techniques. All compounds crystallize in centrosymmetric space groups in a typical "piano stool" distribution. Given the growing importance of finding alternatives to overcome different forms of multidrug resistance, all compounds were tested against cancer cell lines with different ABCB1 efflux pump expression, namely, the doxorubicin-sensitive (Colo205) and doxorubicin-resistant (Colo320) human colon adenocarcinoma cell lines. Compound 3 bearing 1-benzylimidazole was the most active in both cell lines with IC50 values of 1.26 ± 0.11 and 2.21 ± 0.26 µM, respectively, being also slightly selective against the cancer cells (vs. MRC5 normal human embryonic fibroblast cell lines). This compound, together with compound 2 bearing 1H-1,3-benzodiazole, were found to display very potent ABCB1 inhibitory effect. Compound 3 also showed the ability to induce cell apoptosis. Iron cellular accumulation studies by ICP-MS and ICP-OES methods revealed that the compounds' cytotoxicity is not related to the extent of iron accumulation. Yet, it is worth mentioning that, from the compounds tested, 3 was the only one where iron accumulation was greater in the resistant cell line than in the sensitive one, validating the possible role of ABCB1 inhibition in its mechanism of action.

Immobilization of Metronidazole on Mesoporous Silica Materials.

Metronidazole (MTZ) is a widely used drug, but due to its many side effects, there is a growing trend today to use a minimum dose while maintaining high efficacy. One way to meet this demand is to reduce the size of the drug particles. A relatively new method of size reduction is attaching the drug molecules to a mesoporous carrier. In this paper, we studied the fixation of MTZ molecules on mesoporous silica carriers. The drug was immobilized on two mesoporous silica materials (Syloid, SBA-15) with the use of a variety of immersion techniques and solvents. The immobilized drug was subjected to physicochemical examinations (e.g., SEM, XPS, XRD, nitrogen uptake, DSC) and dissolution studies. A significantly higher immobilization was attained on SBA-15 than on a Syloid carrier. Among the processing parameters, the type of MTZ solvent had the highest influence on immobilization. Ultrasonic agitation had a lower but still significant impact, while the concentration of MTZ in the solution made no difference. Under optimal conditions, with the application of an ethyl acetate solution, the surface coverage on SBA-15 reached as much as 91%. The immobilized MTZ exhibited a ca. 10% faster dissolution rate as compared to the pure micron-sized drug particles.

MultiConditionRT: Predicting liquid chromatography retention time for emerging contaminants for a wide range of eluent compositions and stationary phases.

Structural elucidation of compounds detected with liquid chromatography coupled to high resolution mass spectrometry is a challenging and time-consuming step in the workflow of non-targeted analysis and often requires manual validation of the results. Retention time, alongside exact mass, isotope pattern, fragmentation spectra, and collision cross-section, is valuable information for ruling out unlikely structures and increasing the confidence in others. Different approaches to predict retention times have been used previously for reversed phase chromatography and hydrophilic interaction liquid chromatography (HILIC), but application is limited to a small set of mobile phases and gradient profiles. Here, we expand the toolbox available for retention time predictions by developing a random forest regression model for predicting retention times for four column types and twenty mobile phase systems. MultiConditionRT was built using a dataset containing 78 compounds analyzed with C18 reversed phase, mixed mode, HILIC, and biphenyl columns. In addition, different eluent compositions were used: both methanol and acetonitrile were combined with different aqueous phases with pH from 2.1 to 10.0 (formic acid, acetic acid, trifluoroacetic acid, formate, acetate, bicarbonate, and ammonia). The root mean square error (RMSE) of the test set predictions was 1.55 min for C18 reversed phase, 1.79 min for mixed-mode, 1.93 min for HILIC, and 1.56 min for biphenyl column. Additionally, MultiConditionRT can be applied to different gradient profiles with a general additive model-based calibration approach. The approach of MultiConditionRT was validated externally and internally with 356 and 151 compounds respectively, yielding an RMSE of 2.68 and 2.32 min. 324 and 84 of these compounds were not in the dataset used in the model development.

Construction and Properties of Donor-Acceptor Stenhouse Adducts on Gold Surfaces.

The construction of a donor-acceptor Stenhouse adduct molecular layer on a gold surface is presented. To avoid the incompatibility of the thiol surface-binding group with the donor-acceptor polyene structure of the switch, an interfacial reaction approach was followed. Poly(dopamine)-supported gold nanoparticles on quartz slides were chosen as substrates, which was expected to facilitate both the interfacial reaction and the switching process by providing favorable steric conditions due to the curved particle surface. The reaction between the surface-bound donor half and the CF3-isoxazolone-based acceptor half was proved to be successful by X-ray photoelectron spectroscopy (XPS). However, UV-vis measurements suggested that a closed, cyclopentenone-containing structure of the switch formed on the surface irreversibly. Analysis of the wetting behavior of the surface revealed spontaneous water spreading that could be associated with conformational changes of the closed isomer.

Temperature-Limited Synthesis of Copper Manganites along the Borderline of the Amorphous/Crystalline State and Their Catalytic Activity in CO Oxidation.

Copper manganese oxides (CMO) with CuMn2O4 composition are well-known catalysts, which are widely used for the oxidative removal of dangerous chemicals, e.g., enhancing the CO to CO2 conversion. Their catalytic activity is the highest, close to those of the pre-crystalline and amorphous states. Here we show an easy way to prepare a stable CMO material at the borderline of the amorphous and crystalline state (BAC-CMO) at low temperatures (<100 °C) followed annealing at 300 °C and point out its excellent catalytic activity in CO oxidation reactions. We demonstrate that the temperature-controlled decomposition of [Cu(NH3)4](MnO4)2 in CHCl3 and CCl4 at 61 and 77 °C, respectively, gives rise to the formation of amorphous CMO and NH4NO3, which greatly influences the composition as well as the Cu valence state of the annealed CMOs. Washing with water and annealing at 300 °C result in a BAC-CMO material, whereas the direct annealing of the as-prepared product at 300 °C gives rise to crystalline CuMn2O4 (sCMO, 15-40 nm) and ((Cu,Mn)2O3, bCMO, 35-40 nm) mixture. The annealing temperature influences both the quantity and crystallite size of sCMO and bCMO products. In 0.5% CO/0.5% O2/He mixture the best CO to CO2 conversion rates were achieved at 200 °C with the BAC-CMO sample (0.011 mol CO2/(m2 h)) prepared in CCl4. The activity of this BAC-CMO at 125 °C decreases to half of its original value within 3 h and this activity is almost unchanged during another 20 h. The BAC-CMO catalyst can be regenerated without any loss in its catalytic activity, which provides the possibility for its long-term industrial application.

Metal element alteration in the lung by cisplatin and CV247 administration.

Despite significant nephrotoxicity, cisplatin is still used in the therapy of various tumors. We were interested in how metal ion composition is altered by cisplatin and whether platinum accumulates in the non-tumorous lung. We also aimed to study metal ion changes after treatment with a veterinary medicament CV247 with antioxidant property (containing Cu and Mn gluconate, ascorbic acid, Na salicylate), and whether CV247 alters pulmonary platinum accumulation in the healthy lung. Male Wistar rats were randomly selected into 4 groups (n = 10/group): control group, cisplatin-treated group, CV247-treated group, cisplatin + CV247-treated group. Inductively coupled plasma optical emission spectrometry and mass spectrometry were used for measuring Al, As, B, Ba, Ca, Cd, Co, Cu, Cr, Fe, K, Li, Mg, Mn, Mo, Na, Ni, P, Pb, Pt, S, Sb, Se, Sn, Sr, and Zn in the lung and the redox state was measured in the plasma. Cisplatin influenced the element homeostasis in the lung. Pt, Mn, Se accumulation and Ca, Mg excretion were observed after treatment with cisplatin. The antioxidant CV247 supplementation modified the Mn concentration; however, the concentration of Cu did not change despite the Cu content of the product, and CV247 did not affect other metal concentrations in the lung of the cisplatin-treated group. In conclusion, cisplatin has a systemic impact on the metal element metabolism, and this effect was demonstrated in the healthy lung, too. The results indicate the importance of supplementing some essential elements, such as Ca and Mg during cisplatin cancer therapy.

Photoswitchable Macroscopic Solid Surfaces Based On Azobenzene-Functionalized Polydopamine/Gold Nanoparticle Composite Materials: Formation, Isomerization and Ligand Exchange.

The facile preparation of dynamic interfaces is presented based on the combination of photoisomerizable azobenzenes and polydopamine (PDA)/Au nanoparticle composite materials. Azobenzenes with different spacer lengths (C3 , C6 ) and surface-binding groups (SH, NH2 ) were synthesized. The polymer layer on macroscopic quartz surface was prepared by the facile aerobic autopolymerisation of dopamine hydrochloride under basic conditions. The presence of redox-active catechol moieties meant that gold nanoparticles were formed on the polymer surface. The obtained UV-Vis spectroscopic results confirmed that following their successful assembly, the switching of azobenzenes on PDA/Au was not affected by the surface binding group and the spacer length of the azobenzene molecules under the measurement conditions. Furthermore, facilitated by the curved nature of the Au particles, the surface-bound azobenzene layer could be reconstructed by ligand-exchange processes, and the photochemical characterization of the mixed layer was performed.

Chemical structure and in vitro cellular uptake of luminescent carbon quantum dots prepared by solvothermal and microwave assisted techniques.

Carbon quantum dots (CQDs) are a novel family of fluorescent materials that could be employed as non-toxic alternatives to molecular fluorescent dyes in biological research and also in medicine. Four different preparation approaches, including microwave assisted heating and solvent refluxing, were explored. In addition to the widely used microwave assisted methods, a simple convenient new procedure is presented here for the particle synthesis. A detailed X-ray photoelectron spectroscopic (XPS) analysis was employed to characterize the composition, and more importantly, the chemical structure of the CQD samples and the interrelation of the characteristic surface chemical groups with the fluorescence properties and with surface polarity was unambiguously established. In vitro cellular internalization experiments documented their applicability as fluorescence labels while non-toxic properties were also approved. It was demonstrated that the adequate water-dispersibility of the particles plays a crucial role in their biological application. The synthetized CQD samples turned to be promising for cellular imaging applications both in laser illuminated flow cytometric measurements and in fluorescence microscopy.

Effect of Atmospheric Cold Plasma Treatment on the Adhesion and Tribological Properties of Polyamide 66 and Poly(Tetrafluoroethylene).

The surfaces of two engineering polymers including polyamide 66 (PA66) and polytetrafluoroethylene (PTFE) were treated by diffuse coplanar surface barrier discharges in atmospheric air. We found that plasma treatment improved the adhesion of PA66 for either polymer/polymer or polymer/steel joints, however, it was selective for the investigated adhesive agents. For PTFE the adhesion was unaltered for plasma treatment regardless the type of used adhesive. Tribological properties were slightly improved for PA66, too. Both the friction coefficient and wear decreased. Significant changes, again, could not be detected for PTFE. The occurred variation in the adhesion and tribology was discussed on the basis of the occurred changes in surface chemistry, wettability and topography of the polymer surface.

Unexpected Sequential NH3/H2O Solid/Gas Phase Ligand Exchange and Quasi-Intramolecular Self-Protonation Yield [NH4Cu(OH)MoO4], a Photocatalyst Misidentified before as (NH4)2Cu(MoO4)2.

[NH4Cu(OH)MoO4] as active photocatalyst in the decomposition of Congo Red when irradiated by UV or visible light has been prepared in an unusual ammonia/water ligand exchange reaction of [tetraamminecopper(II)] molybdate, [Cu(NH3)4]MoO4. [Cu(NH3)4]MoO4 was subjected to moisture of open air at room temperature. Light blue orthorhombic [Cu(NH3)(H2O)3]MoO4 was formed in 2 days as a result of an unexpected solid/gas phase ammonia-water ligand exchange reaction. This complex does not lose its last ammonia ligand on further standing in open air; however, a slow quasi-intramolecular (self)-protonation reaction takes place in 2-4 weeks, producing a yellowish-green microcrystalline material, which has been identified as a new compound, [NH4Cu(OH)MoO4], ( a = 10,5306 Å, b = 6.0871 Å, c = 8.0148 Å, ß = 64,153°, C2, Z = 4). Mechanisms are proposed for both the sequential ligand exchange and the self-protonation reactions supported by ab initio quantum-chemical calculations and deuteration experiments as well. The [Cu(NH3)(H2O)3]MoO4 intermediate transforms into NH4Cu(OH)(H2O)2MoO4, which loses two waters and yields [NH4Cu(OH)MoO4]. Upon heating, both [Cu(NH3)4]MoO4 and [Cu(NH3)(H2O)3]MoO4 decompose, losing three NH3 and three H2O ligands, respectively, and stable [Cu(NH3)MoO4] is formed from both. The latter can partially be hydrated in boiling water into [NH4Cu(OH)MoO4. This compound can also be prepared in pure form by boiling the saturated aqueous solution of [Cu(NH3)4]MoO4. All properties of [NH4Cu(OH)MoO4] match those of the active photocatalyst described earlier in the literature under the formulas (NH4)2[Cu(MoO4)2] and (NH4)2Cu4(NH3)3Mo5O20.

Metal- and redox homeostasis in prostate cancer with vitamin D3 supplementation.

Vitamin D3 supplementation has a beneficial effect on cancerous patients, although it can influence the redox- and metal homeostasis. The aim of our investigation was to demonstrate the effect of vitamin D3 consumption on the redox- and metal homeostasis in prostate cancer, because of the recommended daily dose increased from 200 IU to 2000 IU in recent years in Hungary. Forty-three volunteers were involved in the study. The grouping was applied according to the clinical routine laboratory parameters (vitamin D3) and the tumor markers (PSA, fPFA). Patients were divided into 5 groups: (A) patient control (N = 8), (B) patient control with vitamin D3 treatment (N = 9), (C) high-risk prostate cancer group (N = 6), (D) high-risk prostate cancer group with vitamin D3 treatment (N = 8) and (E) vitamin D3 treated cancerous group with androgen deprivation therapy (N = 11). The element concentrations were determined with ICP-OES. Among the redox parameters, free radical scavenging capacity and H-donating ability were determined with luminometry and spectrometry. Vitamin D3 treatment caused differences in the metal- and redox homeostasis in either patient control and cancerous groups. The concentration of Fe, Cr, and Pb significantly increased in the erythrocytes of prostate cancer patients. According to the higher scavenging capacity by vitamin D3 treatment, it seems that vitamin D3 helps to equilibrate the redox homeostasis that could affect the outcome of cancer positively. However, the tendency in the metal element status does not give a clear explanation of cancer's outcome, but the accumulation of Pb by vitamin D3 supplementation needs to be taken into more serious consideration in set terms of occupational diseases.

Improvement of Adhesion Properties of Polyamide 6 and Polyoxymethylene-Copolymer by Atmospheric Cold Plasma Treatment.

A study is presented on cold plasma treatment of the surfaces of two engineering polymers, polyamide 6 (PA6) and polyoxymethylene (POM-C), by diffuse coplanar surface barrier discharges under atmospheric air conditions. We found that plasma treatment improved the adhesion of both polymers for either polymer/polymer or polymer/steel joints. However, the improved adhesion was selective for the investigated adhesive agents that were dissimilar for the two studied polymers. In addition, improvement was significantly higher for PA6 as compared to POM-C. The observed variation of the adhesion was discussed in terms of the changes in surface chemistry, wettability and topography of the polymer surface.