Electrochemical Deposition of Ferromagnetic Ni Nanoparticles in InP Nanotemplates Fabricated by Anodic Etching Using Environmentally Friendly Electrolyte.

Porous InP templates possessing a thickness of up to 100 µm and uniformly distributed porosity were prepared by anodic etching of InP substrates exhibiting different electrical conductivities, involving an environmentally friendly electrolyte. Ni nanoparticles were successfully directly deposited by pulsed electroplating into prefabricated InP templates without any additional deposition of intermediary layers. The parameters of electrodeposition, including the pulse amplitude, pulse width and interval between pulses, were optimized to reach a uniform metal deposition covering the inner surface of the nanopores. The electrochemical dissolution of n-InP single crystals was investigated by measuring the current-voltage dependences, while the Ni-decorated n-InP templates have been characterized by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The proposed technology is expected to be of interest for sensing and photocatalytic applications, as well as for the exploration of their plasmonic and magnetic properties.

The Water-Based Synthesis of Platinum Nanoparticles Using KrF Excimer Laser Ablation.

Our work presents, for the first time, a comprehensive study of the synthesis of fully metallic platinum nanoparticles (Pt-NPs) involving the ablation process in double distilled water using a KrF excimer laser. To obtain detailed information on Pt-NP morphology and optical properties, prepared colloids were characterized using High Resolution Scanning Transmission Electron Microscopy (HR-STEM) with advanced capabilities for Energy Dispersive X-ray Analysis (EDX), UV/Vis optical spectroscopy, and Direct Analysis in Real Time-Mass Spectrometry (DART-MS). The influence of the applied laser fluence and laser repetition rate (RR) values on the characteristics of the obtained Pt-NPs and the ablation process, respectively, were also analyzed. Spherical and spherical-like nanoparticles exhibiting aggregation were produced. The Pt-NP mean size values were between 2.2 ± 1.2 nm and 4.0 ± 1.0 nm, while their interplanar distance measurements showed a face-centered cubic (FFC) Pt lattice (111), as revealed by HR-STEM measurements, for all investigated samples. The smallest mean size of 2.2 nm of the Pt-NPs was obtained using a 2.3 J cm-2 laser fluence at a 10 Hz RR, and the narrowest size distribution of the NPs was obtained with a 2.3 J cm-2 laser fluence at a 40 Hz RR. A linear dependence of the Pt-NP diameters versus the laser repetition rate was found at a constant fluence of 2.3 J cm-2. The proposed eco-friendly synthesis route of Pt-NPs, because of its relative simplicity, has the potential for use in industrial production.

Pulsed Laser Deposition of SWCNTs on Carbon Fibres: Effect of Deposition Temperature.

Single wall carbon nanotubes (SWCNTs) were grown on either sized or desized carbon fabric in a self-designed reactor by Pulsed Laser Deposition (PLD). The uniqueness of the PLD system lies, among other things, in the ability to keep the substrate at a low temperature, compared to the 1100 °C needed for the SWCNTs synthesis, thus, rendering it undamaged. Samples were placed at different positions on a cold finger (CF), where a temperature gradient develops, in the range 25-565 °C. The chemical composition and morphology of desized and surface treatments, as well as SWCNTs grown on carbon fibres, were verified by Scanning Electron Microscopy (SEM) equipped with Energy Dispersive X-Ray Spectroscopy (EDX), while the quality of SWCNTs was proven by confocal micro-Raman Spectroscopy and High-Resolution Scanning Transmission Electron Microscopy (HR-STEM). Fibres covered with SWCNTs by PLD were characterized using contact angle and the surface free energy was calculated. A micro-droplet pull-out test was used to evaluate the effect of SWCNTs over interfacial properties of a carbon-epoxy composite. A 20% increase in interfacial shear strength (IFSS) was observed by deposition at 290 °C, compared to the commercial carbon fibre sizing. The carbon fibres kept their tensile properties due to the low deposition temperatures.

Eco-Friendly Push-Coated Polymer Solar Cells with No Active Material Wastes Yield Power Conversion Efficiencies over 5.5.

Push-coating is a simple process that can be employed for extremely low-cost polymer electronic device production. Here, we demonstrate its application to the fabrication of poly(2,7-carbazole- alt-dithienylbenzothiadiazole) (PCDTBT):[6,6]-phenyl-C71-butyric acid methyl ester (PC71BM) active layers processed in air, yielding similar photovoltaic performances as thermally annealed spin-coated thin films when used in inverted polymer solar cells (PSCs). During push-coating, the polydimethylsiloxane layer temporarily traps the deposition solvent, resulting in simultaneous film formation and solvent annealing effect. This removes the necessity for a postdeposition thermal annealing step which is required for spin-coated PSCs to produce high photovoltaic performances. Optimized PSC active layers are produced with a push-coating time of 5 min at room temperature with 20 times less hazardous solvent and 40 times less active material than spin-coating. Annealed spin-coated active layers and active layers push-coated for 5 min both produce average power conversion efficiencies (PCEs) of 5.77%, while those push-coated for a shorter time of 1 min yield a slightly lower value of 5.59%. We demonstrate that, despite differences in their donor:acceptor vertical concentration gradients, unencapsulated PCDTBT:PC71BM active layers push-coated for 1 min produce PSCs with similar operational stability and upscaling capacity as thermally annealed spin-coated ones. As fast device fabrication can be achieved with short-time push-coating, we further demonstrate the potential of this deposition technique by manufacturing push-coated PSC-based semitransparent photovoltaic devices with a PCE of 4.23%, relatively neutral colors and an average visible transparency of 40.2%. Our work thus confirms that push-coating is not limited to the widely employed poly(3-hexylthiophene-2,5-diyl) but can also be used with low band gap copolymers and opens the path to low-cost and eco-friendly, yet efficient and stable PSCs.

A Molecular Pillar Approach To Grow Vertical Covalent Organic Framework Nanosheets on Graphene: Hybrid Materials for Energy Storage.

Hybrid 2D-2D materials composed of perpendicularly oriented covalent organic frameworks (COFs) and graphene were prepared and tested for energy storage applications. Diboronic acid molecules covalently attached to graphene oxide (GO) were used as nucleation sites for directing vertical growth of COF-1 nanosheets (v-COF-GO). The hybrid material has a forest of COF-1 nanosheets with a thickness of 3 to 15 nm in edge-on orientation relative to GO. The reaction performed without molecular pillars resulted in uncontrollable growth of thick COF-1 platelets parallel to the surface of GO. The v-COF-GO was converted into a conductive carbon material preserving the nanostructure of precursor with ultrathin porous carbon nanosheets grafted to graphene in edge-on orientation. It was demonstrated as a high-performance electrode material for supercapacitors. The molecular pillar approach can be used for preparation of many other 2D-2D materials with control of their relative orientation.