A Universal Perovskite/C60 Interface Modification via Atomic Layer Deposited Aluminum Oxide for Perovskite Solar Cells and Perovskite-Silicon Tandems.

The primary performance limitation in inverted perovskite-based solar cells is the interface between the fullerene-based electron transport layers and the perovskite. Atomic layer deposited thin aluminum oxide (AlOX) interlayers that reduce nonradiative recombination at the perovskite/C60 interface are developed, resulting in >60 millivolts improvement in open-circuit voltage and 1% absolute improvement in power conversion efficiency. Surface-sensitive characterizations indicate the presence of a thin, conformally deposited AlOx layer, functioning as a passivating contact. These interlayers work universally using different lead-halide-based absorbers with different compositions where the 1.55 electron volts bandgap single junction devices reach >23% power conversion efficiency. A reduction of metallic Pb0 is found and the compact layer prevents in- and egress of volatile species, synergistically improving the stability. AlOX-modified wide-bandgap perovskite absorbers as a top cell in a monolithic perovskite-silicon tandem enable a certified power conversion efficiency of 29.9% and open-circuit voltages above 1.92 volts for 1.17 square centimeters device area.

Long-Term Safety Profiles of Macrolides and Tetracyclines: A Systematic Review and Meta-Analysis.

Macrolides and tetracyclines are antibiotics that have a range of anti-inflammatory properties beyond their microbial capabilities. Although these antibiotics have been in widespread use, the long-term safety profiles are limited. We performed a systematic review and meta-analysis of randomized clinical trials that compared macrolides or tetracyclines with placeboes to provide long-term safety information. We searched Medline and EMBASE from inception to October 2022 and identified studies that reported study drug-related death, serious adverse events (SAEs), or withdrawal rates, and common adverse effects of each drug. Relative risk (RR) and number needed to harm were calculated. Of the 52 randomized clinical trials included, there are 3151 participants on doxycycline, 2519 participants on minocycline, 3049 participants on azithromycin, 763 participants on clarithromycin, 262 participants on erythromycin, and 100 participants on roxithromycin. There was no death related to any study drugs and rates of SAE were not significantly different from placebo in any drug. Overall withdrawal rates were slightly higher than placebo in doxycycline (RR, 1.30; 95% CI, 1.12-1.52) and minocycline (RR, 1.29; 95% CI, 1.15-1.46). Withdrawal rates due to adverse events were higher in doxycycline (RR, 2.82; 95% CI, 1.88-4.22), minocycline (RR, 1.48; 95% CI, 1.09-1.98), and azithromycin (RR, 1.53; 95% CI, 1.13-2.08). Gastrointestinal disturbances are the most common tolerable adverse effects for every drug. Photosensitivity and rash are the second most common adverse effects for doxycycline and minocycline. We found no evidence that long-term use up to 2 years of macrolides or tetracyclines was associated with increased risk of SAEs.

Rear textured p-type high temperature passivating contacts and their implementation in perovskite/silicon tandem cells.

Silicon solar cells based on high temperature passivating contacts are becoming mainstream in the photovoltaic industry. Here, we developed a high-quality boron-doped poly-silicon hole contact. When combined with a co-processed phosphorus-doped poly-silicon electron contact, high-voltage silicon bottom cells could be demonstrated and included in 28.25%-efficient perovskite/Si tandems. The active area was 4 cm2 active area and the front electrode was screen-printed.

Understanding and Mitigating the Degradation of Perovskite Solar Cells Based on a Nickel Oxide Hole Transport Material during Damp Heat Testing.

The development of stable materials, processable on a large area, is a prerequisite for perovskite industrialization. Beyond the perovskite absorber itself, this should also guide the development of all other layers in the solar cell. In this regard, the use of NiOx as a hole transport material (HTM) offers several advantages, as it can be deposited with high throughput on large areas and on flat or textured surfaces via sputtering, a well-established industrial method. However, NiOx may trigger the degradation of perovskite solar cells (PSCs) when exposed to environmental stressors. Already after 100 h of damp heat stressing, a strong fill factor (FF) loss appears in conjunction with a characteristic S-shaped J-V curve. By performing a wide range of analysis on cells and materials, completed by device simulation, the cause of the degradation is pinpointed and mitigation strategies are proposed. When NiOx is heated in an air-tight environment, its free charge carrier density drops, resulting in a band misalignment at the NiOx/perovskite interface and in the formation of a barrier impeding hole extraction. Adding an organic layer between the NiOx and the perovskite enables higher performances but not long-term thermal stability, for which reducing the NiOx thickness is necessary.

IL-17 Induced Stromal Cell-Derived Factor-1 and Profibrotic Factor in Keloid-Derived Skin Fibroblasts via the STAT3 Pathway.

The pathogenesis of keloids has not been elucidated, and the disease is thought to be caused by abnormal secretion of proinflammatory mediators and irregular responses to other inflammatory signals mediated by keloid fibroblasts (KFs). In this study, we investigated whether a local increase in interleukin IL-17 in keloid tissues stimulates the production of stromal cell-derived factor-1 (SDF-1) in KFs causing further recruitment of IL-17-producing T helper 17 (Th17) cells, which subsequently creates a positive feedback loop. Histological assessment was performed and the change in the expression of IL-17, IL-1ß, IL-6, and TNF-α which of fibrosis and inflammation associated markers was examined. In addition, fibroblasts were treated with IL-17 in the presence or absence of STAT3 inhibitor STA-21; SDF-1 levels and fibrosis genes were measured. Our results showed that fibrotic reaction and expression of proinflammatory cytokines including IL-17 were most prominent in the growing margin (perilesional area) of keloid tissue and Th17 cells significantly infiltrated the perilesional area. In addition, IL-17 upregulated the expression of SDF-1, collagen, and α-SMA in KFs. Finally, STA-21 decreased SDF-1α expression and the expression of fibrosis genes in KFs even after IL-17 stimulation. Our study demonstrated that a local increase in IL-17 in keloid tissues stimulates the production of SDF-1 in KFs causing further recruitment of IL-17-producing T helper 17 (Th17) cells, which subsequently creates a positive feedback loop. These findings suggest that STAT3 inhibition can be used to treat keloid scars by reversing the vicious cycle between Th17 cells and KFs.

Complex Refractive Index Spectra of CH3NH3PbI3 Perovskite Thin Films Determined by Spectroscopic Ellipsometry and Spectrophotometry.

The complex refractive index (dielectric function) of planar CH3NH3PbI3 thin films at room temperature is investigated by variable angle spectroscopic ellipsometry and spectrophotometry. Knowledge of the complex refractive index is essential for designing photonic devices based on CH3NH3PbI3 thin films such as solar cells, light-emitting diodes, or lasers. Because the directly measured quantities (reflectance, transmittance, and ellipsometric spectra) are inherently affected by multiple reflections, the complex refractive index has to be determined indirectly by fitting a model dielectric function to the experimental spectra. We model the dielectric function according to the Forouhi-Bloomer formulation with oscillators positioned at 1.597, 2.418, and 3.392 eV and achieve excellent agreement with the experimental spectra. Our results agree well with previously reported data of the absorption coefficient and are consistent with Kramers-Kronig transformations. The real part of the refractive index assumes a value of 2.611 at 633 nm, implying that CH3NH3PbI3-based solar cells are ideally suited for the top cell in monolithic silicon-based tandem solar cells.

Raman Spectroscopy of Organic-Inorganic Halide Perovskites.

Micro-Raman spectroscopy provides laterally resolved microstructural information for a broad range of materials. In this Letter, we apply this technique to tri-iodide (CH3NH3PbI3), tribromide (CH3NH3PbBr3), and mixed iodide-bromide (CH3NH3PbI3-xBrx) organic-inorganic halide perovskite thin films and discuss necessary conditions to obtain reliable data. We explain how to measure Raman spectra of pristine CH3NH3PbI3 layers and discuss the distinct Raman bands that develop during moisture-induced degradation. We also prove unambiguously that the final degradation products contain pure PbI2. Moreover, we describe CH3NH3PbI3-xBrx Raman spectra and discuss how the perovskite crystallographic symmetries affect the Raman band intensities and spectral shapes. On the basis of the dependence of the Raman shift on the iodide-to-bromide ratio, we show that Raman spectroscopy is a fast and nondestructive method for the evaluation of the relative iodide-to-bromide ratio.

Organic-inorganic halide perovskite/crystalline silicon four-terminal tandem solar cells.

Tandem solar cells constructed from a crystalline silicon (c-Si) bottom cell and a low-cost top cell offer a promising way to ensure long-term price reductions of photovoltaic modules. We present a four-terminal tandem solar cell consisting of a methyl ammonium lead triiodide (CH3NH3PbI3) top cell and a c-Si heterojunction bottom cell. The CH3NH3PbI3 top cell exhibits broad-band transparency owing to its design free of metallic components and yields a transmittance of >55% in the near-infrared spectral region. This allows the generation of a short-circuit current density of 13.7 mA cm(-2) in the bottom cell. The four-terminal tandem solar cell yields an efficiency of 13.4% (top cell: 6.2%, bottom cell: 7.2%), which is a gain of 1.8%abs with respect to the reference single-junction CH3NH3PbI3 solar cell with metal back contact. We employ the four-terminal tandem solar cell for a detailed investigation of the optical losses and to derive guidelines for further efficiency improvements. Based on a power loss analysis, we estimate that tandem efficiencies of ∼28% are attainable using an optically optimized system based on current technology, whereas a fully optimized, ultimate device with matched current could yield up to 31.6%.

Organometallic Halide Perovskites: Sharp Optical Absorption Edge and Its Relation to Photovoltaic Performance.

Solar cells based on organometallic halide perovskite absorber layers are emerging as a high-performance photovoltaic technology. Using highly sensitive photothermal deflection and photocurrent spectroscopy, we measure the absorption spectrum of CH3NH3PbI3 perovskite thin films at room temperature. We find a high absorption coefficient with particularly sharp onset. Below the bandgap, the absorption is exponential over more than four decades with an Urbach energy as small as 15 meV, which suggests a well-ordered microstructure. No deep states are found down to the detection limit of ∼1 cm(-1). These results confirm the excellent electronic properties of perovskite thin films, enabling the very high open-circuit voltages reported for perovskite solar cells. Following intentional moisture ingress, we find that the absorption at photon energies below 2.4 eV is strongly reduced, pointing to a compositional change of the material.

4,9-Dihydro-4,4,9,9-tetrahexyl-s-indaceno[1,2-b:5,6-b']dithiophene as a π-spacer of donor-π-acceptor dye and its photovoltaic performance with liquid and solid-state dye-sensitized solar cells.

A new D-π-A organic dye, LC-5, containing 4,9-dihydro-4,4,9,9-tetrahexyl-s-indaceno[1,2-b:5,6-b']-dithiophene as a novel π-conjugated spacer has been synthesized and tested as a sensitizer in dye-sensitized solar cells (DSC). Volatile and ionic liquid electrolytes have been used in conjunction with the synthesized dye, and the electrolyte influence on the photovoltaic performance of DSCs was investigated. A detailed investigation, including transient photocurrent/photovoltage decay measurements and electrochemical impedance spectroscopy data, provide important conclusions about the influence of electrolytes on the photovoltaic parameters.

Sequential deposition as a route to high-performance perovskite-sensitized solar cells.

Following pioneering work, solution-processable organic-inorganic hybrid perovskites-such as CH3NH3PbX3 (X = Cl, Br, I)-have attracted attention as light-harvesting materials for mesoscopic solar cells. So far, the perovskite pigment has been deposited in a single step onto mesoporous metal oxide films using a mixture of PbX2 and CH3NH3X in a common solvent. However, the uncontrolled precipitation of the perovskite produces large morphological variations, resulting in a wide spread of photovoltaic performance in the resulting devices, which hampers the prospects for practical applications. Here we describe a sequential deposition method for the formation of the perovskite pigment within the porous metal oxide film. PbI2 is first introduced from solution into a nanoporous titanium dioxide film and subsequently transformed into the perovskite by exposing it to a solution of CH3NH3I. We find that the conversion occurs within the nanoporous host as soon as the two components come into contact, permitting much better control over the perovskite morphology than is possible with the previously employed route. Using this technique for the fabrication of solid-state mesoscopic solar cells greatly increases the reproducibility of their performance and allows us to achieve a power conversion efficiency of approximately 15 per cent (measured under standard AM1.5G test conditions on solar zenith angle, solar light intensity and cell temperature). This two-step method should provide new opportunities for the fabrication of solution-processed photovoltaic cells with unprecedented power conversion efficiencies and high stability equal to or even greater than those of today's best thin-film photovoltaic devices.

Lead iodide perovskite sensitized all-solid-state submicron thin film mesoscopic solar cell with efficiency exceeding 9%.

We report on solid-state mesoscopic heterojunction solar cells employing nanoparticles (NPs) of methyl ammonium lead iodide (CH(3)NH(3))PbI(3) as light harvesters. The perovskite NPs were produced by reaction of methylammonium iodide with PbI(2) and deposited onto a submicron-thick mesoscopic TiO(2) film, whose pores were infiltrated with the hole-conductor spiro-MeOTAD. Illumination with standard AM-1.5 sunlight generated large photocurrents (J(SC)) exceeding 17 mA/cm(2), an open circuit photovoltage (V(OC)) of 0.888 V and a fill factor (FF) of 0.62 yielding a power conversion efficiency (PCE) of 9.7%, the highest reported to date for such cells. Femto second laser studies combined with photo-induced absorption measurements showed charge separation to proceed via hole injection from the excited (CH(3)NH(3))PbI(3) NPs into the spiro-MeOTAD followed by electron transfer to the mesoscopic TiO(2) film. The use of a solid hole conductor dramatically improved the device stability compared to (CH(3)NH(3))PbI(3) -sensitized liquid junction cells.

The p53-reactivating small-molecule RITA enhances cisplatin-induced cytotoxicity and apoptosis in head and neck cancer.

We evaluated whether the restoration of p53 function by the p53-reactivating small molecule RITA (reactivation of p53 and induction of tumor cell apoptosis enhances cisplatin-induced cytotoxicity and apoptosis in head-and-neck cancer (HNC). RITA induced prominent accumulation and reactivation of p53 in a wild-type TP53-bearing HNC cell line. RITA showed maximal growth suppression in tumor cells showing MDM2-dependent p53 degradation. RITA promoted apoptosis in association with upregulation of p21, BAX, and cleaved caspase-3; notably, the apoptotic response was blocked by pifithrin-α, demonstrating its p53 dependence. With increasing concentrations, RITA strongly induced apoptosis rather than G2-phase arrest. In combination therapy, RITA enhanced cisplatin-induced growth inhibition and apoptosis of HNC cells invitro and in vivo. Our data suggest that the restoration of p53 tumor-suppressive function by RITA enhances the cytotoxicity and apoptosis of cisplatin, an action that may offer an attractive strategy for treating HNC.

Enhanced light harvesting in mesoporous TiO2/P3HT hybrid solar cells using a porphyrin dye.

We report panchromatic light harvesting in hybrid TiO(2)/P3HT photovoltaic devices using a porphyrin dye that complements the light absorption of P3HT. The high short circuit photocurrent (12.1 mA cm(-2)) obtained is found to be due, in part, to Förster resonance energy transfer from the P3HT to the dye.

An organic D-π-A dye for record efficiency solid-state sensitized heterojunction solar cells.

The high molar absorption coefficient organic D-π-A dye C220 exhibits more than 6% certified electric power conversion efficiency at AM 1.5G solar irradiation (100 mW cm(-2)) in a solid-state dye-sensitized solar cell using 2,2',7,7'-tetrakis(N,N-dimethoxyphenylamine)-9,9'-spirobifluorene (spiro-MeOTAD) as the organic hole-transporting material. This contributes to a new record (6.08% by NREL) for this type of sensitized heterojunction photovoltaic device. Efficient charge generation is proved by incident photon-to-current conversion efficiency spectra. Transient photovoltage and photocurrent decay measurements showed that the enhanced performance achieved with C220 partially stems from the high charge collection efficiency over a wide potential range.

Colorimetric pH measurement of animal cell culture media.

Most animal cell culture media can be buffered using bicarbonate and high pressure CO(2) in a closed system. However, in an open system, the pH of the culture media increases continuously due to the marked difference in CO(2) pressure between the culture media and the atmosphere. Therefore, it is important to measure the exact pH of the culture media in an intact closed system. In this study, a pH measurement method was developed using visible light. The pH was calculated from light absorbance by the cells and by the culture media. This method was successfully applied to both suspension and anchorage-dependent cell cultures.

Efficient and stable solid-state dye-sensitized solar cells based on a high-molar-extinction-coefficient sensitizer.

The high-molar-extinction-coefficient heteroleptic ruthenium dye, cis-Ru (4,4'-bis(5-octylthieno[3,2-b] thiophen-2-yl)-2,2'-bipyridine) (4,4'-dicarboxyl-2,2'-bipyridine) (NCS)(2), exhibits an AM 1.5 solar (100 mW cm(-2))-to-electric power-conversion efficiency of 4.6% in a solid-state dye-sensitized solar cell (SSDSC) with 2,2', 7,7'-tetrakis-(N,N-di-p-methoxyphenylamine)9,9'-spirobifluorene (spiro-MeOTAD) as the organic hole-transporting material. These SSDSC devices exhibit good durability during accelerated tests under visible-light soaking for 1000 h at 60 degrees C. This demonstration elucidates a class of photovoltaic devices with potential for stable and low-cost power generation. The electron recombination dynamics and charge collection that take place at the dye-sensitized heterojunction are studied by means of impedance and transient photovoltage decay techniques.

Regenerative PbS and CdS quantum dot sensitized solar cells with a cobalt complex as hole mediator.

Metal sulfide (PbS and CdS) quantum dots (QDs) were prepared over mesoporous TiO2 films by improved successive ionic layer adsorption and reaction (SILAR) processes. The as-prepared QD-sensitized electrodes were combined with a cobalt complex redox couple [Co(o-phen)3]2+/3+ to make a regenerative liquid-type photovoltaic cell. The optimized PbS QD-sensitized solar cells exhibited promising incident photon-to-current conversion efficiency (IPCE) of over 50% and an overall conversion efficiency of 2% at 0.1 sun in a regenerative mode. The overall photovoltaic performance of the PbS QD-sensitized cells was observed to be dependent on the final turn of the SILAR process, giving a better result when the final deposition was Pb2+, not S2-. However, in the case of CdS QD-sensitized cells, S2- termination was better than that of Cd2+. The cobalt complex herein used as a regenerative redox couple was found to be more efficient in generating photocurrents from PbS QD cells than the typical hole scavenger Na2S in a three-electrode configuration. The CdS-sensitized cell with this redox mediator also showed better defined current-voltage curves and an IPCE reaching 40%.

High open-circuit voltage solid-state dye-sensitized solar cells with organic dye.

Solid-state dye-sensitized solar cells were fabricated using an organic dye, 2-cyanoacrylic acid-4-(bis-dimethylfluoreneaniline)dithiophene (JK2), which exhibits more than 1 V open-circuit potential (V(oc)). To scrutinize the origin of high voltage in these cells, transient V(oc) decay measurements and density functional theroy calculations of the interacting dye/semiconductor surface were performed. A negative conduction band shift was observed due to the favorable dipolar field exerted by the JK2 sensitizer to the TiO(2) surface, at variance with heteroleptic Ru(II)-dyes for which an opposite dipole effect was found, providing an increased V(oc).