Iron(III) cross-linked hydrogels based on Alteromonas macleodii Mo 169 exopolysaccharide.

Recently, polysaccharide-based hydrogels crosslinked with the trivalent iron cation have attracted interest due to their remarkable properties that include high mechanical stability, stimuli-responsiveness, and enhanced absorptivity. In this study, a Fe3+ crosslinked hydrogel was prepared using the biocompatible extracellular polysaccharide (EPS) secreted by the marine bacterium Alteromonas macleodii Mo169. Hydrogels with mechanical strengths (G') ranging from 0.3 kPa to 44.5 kPa were obtained as a result of the combination of different Fe3+ (0.05-9.95 g L-1) and EPS (0.3-1.7 %) concentrations. All the hydrogels had a water content above 98 %. Three different hydrogels, named HA, HB, and HC, were chosen for further characterization. With strength values (G') of 3.2, 28.9, and 44.5 kPa, respectively, these hydrogels might meet the strength requirements for several specific applications. Their mechanical resistance increased as higher Fe3+ and polymer concentrations were used in their preparation (the compressive hardness increased from 8.7 to 192.1 kPa for hydrogel HA and HC, respectively). In addition, a tighter mesh was noticed for HC, which was correlated to its lower swelling ratio value compared to HA and HB. Overall, this preliminary study highlighted the potential of these hydrogels for tissue engineering, drug delivery, or wound healing applications.

Elevated fucose content enhances the cryoprotective performance of anionic polysaccharides.

Biological cryopreservation often involves using a cryoprotective agent (CPA) to mitigate lethal physical stressors cells endure during freezing and thawing, but effective CPA concentrations are cytotoxic. Hence, natural polysaccharides have been studied as biocompatible alternatives. Here, a subset of 26 natural polysaccharides of various chemical composition was probed for their potential in enhancing the metabolic post-thaw viability (PTV) of cryopreserved Vero cells. The best performing cryoprotective polysaccharides contained significant fucose amounts, resulting in average PTV 2.8-fold (up to 3.1-fold) compared to 0.8-fold and 2.2-fold for all non-cryoprotective and cryoprotective polysaccharides, respectively, outperforming the optimized commercial CryoStor™ CS5 formulation (2.6-fold). Stoichiometrically, a balance between fucose (18-35.7 mol%), uronic acids (UA) (13.5-26 mol%) and high molecular weight (MW > 1 MDa) generated optimal PTV. Principal component analysis (PCA) revealed that fucose enhances cell survival by a charge-independent, MW-scaling mechanism (PC1), drastically different from the charge-dominated ice growth disruption of UA (PC2). Its neutral nature and unique properties distinguishable from other neutral monomers suggest fucose may play a passive role in conformational adaptability of polysaccharide to ice growth inhibition, or an active role in cell membrane stabilization through binding. Ultimately, fucose-rich anionic polysaccharides may indulge in polymer-ice and polymer-cell interactions that actively disrupt ice and minimize lethal volumetric fluctuations due to a balanced hydrophobic-hydrophilic character. Our research showed the critical role neutral fucose plays in enhancing cellular cryopreservation outcomes, disputing previous assumptions of polyanionicity being the sole governing predictor of cryoprotection.

Selenium Bio-Nanocomposite Based on Alteromonas macleodii Mo169 Exopolysaccharide: Synthesis, Characterization, and In Vitro Antioxidant Activity.

In this study, the novel exopolysaccharide (EPS) produced by the marine bacterium Alteromonas macleodii Mo 169 was used as a stabilizer and capping agent in the preparation of selenium nanoparticles (SeNPs). The synthesized nanoparticles were well dispersed and spherical with an average particle size of 32 nm. The cytotoxicity of the EPS and the EPS/SeNPs bio-nanocomposite was investigated on human keratinocyte (HaCaT) and fibroblast (CCD-1079Sk) cell lines. No cytotoxicity was found for the EPS alone for concentrations up to 1 g L-1. A cytotoxic effect was only noticed for the bio-nanocomposite at the highest concentrations tested (0.5 and 1 g L-1). In vitro experiments demonstrated that non-cytotoxic concentrations of the EPS/SeNPs bio-nanocomposite had a significant cellular antioxidant effect on the HaCaT cell line by reducing ROS levels up to 33.8%. These findings demonstrated that the A. macleodii Mo 169 EPS can be efficiently used as a stabilizer and surface coating to produce a SeNP-based bio-nanocomposite with improved antioxidant activity.

Rheological characterization of the exopolysaccharide produced by Alteromonas macleodii Mo 169.

Rheology modifiers are essential additives in numerous products in a variety of industries. Due to environmental awareness, consumer-oriented industries are interested in novel natural rheological agents that can replace synthetic chemicals. In this study, the chemical composition and rheological properties of a novel exopolysaccharide (EPS) produced by Alteromonas macleodii Mo 169 were investigated. It was mainly composed of uronic acids (50 mol%) and total carbohydrates were 17 % sulfated. The EPS viscosity increased with concentration, and a non-Newtonian shear thinning behavior was found for concentrations above 0.1 wt%. The elastic and viscous moduli indicated a weak gel-like structure above 0.4 wt%. It maintained its shear thinning behavior and viscoelastic properties in the presence of NaCl and CaCl2 for pH range 5-7 and temperatures up to 55 °C. Though the apparent viscosity decreased at pH 3 and 9 and temperatures above 65 °C, the shear thinning behavior was retained. The viscous and viscoelastic properties were recovered after heating (95 °C) and cooling (0 °C), indicating a good thermal stability and recoverability. After high shear force, the solution recovered original rheological properties within few seconds, demonstrating self-healing properties.

Anti-Biofilm Activity of a Hyaluronan-like Exopolysaccharide from the Marine Vibrio MO245 against Pathogenic Bacteria.

Biofilms, responsible for many serious drawbacks in the medical and marine environment, can grow on abiotic and biotic surfaces. Commercial anti-biofilm solutions, based on the use of biocides, are available but their use increases the risk of antibiotic resistance and environmental pollution in marine industries. There is an urgent need to work on the development of ecofriendly solutions, formulated without biocidal agents, that rely on the anti-adhesive physico-chemical properties of their materials. In this context, exopolysaccharides (EPSs) are natural biopolymers with complex properties than may be used as anti-adhesive agents. This study is focused on the effect of the EPS MO245, a hyaluronic acid-like polysaccharide, on the growth, adhesion, biofilm maturation, and dispersion of two pathogenic model strains, Pseudomonas aeruginosa sp. PaO1 and Vibrio harveyi DSM19623. Our results demonstrated that MO245 may limit biofilm formation, with a biofilm inhibition between 20 and 50%, without any biocidal activity. Since EPSs have no significant impact on the bacterial motility and quorum sensing factors, our results indicate that physico-chemical interactions between the bacteria and the surfaces are modified due to the presence of an adsorbed EPS layer acting as a non-adsorbing layer.

Characterisation of Films Based on Exopolysaccharides from Alteromonas Strains Isolated from French Polynesia Marine Environments.

This work assessed the film-forming capacity of exopolysaccharides (EPS) produced by six Alteromonas strains recently isolated from different marine environments in French Polynesia atolls. The films were transparent and resulted in small colour alterations when applied over a coloured surface (ΔEab below 12.6 in the five different colours tested). Moreover, scanning electron microscopy showed that the EPS films were dense and compact, with a smooth surface. High water vapour permeabilities were observed (2.7-6.1 × 10-11 mol m-1 s-1 Pa-1), which are characteristic of hydrophilic polysaccharide films. The films were also characterised in terms of barrier properties to oxygen and carbon dioxide. Interestingly, different behaviours in terms of their mechanical properties under tensile tests were observed: three of the EPS films were ductile with high elongation at break (ε) (35.6-47.0%), low tensile strength at break (Ꞇ) (4.55-11.7 MPa) and low Young's modulus (εm) (10-93 MPa), whereas the other three were stiffer and more resistant with a higher Ꞇ (16.6-23.6 MPa), lower ε (2.80-5.58%), and higher εm (597-1100 MPa). These properties demonstrate the potential of Alteromonas sp. EPS films to be applied in different areas such as biomedicine, pharmaceuticals, or food packaging.

Characterization and Biotechnological Potential of Extracellular Polysaccharides Synthesized by Alteromonas Strains Isolated from French Polynesia Marine Environments.

Marine environments comprise almost three quarters of Earth's surface, representing the largest ecosystem of our planet. The vast ecological and metabolic diversity found in marine microorganisms suggest that these marine resources have a huge potential as sources of novel commercially appealing biomolecules, such as exopolysaccharides (EPS). Six Alteromonas strains from different marine environments in French Polynesia atolls were selected for EPS extraction. All the EPS were heteropolysaccharides composed of different monomers, including neutral monosaccharides (glucose, galactose, and mannose, rhamnose and fucose), and uronic acids (glucuronic acid and galacturonic acid), which accounted for up to 45.5 mol% of the EPS compositions. Non-carbohydrate substituents, such as acetyl (0.5-2.1 wt%), pyruvyl (0.2-4.9 wt%), succinyl (1-1.8 wt%), and sulfate (1.98-3.43 wt%); and few peptides (1.72-6.77 wt%) were also detected. Thermal analysis demonstrated that the EPS had a degradation temperature above 260 °C, and high char yields (32-53%). Studies on EPS functional properties revealed that they produce viscous aqueous solutions with a shear thinning behavior and could form strong gels in two distinct ways: by the addition of Fe2+, or in the presence of Mg2+, Cu2+, or Ca2+ under alkaline conditions. Thus, these EPS could be versatile materials for different applications.

Solid-Phase Extraction Embedded Dialysis (SPEED), an Innovative Procedure for the Investigation of Microbial Specialized Metabolites.

Solid-phase extraction embedded dialysis (SPEED technology) is an innovative procedure developed to physically separate in-situ, during the cultivation, the mycelium of filament forming microorganisms, such as actinomycetes and fungi, and the XAD-16 resin used to trap the secreted specialized metabolites. SPEED consists of an external nylon cloth and an internal dialysis tube containing the XAD resin. The dialysis barrier selects the molecular weight of the trapped compounds, and prevents the aggregation of biomass or macromolecules on the XAD beads. The external nylon promotes the formation of a microbial biofilm, making SPEED a biofilm supported cultivation process. SPEED technology was applied to the marine Streptomyces albidoflavus 19-S21, isolated from a core of a submerged Kopara sampled at 20 m from the border of a saltwater pond. The chemical space of this strain was investigated effectively using a dereplication strategy based on molecular networking and in-depth chemical analysis. The results highlight the impact of culture support on the molecular profile of Streptomyces albidoflavus 19-S21 secondary metabolites.

Structure, rheology, and copper-complexation of a hyaluronan-like exopolysaccharide from Vibrio.

MO245 exopolysaccharide (EPS) was produced in laboratory conditions from Vibrio genus microorganism isolated from bacterial mats found in Moorea Island. Its structure consists of a linear tetrasaccharide repeating unit →4)-ß-D-GlcpA-(1→4)-α-D-GalpNAc-(1→3)-ß-D-GlcpNAc-(1→4)-ß-D-GlcpA-(1→ containing covalently-linked 5% of glucose, galactose, and rhamnose, determined by methylation analyses and NMR spectroscopy. The molecular weight, radius of gyration (Rg) and intrinsic viscosity, [η], determined by gel permeation chromatography with light scattering and viscosity detection, were 513 ± 4 kDa (PDI, 1.42 ± 0.01), 6.7 ± 0.3 dl/g and 56 ± 0.3 nm respectively. The chelation of the EPS with copper divalent ions leads to the instantaneous formation of gels. The structural similitude proposed, based in an equal ratio of GlcA to N-acetylated sugars and in the same type of glyosidic linkages present in the repeating unit (alternated 1→3 and 1→4 linkages), is translated into analogous physicochemical properties: MO245 EPS is a flexible polyelectrolyte, with scaling exponents similar to that described for HA. This similitude opens opportunities in future drug delivery, tissue engineering, and cosmetic applications.

Investigations into the uptake of copper, iron and selenium by a highly sulphated bacterial exopolysaccharide isolated from microbial mats.

A bacterium isolated from microbial mats located on a polynesian atoll produced a high molecular weight (3,000 kDa) and highly sulphated exopolysaccharide. Previous studies showed that the chemical structure of this EPS consisted of neutral sugars, uronic acids, and high proportions of acetate and sulphate groups. The copper- and iron-binding ability of the purified pre-treated native EPS was investigated. Results showed that this EPS had a very high affinity for both copper (9.84 mmol g(-1) EPS) and ferrous iron (6.9 mmol g(-1) EPS). Amazingly, this EPS did not show any affinity for either ferric ions or selenium salts. This finding is one of the first steps in assessing the biotechnological potential of this polysaccharide.

A novel mcl-PHA produced on coprah oil by Pseudomonas guezennei biovar. tikehau, isolated from a "kopara" mat of French Polynesia.

Pseudomonas guezennei biovar. tikehau was isolated from a microbial mat on the atoll of Tikehau in French Polynesia, and is able to synthesize medium chain length poly-beta-hydroxyalkanaote copolymers when grown on coprah oil. A two-step cultivation process was used and the biosynthesis of PHAs was followed along 52h by regular culture sampling. The polyester was purified from freeze-dried cells and analysed by nuclear magnetic resonance (NMR), Fourier transform infra red (FTIR), and gas chromatography mass spectrometries. The copolyester produced by P. guezennei biovar. tikehau from coprah oil mainly consisted of saturated monomers, i.e. 3-hydroxyoctanoate (3HO) and 3-hydroxydecanoate (3HD), and the monomeric composition of the polyester did not change during the fermentation process. However, yield of PHAs production varied from 4% of the cellular dry weight (CDW) to 63% obtained after 36h. Scan electron microscopy was used to study the morphology and organization of PHAs granules within the cells and revealed the presence of several granules occupying almost the entire cell volume.

A novel exopolymer-producing bacterium, Paracoccus zeaxanthinifaciens subsp. payriae, isolated from a "kopara" mat located in Rangiroa, an atoll of French Polynesia.

An aerobic, mesophilic and heterotrophic marine bacterium designated RA19, able to produce two different exocellular polymers and zeaxanthin, was isolated from a French polynesian bacterial mat (localy named "kopara") situated in the atoll of Rangiroa. This microorganism, on the basis of its phenotypical features and the genotypic investigations, can be clearly assigned to the Parococcus zeaxanthinifaciens species and the name Parococcus zeaxanthinifaciens subsp. payriae is proposed. Optimal growth occurs between 30 degrees C and 35 degrees C, at pH between 6.5 and 7.5 and at ionic strength between 20 and 40 g/L of NaCl. The guanine-plus-cytosine content of DNA was 65.6%. This bacterium excreted, under laboratory conditions, two different polymers: a water-soluble exopolysaccharide (EPSI) consisting of 5 different sugars and a non-water-soluble macromolecule assumed to be of a glycoproteinic nature. The high sulfate content of the EPS1 and preliminary biological tests clearly showed that applications could be found in the very near future for both polymers in the cosmetic area. Their contribution to the viscous laminated microbial mat locally called "kopara" can be also mentioned.