Influence of Initial Film Properties in UVO-Mediated Patterning of an Elastomeric Film Using a TEM Grid.

Ultraviolet irradiation of a cross-linked polydimethylsiloxane (PDMS) Sylgard 184 film in the presence of atmospheric oxygen (UVO) through a bare transmission electron microscope (TEM) sample holding grid is a rather simple and widely utilized technique for creating micropatterned surfaces. The surface oxidation of a Sylgard 184 film due to UVO exposure is associated with densification and the formation of a silica-like surface layer, which under a TEM grid happens only over the exposed areas of the film, resulting in a physicochemical pattern. It is known that the depth (hD) of the features depends on the duration of UVO exposure (tE). In this article, we show for the first time that hD also depends on the initial film thickness (hF) and the cross-linker percentage (CL, ratio of part A to part B) in a Sylgard 184 thin film. We show that for a specific tE, hD progressively decreases with the reduction in hF. On the other hand, hD shows a nonmonotonic dependence with CL, resulting in patterns with maximum depth for CL ≈ 10.0%. We attribute this observation to the combined effect of resistance against the penetration of the propagation front by the rigid substrate as well as stress relaxation within the exposed parts of the film below the propagating front in films with higher CL values leading to the variation of hD. The observation reported here would allow the potential fabrication of polymer films with physicochemical patterns with feature height on demand by a one-step, facile technique.

Superior white electroluminescent devices using nitrogen-doped carbon dots/TiO2nanorods heterostructures.

Nitrogen-doped carbon dots (NCDs), exhibiting strong yellow emission in aqueous solution and solid matrices, have been utilized for fabricating heterostructure white electroluminescence devices. These devices consist of nitrogen-doped carbon dots as an emissive layer sandwiched between an organic hole transport layer (PEDOT:PSS) and an array of rutile TiO2nanorods, acting as an electron transport layer. Under an applied forward bias of 5 V, the device exhibits broadband electroluminescence covering the wavelength range of 390-900 nm, resulting in pure white light emission characteristics at room temperature. The result demonstrates the successful fabrication of all solution-processed, low-cost, eco-friendly NCDs-based LEDs with CIE (Commission Internationale d'Éclairage) coordinate of (0.31, 0.34) and color rendering index (CRI) > 90, which are close to ideal white light emission characteristics. The device functionalities are achieved based on defect-related NIR emission from TiO2nanorods array and visible emission from nitrogen-doped carbon dots. This result paves a new opportunity to develop low-cost, solution-processed nitrogen-doped carbon dots based on warm White light emitting diodes with high CRI for large-area display and lighting applications.

Damped Oscillatory Dynamics of a Drop Impacting over Oil-Infused Slippery Interfaces─Does the Oil Viscosity Slow it Down?

A liquid drop impacting on a soft surface is known to exhibit fascinating dynamics that is distinctive from its bounce-back atop a rigid surface. However, while the early spreading of the drop subsequent to its immediate impact with a lubricating liquid layer appears to be reasonably well understood, the later events of retraction and eventual stabilization appear to be poorly addressed. Here, we bring out the nontrivial confluence of the solid substrate wettability and the liquid layer viscosity toward modulating the post-collision dynamics of an impinging liquid drop on a viscous oil-infused surface during its later phase of settlement before arriving at an equilibrium state. Our results reveal that despite an intuitive analogy with the classical phenomenon of damped oscillation, the drop, during its later stages of motion, undergoes dynamical events that may be nontrivially dictated by not only the relative viscosity of the impacting drop and the liquid layer but also the intrinsic wettability of the solid substrate, governing its post-impact settlement via a sequel of spreading-retraction cycles. As a consequence, the viscous liquid layer, instead of providing additional damping, may nonintuitively reduce the effective viscous dissipation so as to hasten the drop's final settlement. These results may turn out to be critical in designing engineered surfaces for tuning the movement of drops in a preferential pathway, bearing decisive implications in the functionalities of liquid lenses, inkjet printing, spray coating and cooling, and several other emerging applications in the realm of lubricated fluidic interfaces.

Modulation of Biophysical Cues in Nature Inspired Patterning of Porous Silk Fibroin Scaffold for Replenishable Controlled Drug Delivery.

While a sticking plasteris enough for healing of most of the minor cuts they may get routinely, critical situations like surgical, gunshot, accidental or diabetic wounds;lacarations and other cutaneous deep cuts may require implants and simultaneous medications for healing. From the biophysical standpoint, an internal force-based physical surface stimulusis crucial for cellular sensing during wound repair. In this paper, the authors report the fabrication of a porous, biomimmetically patterned silk fibroin scaffold loaded with ampicillin, which exhibits controlled release of the drug along with possible replenishment of the same. In vitro swelling study reveals that the scaffolds with hierarchical surface patterns exhibit lower swelling and degradation than other types of scaffolds. The scaffolds, that show remarkable broad-spectrum antibacterial efficacy, exhibit Korsemeyer-Peppas model for the ampicillin release patterns due to the structural hydrophobicity imparted by the patterns. Four distinct cell-matrix adhesion regimes are investigated for the fibroblasts to eventually form cell sheets all over the hierarchical surface structures. 4',6-diamidino-2-phenylindole (DAPI) and Fluorescein Diacetate (FDA) fluorescent staining clearly demonstrate the superiority of patterned surface over its other variants. A comparative immunofluorescence study among collagen I, vinculin, and vimentin expressions substantiated the patterned surface to be superior to others.

Ordered non-close packed colloidal array with morphology control.

Non-close packed (NCP) colloidal arrays find wide applications in the fields of photonics, optical chip fabrication, nano sphere lithography and so on. However, unlike their close packed counterparts, such arrays cannot be obtained by direct self-organization of colloidal particles and require specialized techniques involving plasma/reactive ion etching, electric field driven assembly, substrate stretching or precise positioning of the particles. In this article, we present a facile template guided approach for fabricating ordered NCP arrays of colloidal particles. First, we employ soft lithography to replicate self-assembled hexagonal close packed (HCP) arrays of 'larger colloidal particles' (LPs) to obtain a topographically patterned positive and/or negative replica of the initial array. These replicas are then used as templates to spin coat 'smaller colloidal particles' (SPs), which may even have some degree of poly-dispersity, to obtain ordered NCP arrays. We further show that pattern morphology can be modulated based on whether a single or a double replicated template is used to confine the SPs, the concentration (Cn) of the SPs in the casting solution as well as the relative commensuration of the diameter of the SPs (ds) with that of the LPs (dL). Finally, we show that such NCP arrays can be transferred onto any flat surface by UVO mediated colloidal transfer printing.

Pattern Formation in Evaporative Drying of a Polymer Solution Droplet over a Soft Swellable Substrate.

We report morphological evolution and pattern formation during evaporative drying of a droplet of polymethylmethacrylate (PMMA) dissolved in tetrahydrofuran over a soft, swellable cross-linked Sylgard 184 substrate. In contrast to the well-known coffee ring formation due to the evaporation of a polymer solution droplet over a rigid substrate, we show that the situation becomes far more complicated over a Sylgard 184 substrate due to solvent penetration and associated swelling. The combined effect of evaporation and diffusive penetration leads to significantly faster solvent loss and results in the formation of an in situ thin polymer shell over the free surface of the evaporating droplet due to the attainment of local glass-transition concentration. The diffusive penetration of the solvent also leads to the spreading of the three-phase contact line (TPCL) of the droplet after dispensing. The vertical component of surface tension acting at the TPCL results in the formation of peripheral creases along the boundary of the droplet after the TPCL pins. With the progressive solvent loss, the shell eventually collapses, resulting in a buckled morphology with a central depression. We show that the evolution pathway and the final deposit morphology depend strongly on the initial PMMA concentration (Ci) in the droplet as it undergoes a transformation from a central depression surrounded by peripheral folds at lower Ci to a central depression along with radial wrinkles at higher Ci. During the late stage of the evolution process, the substrate undergoes de-swelling, which leads to flattening/rearrangement of the radial wrinkles, the extent of which again depends on Ci. We explored how the deposition pathway and patterns vary over a topographically patterned substrate and found out that the presence of topographic patterns leads to even faster solvent consumption due to enhanced diffusive penetration at the corrugated liquid─substrate interface, eventually resulting in deposition with a smaller footprint and partially aligned radial wrinkles. The results significantly enhance our understanding of droplet evaporation over a substrate into which the solvent can penetrate and unravel the complex physics, which is significantly dominated by swelling rather than evaporation only, which is common over a rigid, non-interacting substrate.

Droplet Impact Dynamics on Biomimetic Replica of Yellow Rose Petals: Rebound to Micropinning Transition.

Rose petals exhibit a phenomenal wetting property of being sticky and superhydrophobic simultaneously. A recent study has shown that for short timescales, associated with drop impact phenomenon, lotus leaf and rose petal replicas exhibit similar wettability, thereby highlighting the difference between long and short time wettability. Also, short time wetting on rose petals of different colors remains completely unaddressed, as almost all existing study on wetting of rose petals have been performed with the classical red rose (Rosa chinensis). In this paper, we compare the drop impact studies on replicas of a yellow rose petal, with those on extensively studied red rose petal replicas and the lotus leaf over a wide range of Weber number (We), by varying the height of fall (h) from 10 to 375 mm. Our results reveal that over the replica of a yellow rose petal, the initial impact outcome varies from complete rebound to micro pinning and eventually complete pinning depending on the kinetic energy of the impacting drop, in contrast to that on red rose petal replica on which the droplet always pinned. Based on experimental finding, we present a comprehensive regime phase map of the post impact behavior of the drop on different surfaces as a function of impact height. We also present a simple scaling analysis to understand the combined effect of pattern height and periodicity on the critical h corresponding to wetting regime transition. Additionally, variation of maximum spreading diameter and spreading time with the h for the different surfaces is also discussed. The results highlight that the initial impact dynamics of a water drop over a topographically patterned substrate is a strong function of the topographical parameters and can be very different from the equilibrium wetting state.

Non-wetting Liquid-Infused Slippery Paper.

Liquid-infused slippery surfaces have replaced structural superhydrophobic surfaces in a plethora of emerging applications, hallmarked by their favorable self-healing and liquid-repelling characteristics. Their ease of fabrication on different types of materials and increasing demand in various industrial applications have triggered research interests targeted toward developing an environmental-friendly, flexible, and frugal substrate as the underlying structural and functional backbone. Although many expensive polymers such as polytetrafluoroethylene have so far been used for their fabrication, these are constrained by their compromised flexibility and non-ecofriendliness due to the use of fluorine. Here, we explore the development and deployment of a biodegradable, recyclable, flexible, and an economically viable material in the form of a paper matrix for fabricating liquid-infused slippery interfaces for prolonged usage. We show by controlled experiments that a simple silanization followed by an oil infusion protocol imparts an inherent slipperiness (low contact angle hysteresis and low tilting angle for sliding) to the droplet motion on the paper substrate and provides favorable anti-icing characteristics, albeit keeping the paper microstructures unaltered. This ensures concomitant hydrophobicity, water adhesion, and capillarity for low surface tension fluids, such as mustard oil, with an implicit role played by the paper pore size distribution toward retaining a stable layer of the infused oil. With demonstrated supreme anti-icing characteristics, these results open up new possibilities of realizing high-throughput paper-based substrates for a wide variety of applications ranging from biomedical unit operations to droplet-based digital microfluidics.

Evaluation of grain boundaries as percolation pathways in quartz-rich continental crust using Atomic Force Microscopy.

Hydrous fluids play a vital role in the chemical and rheological evolution of ductile, quartz-bearing continental crust, where fluid percolation pathways are controlled by grain boundary domains. In this study, widths of grain boundary domains in seven quartzite samples metamorphosed under varying crustal conditions were investigated using Atomic Force Microscopy (AFM) which allows comparatively easy, high magnification imaging and precise width measurements. It is observed that dynamic recrystallization at higher metamorphic grades is much more efficient at reducing grain boundary widths than at lower temperature conditions. The concept of force-distance spectroscopy, applied to geological samples for the first time, allows qualitative estimation of variations in the strength of grain boundary domains. The strength of grain boundary domains is inferred to be higher in the high grade quartzites, which is supported by Kernel Average Misorientation (KAM) studies using Electron Backscatter Diffraction (EBSD). The results of the study show that quartzites deformed and metamorphosed at higher grades have narrower channels without pores and an abundance of periodically arranged bridges oriented at right angles to the length of the boundary. We conclude that grain boundary domains in quartz-rich rocks are more resistant to fluid percolation in the granulite rather than the greenschist facies.

Substrate wettability guided oriented self assembly of Janus particles.

Self-assembly of Janus particles with spatial inhomogeneous properties is of fundamental importance in diverse areas of sciences and has been extensively observed as a favorably functionalized fluidic interface or in a dilute solution. Interestingly, the unique and non-trivial role of surface wettability on oriented self-assembly of Janus particles has remained largely unexplored. Here, the exclusive role of substrate wettability in directing the orientation of amphiphilic metal-polymer Bifacial spherical Janus particles, obtained by topo-selective metal deposition on colloidal Polymestyere (PS) particles, is explored by drop casting a dilute dispersion of the Janus colloids. While all particles orient with their polymeric (hydrophobic) and metallic (hydrophilic) sides facing upwards on hydrophilic and hydrophobic substrates respectively, they exhibit random orientation on a neutral substrate. The substrate wettability guided orientation of the Janus particles is captured using molecular dynamic simulation, which highlights that the arrangement of water molecules and their local densities near the substrate guide the specific orientation. Finally, it is shown that by spin coating it becomes possible to create a hexagonal close-packed array of the Janus colloids with specific orientation on differential wettability substrates. The results reported here open up new possibilities of substrate-wettability driven functional coatings of Janus particles, which has hitherto remained unexplored.

Evaporation-induced alterations in oscillation and flow characteristics of a sessile droplet on a rose-mimetic surface.

Strategic control of evaporation dynamics can help control oscillation modes and internal flow field in an oscillating sessile droplet. This article presents the study of an oscillating droplet on a bio-inspired "sticky" surface to better understand the nexus between the modes of evaporation and oscillation. Oscillation in droplets can be characterized by the number of nodes forming on the surface and is referred to as the mode of oscillation. An evaporating sessile droplet under constant periodic perturbation naturally self-tunes between different oscillation modes depending on its geometry. The droplet geometry evolves according to the mode of evaporation controlled by substrate topography. We use a bio-inspired, rose patterned, "sticky" hydrophobic substrate to perpetually pin the contact line of the droplet in order to hence achieve a single mode of evaporation for most of the droplet's lifetime. This allows the prediction of experimentally observed oscillation mode transitions at different excitation frequencies. We present simple scaling arguments to predict the velocity of the internal flow induced by the oscillation. The findings are beneficial to applications which seek to tailor energy and mass transfer rates across liquid droplets by using bio-inspired surfaces.

Improved Mesenchymal Stem Cell Proliferation, Differentiation, Epithelial Transition, and Restrained Senescence on Hierarchically Patterned Porous Honey Silk Fibroin Scaffolds.

We report a significant improvement of adipose-derived mesenchymal stem cells' (ADMSCs) biocompatibility and proliferation on hierarchically patterned porous honey-incorporated silk fibroin scaffolds fabricated using a combination of soft lithography and freeze-drying techniques. Parametric variations show enhanced surface roughness, swelling, and degradation rate with good pore interconnectivity, porosity, and mechanical strength for soft-lithographically fabricated biomimetic microdome arrays on the 2% honey silk fibroin scaffold (PHSF2) as compared to its other variants, which eventually made PHSF2 more comparable to the native environment required for stem cell adhesion and proliferation. PHSF2 also exhibits sustained honey release with remarkable antibacterial efficacy against methicillin-resistant Staphylococcus aureus (MRSA). Honey incorporation (biochemical cue) influences microdome structural features, that is, biophysical cues (height, width, and periodicity), which further allows ADMSCs pseudopods (filopodia) to grasp the microdomes for efficient cell-cell communication and cell-matrix interaction and regulates ADMSCs behavior by altering their cytoskeletal rearrangement and thereby increases the cellular spreading area and cell sheet formation. The synergistic effect of biochemical (honey) and biophysical (patterns) cues on ADMSCs studied by the nitro blue tetrazolium assay and DCFDA fluorescence spectroscopy reveals limited free radical generation within cells. Molecular expression studies show a decrease in p53 and p21 expressions validating ADMSCs senescence inhibition, which is further correlated with a decrease in cellular senescence-associated ß galactosidase activity. We also show that an increase in CDH1 and CK19 molecular expressions along with an increase in SOX9, RUNX2, and PPARγ molecular expressions supported by PHSF2 justify the substrate's efficacy of underpinning mesenchymal to epithelial transition and multilineage trans-differentiation. This work highlights the fabrication of a naturally healing nutraceutical (honey)-embedded patterned porous stand-alone tool with the potential to be used as smart stem cells delivering regenerative healing implant.

Nanoparticle Induced Morphology Modulation in Spin Coated PS/PMMA Blend Thin Films.

The influence of adding nanoparticles on the ascast morphology of spin coated immiscible polystyrene/poly(methyl methacrylate) (PS/PMMA) thin films of different thickness (hE) and composition (RB, volume ratio of PS to PMMA) has been explored in this article. To understand the precise effect of nanoparticle addition, the morphology of PS/PMMA thin blend films spin cast from toluene on a native oxide covered silicon wafer substrate was first investigated. It is seen that in particle free films, the generic morphology of the films remains nearly unaltered with increase in hE, for RB = 3:1 and 1:3. In contrast, strong hE dependent morphology transformation is observed in films with RB = 1:1. Subsequently, thiol-capped gold nanoparticles (AuNP) containing films with different particle concentrations (CNP) were cast from the same solvent along with the polymer mixture. We observe that addition of AuNPs barely alters the generic morphology of the films with RB = 3:1. In contrast, the presence of the particles significantly influences the morphology of the films with RB = 1:1 and 1:3, particularly at higher CNP (≈10.0%). X-ray photoelectron spectroscopy and X-ray reflectivity of some samples reveal that the AuNPs tend to migrate to the free surface through the PS phase, thereby stabilizing this layer partially or fully (depending on CNP) against dewetting over a surface of adsorbed PMMA layer and influencing the ascast morphology as a function of CNP. The work is fundamentally important in understanding largely overlooked implications of nanoparticle addition on the morphology of PS/PMMA blend thin films which forms the fundamental basis for future interesting studies involving dynamics of nanoparticles within the blend thin films.

Dual cross-linked honey coupled 3D antimicrobial alginate hydrogels for cutaneous wound healing.

We report potentiation of healing efficacy of alginate by value addition at its structural level. Dual crosslinked (ionically and covalently) sodium alginate hydrogel coupled with honey (HSAG) brings about an intermediate stiffness in the fabric, confers consistent swelling property and limits erratic degradation of the polymer which ultimately provides conducive milieu to cellular growth and proliferation. In this work honey concentrations in HSAGs are varied from 2% to 10%. FTIR, XRD and nanoindentation studies on the HSAGs exhibited physicochemical integrity. In vitro degradation study provided the crucial finding on 4% HSAG having controlled degradation rate up to 12 days with a weight loss of 87.36 ± 1.14%. This particular substrate also has an ordered crystalline surface morphology with decent cellular viability (HaCaT and 3T3) and antimicrobial potential against Methicillin Resistant Staphylococcus aureus (MRSA) and Escherichia coli. The in vivo wound contraction kinetics on murine models (4% HSAG treated wound contraction: 94.56 ± 0.1%) has been monitored by both invasive (histopathology) and noninvasive (Swept Source Optical Coherence Tomography) imaging and upon corroborating them it evidenced that 4% HSAG treated wound closure achieved epithelial thickness resembling to that of unwounded skin. Thus, the work highlights structurally modified alginate hydrogel embedded with honey as a potential antimicrobial healing agent.

Flow and deformation characteristics of a flexible microfluidic channel with axial gradients in wall elasticity.

Axial gradients in wall elasticity may have significant implications in the deformation and flow characteristics of a narrow fluidic conduit, bearing far-reaching consequences in physiology and bio-engineering. Here, we present a theoretical and experimental framework for fluid-structure interactions in microfluidic channels with axial gradients in wall elasticity, in an effort to arrive at a potential conceptual foundation for in vitro study of mirovascular physiology. Towards this, we bring out the static deformation and steady flow characteristics of a circular microchannel made of polydimethylsiloxane (PDMS) bulk, considering imposed gradients in the substrate elasticity. In particular, we study two kinds of elasticity variations - a uniformly soft (or hard) channel with a central strip that is hard (or soft), and, increasing elasticity along the length of the channel. The former kind yields a centrally constricted (or expanded) deformed profile in response to the flow. The latter kind leads to increasingly bulged channel radius from inlet to outlet in response to flow. We also formulate an analytical model capturing the essential physics of the underlying elastohydrodynamic interactions. The theoretical predictions match favourably with the experimental observations and are also in line with reported results on stenosis in mice. The present framework, thus, holds the potential for acting as a fundamental design basis towards developing in vitro models for micro-circulation, capable of capturing exclusive artefacts of healthy and diseased conditions.

High Temperature Durability of Oleoplaned Slippery Copper Surfaces.

Slippery surfaces, inspired by the functionality of trapping interfaces of specialized leaves of pitcher plants, have been widely used in self-cleaning, anti-icing, antifrost, and self-healing surfaces. They can be fabricated on metallic surfaces as well, presenting a more durable and low-maintenance anticorrosive surface on metals. However, the lack of studies on the durability of these slippery surfaces at high temperature prohibits their practical deployment in real industrial applications where thermal effects are critical and high temperature conditions are inevitable. We present here a unique fabrication technique of a copper-based oleoplaned slippery surface that has been tested for high temperature durability under repeated thermal cycles. Their slipperiness at high temperatures has also been tested in the absence of the Leidenfrost effect. Our findings suggest that these new substrates can be used for fabricating low maintenance surfaces for high temperature applications or even where the surface undergoes repeated thermal cycles like heat exchanger pipes, utensils, engine casings, and outdoor metallic structures.

Influence of Substrate Surface Properties on Spin Dewetting, Texture, and Phase Transitions of 5CB Liquid-Crystal Thin Films.

We report how the texture and stability of a nematic liquid-crystal (LC) thin film of 5CB vary as a function of UV-ozone (UVO) exposure of the underlying poly(methyl methacrylate) (PMMA) substrate. UVO exposure of the PMMA substrate not only increases its surface energy, making it more wettable, but also results in the generation of oxygen-containing polar functional groups on the PMMA surface due to photolysis of ester. While the stability of the 5CB films is expectedly enhanced on UVO-exposed PMMA substrates against thermally induced dewetting, the texture of the film also changes as a function of the UV exposure time (tE). We show that the films continue to exhibit the nematic Schlieren texture for tE ≤ 20 min, although the disclination point density (|m|) gradually reduces with an increase in tE. However, the texture changes completely to a spherulite or fanlike texture in tE ≥ 20 min due to enhanced anchoring of the 5CB molecules on the substrates. In addition, enhanced wettability and stronger anchoring by the UVO-exposed PMMA substrates also suppress the tendency of spin dewetting of the 5CB films due to spontaneous rupture of the dispensed solution layer during spin coating, particularly when the solute concentration (Cn) is very low. The latter observation allows possible creation of thinner LC films, which are otherwise difficult to form by spin coating due to enhanced cohesive interactions between the anisotropic LC molecules. Finally, we show that in continuous films, the nematic-to-isotropic (N → I) and I → N phase transitions with gradual heating and cooling remain completely reversible, irrespective of the texture of the film and wettability of the substrate.

Evaporative Drying of Sodium Chloride Solution Droplet on a Thermally Controlled Substrate.

We report the evaporative drying-mediated pattern formation of dilute aqueous NaCl solution droplets on a hydrophobic surface made of cross-linked PDMS at elevated temperatures. Experiments were performed with various salt concentrations (0.08 to 2 M). Depending on the substrate temperature (TS) and initial salt concentration (Cn), a variety of unique deposition morphologies are obtained. Double salt rings are obtained at low Cn (0.08 and 0.1 M) at TS ≈ 75 °C. With the increase in Cn, the deposition morphology transforms into a single peripheral ring with a central deposition zone that is devoid of any salt deposition. On the other hand, at lower Cn and lower TS, a single outer ring deposit surrounding a central region covered with dendritic salt deposits is observed. The variation in the morphology as well as the number of rings formed is attributed to the relative strengths of the radially outward capillary-driven flow, inward Marangoni flow, and inward diffusive transport of the salt ions. A morphology phase diagram shows the collective dependence of the final deposition pattern as a function of both TS and Cn.

Tunable adhesion and slip on a bio-mimetic sticky soft surface.

Simultaneous tuning of wettability and adhesion of a surface requires intricate procedures for altering the interfacial structures. Here, we present a simple method for preparing a stable slippery surface, with an intrinsic capability of varying its adhesion characteristics. Cross-linked PDMS, an inherent hydrophobic material commonly used for microfluidic applications, is used to replicate the structures on the surface of a rose petal which acts as a high adhesion solid base and is subsequently oleoplaned with silicone oil. Our results demonstrate that the complex hierarchical rose petal structures can arrest dewetting of the silicone oil on the cross linked PDMS base by anchoring the oil film strongly even under flow. Further, by tuning the extent of submergence of the rose petal structures with silicone oil, we could alter the adhesion characteristics of the surface on demand, while retaining its slippery characteristics for a wide range of the pertinent parameters. We have also demonstrated the possible fabrication of gradient adhesion surfaces. This, in turn, may find a wide variety of applications in water harvesting, droplet maneuverability and no-loss transportation in resource-limited settings.

Dynamics of droplet impingement on bioinspired surface: insights into spreading, anomalous stickiness and break-up.

Inspired by the self-cleaning ability of lotus leaves and stickiness (towards water) of rose petals, we investigate the droplet impact dynamics on such bioinspired substrates. Impact studies are carried out with water droplets for a range of impact velocities on glass, PDMS and soft lithographically fabricated replicas of the lotus leaf and rose petals, which exhibit near identical wetting properties as that of the original biological entities. In this work, we investigate the spreading, dewetting and droplet break-up mechanisms subsequent to impact. Surprisingly, the rose petal and lotus leaf replicas manifest similar impact dynamics. The observation is extremely intriguing and counterintuitive, as rose petal and its replicas are sticky in contrast to lotus leaves. However, these observations are based on experiments performed with sessile water droplets. By contrast, in the current study, we find that rose petal replicas exhibit non-sticky behaviour at the short time scale ∼ ( O ( 10 - 3 ) ) s similar to that exhibited by lotus leaf replicas. Air entrapment in the micrometre features of bioinspired surfaces prevent frictional dissipation of droplet kinetic energy, leading to contact edge recession. We have also unveiled interesting universal physics that govern the spreading, recession of the contact edge and subsequent break-up modes (ligament or bulb-ligament) of the droplet.