Scalable Non-Halogenated Co-solvent System for Large-Area, Four-Layer Slot-Die-Coated Organic Photovoltaics.

Sustainable processing solvents, photoactive materials, and scalable manufacturing will play a key role in commercializing printed organic photovoltaics (OPVs). The record-breaking pioneering OPV reports have done an outstanding job in accelerating the discovery of champion photoactive materials and device engineering practices; however, these works predominantly involve health-hazardous halogenated processing solvents/additives and non-scalable thin-film coating methods. Herein, large-area slot-die-manufactured OPV cells from eco-friendly halogen-free solvents and synthetically scalable materials are showcased. All the four layers; electron transport layer (SnO2), cathode interlayer (PDIN-H), bulk-heterojunction (BHJ, PTQ-10:BTP-4F-12), and hole transport layer [poly(3,4-ethylenedioxythiophene):polystyrene sulfonate) (PEDOT:PSS] are slot-die-coated in air. A non-halogenated co-solvent mixture of toluene and 2-methyl tetrahydrofuran is presented as an optimal processing solvent to realize the high-quality thin films of PTQ10:BTP-4F-12. The unencapsulated champion solar cells characterized in ambient conditions (RH = 30%, T = 22 °C) exhibit power conversion efficiencies (PCEs) of 12.1 and 17.8% under 1 Sun (100 mW/cm2) and indoor light-emitting diode lighting (580 µW/cm2) conditions, respectively. Additionally, PEDOT:PSS is successfully slot-die-coated atop BHJ by mitigating wettability challenges with the aid of surface treatment. The all four-layer slot-die-coated OPVs exhibit a PCE of 9.55%.

Processing of Lead Halide Perovskite Thin Films Studied with In-Situ Real-Time X-ray Scattering.

Lead halide perovskites have been of paramount interest for solution-processable solar cells, reaching power conversion efficiencies larger than 25%. In this spotlight, we will provide a systematic overview of the influence of different solution-based processing routes of lead halide perovskites on their phase transformation and conversion as revealed through in-situ X-ray-scattering experiments. These experiments were performed in conditions closely mimicking thin film processing methods and conditions used for thin film solar cell device fabrication and therefore provide critical information about the mechanism of the phase transformation, its onset, the kinetics, as well as the emergence and disappearance of various (meso)phases along the way. The measurements capture the overall solidification and conversion process of lead halide perovskite inks into solid films via so-called one-step and two-step spin-coating processes as well as blade coating and hot casting. Processing routes are applied to films based on basic components as well as mixtures of different anions and cations, solvents, and antisolvents, all of which deeply affect the thin film microstructure and morphology of the light-absorbing semiconductor and associated solar cell devices.

Zinc Oxide-Perylene Diimide Hybrid Electron Transport Layers for Air-Processed Inverted Organic Photovoltaic Devices.

In this work, we report the formation of perylene diimide films, from green solvents, for use as electron transporting layers, when combined with ZnO, in inverted-type organic photovoltaics. A modified N-annulated PDI was functionalized with a tert-butyloxycarbonyl protecting group to solubilize the material, enabling solution processing from green solvents. Post-deposition treatment of films via thermal annealing cleaves the protecting group yielding the known PDIN-H material, rendering films solvent-resistant. The PDIN-H films were characterized by optical absorption spectroscopy, contact angle measurements, and atomic force microscopy. When used to modify the surface of ZnO in inverted-type organic photovoltaics (air-processed and tested) based on the PM6:Y6 and PTQ10:Y6 bulk-heterojunctions, the device power conversion efficiency increases from 9.8 to 11.0% and 7.2 to 9.8%, respectively.

Implication of polymeric template agent on the formation process of hybrid halide perovskite films.

The use of polymeric additives supporting the growth of hybrid halide perovskites has proven to be a successful approach aiming at high quality active layers targeting optoelectronic exploitation. A detailed description of the complex process involving the self-assembly of the precursors into the perovskite crystallites in presence of the polymer is, however, still missing. Here we take starch:CH3NH3PbI3 (MAPbI3) as example of highly performing composite, both in solar cells and light emitting diodes, and study the film formation process through differential scanning calorimetry and in situ time-resolved grazing incidence wide-angle x-ray scattering, performed during spin coating. These measurements reveal that starch beneficially influences the nucleation and growth of the perovskite precursor phase, leading to improved structural properties of the resulting film which turns into higher stability towards environmental conditions.

Compositional and Interfacial Engineering Yield High-Performance and Stable p-i-n Perovskite Solar Cells and Mini-Modules.

Through the optimization of the perovskite precursor composition and interfaces to selective contacts, we achieved a p-i-n-type perovskite solar cell (PSC) with a 22.3% power conversion efficiency (PCE). This is a new performance record for a PSC with an absorber bandgap of 1.63 eV. We demonstrate that the high device performance originates from a synergy between (1) an improved perovskite absorber quality when introducing formamidinium chloride (FACl) as an additive in the "triple cation" Cs0.05FA0.79MA0.16PbBr0.51I2.49 (Cs-MAFA) perovskite precursor ink, (2) an increased open-circuit voltage, VOC, due to reduced recombination losses when using a lithium fluoride (LiF) interfacial buffer layer, and (3) high-quality hole-selective contacts with a self-assembled monolayer (SAM) of [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz) on ITO electrodes. While all devices exhibit a high performance after fabrication, as determined from current-density voltage, J-V, measurements, substantial differences in device performance become apparent when considering longer-term stability data. A reduced long-term stability of devices with the introduction of a LiF interlayer is compensated for by using FACl as an additive in the metal-halide perovskite thin-film deposition. Optimized devices maintained about 80% of the initial average PCE during maximum power point (MPP) tracking for >700 h. We scaled the optimized device architecture to larger areas and achieved fully laser patterned series-interconnected mini-modules with a PCE of 19.4% for a 2.2 cm2 active area. A robust device architecture and reproducible deposition methods are fundamental for high performance and stable large-area single junction and tandem modules based on PSCs.

Facile and noninvasive passivation, doping and chemical tuning of macroscopic hybrid perovskite crystals.

Halide vacancies and associated metallic lead (Pb°) observed at the surface and deep inside macroscopic organolead trihalide perovskite crystals is removed through a facile and noninvasive treatment. Indeed, Br2 vapor is shown to passivate Br-vacancies and associated Pb° in the bulk of macroscopic crystals. Controlling the exposure time can markedly improve the overall stoichiometry for moderate exposures or introduce excessive bromide for long exposures, resulting in p-doping of the crystals. In the low dose passivation regime, Hall effect measurements reveal a ca. 3-fold increase in carrier mobility to ca. 15 cm2V-1s-1, while the p-doping increases the electrical conductivity ca. 10000-fold, including a 50-fold increase in carrier mobility to ca. 150 cm2V-1s-1. The ease of diffusion of Br2 vapor into macroscopic crystals is ascribed to the porosity allowed in rapidly grown crystals through aggregative processes of the colloidal sol during growth of films and macroscopic crystals. This process is believed to form significant growth defects, including open voids, which may be remnants of the escaping solvent at the solidification front. These results suggest that due to the sol-gel-like nature of the growth process, macroscopic perovskite crystals reported in this study are far from perfect and point to possible pathways to improving the optoelectronic properties of these materials. Nevertheless, the ability of the vapor-phase approach to access and tune the bulk chemistry and properties of nominally macroscopic perovskite crystals provides interesting new opportunities to precisely manipulate and functionalize the bulk properties of hybrid perovskite crystals in a noninvasive manner.

Kinetic Stabilization of the Sol-Gel State in Perovskites Enables Facile Processing of High-Efficiency Solar Cells.

Perovskite solar cells increasingly feature mixed-halide mixed-cation compounds (FA1- x - y MAx Csy PbI3- z Brz ) as photovoltaic absorbers, as they enable easier processing and improved stability. Here, the underlying reasons for ease of processing are revealed. It is found that halide and cation engineering leads to a systematic widening of the anti-solvent processing window for the fabrication of high-quality films and efficient solar cells. This window widens from seconds, in the case of single cation/halide systems (e.g., MAPbI3 , FAPbI3 , and FAPbBr3 ), to several minutes for mixed systems. In situ X-ray diffraction studies reveal that the processing window is closely related to the crystallization of the disordered sol-gel and to the number of crystalline byproducts; the processing window therefore depends directly on the precise cation/halide composition. Moreover, anti-solvent dripping is shown to promote the desired perovskite phase with careful formulation. The processing window of perovskite solar cells, as defined by the latest time the anti-solvent drip yields efficient solar cells, broadened with the increasing complexity of cation/halide content. This behavior is ascribed to kinetic stabilization of sol-gel state through cation/halide engineering. This provides guidelines for designing new formulations, aimed at formation of the perovskite phase, ultimately resulting in high-efficiency perovskite solar cells produced with ease and with high reproducibility.

Lattice anchoring stabilizes solution-processed semiconductors.

The stability of solution-processed semiconductors remains an important area for improvement on their path to wider deployment. Inorganic caesium lead halide perovskites have a bandgap well suited to tandem solar cells1 but suffer from an undesired phase transition near room temperature2. Colloidal quantum dots (CQDs) are structurally robust materials prized for their size-tunable bandgap3; however, they also require further advances in stability because they are prone to aggregation and surface oxidization at high temperatures as a consequence of incomplete surface passivation4,5. Here we report 'lattice-anchored' hybrid materials that combine caesium lead halide perovskites with lead chalcogenide CQDs, in which lattice matching between the two materials contributes to a stability exceeding that of the constituents. We find that CQDs keep the perovskite in its desired cubic phase, suppressing the transition to the undesired lattice-mismatched phases. The stability of the CQD-anchored perovskite in air is enhanced by an order of magnitude compared with pristine perovskite, and the material remains stable for more than six months at ambient conditions (25 degrees Celsius and about 30 per cent humidity) and more than five hours at 200 degrees Celsius. The perovskite prevents oxidation of the CQD surfaces and reduces the agglomeration of the nanoparticles at 100 degrees Celsius by a factor of five compared with CQD controls. The matrix-protected CQDs show a photoluminescence quantum efficiency of 30 per cent for a CQD solid emitting at infrared wavelengths. The lattice-anchored CQD:perovskite solid exhibits a doubling in charge carrier mobility as a result of a reduced energy barrier for carrier hopping compared with the pure CQD solid. These benefits have potential uses in solution-processed optoelectronic devices.

Conducting and Stretchable PEDOT:PSS Electrodes: Role of Additives on Self-Assembly, Morphology, and Transport.

The addition of dimethylsulfoxide and Zonyl into poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) can be combined to achieve excellent electrical, optical, and mechanical properties. We demonstrate that it is possible to produce highly transparent conducting electrodes (FoM > 35) with low Young's modulus and high carrier density. We investigated the relationship between the transport properties of PEDOT:PSS and the morphology and microstructure of these films by performing Hall effect measurement, atomic force microscopy, and grazing incidence wide-angle X-ray scattering (GIWAXS). Our analysis reveals the distinctive impact of the two additives on the PEDOT and PSS components in the solid-state PEDOT:PSS films. Both additives induce fibrillar formation in the film, and the combination of the two additives only enhances the fibrillary nature and the aggregations of both PEDOT and PSS components of the film. In situ GIWAXS allows to time-resolve the morphology evolution. Our analysis reveals the influence of additives on the aggregation and self-assembly behaviors of the PEDOT and PSS components. Aggregation occurs during the transition from wet to dry film, which is observed exclusively during the thermal annealing step of the as-cast hydrated film. These results indicate that the additives directly influence the self-assembly behaviors of PEDOT and PSS during the ink-to-solid phase transformation of the hydrated film, which occurs primarily during the initial seconds of post-deposition thermal annealing.

Multi-inch single-crystalline perovskite membrane for high-detectivity flexible photosensors.

Single crystalline perovskites exhibit high optical absorption, long carrier lifetime, large carrier mobility, low trap-state-density and high defect tolerance. Unfortunately, all single crystalline perovskites attained so far are limited to bulk single crystals and small area wafers. As such, it is impossible to design highly demanded flexible single-crystalline electronics and wearable devices including displays, touch sensing devices, transistors, etc. Herein we report a method of induced peripheral crystallization to prepare large area flexible single-crystalline membrane (SCM) of phenylethylamine lead iodide (C6H5C2H4NH3)2PbI4 with area exceeding 2500 mm2 and thinness as little as 0.6 µm. The ultrathin flexible SCM exhibits ultralow defect density, superior uniformity and long-term stability. Using the superior ultrathin membrane, a series of flexible photosensors were designed and fabricated to exhibit very high external quantum efficiency of 26530%, responsivity of 98.17 A W-1 and detectivity as much as 1.62 × 1015 cm Hz1/2 W-1 (Jones).

Compositional and orientational control in metal halide perovskites of reduced dimensionality.

Reduced-dimensional metal halide perovskites (RDPs) have attracted significant attention in recent years due to their promising light harvesting and emissive properties. We sought to increase the systematic understanding of how RDPs are formed. Here we report that layered intermediate complexes formed with the solvent provide a scaffold that facilitates the nucleation and growth of RDPs during annealing, as observed via in situ X-ray scattering. Transient absorption spectroscopy of RDP single crystals and films enables the identification of the distribution of quantum well thicknesses. These insights allow us to develop a kinetic model of RDP formation that accounts for the experimentally observed size distribution of wells. RDPs exhibit a thickness distribution (with sizes that extend above n = 5) determined largely by the stoichiometric proportion between the intercalating cation and solvent complexes. The results indicate a means to control the distribution, composition and orientation of RDPs via the selection of the intercalating cation, the solvent and the deposition technique.

2D matrix engineering for homogeneous quantum dot coupling in photovoltaic solids.

Colloidal quantum dots (CQDs) are promising photovoltaic (PV) materials because of their widely tunable absorption spectrum controlled by nanocrystal size1,2. Their bandgap tunability allows not only the optimization of single-junction cells, but also the fabrication of multijunction cells that complement perovskites and silicon 3 . Advances in surface passivation2,4-7, combined with advances in device structures 8 , have contributed to certified power conversion efficiencies (PCEs) that rose to 11% in 2016 9 . Further gains in performance are available if the thickness of the devices can be increased to maximize the light harvesting at a high fill factor (FF). However, at present the active layer thickness is limited to ~300 nm by the concomitant photocarrier diffusion length. To date, CQD devices thicker than this typically exhibit decreases in short-circuit current (JSC) and open-circuit voltage (VOC), as seen in previous reports3,9-11. Here, we report a matrix engineering strategy for CQD solids that significantly enhances the photocarrier diffusion length. We find that a hybrid inorganic-amine coordinating complex enables us to generate a high-quality two-dimensionally (2D) confined inorganic matrix that programmes internanoparticle spacing at the atomic scale. This strategy enables the reduction of structural and energetic disorder in the solid and concurrent improvements in the CQD packing density and uniformity. Consequently, planar devices with a nearly doubled active layer thicknesses (~600 nm) and record values of JSC (32 mA cm-2) are fabricated. The VOC improved as the current was increased. We demonstrate CQD solar cells with a certified record efficiency of 12%.

Phase Transition Control for High Performance Ruddlesden-Popper Perovskite Solar Cells.

Ruddlesden-Popper reduced-dimensional hybrid perovskite (RDP) semiconductors have attracted significant attention recently due to their promising stability and excellent optoelectronic properties. Here, the RDP crystallization mechanism in real time from liquid precursors to the solid film is investigated, and how the phase transition kinetics influences phase purity, quantum well orientation, and photovoltaic performance is revealed. An important template-induced nucleation and growth of the desired (BA)2 (MA)3 Pb4 I13 phase, which is achieved only via direct crystallization without formation of intermediate phases, is observed. As such, the thermodynamically preferred perpendicular crystal orientation and high phase purity are obtained. At low temperature, the formation of intermediate phases, including PbI2 crystals and solvate complexes, slows down intercalation of ions and increases nucleation barrier, leading to formation of multiple RDP phases and orientation randomness. These insights enable to obtain high quality (BA)2 (MA)3 Pb4 I13 films with preferentially perpendicular quantum well orientation, high phase purity, smooth film surface, and improved optoelectronic properties. The resulting devices exhibit high power conversion efficiency of 12.17%. This work should help guide the perovskite community to better control Ruddlesden-Popper perovskite structure and further improve optoelectronic and solar cell devices.

Stable High-Performance Perovskite Solar Cells via Grain Boundary Passivation.

The trap states at grain boundaries (GBs) within polycrystalline perovskite films deteriorate their optoelectronic properties, making GB engineering particularly important for stable high-performance optoelectronic devices. It is demonstrated that trap states within bulk films can be effectively passivated by semiconducting molecules with Lewis acid or base functional groups. The perovskite crystallization kinetics are studied using in situ synchrotron-based grazing-incidence X-ray scattering to explore the film formation mechanism. A model of the passivation mechanism is proposed to understand how the molecules simultaneously passivate the Pb-I antisite defects and vacancies created by under-coordinated Pb atoms. In addition, it also explains how the energy offset between the semiconducting molecules and the perovskite influences trap states and intergrain carrier transport. The superior optoelectronic properties are attained by optimizing the molecular passivation treatments. These benefits are translated into significant enhancements of the power conversion efficiencies to 19.3%, as well as improved environmental and thermal stability of solar cells. The passivated devices without encapsulation degrade only by ≈13% after 40 d of exposure in 50% relative humidity at room temperature, and only ≈10% after 24 h at 80 °C in controlled environment.

Enhanced Electrical Conductivity of Molecularly p-Doped Poly(3-hexylthiophene) through Understanding the Correlation with Solid-State Order.

Molecular p-doping of the conjugated polymer poly(3-hexylthiophene) (P3HT) with 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) is a widely studied model system. Underlying structure-property relationships are poorly understood because processing and doping are often carried out simultaneously. Here, we exploit doping from the vapor phase, which allows us to disentangle the influence of processing and doping. Through this approach, we are able to establish how the electrical conductivity varies with regard to a series of predefined structural parameters. We demonstrate that improving the degree of solid-state order, which we control through the choice of processing solvent and regioregularity, strongly increases the electrical conductivity. As a result, we achieve a value of up to 12.7 S cm-1 for P3HT:F4TCNQ. We determine the F4TCNQ anion concentration and find that the number of (bound + mobile) charge carriers of about 10-4 mol cm-3 is not influenced by the degree of solid-state order. Thus, the observed increase in electrical conductivity by almost 2 orders of magnitude can be attributed to an increase in charge-carrier mobility to more than 10-1 cm2 V-1 s-1. Surprisingly, in contrast to charge transport in undoped P3HT, we find that the molecular weight of the polymer does not strongly influence the electrical conductivity, which highlights the need for studies that elucidate structure-property relationships of strongly doped conjugated polymers.

Effects of High Temperature and Thermal Cycling on the Performance of Perovskite Solar Cells: Acceleration of Charge Recombination and Deterioration of Charge Extraction.

In this work, we investigated the effects of high operating temperature and thermal cycling on the photovoltaic (PV) performance of perovskite solar cells (PSCs) with a typical mesostructured (m)-TiO2-CH3NH3PbI3-xClx-spiro-OMeTAD architecture. After temperature-dependent grazing-incidence wide-angle X-ray scattering, in situ X-ray diffraction, and optical absorption experiments were carried out, the thermal durability of PSCs was tested by subjecting the devices to repetitive heating to 70 °C and cooling to room temperature (20 °C). An unexpected regenerative effect was observed after the first thermal cycle; the average power conversion efficiency (PCE) increased by approximately 10% in reference to the as-prepared device. This increase of PCE was attributed to the heating-induced improvement of the crystallinity and p doping in the hole transporter, spiro-OMeTAD, which promotes the efficient extraction of photogenerated carriers. However, further thermal cycles produced a detrimental effect on the PV performance of PSCs, with the short-circuit current and fill factor degrading faster than the open-circuit voltage. Similarly, the PV performance of PSCs degraded at high operation temperatures; both the short-circuit current and open-circuit voltage decreased with increasing temperature, but the temperature-dependent trend of the fill factor was the opposite. Our impedance spectroscopy analysis revealed a monotonous increase of the charge-transfer resistance and a concurrent decrease of the charge-recombination resistance with increasing temperature, indicating a high recombination of charge carriers. Our results revealed that both thermal cycling and high temperatures produce irreversible detrimental effects on the PSC performance because of the deteriorated interfacial photocarrier extraction. The present findings suggest that the development of robust charge transporters and proper interface engineering are critical for the deployment of perovskite PVs in harsh thermal environments.

Programmable and coherent crystallization of semiconductors.

The functional properties and technological utility of polycrystalline materials are largely determined by the structure, geometry, and spatial distribution of their multitude of crystals. However, crystallization is seeded through stochastic and incoherent nucleation events, limiting the ability to control or pattern the microstructure, texture, and functional properties of polycrystalline materials. We present a universal approach that can program the microstructure of materials through the coherent seeding of otherwise stochastic homogeneous nucleation events. The method relies on creating topographic variations to seed nucleation and growth at designated locations while delaying nucleation elsewhere. Each seed can thus produce a coherent growth front of crystallization with a geometry designated by the shape and arrangement of seeds. Periodic and aperiodic crystalline arrays of functional materials, such as semiconductors, can thus be created on demand and with unprecedented sophistication and ease by patterning the location and shape of the seeds. This approach is used to demonstrate printed arrays of organic thin-film transistors with remarkable performance and reproducibility owing to their demonstrated spatial control over the microstructure of organic and inorganic polycrystalline semiconductors.

Hybrid Perovskite Thin-Film Photovoltaics: In Situ Diagnostics and Importance of the Precursor Solvate Phases.

Solution-processed hybrid perovskite semiconductors attract a great deal of attention, but little is known about their formation process. The one-step spin-coating process of perovskites is investigated in situ, revealing that thin-film formation is mediated by solid-state precursor solvates and their nature. The stability of these intermediate phases directly impacts the quality and reproducibility of thermally converted perovskite films and their photovoltaic performance.

Hybrid organic-inorganic inks flatten the energy landscape in colloidal quantum dot solids.

Bandtail states in disordered semiconductor materials result in losses in open-circuit voltage (Voc) and inhibit carrier transport in photovoltaics. For colloidal quantum dot (CQD) films that promise low-cost, large-area, air-stable photovoltaics, bandtails are determined by CQD synthetic polydispersity and inhomogeneous aggregation during the ligand-exchange process. Here we introduce a new method for the synthesis of solution-phase ligand-exchanged CQD inks that enable a flat energy landscape and an advantageously high packing density. In the solid state, these materials exhibit a sharper bandtail and reduced energy funnelling compared with the previous best CQD thin films for photovoltaics. Consequently, we demonstrate solar cells with higher Voc and more efficient charge injection into the electron acceptor, allowing the use of a closer-to-optimum bandgap to absorb more light. These enable the fabrication of CQD solar cells made via a solution-phase ligand exchange, with a certified power conversion efficiency of 11.28%. The devices are stable when stored in air, unencapsulated, for over 1,000 h.